Abstract: Barley (Hordeum vulgare L.), vetch (Vicia villosa),
and grass pea (Lathyrus sativus L.) monocultures as well as mixtures
of barley with each of the above legumes, in three seeding ratios (i.e.,
barley: legume 75:25, 50:50 and 25:75, based on seed numbers) were
used to investigated forage yield and competition indices. The results
showed that intercropping reduced the dry matter yield of the three
component plants, compared with their respective monocrops. The
greatest value of total dry matter yield was obtained from barley25-
grasspea75 (5.44 t ha-1) mixture, followed by grass pea sole crop (4.99
t ha-1). The total actual yield loss (AYL) values were positive and
greater than 0 in all mixtures, indicating an advantage from
intercropping over sole crops. Intercropped barley had a higher
relative crowding coefficient (K=1.64) than intercropped legumes
(K=1.20), indicating that barley was more competitive than legumes
in mixtures. Furthermore, grass pea was more competitive than vetch
in mixtures with barley. The highest land equivalent ratio (LER),
system productivity index (SPI) and monetary advantage index
(MAI) were obtained when barley was mixed at a rate of 25% with
75% seed rate of grass pea. It is concluded that intercropping of
barley with grass pea has a good potential to improve the
performance of forage with high land-use efficiency.
Abstract: Steel slag is a by-product of the steel industry and can
be used potentially as aggregate in the asphalt mixture. This study
evaluates the use of Steel Slag Aggregates (SSA) as a substitute for
natural aggregates in the production of hot mix asphalt (HMA) for
road construction. Based on intensive laboratory testing program, the
characteristic properties of SSA were assessed to determine its
suitability to be used in HMA. Four different percentages (0, 50, 75,
and 100%) of SSA were used, and the proposed mix designs for
HMA were conducted in accordance with Marshall mix design. The
experiment results revealed that the addition of SSA has a significant
improvement on the properties of HMA. An increase in density and
stability and a reduction in flow and air voids values were clearly
observed in specimens prepared with 100% SSA. It is concluded that
the steel slag can be considered reasonable alternative source of
aggregate for concrete asphalt mixture production.
Abstract: A solar dish collector has been designed, fabricated
and tested for its performance on 10-03-2015 in Salem, Tamilnadu,
India. The experiments on cooking vessels of coated and un-coated
with 5 Liters capacity have been used for cooking Rice. The results
are shown in graphs. The solar cooker is always capable of cooking
food within the expected length of time and based on the solar
radiation levels. With minimum cooking power, the coated pressure
cooker of 5 Liters capacity cooks the food at faster manner. This is
due to the conductivity of the coating material provided in the cooker.
Abstract: In this paper, the problem of stability and stabilization
for neutral delay-differential systems with infinite delay is
investigated. Using Lyapunov method, new delay-independent
sufficient condition for the stability of neutral systems with infinite
delay is obtained in terms of linear matrix inequality (LMI).
Memory-less state feedback controllers are then designed for the
stabilization of the system using the feasible solution of the resulting
LMI, which are easily solved using any optimization algorithms.
Numerical examples are given to illustrate the results of the proposed
methods.
Abstract: In order to obtain efficient pollutants removal in
small-scale wastewater treatment plants, uniform water flow has to be
achieved. The experimental setup, designed for treating high-load
wastewater (leachate), consists of two aerobic biological reactors and
a lamellar settler. Both biological tanks were aerated by using three
different types of aeration systems - perforated pipes, membrane air
diffusers and tube ceramic diffusers. The possibility of homogenizing
the water mass with each of the air diffusion systems was evaluated
comparatively. The oxygen concentration was determined by optical
sensors with data logging. The experimental data was analyzed
comparatively for all three different air dispersion systems aiming to
identify the oxygen concentration variation during different
operational conditions. The Oxygenation Capacity was calculated for
each of the three systems and used as performance and selection
parameter. The global mass transfer coefficients were also evaluated
as important tools in designing the aeration system. Even though
using the tubular porous diffusers leads to higher oxygen
concentration compared to the perforated pipe system (which
provides medium-sized bubbles in the aqueous solution), it doesn’t
achieve the threshold limit of 80% oxygen saturation in less than 30
minutes. The study has shown that the optimal solution for the
studied configuration was the radial air diffusers which ensure an
oxygen saturation of 80% in 20 minutes. An increment of the values
was identified when the air flow was increased.
Abstract: Standard Gibbs energy of formation ΔGfor(298.15) of
lanthanide-iron double oxides of garnet-type crystal structure
R3Fe5O12 - RIG (R – are rare earth ions) from initial oxides are
evaluated. The calculation is based on the data of standard entropies
S298.15 and standard enthalpies ΔH298.15 of formation of compounds
which are involved in the process of garnets synthesis. Gibbs energy
of formation is presented as temperature function ΔGfor(T) for the
range 300-1600K. The necessary starting thermodynamic data were
obtained from calorimetric study of heat capacity – temperature
functions and by using the semi-empirical method for calculation of
ΔH298.15 of formation. Thermodynamic functions for standard
temperature – enthalpy, entropy and Gibbs energy - are
recommended as reference data for technological evaluations.
Through the structural series of rare earth-iron garnets the correlation
between thermodynamic properties and characteristics of lanthanide
ions are elucidated.
Abstract: Low Temperature Matrix Isolation - Electron
Paramagnetic Resonance (LTMI-EPR) Spectroscopy was utilized to
identify the species of iron oxide nanoparticles generated during the
oxidative pyrolysis of 1-methylnaphthalene (1-MN). The otherwise
gas-phase reactions of 1--MN were impacted by a polypropylenimine
tetra-hexacontaamine dendrimer complexed with iron (III) nitrate
nonahydrate diluted in air under atmospheric conditions. The EPR
fine structure of Fe (III)2O3 nanoparticles clusters, characterized by gfactors
of 2.00, 2.28, 3.76 and 4.37 were detected on a cold finger
maintained at 77 K after accumulation over a multitude of
experiments. Additionally, a high valence Fe (IV) paramagnetic
intermediate and superoxide anion-radicals, O2•- adsorbed on
nanoparticle surfaces in the form of Fe (IV) --- O2•- were detected
from the quenching area of Zone 1 in the gas-phase.
Abstract: The present study applies the inverse method and
three-dimensional CFD commercial software in conjunction with the
experimental temperature data to investigate the heat transfer and fluid
flow characteristics of the plate-fin heat sink in a rectangular closed
enclosure. The inverse method with the finite difference method and
the experimental temperature data is applied to determine the
approximate heat transfer coefficient. Later, based on the obtained
results, the zero-equation turbulence model is used to obtain the heat
transfer and fluid flow characteristics between two fins. T0 validate
the accuracy of the results obtained, the comparison of the heat transfer
coefficient is made. The obtained temperature at selected
measurement locations of the fin is also compared with experimental
data. The effect of the height of the rectangular enclosure on the
obtained results is discussed.
Abstract: Determination of genetic variation is useful for plant
breeding and hence production of more efficient plant species under
different conditions, like drought stress. In this study a sample of 28
recombinant inbred lines (RILs) of wheat developed from the cross of
Norstar and Zagross varieties, together with their parents, were
evaluated for two years (2010-2012) under normal and water stress
conditions using split plot design with three replications. Main plots
included two irrigation treatments of 70 and 140 mm evaporation
from Class A pan and sub-plots consisted of 30 genotypes. The effect
of genotypes and interaction of genotypes with years and water
regimes were significant for all characters. Significant genotypic
effect implies the existence of genetic variation among the lines
under study. Heritability estimates were high for 1000 grain weight
(0.87). Biomass and grain yield showed the lowest heritability values
(0.42 and 0.50, respectively). Highest genotypic and phenotypic
coefficients of variation (GCV and PCV) belonged to harvest index.
Moderate genetic advance for most of the traits suggested the
feasibility of selection among the RILs under investigation. Some
RILs were higher yielding than either parent at both environments.
Abstract: This paper presents a methodology for probabilistic
assessment of bearing capacity and prediction of failure mechanism
of masonry vaults at the ultimate state with consideration of the
natural variability of Young’s modulus of stones. First, the
computation model is explained. The failure mode corresponds to the
four-hinge mechanism. Based on this consideration, the study of a
vault composed of 16 segments is presented. The Young’s modulus of
the segments is considered as random variable defined by a mean
value and a coefficient of variation. A relationship linking the vault
bearing capacity to the voussoirs modulus variation is proposed. The
most probable failure mechanisms, in addition to that observed in the
deterministic case, are identified for each variability level as well as
their probability of occurrence. The results show that the mechanism
observed in the deterministic case has decreasing probability of
occurrence in terms of variability, while the number of other
mechanisms and their probability of occurrence increases with the
coefficient of variation of Young’s modulus. This means that if a
significant change in the Young’s modulus of the segments is proven,
taking it into account in computations becomes mandatory, both for
determining the vault bearing capacity and for predicting its failure
mechanism.
Abstract: New environmental regulations and the increasing
market preference for companies that respect the ecosystem had
encouraged the industry to look after new treatments for its effluents.
The sugar industry, one of the largest emitter of environmental
pollutants, follows this tendency. Membrane technology is
convenient for separation of suspended solids, colloids and high
molecular weight materials that are present in a wastewater from
sugar industry. The idea is to microfilter the wastewater, where the
permeate passes through the membrane and becomes available for
recycle and re-use in the sugar manufacturing process. For
microfiltration of this effluent a tubular ceramic membrane was used
with a pore size of 200 nm at transmembrane pressure in range of 1–3
bars and in range of flow rate of 50–150 l/h. Kenics static mixer was
used for permeate flux enhancement. Turbidity and suspended solids
were removed and the permeate flux was continuously monitored
during the microfiltration process. The flux achieved after 90 minutes
of microfiltration was in a range of 50–70 l/m2h. The obtained
turbidity decrease was in the range of 50-99 % and total amount of
suspended solids was removed.
Abstract: The possibility of application the dietary fibers in
production of crackers was observed in this work, as well as their
influence on rheological and textural properties on the dough for
crackers and influence on sensory properties of obtained crackers.
Three different dietary fibers, oat, potato and pea fibers, replaced
10% of wheat flour. Long fermentation process and baking test
method were used for crackers production. The changes of dough for
crackers were observed by rheological methods of determination the
viscoelastic dough properties and by textural measurements. Sensory
quality of obtained crackers was described using quantity descriptive
method (QDA) by trained members of descriptive panel. Additional
analysis of crackers surface was performed by videometer. Based on
rheological determination, viscoelastic properties of dough for
crackers were reduced by application of dietary fibers. Manipulation
of dough with 10% of potato fiber was disabled, thus the recipe
modification included increase in water content at 35%. Dough
compliance to constant stress for samples with dietary fibers
decreased, due to more rigid and stiffer dough consistency compared
to control sample. Also, hardness of dough for these samples
increased and dough extensibility decreased. Sensory properties of
final products, crackers, were reduced compared to control sample.
Application of dietary fibers affected mostly hardness, structure and
crispness of the crackers. Observed crackers were low marked for
flavor and taste, due to influence of fibers specific aroma. The sample
with 10% of potato fibers and increased water content was the most
adaptable to applied stresses and to production process. Also this
sample was close to control sample without dietary fibers by
evaluation of sensory properties and by results of videometer method.
Abstract: In this paper, a new SMC (Sliding Mode Control)
method with MP (Model Predictive Control) integral action for the
slip suppression of EV (Electric Vehicle) under braking is proposed.
The proposed method introduce the integral term with standard SMC
gain , where the integral gain is optimized for each control period by
the MPC algorithms. The aim of this method is to improve the safety
and the stability of EVs under braking by controlling the wheel slip
ratio. There also include numerical simulation results to demonstrate
the effectiveness of the method.
Abstract: Indonesia has experienced annual forest fires that have
rapidly destroyed and degraded its forests. Fires in the peat swamp
forests of Riau Province, have set the stage for problems to worsen,
this being the ecosystem most prone to fires (which are also the most
difficult, to extinguish). Despite various efforts to curb deforestation,
and forest degradation processes, severe forest fires are still
occurring. To find an effective solution, the basic causes of the
problems must be identified. It is therefore critical to have an indepth
understanding of the underlying causal factors that have
contributed to deforestation and forest degradation as a whole, in
order to attain reductions in their rates. An assessment of the drivers of deforestation and forest
degradation was carried out, in order to design and implement
measures that could slow these destructive processes. Research was
conducted in Giam Siak Kecil–Bukit Batu Biosphere Reserve
(GSKBB BR), in the Riau Province of Sumatera, Indonesia. A
biosphere reserve was selected as the study site because such reserves
aim to reconcile conservation with sustainable development. A
biosphere reserve should promote a range of local human activities,
together with development values that are in line spatially and
economically with the area conservation values, through use of a
zoning system. Moreover, GSKBB BR is an area with vast peatlands,
and is experiencing forest fires annually. Various factors were
analysed to assess the drivers of deforestation and forest degradation
in GSKBB BR; data were collected from focus group discussions
with stakeholders, key informant interviews with key stakeholders,
field observation and a literature review. Landsat satellite imagery was used to map forest-cover changes
for various periods. Analysis of landsat images, taken during the
period 2010-2014, revealed that within the non-protected area of core
zone, there was a trend towards decreasing peat swamp forest areas,
increasing land clearance, and increasing areas of community oilpalm
and rubber plantations. Fire was used for land clearing and most
of the forest fires occurred in the most populous area (the transition
area). The study found a relationship between the deforested/
degraded areas, and certain distance variables, i.e. distance from
roads, villages and the borders between the core area and the buffer
zone. The further the distance from the core area of the reserve, the
higher was the degree of deforestation and forest degradation. Research findings suggested that agricultural expansion may be
the direct cause of deforestation and forest degradation in the reserve,
whereas socio-economic factors were the underlying driver of forest
cover changes; such factors consisting of a combination of sociocultural,
infrastructural, technological, institutional (policy and governance), demographic (population pressure) and economic
(market demand) considerations. These findings indicated that local
factors/problems were the critical causes of deforestation and
degradation in GSKBB BR. This research therefore concluded that
reductions in deforestation and forest degradation in GSKBB BR
could be achieved through ‘local actor’-tailored approaches such as
community empowerment.
Abstract: Effects of nicotine on pre-partum body weight and
preimplantation embryonic development has been reported
previously. Present study was conducted to determine the effects of
annatto (Bixa orellana)-derived delta-tocotrienol (TCT) (with
presence of 10% gamma-TCT isomer) on the nicotine-induced
reduction in body weight and 8-cell embryonic growth in mice.
Twenty-four 6-8 weeks old (23-25g) female balb/c mice were
randomly divided into four groups (G1-G4; n=6). Those groups were
subjected to the following treatments for 7 consecutive days: G1
(control) were gavaged with 0.1 ml tocopherol stripped corn oil. G2
was subcutaneously (s.c.) injected with 3 mg/kg/day of nicotine. G3
received concurrent treatment of nicotine (3 mg/kg/day) and 60
mg/kg/day of δ-TCT mixture (contains 90% delta & 10% gamma
isomers) and G4 was given 60 mg/kg/day of δ-TCT mixture alone.
Body weights were recorded daily during the treatment. On Day 8,
females were superovulated with 5 IU Pregnant Mare’s Serum
Gonadotropin (PMSG) for 48 hours followed with 5 IU human
Chorionic Gonadotropin (hCG) before mated with males at the ratio
of 1:1. Females were sacrificed by cervical dislocation for embryo
collection 48 hours post-coitum. Collected embryos were cultured in
vitro. Results showed that throughout Day 1 to Day 7, the body
weight of nicotine treated group (G2) was significantly lower
(p
Abstract: Industries produce millions of cubic meters of effluent
every year and the wastewater produced may be released into the
surrounding water bodies, treated on-site or at municipal treatment
plants. The determination of organic matter in the wastewater
generated is very important to avoid any negative effect on the
aquatic ecosystem. The scope of the present work is to assess the
physicochemical composition of the wastewater produced from one
of the brewery industry in South Africa. This is to estimate the
environmental impact of its discharge into the receiving water bodies
or the municipal treatment plant. The parameters monitored for the
quantitative analysis of brewery wastewater include biological
oxygen demand (BOD5), chemical oxygen demand (COD), total
suspended solids, volatile suspended solids, ammonia, total oxidized
nitrogen, nitrate, nitrite, phosphorus and alkalinity content. In
average, the COD concentration of the brewery effluent was 5340.97
mg/l with average pH values of 4.0 to 6.7. The BOD5 and the solids
content of the wastewater from the brewery industry were high. This
means that the effluent is very rich in organic content and its
discharge into the water bodies or the municipal treatment plant could
cause environmental pollution or damage the treatment plant. In
addition, there were variations in the wastewater composition
throughout the monitoring period. This might be as a result of
different activities that take place during the production process, as
well as the effects of peak period of beer production on the water
usage.
Abstract: Different terms of the Statistical Process Control (SPC)
has sketch in the fuzzy environment. However, Measurement System
Analysis (MSA), as a main branch of the SPC, is rarely investigated
in fuzzy area. This procedure assesses the suitability of the data to be
used in later stages or decisions of the SPC. Therefore, this research
focuses on some important measures of MSA and through a new
method introduces the measures in fuzzy environment. In this
method, which works based on Buckley approach, imprecision and
vagueness nature of the real world measurement are considered
simultaneously. To do so, fuzzy version of the gauge capability (Cg
and Cgk) are introduced. The method is also explained through
example clearly.
Abstract: The recent interest in alternative and renewable
energy systems results in increased installed capacity ratio of such
systems in total energy production of the world. Specifically, Wind
Energy Conversion Systems (WECS) draw significant attention
among possible alternative energy options, recently. On the contrary
of the positive points of penetrating WECS in all over the world in
terms of environment protection, energy independence of the
countries, etc., there are significant problems to be solved for the grid
connection of large scale WECS. The reactive power regulation,
voltage variation suppression, etc. can be presented as major issues to
be considered in this regard. Thus, this paper evaluates the
application of a Static VAr Compensator (SVC) unit for the reactive
power regulation and operation continuity of WECS during a fault
condition. The system is modeled employing the IEEE 13 node test
system. Thus, it is possible to evaluate the system performance with
an overall grid simulation model close to real grid systems. The
overall simulation model is developed in
MATLAB/Simulink/SimPowerSystems® environments and the
obtained results effectively match the target of the provided study.
Abstract: The development of transport systems has negative
impacts on the environment although it has beneficial effects on
society. The car policy caused many problems such as: - the
spectacular growth of fuel consumption hence the very vast increase
in urban pollution, traffic congestion in certain places and at certain
times, the increase in the number of accidents. The exhaust emissions
from cars and weather conditions are the main factors that determine
the level of pollution in urban atmosphere. These conditions lead to
the phenomenon of heat transfer and radiation occurring between the
air and the soil surface of any town. These exchanges give rise, in
urban areas, to the effects of heat islands that correspond to the
appearance of excess air temperature between the city and its
surrounding space. In this object, we perform a numerical simulation
of the plume generated by the cars exhaust gases and show that these
gases form a screening effect above the urban city which cause the
heat island in the presence of wind flow. This study allows us: 1. To
understand the different mechanisms of interactions between these
phenomena.2. To consider appropriate technical solutions to mitigate
the effects of the heat island.
Abstract: Public space is essential to strengthen the social and
urban fabric and the social cohesion; there lies the importance of its
study. Hence, the aim of this paper is to analyze the quality of public
space in the XXI century in both quantitative and qualitative terms. In
this article, the concept of public space includes open spaces such as
parks, public squares and walking areas. To make this analysis, we
take Mexico City as the case study. It has a population of nearly 9
million inhabitants and is composed of sixteen boroughs. For this
analysis, we consider both existing public spaces and the government
intervention for building and improving new and existent public
spaces. Results show that on the one hand, quantitatively there is not
an equitable distribution of public spaces due to both the growth of
the city itself as well as due to the absence of political will to create
public spaces. Another factor is the evolution of this city, which has
been growing merely in a “patched pattern”, where public space has
played no role at all with a total absence of urban design. On the
other hand, qualitatively, even the boroughs with the most public
spaces have not shown interest in making these spaces qualitatively
inclusive and open to the general population aiming for integration.
Therefore, urban projects that privatize public space seem to be the
rule, rather than a rehabilitation effort of the existent public spaces.
Hence, state intervention should reinforce its role as an agent of
social change acting in benefit of the majority of the inhabitants with
the promotion of more inclusive public spaces.