Abstract: Interpolated contour maps drawn for aluminum,
copper and molybdenum in downstream monitoring boreholes of
water dam in Miduk Copper Complex and the values of pH, redox
potential (Eh) and distance from water dam indicate different trends
of variation and behavior of these three elements in downward
groundwater resources. As these maps exhibit, aluminum is dominant
in the most alkaline (pH = 9-11) borehole (MB5) to water dam. The
highest concentration of molybdenum is found in the nearest
borehole (MB6) to water dam. Main concentration of copper is
observed in the most oxidized borehole (MB3 with Eh=293.2mV).
The spatial difference among sampling stations can be attributed to
the existence of faults and diaclases in the geologic structure of
Miduk region which causes the groundwater sampling sites to be
impressed by different contamination sources (toe seepage and upper
seepage water originated from different zones of tailings dump).
Abstract: Estimates of temperature values at a specific time of day, from daytime and daily profiles, are needed for a number of environmental, ecological, agricultural and technical applications, ranging from natural hazards assessments, crop growth forecasting to design of solar energy systems. The scope of this research is to investigate the efficiency of data mining techniques in estimating minimum, maximum and mean temperature values. For this reason, a number of experiments have been conducted with well-known regression algorithms using temperature data from the city of Patras in Greece. The performance of these algorithms has been evaluated using standard statistical indicators, such as Correlation Coefficient, Root Mean Squared Error, etc.
Abstract: In the past, there were many bridge-s collapses due to
lack of bridge structural capacity information. Most of concrete
bridge health was relied on information from visual inspection, which
sometime was inadequate. This study was conducted in order to
investigate relationship between bridge structural condition and
bridge visual condition. This study was a part of a big project
conducted at Department of Highways of Thailand. In this study, 31
bridges including slab-type bridges, plank-girder bridges, prestressed
box-beam bridges, prestressed I-girder bridges and prestressed multibeam
bridges were selected for visual inspection and load test. It was
found a positive correlation between bridge appearance and bridge-s
load carrying capacity. However, statistical characteristic revealed
low correlation between them.
Abstract: The concerns of education and practice of architecture
do not necessarily overlap. Indeed the gap between them could be
seen increasingly and less frequently bridged. We suggest that
changing in architecture education and clarifying the relationship
between these two can help to find and address the opportunities and
unique positions to bridge this gulf.
Abstract: A novel feature selection strategy to improve the recognition accuracy on the faces that are affected due to nonuniform illumination, partial occlusions and varying expressions is proposed in this paper. This technique is applicable especially in scenarios where the possibility of obtaining a reliable intra-class probability distribution is minimal due to fewer numbers of training samples. Phase congruency features in an image are defined as the points where the Fourier components of that image are maximally inphase. These features are invariant to brightness and contrast of the image under consideration. This property allows to achieve the goal of lighting invariant face recognition. Phase congruency maps of the training samples are generated and a novel modular feature selection strategy is implemented. Smaller sub regions from a predefined neighborhood within the phase congruency images of the training samples are merged to obtain a large set of features. These features are arranged in the order of increasing distance between the sub regions involved in merging. The assumption behind the proposed implementation of the region merging and arrangement strategy is that, local dependencies among the pixels are more important than global dependencies. The obtained feature sets are then arranged in the decreasing order of discriminating capability using a criterion function, which is the ratio of the between class variance to the within class variance of the sample set, in the PCA domain. The results indicate high improvement in the classification performance compared to baseline algorithms.
Abstract: Periodicities in the environmetric time series can be
idyllically assessed by utilizing periodic models. In this
communication fugitive emission of gases from open sewer channel
Lyari which follows periodic behaviour are approximated by
employing periodic autoregressive model of order p. The orders of
periodic model for each season are selected through the examination
of periodic partial autocorrelation or information criteria. The
parameters for the selected order of season are estimated individually
for each emitted air toxin. Subsequently, adequacies of fitted models
are established by examining the properties of the residual for each
season. These models are beneficial for schemer and administrative
bodies for the improvement of implemented policies to surmount
future environmental problems.
Abstract: Iris-based biometric authentication is gaining importance
in recent times. Iris biometric processing however, is a complex
process and computationally very expensive. In the overall processing
of iris biometric in an iris-based biometric authentication system,
feature processing is an important task. In feature processing, we extract
iris features, which are ultimately used in matching. Since there
is a large number of iris features and computational time increases
as the number of features increases, it is therefore a challenge to
develop an iris processing system with as few as possible number of
features and at the same time without compromising the correctness.
In this paper, we address this issue and present an approach to feature
extraction and feature matching process. We apply Daubechies D4
wavelet with 4 levels to extract features from iris images. These
features are encoded with 2 bits by quantizing into 4 quantization
levels. With our proposed approach it is possible to represent an
iris template with only 304 bits, whereas existing approaches require
as many as 1024 bits. In addition, we assign different weights to
different iris region to compare two iris templates which significantly
increases the accuracy. Further, we match the iris template based on
a weighted similarity measure. Experimental results on several iris
databases substantiate the efficacy of our approach.
Abstract: Although the field of parametric Pattern Recognition (PR) has been thoroughly studied for over five decades, the use of the Order Statistics (OS) of the distributions to achieve this has not been reported. The pioneering work on using OS for classification was presented in [1] for the Uniform distribution, where it was shown that optimal PR can be achieved in a counter-intuitive manner, diametrically opposed to the Bayesian paradigm, i.e., by comparing the testing sample to a few samples distant from the mean. This must be contrasted with the Bayesian paradigm in which, if we are allowed to compare the testing sample with only a single point in the feature space from each class, the optimal strategy would be to achieve this based on the (Mahalanobis) distance from the corresponding central points, for example, the means. In [2], we showed that the results could be extended for a few symmetric distributions within the exponential family. In this paper, we attempt to extend these results significantly by considering asymmetric distributions within the exponential family, for some of which even the closed form expressions of the cumulative distribution functions are not available. These distributions include the Rayleigh, Gamma and certain Beta distributions. As in [1] and [2], the new scheme, referred to as Classification by Moments of Order Statistics (CMOS), attains an accuracy very close to the optimal Bayes’ bound, as has been shown both theoretically and by rigorous experimental testing.
Abstract: Synchronization between 0.1 Hz oscillations in heart rate and blood pressure is studied and its change during vertical tilt is evaluated in 37 myocardial infarction patients. Two groups of patients are identified with decreased and increased, respectively, synchronization of the studied oscillations as a response to a tilt test. It is shown that assessment of synchronization of 0.1 Hz oscillations as a response to vertical tilt can be used as a guideline for selecting optimal dose of beta-blocker treatment in post-myocardial infarction patients.
Abstract: Depressurization and pressurization streams in
industrial systems constitute a work exchange network (WEN). In this
paper, a novel graphical approach for targeting energy conservation
potential of a WEN is proposed. Through constructing the composite
work curves in the pressure-work diagram and assuming all of the
mechanical energy of the depressurization streams is recovered by
expanders, the maximum work target of a WEN can be determined via
the proposed targeting steps. A WEN in an ammonia production
process is used as a case study to illustrate the applicability of the
proposed graphical approach.
Abstract: Due to adverse pressure gradient along the diverging
walls of wide-angled diffusers, the attached flow separates from
one wall and remains attached permanently to the other wall in a
process called stalling. Stalled diffusers render the whole fluid flow
system, in which they are part of, very inefficient. There is then an
engineering need to try to understand the whole process of diffuser
stall if any meaningful attempts to improve on diffuser efficiency
are to be made. In this regard, this paper provides a data bank
contribution for the mean flow-field in wide-angled diffusers where
the complete velocity and static pressure fields, and pressure recovery
data for diffusers in the fully stalled flow regime are experimentally
measured. The measurements were carried out at Reynolds numbers
between 1.07×105 and 2.14×105 based on inlet hydraulic diameter
and centreline velocity for diffusers whose divergence angles were
between 30Ôùª and 50Ôùª. Variation of Reynolds number did not significantly
affect the velocity and static pressure profiles. The wall static
pressure recovery was found to be more sensitive to changes in the
Reynolds number. By increasing the velocity from 10 m/s to 20 m/s,
the wall static pressure recovery increased by 8.31%. However, as the
divergence angle was increased, a similar increase in the Reynolds
number resulted in a higher percentage increase in pressure recovery.
Experimental results showed that regardless of the wall to which
the flow was attached, both the velocity and pressure fields were
replicated with discrepancies below 2%.
Abstract: Palm methyl ester (PME) is one of the alternative
biomass fuels to liquid fossil fuels. To investigate the combustion
characteristics of PME as an alternative fuel for gas turbines, combustion experiments using two types of burners under atmospheric
pressure were performed. One of the burners has a configuration
making strong non-premixed flame, whereas the other has a
configuration promoting prevaporization of fuel droplets. The results
show that the NOx emissions can be reduced by employing the latter burner without accumulation of soot when PME is used as a fuel. A
burner configuration promoting prevaporzation of fuel droplets is
recommended for PME.
Abstract: The most common forensic activity is searching a hard
disk for string of data. Nowadays, investigators and analysts are
increasingly experiencing large, even terabyte sized data sets when
conducting digital investigations. Therefore consecutive searching can
take weeks to complete successfully. There are two primary search
methods: index-based search and bitwise search. Index-based
searching is very fast after the initial indexing but initial indexing
takes a long time. In this paper, we discuss a high speed bitwise search
model for large-scale digital forensic investigations. We used pattern
matching board, which is generally used for network security, to
search for string and complex regular expressions. Our results indicate
that in many cases, the use of pattern matching board can substantially
increase the performance of digital forensic search tools.
Abstract: Internet addiction has become a critical problem on
adolescents in Taiwan, and its negative effects on various dimensions
of adolescent development caught the attention of educational and
psychological experts. This study examined the correlation between
cognitive (locus of control) and emotion (emotion venting strategies)
factors on internet addiction of adolescents in Taiwan. Using the
Compulsive Internet Use (CIU) and the Emotion Venting Strategy
scales, a survey was conducted and 215 effective samples (students
ranging from12 to14 years old) returned. Quantitative analysis
methods such as descriptive statistics, t-test, ANOVA, Pearson
correlations and multiple regression were adopted. The results were as
follows: 1. Severity of Internet addiction has significant gender
differences; boys were at a higher risk than girls in becoming addicted
to the Internet. 2. Emotion venting, locus of control and internet
addiction have been shown to be positive correlated with one another.
3. Setting the locus of control as the control variable, emotion venting
strategy has positive and significant contribution to internet addiction.
The results of this study suggest that coaching deconstructive emotion
strategies and cognitive believes are encouraged to integrate with
actual field work.
Abstract: Constant amplitude fatigue crack growth (FCG) tests
were performed on dissimilar metal welded plates of Type 316L
Stainless Steel (SS) and IS 2062 Grade A Carbon steel (CS). The
plates were welded by TIG welding using SS E309 as electrode. FCG
tests were carried on the Side Edge Notch Tension (SENT)
specimens of 5 mm thickness, with crack initiator (notch) at base
metal region (BM), weld metal region (WM) and heat affected zones
(HAZ). The tests were performed at a test frequency of 10 Hz and at
load ratios (R) of 0.1 & 0.6. FCG rate was found to increase with
stress ratio for weld metals and base metals, where as in case of
HAZ, FCG rates were almost equal at high ΔK. FCG rate of HAZ of
stainless steel was found to be lowest at low and high ΔK. At
intermediate ΔK, WM showed the lowest FCG rate. CS showed
higher crack growth rate at all ΔK. However, the scatter band of data
was found to be narrow. Fracture toughness (Kc) was found to vary
in different locations of weldments. Kc was found lowest for the
weldment and highest for HAZ of stainless steel. A novel method of
characterizing the FCG behavior using an Infrared thermography
(IRT) camera was attempted. By monitoring the temperature rise at
the fast moving crack tip region, the amount of plastic deformation
was estimated.
Abstract: In this study, a novel approach of image embedding is introduced. The proposed method consists of three main steps. First, the edge of the image is detected using Sobel mask filters. Second, the least significant bit LSB of each pixel is used. Finally, a gray level connectivity is applied using a fuzzy approach and the ASCII code is used for information hiding. The prior bit of the LSB represents the edged image after gray level connectivity, and the remaining six bits represent the original image with very little difference in contrast. The proposed method embeds three images in one image and includes, as a special case of data embedding, information hiding, identifying and authenticating text embedded within the digital images. Image embedding method is considered to be one of the good compression methods, in terms of reserving memory space. Moreover, information hiding within digital image can be used for security information transfer. The creation and extraction of three embedded images, and hiding text information is discussed and illustrated, in the following sections.
Abstract: Innovations and innovative activity get the increasing
value for successful financial and economic activity of the countries
and regions. The level of innovative sphere development determines
place of a country or a region in world economy and forms a basis of
steady economic growth. This article is devoted to different aspects
of organization of the national economic safety in the conditions of
innovative development, its problems, risks and threats. Economy
can be considered as aspiring for transition to innovative way only
with finding of economic safety: financial independence, power
stability and technological progress. There are statistical indicators,
defining the level of economic security and factors, threatening
economic safety of the state. The research is based on the analysis of
factors and indicators in conditions of innovative development. The
paper is illustrated by the examples of possible estimated system of
the economic safety level.
Abstract: Currently, a large number of license activities (Early
Site Permits, Combined Operating License, reactor certifications,
etc.), are pending for review before the United States Nuclear
Regulatory Commission (US NRC). Much of the senior staff at the
NRC is now committed to these review and licensing actions. To
address this additional workload, the NRC has recruited a large
number of new Regulatory Staff for dealing with these and other
regulatory actions such as the US Fleet of Research and Test Reactors
(RTRs). These reactors pose unusual demands on Regulatory Staff
since the US Fleet of RTRs, although few (32 Licensed RTRs as of
2010), they represent a broad range of reactor types, operations, and
research and training aspects that nuclear reactor power plants (such
as the 104 LWRs) do not pose. The NRC must inspect and regulate
all these facilities. This paper addresses selected training topics and
regulatory activities providedNRC Inspectors for RTRs.
Abstract: Homogeneous composites of alumina and zirconia
with a small amount of MgO (99%) were obtained for ZTA ceramic containing 0.05 wt% MgO in
1500 °C.
Abstract: Use of microemulsion in enhanced oil recovery has become more attractive in recent years because of its high level of extraction efficiency. Experimental investigations have been made on characterization of microemulsions of oil-brinesurfactant/ cosurfactant system for its use in enhanced oil recovery (EOR). Sodium dodecyl sulfate, propan-1-ol and heptane were selected as surfactant, cosurfactant and oil respectively for preparation of microemulsion. The effects of salinity on the relative phase volumes and solubilization parameters have also been studied. As salinity changes from low to high value, phase transition takes place from Winsor I to Winsor II via Winsor III. Suitable microemulsion composition has been selected based on its stability and ability to reduce interfacial tension. A series of flooding experiments have been performed using the selected microemulsion. The flooding experiments were performed in a core flooding apparatus using uniform sand pack. The core holder was tightly packed with uniform sands (60-100 mesh) and saturated with brines of different salinities. It was flooded with the brine at 25 psig and the absolute permeability was calculated from the flow rate of the through sand pack. The sand pack was then flooded with the crude oil at 800 psig to irreducible water saturation. The initial water saturation was determined on the basis of mass balance. Waterflooding was conducted by placing the coreholder horizontally at a constant injection pressure at 200 pisg. After water flooding, when water-cut reached above 95%, around 0.5 pore volume (PV) of the above microemulsion slug was injected followed by chasing water. The experiments were repeated using different composition of microemulsion slug. The additional recoveries were calculated by material balance. Encouraging results with additional recovery more than 20% of original oil in place above the conventional water flooding have been observed.