Abstract: The copper flotation tailings from Konkola Copper
mine in Nchanga, Zambia were used in the study. The purpose of this
study was to determine the leaching characteristics of the tailings
material prior and after the physical beneficiation process is
employed. The Knelson gravity concentrator (KC-MD3) was used for
the beneficiation process. The copper leaching efficiencies and
impurity co-extraction percentages in both the upgraded and the raw
feed material were determined at different pH levels and temperature.
It was observed that the copper extraction increased with an increase
in temperature and a decrease in pH levels. In comparison to the raw
feed sample, the upgraded sample reported a maximum copper
extraction of 69% which was 9%, higher than raw feed % extractions.
The impurity carry over was reduced from 18% to 4 % on the
upgraded sample. The reduction in impurity co-extraction was as a
result of the removal of the reactive gangue elements during the
upgrading process, this minimized the number of side reaction
occurring during leaching.
Abstract: In this paper, FinFET devices are analyzed with
emphasis on sub-threshold leakage current control. This is achieved
through proper biasing of the back gate, and through the use of
asymmetric work functions for the four terminal FinFET devices. We
are also examining different configurations of multiplexers and XOR
gates using transistors of symmetric and asymmetric work functions.
Based on extensive characterization data for MUX circuits, our
proposed configuration using symmetric devices lead to leakage
current and delay improvements of 65% and 47% respectively
compared to results in the literature. For XOR gates, a 90%
improvement in the average leakage current is achieved by using
asymmetric devices. All simulations are based on a 25nm FinFET
technology using the University of Florida UFDG model.
Abstract: A DC-to-DC converter for applications involving a
source with widely varying voltage conditions with loads requiring
constant voltage from full load down to no load is presented.
The switching regulator considered is a Buck converter with Pulse
Skipping Modulation control whereby pulses applied to the switch
are blocked or released on output voltage crossing a predetermined
value. Results of the study on the performance of regulator circuit
are presented. The regulator regulates over a wide input voltage range
with slightly higher ripple content and good transient response. Input
current spectrum indicates a good EMI performance with crowding
of components at low frequency range.
Abstract: Calcium [Ca2+] dynamics is studied as a potential form
of neuron excitability that can control many irregular processes like
metabolism, secretion etc. Ca2+ ion enters presynaptic terminal and
increases the synaptic strength and thus triggers the neurotransmitter
release. The modeling and analysis of calcium dynamics in neuron
cell becomes necessary for deeper understanding of the processes
involved. A mathematical model has been developed for cylindrical
shaped neuron cell by incorporating physiological parameters like
buffer, diffusion coefficient, and association rate. Appropriate initial
and boundary conditions have been framed. The closed form solution
has been developed in terms of modified Bessel function. A computer
program has been developed in MATLAB 7.11 for the whole
approach.
Abstract: this paper focuses on designing of PSS and SVC
controller based on chaos and PSO algorithms to improve the
stability of power system. Single machine infinite bus (SMIB) system
with SVC located at the terminal of generator has been considered to
evaluate the proposed controllers where both SVC and PSS have the
same controller. The coefficients of PSS and SVC controller have
been optimized by chaos and PSO algorithms. Finally the system
with proposed controllers has been simulated for the special
disturbance in input power of generator, and then the dynamic
responses of generator have been presented. The simulation results
showed that the system composed with recommended controller has
outstanding operation in fast damping of oscillations of power system.
Abstract: Nodes in mobile Ad Hoc Network (MANET) do not
rely on a central infrastructure but relay packets originated by other
nodes. Mobile ad hoc networks can work properly only if the
participating nodes collaborate in routing and forwarding. For
individual nodes it might be advantageous not to collaborate, though.
In this conceptual paper we propose a new approach based on
relationship among the nodes which makes them to cooperate in an
Adhoc environment. The trust unit is used to calculate the trust
values of each node in the network. The calculated trust values are
being used by the relationship estimator to determine the relationship
status of nodes. The proposed enhanced protocol was compared with
the standard DSR protocol and the results are analyzed using the
network simulator-2.
Abstract: In this article the influence of higher frequency effects
in addition to a special damper design on the electrical behavior of a
synchronous generator main exciter machine is investigated. On the
one hand these machines are often highly stressed by harmonics from
the bridge rectifier thus facing additional eddy current losses. On the
other hand the switching may cause the excitation of dangerous
voltage peaks in resonant circuits formed by the diodes of the
rectifier and the commutation reactance of the machine. Therefore
modern rotating exciters are treated like synchronous generators
usually modeled with a second order equivalent circuit. Hence the
well known Standstill Frequency Response Test (SSFR) method is
applied to a test machine in order to determine parameters for the
simulation. With these results it is clearly shown that higher
frequencies have a strong impact on the conventional equivalent
circuit model. Because of increasing field displacement effects in the
stranded armature winding the sub-transient reactance is even smaller
than the armature leakage at high frequencies. As a matter of fact this
prevents the algorithm to find an equivalent scheme. This issue is
finally solved using Laplace transfer functions fully describing the
transient behavior at the model ports.
Abstract: This paper presents a study on the thermodynamics
and transport properties of hot potassium carbonate aqueous system
(HPC) using electrolyte non-random two liquid, (ELECNRTL)
model. The operation conditions are varied to determine the system
liquid phase stability range at the standard and critical conditions. A
case study involving 30 wt% K2CO3, H2O standard system at
pressure of 1 bar and temperature range from 280.15 to 366.15 K has
been studied. The estimated solubility index, viscosity, water
activity, and density which obtained from the simulation showed a
good agreement with the experimental work. Furthermore, the
saturation temperature of the solution has been estimated.
Abstract: This is a comprehensive large-sample study of Australian earnings management. Using a sample of 4,844 firm-year observations across nine Australia industries from 2000 to 2006, we find substantial corporate earnings management activity across several Australian industries. We document strong evidence of size and return on assets being primary determinants of earnings management in Australia. The effects of size and return on assets are also found to be dominant in both income-increasing and incomedecreasing earnings manipulation. We also document that that periphery sector firms are more likely to involve larger magnitude of earnings management than firms in the core sector.
Abstract: In the present study, the incorporation of graphene
into blends of acrylonitrile-butadiene-styrene terpolymer with
polypropylene (ABS/PP) was investigated focusing on the
improvement of their thermomechanical characteristics and the effect
on their rheological behavior. The blends were prepared by melt
mixing in a twin-screw extruder and were characterized by measuring
the MFI as well as by performing DSC, TGA and mechanical tests.
The addition of graphene to ABS/PP blends tends to increase their
melt viscosity, due to the confinement of polymer chains motion.
Also, graphene causes an increment of the crystallization temperature
(Tc), especially in blends with higher PP content, because of the
reduction of surface energy of PP nucleation, which is a consequence
of the attachment of PP chains to the surface of graphene through the
intermolecular CH-π interaction. Moreover, the above nanofiller
improves the thermal stability of PP and increases the residue of
thermal degradation at all the investigated compositions of blends,
due to the thermal isolation effect and the mass transport barrier
effect. Regarding the mechanical properties, the addition of graphene
improves the elastic modulus, because of its intrinsic mechanical
characteristics and its rigidity, and this effect is particularly strong in
the case of pure PP.
Abstract: In this report we present a rule-based approach to
detect anomalous telephone calls. The method described here uses
subscriber usage CDR (call detail record) data sampled over two
observation periods: study period and test period. The study period
contains call records of customers- non-anomalous behaviour.
Customers are first grouped according to their similar usage
behaviour (like, average number of local calls per week, etc). For
customers in each group, we develop a probabilistic model to describe
their usage. Next, we use maximum likelihood estimation (MLE) to
estimate the parameters of the calling behaviour. Then we determine
thresholds by calculating acceptable change within a group. MLE is
used on the data in the test period to estimate the parameters of the
calling behaviour. These parameters are compared against thresholds.
Any deviation beyond the threshold is used to raise an alarm. This
method has the advantage of identifying local anomalies as compared
to techniques which identify global anomalies. The method is tested
for 90 days of study data and 10 days of test data of telecom
customers. For medium to large deviations in the data in test window,
the method is able to identify 90% of anomalous usage with less than
1% false alarm rate.
Abstract: This paper presents an experimental investigation on
the machinability of laser-sintered material using small ball end mill focusing on wear mechanisms. Laser-sintered material was produced
by irradiating a laser beam on a layer of loose fine SCM-Ni-Cu powder. Bulk carbon steel JIS S55C was selected as a reference steel.
The effects of powder consolidation mechanisms and unsintered
powder on the tool life and wear mechanisms were carried out. Results indicated that tool life in cutting laser-sintered material is
lower than that in cutting JIS S55C. Adhesion of the work material and chipping were the main wear mechanisms of the ball end mill in
cutting laser-sintered material. Cutting with the unsintered powder
surrounding the tool and laser-sintered material had caused major fracture on the cutting edge.
Abstract: In wireless communication system, a Decision Feedback Equalizer (DFE) to cancel the intersymbol interference (ISI) is required. In this paper, an exact convergence analysis of the (DFE) adapted by the Least Mean Square (LMS) algorithm during the training phase is derived by taking into account the finite alphabet context of data transmission. This allows us to determine the shortest training sequence that allows to reach a given Mean Square Error (MSE). With the intention of avoiding the problem of ill-convergence, the paper proposes an initialization strategy for the blind decision directed (DD) algorithm. This then yields a semi-blind DFE with high speed and good convergence.
Abstract: Since the beginning of human history, human
activities have caused many changes in the environment. Today, a
particular attention should be paid to gaining knowledge about water
quality of wetlands which are pristine natural environments rich in
genetic reserves. If qualitative conditions of industrial areas (in terms
of both physicochemical and biological conditions) are not addressed
properly, they could cause disruption in natural ecosystems,
especially in rivers. With regards to the quality of water resources,
determination of pollutant sources plays a pivotal role in engineering
projects as well as designing water quality control systems. Thus,
using different methods such as flow duration curves, dischargepollution
load model and frequency analysis by HYFA software
package, risk of various industrial pollutants in international and
ecologically important Gavkhoni wetland is analyzed. In this study, a
station located at Varzaneh City is used as the last station on
Zayanderud River, from where the river water is discharged into the
wetland. Results showed that elements- concentrations often
exceeded the allowed level and river water can endanger regional
ecosystem. In addition, if the river discharge is managed on Q25
basis, this basis can lower concentrations of elements, keeping them
within the normal level.
Abstract: An electric power system includes a generating, a
transmission, a distribution, and consumers subsystems. An electrical
power network in Tanzania keeps growing larger by the day and
become more complex so that, most utilities have long wished for
real-time monitoring and remote control of electrical power system
elements such as substations, intelligent devices, power lines,
capacitor banks, feeder switches, fault analyzers and other physical
facilities. In this paper, the concept of automation of management of
power systems from generation level to end user levels was
determined by using Power System Simulator for Engineering
(PSS/E) version 30.3.2.
Abstract: In this paper, a new recursive strategy is proposed for determining $\frac{(n-1)!}{2}$ of $n$th order diagrams. The generalization of $n$th diagram for cross multiplication method were proposed by Pavlovic and Bankier but the specific rule of determining $\frac{(n-1)!}{2}$ of the $n$th order diagrams for square matrix is yet to be discovered. Thus using combinatorial approach, $\frac{(n-1)!}{2}$ of the $n$th order diagrams will be presented as $\frac{(n-1)!}{2}$ starter sets. These starter sets will be generated based on exchanging one element. The advantages of this new strategy are the discarding process was eliminated and the sign of starter set is alternated to each others.
Abstract: This paper deals with the evaluation of flow properties
of polymeric matrix with natural animal fillers. Technical university
of Liberec cooperates on the long-term development of “green
materials“ that should replace conventionally used materials
(especially in automotive industry). Natural fibres (of animal and
plant origin) from all over the world are collected and adapted
(drying, cutting etc.) for extrusion processing. Inside the extruder
these natural additives are blended with polymeric (synthetic and
biodegradable - PLA) matrix and created compound is subsequently
cut for pellets in the wet way. These green materials with unique
recipes are then studied and their mechanical, physical and
processing properties are determined. The main goal of this research
is to develop new ecological materials very similar to unfilled
polymers. In this article the rheological behaviour of chosen natural
animal fibres is introduced considering their shape and surface that
were observed with use of SEM microscopy.
Abstract: In this paper, we study the application of Extreme
Learning Machine (ELM) algorithm for single layered feedforward
neural networks to non-linear chaotic time series problems. In this
algorithm the input weights and the hidden layer bias are randomly
chosen. The ELM formulation leads to solving a system of linear
equations in terms of the unknown weights connecting the hidden
layer to the output layer. The solution of this general system of
linear equations will be obtained using Moore-Penrose generalized
pseudo inverse. For the study of the application of the method we
consider the time series generated by the Mackey Glass delay
differential equation with different time delays, Santa Fe A and
UCR heart beat rate ECG time series. For the choice of sigmoid,
sin and hardlim activation functions the optimal values for the
memory order and the number of hidden neurons which give the
best prediction performance in terms of root mean square error are
determined. It is observed that the results obtained are in close
agreement with the exact solution of the problems considered
which clearly shows that ELM is a very promising alternative
method for time series prediction.
Abstract: This paper presents the work of signal discrimination
specifically for Electrocardiogram (ECG) waveform. ECG signal is
comprised of P, QRS, and T waves in each normal heart beat to
describe the pattern of heart rhythms corresponds to a specific
individual. Further medical diagnosis could be done to determine any
heart related disease using ECG information. The emphasis on QRS
Complex classification is further discussed to illustrate the
importance of it. Pan-Tompkins Algorithm, a widely known
technique has been adapted to realize the QRS Complex
classification process. There are eight steps involved namely
sampling, normalization, low pass filter, high pass filter (build a band
pass filter), derivation, squaring, averaging and lastly is the QRS
detection. The simulation results obtained is represented in a
Graphical User Interface (GUI) developed using MATLAB.
Abstract: In this paper, we consider nested sliding mode control of SISO nonlinear systems, perturbed by bounded matched and unmatched uncertainties. The systems are assumed to be in strict-feedback form. A step wise procedure is introduced to obtain the controller. In each step, a continuous sliding mode controller is designed as virtual control law. Then the next step sliding surface is defined by using this virtual controller. These sliding surfaces are selected as nonlinear static functions of the system states. Finally in the last step, smooth static state feedback control law is determined such that the output reaches the desired set-point while the system is forced arbitrary close to the intersection of sliding surfaces and the states remain bounded.