Abstract: Service life of existing reinforced concrete (RC)
structures in coastal towns of Sabah has been affected very much.
Concrete crack, spalling of concrete cover and reinforcement rusting
of RC buildings are seen even within 5 years of construction in
Sabah. Hence, in this study a new mix design of concrete grout was
developed using locally available materials and investigated under
two curing conditions and workability, compressive strength,
Accelerated Mortar Bar Test (AMBT), water absorption, volume of
permeable voids (VPV), Sorptivity and 90-days salt ponding test
were conducted. The compressive strength of concrete grout at the
age 90 days was found to be 44.49 N/mm2 under water curing. It was
observed that the percentage of mortar bar length change was below
1% for developed concrete grout. The water absorption of the
concrete grout was in between the range of 0.88 % to 3.60 % under
two different curing up to the age 90 days. It was also observed that
the VPV of concrete was in the range of 0 % to 9.75 and 2.44% to
13.05% under water curing and site curing respectively. It was found
that the Sorptivity of the concrete grout under water curing at the age
of 28 days is 0.211mm/√min and at the age 90 day are 0.067
mm/√min. The chloride content decreased greatly, 90% after a depth
of 15 mm. It was noticed that the site cured samples showed higher
chloride contents near surface compared to water cured samples.
This investigation suggested that the developed mix design of
concrete grout using locally available construction materials can be
used for crack repairing of existing RC structures in Sabah.
Abstract: The complex shape of the human pelvic bone was
successfully imaged and modeled using finite element FE processing.
The bone was subjected to quasi-static and dynamic loading
conditions simulating the effect of both weight gain and impact.
Loads varying between 500 – 2500 N (~50 – 250 Kg of weight) was
used to simulate 3D quasi-static weight gain. Two different 3D
dynamic analyses, body free fall at two different heights (1 and 2 m)
and forced side impact at two different velocities (20 and 40 Km/hr)
were also studied. The computed resulted stresses were compared for
the four loading cases, where Von Misses stresses increases linearly
with the weight gain increase under quasi-static loading. For the
dynamic models, the Von Misses stress history behaviors were
studied for the affected area and effected load with respect to time.
The normalization Von Misses stresses with respect to the applied
load were used for comparing the free fall and the forced impact load
results. It was found that under the forced impact loading condition
an over lapping behavior was noticed, where as for the free fall the
normalized Von Misses stresses behavior was found to nonlinearly
different. This phenomenon was explained through the energy
dissipation concept. This study will help designers in different
specialization in defining the weakest spots for designing different
supporting systems.
Abstract: One of the biggest problems of SMEs is their tendencies to financial distress because of insufficient finance background. In this study, an Early Warning System (EWS) model based on data mining for financial risk detection is presented. CHAID algorithm has been used for development of the EWS. Developed EWS can be served like a tailor made financial advisor in decision making process of the firms with its automated nature to the ones who have inadequate financial background. Besides, an application of the model implemented which covered 7,853 SMEs based on Turkish Central Bank (TCB) 2007 data. By using EWS model, 31 risk profiles, 15 risk indicators, 2 early warning signals, and 4 financial road maps has been determined for financial risk mitigation.
Abstract: Efficient storage, transmission and use of video information are key requirements in many multimedia applications currently being addressed by MPEG-4. To fulfill these requirements, a new approach for representing video information which relies on an object-based representation, has been adopted. Therefore, objectbased watermarking schemes are needed for copyright protection. This paper proposes a novel blind object watermarking scheme for images and video using the in place lifting shape adaptive-discrete wavelet transform (SA-DWT). In order to make the watermark robust and transparent, the watermark is embedded in the average of wavelet blocks using the visual model based on the human visual system. Wavelet coefficients n least significant bits (LSBs) are adjusted in concert with the average. Simulation results shows that the proposed watermarking scheme is perceptually invisible and robust against many attacks such as lossy image/video compression (e.g. JPEG, JPEG2000 and MPEG-4), scaling, adding noise, filtering, etc.
Abstract: As we make progressive products for good works, and
future industries want to get higher speed and resolution from various
developments in the robotics as well as precise control system, the
concept of control feedback is getting more important. Within a range
of industrial developments, the concept is most responsible for the
high reliability of a device. We explain an efficient analyzing method
of a rotary encoder such as an incremental type encoder and absolute
type encoder using the LabVIEW program
Abstract: We present an integration approach of a CMOS biosensor into a polymer based microfluidic environment suitable for mass production. It consists of a wafer-level-package for the silicon die and laser bonding process promoted by an intermediate hot melt foil to attach the sensor package to the microfluidic chip, without the need for dispensing of glues or underfiller. A very good condition of the sensing area was obtained after introducing a protection layer during packaging. A microfluidic flow cell was fabricated and shown to withstand pressures up to Δp = 780 kPa without leakage. The employed biosensors were electrically characterized in a dry environment.
Abstract: Cabbage seedlings grown in vitro were exposed to
excess levels of heavy metals, including Cd, Mo, and Zn. High metal
levels affected plant growth at cotyledonary stage. Seedlings under
Cd, Mo, and Zn treatments could not produce root hairs and true
leaves. Under stress conditions, seedlings accumulated a higher
amount of anthocyanins in their cotyledons than those in the control.
The pigments isolated from Cd and Zn stressed seedling cotyledons
appeared as pink, while under Mo stress, was dark pink or purple.
Moreover, excess Mo stress increased antioxidant enzyme activities
of APX, CAT, SOD. These results suggest that, under excess Mo
stress, the induced antioxidant enzyme activity of cabbage seedlings
may function as a protective mechanism to shield the plants from
toxicity and exacerbated growth.
Abstract: This study examines the mediating effects of male
dyadic adjustment on the relationships between attachment and
attributional styles, and both psychological and physical husband
violence. Based on data from 68 married violent men recruited
through community organizations that work with violent men,
regression analyses showed that husbands- dyadic adjustment
mediates the associations between avoidant attachment and
attributional style, and psychological aggression, but not physical
violence. Scientific and clinical implications are discussed
Abstract: Discrete Cosine Transform (DCT) based transform coding is very popular in image, video and speech compression due to its good energy compaction and decorrelating properties. However, at low bit rates, the reconstructed images generally suffer from visually annoying blocking artifacts as a result of coarse quantization. Lapped transform was proposed as an alternative to the DCT with reduced blocking artifacts and increased coding gain. Lapped transforms are popular for their good performance, robustness against oversmoothing and availability of fast implementation algorithms. However, there is no proper study reported in the literature regarding the statistical distributions of block Lapped Orthogonal Transform (LOT) and Lapped Biorthogonal Transform (LBT) coefficients. This study performs two goodness-of-fit tests, the Kolmogorov-Smirnov (KS) test and the 2- test, to determine the distribution that best fits the LOT and LBT coefficients. The experimental results show that the distribution of a majority of the significant AC coefficients can be modeled by the Generalized Gaussian distribution. The knowledge of the statistical distribution of transform coefficients greatly helps in the design of optimal quantizers that may lead to minimum distortion and hence achieve optimal coding efficiency.
Abstract: The significance of psychology in studying politics
is embedded in philosophical issues as well as behavioural
pursuits. For the former is often associated with Sigmund Freud
and his followers. The latter is inspired by the writings of Harold
Lasswell. Political psychology or psychopolitics has its own
impression on political thought ever since it deciphers the concept
of human nature and political propaganda. More importantly,
psychoanalysis views political thought as a textual content which
needs to explore the latent from the manifest content. In other
words, it reads the text symptomatically and interprets the hidden
truth. This paper explains the paradigm of dream interpretation
applied by Freud. The dream work is a process which has four
successive activities: condensation, displacement, representation
and secondary revision. The texts dealing with political though can
also be interpreted on these principles. Freud's method of dream
interpretation draws its source after the hermeneutic model of
philological research. It provides theoretical perspective and
technical rules for the interpretation of symbolic structures. The
task of interpretation remains a discovery of equivalence of
symbols and actions through perpetual analogies. Psychoanalysis
can help in studying political thought in two ways: to study the text
distortion, Freud's dream interpretation is used as a paradigm
exploring the latent text from its manifest text; and to apply Freud's
psychoanalytic concepts and theories ranging from individual mind
to civilization, religion, war and politics.
Abstract: Speeding represents one of the main concerns for road safety and it still is a subject for research. The need to address this problem and to understand why drivers over speed increases especially in Romania, where in 2011, speed was the main cause of car accidents. This article addresses this problem by using the theory of planned behaviour. A questionnaire was administered to a sample of young Romanian drivers (18 to 25 years) and several path analyses were made in order to verify if the model proposed by the theory of planned behaviour fits the data. One interesting result is that perceived behavioural control does not predict the intention to speed or self-reported driving speed, but subjective norms do. This implies that peers and social environment have a greater impact on young Romanian drivers than we thought.
Abstract: In the framework of the image compression by
Wavelet Transforms, we propose a perceptual method by
incorporating Human Visual System (HVS) characteristics in the
quantization stage. Indeed, human eyes haven-t an equal sensitivity
across the frequency bandwidth. Therefore, the clarity of the
reconstructed images can be improved by weighting the quantization
according to the Contrast Sensitivity Function (CSF). The visual
artifact at low bit rate is minimized. To evaluate our method, we use
the Peak Signal to Noise Ratio (PSNR) and a new evaluating criteria
witch takes into account visual criteria. The experimental results
illustrate that our technique shows improvement on image quality at
the same compression ratio.
Abstract: Enterprise Architecture (EA) is a framework for description, coordination and alignment of all activities across the organization in order to achieve strategic goals using ICT enablers. A number of EA-compatible frameworks have been developed. We, in this paper, mainly focus on Federal Enterprise Architecture Framework (FEAF) since its reference models are plentiful. Among these models we are interested here in its business reference model (BRM). The test process is one important subject of an EA project which is to somewhat overlooked. This lack of attention may cause drawbacks or even failure of an enterprise architecture project. To address this issue we intend to use International Software Testing Qualification Board (ISTQB) framework and standard test suites to present a method to improve EA testing process. The main challenge is how to communicate between the concepts of EA and ISTQB. In this paper, we propose a method for integrating these concepts.
Abstract: The aim of this paper is to confirm the effect of key
design parameters, the punch radius and punch angle, on rupture of the
expansion tube using a finite element analysis with a ductile damage
model. The results of the finite element analysis indicated that the
expansion ratio of the tube was mainly affected by the radius of the
punch. However, the rupture was more affected by the punch angle
than the radius of the punch. The existence of a specific punch angle,
at which rupture did not occur, even if the radius of the punch was
increased, was found.
Abstract: We developed a multi-camera control system that a (one) cameraman can operate several cameras at a compact studio. we analyzed a workflow of a cameraman of some program shootings with two cameras and clarified their heavy tasks. The system based on a dynamic workflow which adapts a program progressing and recommends of cameraman. we perform the automation of multicamera controls by modeling of studio environment and perform automatic camera adjustment for suitable angle of view with face detection. Our experiment at a real program shooting showed that one cameraman can carry out the task of shooting sufficiently.
Abstract: This paper presents a new study on the applications of
optimization and regression analysis techniques for optimal
calculation of partial ratios of four-step helical gearboxes for getting
minimal gearbox length. In the paper, basing on the moment
equilibrium condition of a mechanic system including four gear units
and their regular resistance condition, models for determination of the
partial ratios of the gearboxes are proposed. In particular, explicit
models for calculation of the partial ratios are proposed by using
regression analysis. Using these models, the determination of the
partial ratios is accurate and simple.
Abstract: In this article we address the problem of mobile robot formation control. Indeed, the most work, in this domain, have studied extensively classical control for keeping a formation of mobile robots. In this work, we design an FLC (Fuzzy logic Controller) controller for separation and bearing control (SBC). Indeed, the leader mobile robot is controlled to follow an arbitrary reference path, and the follower mobile robot use the FSBC (Fuzzy Separation and Bearing Control) to keep constant relative distance and constant angle to the leader robot. The efficiency and simplicity of this control law has been proven by simulation on different situation.
Abstract: Production of hard-to-cut materials with uncoated carbide cutting tools in turning, not only cause tool life reduction but also, impairs the product surface roughness. In this paper, influence of hot machining method were studied and presented in two cases. Case1-Workpiece surface roughness quality with constant cutting parameter and 300 ºC initial workpiece surface temperature. Case 2- Tool temperature variation when cutting with two speeds 78.5 (m/min) and 51 (m/min). The workpiece material and tool used in this study were AISI 1060 steel (45HRC) and uncoated carbide TNNM 120408-SP10(SANDVIK Coromant) respectively. A gas flam heating source was used to preheating of the workpiece surface up to 300 ºC, causing reduction of yield stress about 15%. Results obtained experimentally, show that the method used can considerably improved surface quality of the workpiece.
Abstract: The objectives of this research were to explore factors
influencing knowledge management process in the manufacturing
industry and develop a model to support knowledge management
processes. The studied factors were technology infrastructure, human
resource, knowledge sharing, and the culture of the organization. The
knowledge management processes included discovery, capture,
sharing, and application. Data were collected through questionnaires
and analyzed using multiple linear regression and multiple
correlation. The results found that technology infrastructure, human
resource, knowledge sharing, and culture of the organization
influenced the discovery and capture processes. However, knowledge
sharing had no influence in sharing and application processes. A
model to support knowledge management processes was developed,
which indicated that sharing knowledge needed further improvement
in the organization.
Abstract: The paper presents a numerical investigation on the
rapid gas decompression in pure nitrogen which is made by using the
one-dimensional (1D) and three-dimensional (3D) mathematical
models of transient compressible non-isothermal fluid flow in pipes.
A 1D transient mathematical model of compressible thermal multicomponent
fluid mixture flow in pipes is presented. The set of the
mass, momentum and enthalpy conservation equations for gas phase
is solved in the model. Thermo-physical properties of multicomponent
gas mixture are calculated by solving the Equation of
State (EOS) model. The Soave-Redlich-Kwong (SRK-EOS) model is
chosen. This model is successfully validated on the experimental data
[1] and shows a good agreement with measurements. A 3D transient
mathematical model of compressible thermal single-component gas
flow in pipes, which is built by using the CFD Fluent code (ANSYS),
is presented in the paper. The set of unsteady Reynolds-averaged
conservation equations for gas phase is solved. Thermo-physical
properties of single-component gas are calculated by solving the Real
Gas Equation of State (EOS) model. The simplest case of gas
decompression in pure nitrogen is simulated using both 1D and 3D
models. The ability of both models to simulate the process of rapid
decompression with a high order of agreement with each other is
tested. Both, 1D and 3D numerical results show a good agreement
between each other. The numerical investigation shows that 3D CFD
model is very helpful in order to validate 1D simulation results if the
experimental data is absent or limited.