Abstract: The synthesis of CuFe2O4 spinel powders by an
optimized combustion-like process followed by calcination is
described herein. The samples were characterized using X-ray
diffraction (XRD), differential thermal analysis (TG/DTA), scanning
electron microscopy (SEM), dilatometry and 4-probe DC methods.
Different glycine to nitrate (G/N) ratios of 1 (fuel-deficient), 1.48
(stoichiometric) and 2 (fuel-rich) were employed. Calcining the asprepared
powders at 800 and 1000°C for 5 hours showed that the G/N
ratio of 2 results in the formation of the desired copper spinel single
phase at both calcination temperatures. For G/N=1, formation of
CuFe2O4 takes place in three steps. First, iron and copper nitrates
decompose to iron oxide and pure copper. Then, copper transforms to
copper oxide and finally, copper and iron oxides react with each other
to form a copper ferrite spinel phase. The electrical conductivity and
the coefficient of thermal expansion of the sintered pelletized
samples were 2 S.cm-1 (800°C) and 11×10-6 °C-1 (25-800°C),
respectively.
Abstract: Residential block construction of big cities in China
began in the 1950s, and four models had far-reaching influence on
modern residential block in its development process, including unit
compound and residential district in 1950s to 1980s, and gated
community and open community in 1990s to now. Based on analysis
of the four models’ fabric, the article takes residential blocks in
Hangzhou west area as an example and carries on the studies from
urban structure level and block spacial level, mainly including urban
road network, land use, community function, road organization, public
space and building fabric. At last, the article puts forward “Semi-open
Sub-community” strategy to improve the current fabric.
Abstract: Sustainability is a very important and heavily
discussed subject, expanding through tourism as well. The study
proposition was to collect data and present it to the competent bodies
so they can mold their public policies to improve the conditions of
the site. It was hypothesized that the lack of data is currently
affecting the quality of life and the sustainable development of the
site and the tourism. The research was held in Mateiros, a city in the
state of Tocantins (TO)/Brasil near Palmas, its capital city. Because
of the concentration of tourists during the high season and several
tourist attractions being around, the research took place in Mateiros.
The methodological procedure had a script of theoretical construction
and investigation of the deductive scientific method parameters
through a case study in the Jalapão/TO/Brazil region, using it as a
tool for a questionnaire given to the competent bodies in an interview
system with the UN sustainability indexes as a base. In the three
sustainable development scope: environmental, social and economic,
the results indicated that the data presented by the interviewed were
scarce or nonexistent. It shows that more research is necessary,
providing the tools for the ones responsible to propose action plans to
improve the site, strengthening the tourism and making it even more
sustainable.
Abstract: The enormous amount of information stored on the
web increases from one day to the next, exposing the web currently
faced with the inevitable difficulties of research pertinent information
that users really want. The problem today is not limited to expanding
the size of the information highways, but to design a system for
intelligent search. The vast majority of this information is stored in
relational databases, which in turn represent a backend for managing
RDF data of the semantic web. This problem has motivated us to
write this paper in order to establish an effective approach to support
semantic transformation algorithm for SPARQL queries to SQL
queries, more precisely SPARQL SELECT queries; by adopting this
method, the relational database can be questioned easily with
SPARQL queries maintaining the same performance.
Abstract: Polyaniline is an indispensible component in lightemitting
devices (LEDs), televisions, cellular telephones, automotive,
corrosion-resistant coatings, actuators etc. The electrical conductivity
properties was found be increased by introduction of metal nano
particles. In the present study, an attempt has been made to utilize
platinum nano particles to achieve the improved electrical properties.
Polyaniline and Pt-polyaniline composite are synthesized by
electrochemical routes. X-ray diffractometer confirms the amorphous
nature of polyaniline. The Bragg’s diffraction peaks correspond to
platinum nanoparticles in Pt-polyaniline composite and
thermogravimetric analyzer indicates its decomposition at certain
temperature. The Scanning Electron Micrographs of colloidal
platinum nanoparticles were spherical, uniform shape in the
composite. The current-voltage (I-V) characteristics of the PANI and
composites were also studied which indicate a significant decreasing
resistivity than PANI-Platinum after introduction of pt nanoparticles
in the matrix of polyaniline (PANI).
Abstract: A Rice Sheller is used for obtaining polished white
rice from paddy. There are about 3000 Rice Shellers in Punjab and
50000 in India. During the process of shelling lot of dust is emitted
from different unit operations like paddy silo, paddy shaker, bucket
elevators, huskers, paddy separator etc. These dust emissions have
adverse effect on the health of the workers and the wear and tear of
the shelling machinery is fast. All the dust emissions spewing out of
these unit operations of a rice Sheller were contained by providing
suitable hoods and enclosures while ensuring their workability. These
were sucked by providing an induced draft fan followed by a high
efficiency cyclone separator that has got an overall dust collection
efficiency of more than 90%. This cyclone separator replaced two
cyclone separators and a filter bag house, which the Rice Sheller was
already having. The dust concentration in the stack after the
installation of cyclone separator is well within the stipulated
standards. Besides controlling pollution, there is improvement in the
quality of products like bran and the life of shelling machinery has
enhanced. The payback period of this technology is less than four
shelling months.
Abstract: The output error of the globoidal cam mechanism can
be considered as a relevant indicator of mechanism performance,
because it determines kinematic and dynamical behavior of
mechanical transmission. Based on the differential geometry and the
rigid body transformations, the mathematical model of surface
geometry of the globoidal cam is established. Then we present the
analytical expression of the output error (including the transmission
error and the displacement error along the output axis) by considering
different manufacture and assembly errors. The effects of the center
distance error, the perpendicular error between input and output axes
and the rotational angle error of the globoidal cam on the output error
are systematically analyzed. A globoidal cam mechanism which is
widely used in automatic tool changer of CNC machines is applied for
illustration. Our results show that the perpendicular error and the
rotational angle error have little effects on the transmission error but
have great effects on the displacement error along the output axis. This
study plays an important role in the design, manufacture and assembly
of the globoidal cam mechanism.
Abstract: Typical load-bearing biological materials like bone,
mineralized tendon and shell, are biocomposites made from both
organic (collagen) and inorganic (biomineral) materials. This
amazing class of materials with intrinsic internally designed
hierarchical structures show superior mechanical properties with
regard to their weak components from which they are formed.
Extensive investigations concentrating on static loading conditions
have been done to study the biological materials failure. However,
most of the damage and failure mechanisms in load-bearing
biological materials will occur whenever their structures are exposed
to dynamic loading conditions. The main question needed to be
answered here is: What is the relation between the layout and
architecture of the load-bearing biological materials and their
dynamic behavior? In this work, a staggered model has been
developed based on the structure of natural materials at nanoscale and
Finite Element Analysis (FEA) has been used to study the dynamic
behavior of the structure of load-bearing biological materials to
answer why the staggered arrangement has been selected by nature to
make the nanocomposite structure of most of the biological materials.
The results showed that the staggered structures will efficiently
attenuate the stress wave rather than the layered structure.
Furthermore, such staggered architecture is effectively in charge of
utilizing the capacity of the biostructure to resist both normal and
shear loads. In this work, the geometrical parameters of the model
like the thickness and aspect ratio of the mineral inclusions selected
from the typical range of the experimentally observed feature sizes
and layout dimensions of the biological materials such as bone and
mineralized tendon. Furthermore, the numerical results validated with
existing theoretical solutions. Findings of the present work emphasize
on the significant effects of dynamic behavior on the natural
evolution of load-bearing biological materials and can help scientists
to design bioinspired materials in the laboratories.
Abstract: A robust sequential nonparametric method is proposed
for adaptation to background noise parameters for real-time. The
distribution of background noise was modelled like to Huber
contamination mixture. The method is designed to operate as an
adaptation-unit, which is included inside a detection subsystem of an
integrated multichannel monitoring system. The proposed method
guarantees the given size of a nonasymptotic confidence set for noise
parameters. Properties of the suggested method are rigorously
proved. The proposed algorithm has been successfully tested in real
conditions of a functioning C-OTDR monitoring system, which was
designed to monitor railways.
Abstract: Ceramic Waste Aggregates (CWAs) were made from
electric porcelain insulator wastes supplied from an electric power
company, which were crushed and ground to fine aggregate sizes. In
this study, to develop the CWA mortar as an eco–efficient, ground
granulated blast–furnace slag (GGBS) as a Supplementary
Cementitious Material (SCM) was incorporated. The water–to–binder
ratio (W/B) of the CWA mortars was varied at 0.4, 0.5, and 0.6. The
cement of the CWA mortar was replaced by GGBS at 20 and 40% by
volume (at about 18 and 37% by weight). Mechanical properties of
compressive and splitting tensile strengths, and elastic modulus were
evaluated at the age of 7, 28, and 91 days. Moreover, the chloride
ingress test was carried out on the CWA mortars in a 5.0% NaCl
solution for 48 weeks. The chloride diffusion was assessed by using an
electron probe microanalysis (EPMA). To consider the relation of the
apparent chloride diffusion coefficient and the pore size, the pore size
distribution test was also performed using a mercury intrusion
porosimetry at the same time with the EPMA. The compressive
strength of the CWA mortars with the GGBS was higher than that
without the GGBS at the age of 28 and 91 days. The resistance to the
chloride ingress of the CWA mortar was effective in proportion to the
GGBS replacement level.
Abstract: The MEMS pressure sensor has been introduced and
presented in this paper. The types of pressure sensor and its theory of
operation are also included. The latest MEMS technology, the
fabrication processes of pressure sensor are explored and discussed.
Besides, various device applications of pressure sensor such as tire
pressure-monitoring system, diesel particulate filter and others are
explained. Due to further miniaturization of the device nowadays, the
pressure sensor with nanotechnology (NEMS) is also reviewed. The
NEMS pressure sensor is expected to have better performance as well
as lower in its cost. It has gained an excellent popularity in many
applications.
Abstract: This paper shows the general perceptions of Spanish
university stakeholders in relation to the university’s annual reports
and the adequacy and potential of intellectual capital reporting. To
this end, a questionnaire was designed and sent to every member of
the Social Councils of Spanish public universities. It was thought that
these participants would provide a good example of the attitude of
university stakeholders since they represent the different social
groups connected with universities. From the results of this study we
are in the position of confirming the need for universities to offer
information on intellectual capital in their accounting information
model.
Abstract: Transparent nickel doped cobalt sulfide was fabricated
on a SnO2:F electrode and tested as an efficient electrocatalyst and as
an alternative to the expensive platinum counter electrode. In order to
investigate how this electrode could affect the electrical
characteristics of a dye-sensitized solar cell, we manufactured cells
with the same TiO2 photoanode sensitized with dye (N719) and
employing the same quasi-solid electrolyte, altering only the counter
electrode used. The cells were electrically and electrochemically
characterized and it was observed that the ones with the Ni doped
CoS2 outperformed the efficiency of the cells with the Pt counter
electrode (3.76% and 3.44% respectively). Particularly, the higher
efficiency of the cells with the Ni doped CoS2 counter electrode (CE)
is mainly because of the enhanced photocurrent density which is
attributed to the enhanced electrocatalytic ability of the CE and the
low charge transfer resistance at the CE/electrolyte interface.
Abstract: The design of high pressure water jet based polishing
equipment and its fabrication conducted in this study is reported
herein, together with some preliminary test results for assessing its
applicability for HMA surface polishing. This study also provides
preliminary findings concerning the test variables, such as the
rotational speed, the water jet pressure, the abrasive agent used, and
the impact angel that were experimentally investigated in this study. The preliminary findings based on four trial tests (two on large
slab specimens and two on small size gyratory compacted
specimens), however, indicate that both friction and texture values
tend to increase with the polishing durations for two combinations of
pressure and rotation speed of the rotary deck. It seems that the more
polishing action the specimen is subjected to; the aggregate edges are
created such that the surface texture values are increased with the
accompanied increase in friction values. It may be of interest (but
which is outside the scope of this study) to investigate if the similar
trend exist for HMA prepared with aggregate source that is sand and
gravel.
Abstract: A bauxite ore can be utilized in Bayer Process, if the
mass ratio of Al2O3 to SiO2 is greater than 10. Otherwise, its FexOy
and SiO2 content should be removed. On the other hand, removal of
TiO2 from the bauxite ore would be beneficial because of both
lowering the red mud residue and obtaining a valuable raw material
containing TiO2 mineral. In this study, the low grade diasporic
bauxite ore of Yalvaç, Isparta, Turkey was roasted under reducing
atmosphere and subjected to magnetic separation. According to the
experimental results, 800°C for reduction temperature and 20000
Gauss of magnetic intensity were found to be the optimum
parameters for removal of iron oxide and rutile from the nonmagnetic
ore. On the other hand, 600°C and 5000 Gauss were
determined to be the optimum parameters for removal of silica from
the non-magnetic ore.
Abstract: In recent years, honeycomb fiber reinforced plastic
(FRP) sandwich panels have been increasingly used in various
industries. Low weight, low price and high mechanical strength are
the benefits of these structures. However, their mechanical properties
and behavior have not been fully explored. The objective of this
study is to conduct a combined numerical-statistical investigation of
honeycomb FRP sandwich beams subject to torsion load. In this
paper, the effect of geometric parameters of sandwich panel on
maximum shear strain in both face and core and angle of torsion in a
honeycomb FRP sandwich structures in torsion is investigated. The
effect of Parameters including core thickness, face skin thickness,
cell shape, cell size, and cell thickness on mechanical behavior of the
structure were numerically investigated. Main effects of factors were
considered in this paper and regression equations were derived.
Taguchi method was employed as experimental design and an
optimum parameter combination for the maximum structure stiffness
has been obtained. The results showed that cell size and face skin
thickness have the most significant impacts on torsion angle,
maximum shear strain in face and core.
Abstract: In this paper, we present a new segmentation approach
for liver lesions in regions of interest within MRI (Magnetic
Resonance Imaging). This approach, based on a two-cluster Fuzzy CMeans
methodology, considers the parameter variable compactness
to handle uncertainty. Fine boundaries are detected by a local
recursive merging of ambiguous pixels with a sequential forward
floating selection with Zernike moments. The method has been tested
on both synthetic and real images. When applied on synthetic images,
the proposed approach provides good performance, segmentations
obtained are accurate, their shape is consistent with the ground truth,
and the extracted information is reliable. The results obtained on MR
images confirm such observations. Our approach allows, even for
difficult cases of MR images, to extract a segmentation with good
performance in terms of accuracy and shape, which implies that the
geometry of the tumor is preserved for further clinical activities (such
as automatic extraction of pharmaco-kinetics properties, lesion
characterization, etc.).
Abstract: In this paper, the specific sound Transmission Loss
(TL) of the Laminated Composite Plate (LCP) with different material
properties in each layer is investigated. The numerical method to
obtain the TL of the LCP is proposed by using elastic plate theory. The
transfer matrix approach is novelty presented for computational
efficiency in solving the numerous layers of dynamic stiffness matrix
(D-matrix) of the LCP. Besides the numerical simulations for
calculating the TL of the LCP, the material properties inverse method
is presented for the design of a laminated composite plate analogous to
a metallic plate with a specified TL. As a result, it demonstrates that
the proposed computational algorithm exhibits high efficiency with a
small number of iterations for achieving the goal. This method can be
effectively employed to design and develop tailor-made materials for
various applications.
Abstract: RF magnetron sputtering is used on the ceramic targets,
each of which contains zinc oxide (ZnO), zinc oxide doped with
aluminum (AZO) and zinc oxide doped with gallium (GZO). The XRD
analysis showed a preferred orientation along the (002) plane for ZnO,
AZO, and GZO films. The AZO film had the best electrical properties;
it had the lowest resistivity of 6.6 × 10-4 cm, the best sheet resistance of
2.2 × 10-1 Ω/square, and the highest carrier concentration of 4.3 × 1020
cm-3, as compared to the ZnO and GZO films.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.