Abstract: Zinc borates are used as a multi-functional flame
retardant additive for its high dehydration temperature. In this study,
the method of ultrasonic mixing was used in the synthesis of zinc
borates. The reactants of zinc oxide (ZnO) and boric acid (H3BO3)
were used at the constant reaction parameters of 90°C reaction
temperature and 55 min of reaction time. Several molar ratios of
ZnO:H3BO3 (1:1, 1:2, 1:3, 1:4 and 1:5) were conducted for the
determination of the optimum reaction ratio. Prior to synthesis the
characterization of the synthesized zinc borates were made by X-Ray
Diffraction (XRD) and Fourier Transform Infrared Spectroscopy
(FT-IR). From the results Zinc Oxide Borate Hydrate
[Zn3B6O12.3.5H2O], were synthesized optimum at the molar ratio of
1:3, with a reaction efficiency of 95.2%.
Abstract: In this paper, we introduce a flexible box erecting
machine (BEM) that swiftly and automatically transforms cardboard
into a three dimensional box. Recently, the parcel service and
home-shopping industries have grown rapidly, and there is an
increasing need for various box types to ship various products.
However, workers cannot fold thousands of boxes manually in a day.
As such, automatic BEMs are garnering greater attention. This study
takes equipment operation into consideration as well as mechanical
improvements in order to design a BEM that is able to outperform its
conventional counterparts. We analyzed six dispatching rules – First In
First Out (FIFO), Shortest Processing Time (SPT), Earliest Due Date
(EDD), Setup Avoidance, EDD + SPT, and EDD + Setup Avoidance –
to determine which one was most suitable for BEM operation.
Consequently, SPT and Setup Avoidance were found to be the most
critical rules, followed by EDD + Setup Avoidance, EDD + SPT,
EDD, and FIFO. This hierarchy was valid for both our conventional
BEM and our new flexible BEM from the viewpoint of processing
time. We believe that this research can contribute to flexible BEM
management, which has the potential to increase productivity and
convenience.
Abstract: Fresh concrete has one of dynamic properties known
as slump. Slump of concrete is design to compatible with placing
method. Due to hydration reaction of cement, the slump of concrete
is loss through time. Therefore, delayed concrete probably get reject
because slump is unacceptable. In order to recover the slump of
delayed concrete the second dose of superplasticizer (naphthalene
based type F) is added into the system, the slump recovery can be
done as long as the concrete is not setting. By adding superplasticizer
as solution for recover unusable slump loss concrete may affects
other concrete properties. Therefore, this paper was observed setting
times and compressive strength of concrete after being re-dose with
chemical admixture type F (superplasticizer, naphthalene based) for
slump recovery. The concrete used in this study was fly ash concrete
with fly ash replacement of 0%, 30% and 50% respectively. Concrete
mix designed for test specimen was prepared with paste content (ratio
of volume of cement to volume of void in the aggregate) of 1.2 and
1.3, water-to-binder ratio (w/b) range of 0.3 to 0.58, initial dose of
superplasticizer (SP) range from 0.5 to 1.6%. The setting times of
concrete were tested both before and after re-dosed with different
amount of second dose and time of dosing. The research was
concluded that addition of second dose of superplasticizer would
increase both initial and final setting times accordingly to dosage of
addition. As for fly ash concrete, the prolongation effect was higher
as the replacement of fly ash increase. The prolongation effect can
reach up to maximum about 4 hours. In case of compressive strength,
the re-dosed concrete has strength fluctuation within acceptable range
of ±10%.
Abstract: The change of conditions for production companies in
high-wage countries is characterized by the globalization of
competition and the transition of a supplier´s to a buyer´s market. The
companies need to face the challenges of reacting flexibly to these
changes. Due to the significant and increasing degree of automation,
assembly has become the most expensive production process.
Regarding the reduction of production cost, assembly consequently
offers a considerable rationalizing potential. Therefore, an
aerodynamic feeding system has been developed at the Institute of
Production Systems and Logistics (IFA), Leibniz Universitaet
Hannover. This system has been enabled to adjust itself by using a
genetic algorithm. The longer this genetic algorithm is executed the
better is the feeding quality. In this paper, the relation between the
system´s setting time and the feeding quality is observed and a
function which enables the user to achieve the minimum of the total
feeding time is presented.
Abstract: This paper introduces a signal monitoring program
developed with a view to helping electrical engineering students get
familiar with sensors with digital output. Because the output of digital
sensors cannot be simply monitored by a measuring instrument such as
an oscilloscope, students tend to have a hard time dealing with digital
sensors. The monitoring program runs on a PC and communicates with
an MCU that reads the output of digital sensors via an asynchronous
communication interface. Receiving the sensor data from the MCU,
the monitoring program shows time and/or frequency domain plots of
the data in real time. In addition, the monitoring program provides a
serial terminal that enables the user to exchange text information with
the MCU while the received data is plotted. The user can easily
observe the output of digital sensors and configure the digital sensors
in real time, which helps students who do not have enough experiences
with digital sensors. Though the monitoring program was programmed
in the Matlab programming language, it runs without the Matlab since
it was compiled as a standalone executable.
Abstract: Multiprocessor task scheduling problem for dependent
and independent tasks is computationally complex problem. Many
methods are proposed to achieve optimal running time. As the
multiprocessor task scheduling is NP hard in nature, therefore, many
heuristics are proposed which have improved the makespan of the
problem. But due to problem specific nature, the heuristic method
which provide best results for one problem, might not provide good
results for another problem. So, Simulated Annealing which is meta
heuristic approach is considered. It can be applied on all types of
problems. However, due to many runs, meta heuristic approach takes
large computation time. Hence, the hybrid approach is proposed by
combining the Duplication Scheduling Heuristic and Simulated
Annealing (SA) and the makespan results of Simple Simulated
Annealing and Hybrid approach are analyzed.
Abstract: This paper concentrates on the sustainable traditional
architecture and urban planning in hot-humid regions of Iran. In a
vast country such as Iran with different climatic zones traditional
builders have presented series of logical solutions for human comfort.
The aim of this paper is to demonstrate traditional architecture in hothumid
climate of Iran as a sample of sustainable architecture. Iranian
traditional architecture has been able to response to environmental
problems for a long period of time. Its features are based on climatic
factors, local construction materials of hot-humid regions and culture.
This paper concludes that Iranian traditional architecture can be
addressed as a sustainable architecture.
Abstract: The plastic industry plays very important role in the
economy of any country. It is generally among the leading share of
the economy of the country. Since metals and their alloys are very
rarely available on the earth. Therefore, to produce plastic products
and components, which finds application in many industrial as well
as household consumer products is beneficial. Since 50% plastic
products are manufactured by injection moulding process. For
production of better quality product, we have to control quality
characteristics and performance of the product. The process
parameters plays a significant role in production of plastic, hence the
control of process parameter is essential. In this paper the effect of
the parameters selection on injection moulding process has been
described. It is to define suitable parameters in producing plastic
product. Selecting the process parameter by trial and error is neither
desirable nor acceptable, as it is often tends to increase the cost and
time. Hence, optimization of processing parameter of injection
moulding process is essential. The experiments were designed with
Taguchi’s orthogonal array to achieve the result with least number of
experiments. Plastic material polypropylene is studied. Tensile
strength test of material is done on universal testing machine, which
is produced by injection moulding machine. By using Taguchi
technique with the help of MiniTab-14 software the best value of
injection pressure, melt temperature, packing pressure and packing
time is obtained. We found that process parameter packing pressure
contribute more in production of good tensile plastic product.
Abstract: The aim of sustainable architecture is to design
buildings with the least adverse effects on the environment and
provide better conditions for people. What building forms make the
best use of land? This question was addressed in the late 1960s at the
center of Land Use and Built Form Studies in Cambridge. This led to
a number of influential papers which had a great influence on the
practice of urban design. This paper concentrates on the results of
sustainability caused by climatic conditions in Iranian traditional
architecture in hot-arid regions. As people spent a significant amount
of their time in houses, it was very important to have such houses to
fulfill their needs physically and spiritually as well as satisfying their
cultural and religious aspects of their lifestyles. In a vast country such
as Iran with different climatic zones, traditional builders have
presented series of logical solutions for human comfort. These
solutions have been able to response to the environmental problems
for a long period of time. As a result, by considering the experience
in traditional architecture of hot–arid climate in Iran, it is possible to
attain sustainable architecture.
Abstract: Synchrophasor technology is fast being deployed in
electric power grids all over the world and is fast changing the way
the grids are managed. This trend is to continue until the entire
power grids are fully connected so they can be monitored and
controlled in real-time. Much achievement has been made in the
synchrophasor technology development and deployment, and there
are still much more to be achieved. For instance, real-time power
grid control and protection potentials of synchrophasor are yet to be
explored. It is of necessity that researchers keep in view the various
challenges that still need to be overcome in expanding the frontiers
of synchrophasor technology. This paper outlines the major
challenges that should be dealt with in order to achieve the goal of
total power grid visualization, monitoring, and control using
synchrophasor technology.
Abstract: Heat treatable aluminum alloys such as 7075 and
7055, because of high strength and low density, are used widely in
aircraft industry. For best mechanical properties, T6 heat treatment
has recommended for this regards, but this temper treatment is
sensitive to corrosion induced and Stress Corrosion Cracking (SCC)
damage. For improving this property, the over-aging treatment (T7)
applies to this alloy, but it decreases the mechanical properties up to
30 percent. Hence, to increase the mechanical properties, without any
remarkable decrease in SCC resistant, Retrogression and Re-Aging
(RRA) heat treatment is used. This treatment performs in a relatively
short time. In this paper, the RRA heat treatment was applied to 7055
aluminum alloy and then effect of RRA time on the mechanical
properties of 7055 has been investigated. The results show that the
40-minute time is suitable time for retrogression of 7055 aluminum
alloy and ultimate strength increases up to 625MPa.
Abstract: In this paper genetic based test data compression is
targeted for improving the compression ratio and for reducing the
computation time. The genetic algorithm is based on extended pattern
run-length coding. The test set contains a large number of X value
that can be effectively exploited to improve the test data
compression. In this coding method, a reference pattern is set and its
compatibility is checked. For this process, a genetic algorithm is
proposed to reduce the computation time of encoding algorithm. This
coding technique encodes the 2n compatible pattern or the inversely
compatible pattern into a single test data segment or multiple test data
segment. The experimental result shows that the compression ratio
and computation time is reduced.
Abstract: This research tested the performance of alternative
warehouse designs concerning the picking process. The chosen
performance measures were Travel Distance and Total Fulfilment
Time. An explanatory case study was built up around a model
implemented with SIMUL8. Hypotheses were set by selecting
outcomes from the literature survey matching popular empirical
findings. 17.4% reductions were found for Total Fulfilment Time and
Resource Utilisation. The latter was then used as a proxy for
operational efficiency. Literal replication of theoretical data-patterns
was considered as an internal validity sign. Assessing the estimated
changes benefits ahead of implementation was found to be a
contribution to practice.
Abstract: Detecting changes in multiple images of the same
scene has recently seen increased interest due to the many
contemporary applications including smart security systems, smart
homes, remote sensing, surveillance, medical diagnosis, weather
forecasting, speed and distance measurement, post-disaster forensics
and much more. These applications differ in the scale, nature, and
speed of change. This paper presents an application of image
processing techniques to implement a real-time change detection
system. Change is identified by comparing the RGB representation of
two consecutive frames captured in real-time. The detection threshold
can be controlled to account for various luminance levels. The
comparison result is passed through a filter before decision making to
reduce false positives, especially at lower luminance conditions. The
system is implemented with a MATLAB Graphical User interface
with several controls to manage its operation and performance.
Abstract: In this article, we used the residual correction method
to deal with transient thermoelastic problems with a hollow spherical
region when the continuum medium possesses spherically isotropic
thermoelastic properties. Based on linear thermoelastic theory, the
equations of hyperbolic heat conduction and thermoelastic motion
were combined to establish the thermoelastic dynamic model with
consideration of the deformation acceleration effect and non-Fourier
effect under the condition of transient thermal shock. The approximate
solutions of temperature and displacement distributions are obtained
using the residual correction method based on the maximum principle
in combination with the finite difference method, making it easier and
faster to obtain upper and lower approximations of exact solutions.
The proposed method is found to be an effective numerical method
with satisfactory accuracy. Moreover, the result shows that the effect
of transient thermal shock induced by deformation acceleration is
enhanced by non-Fourier heat conduction with increased peak stress.
The influence on the stress increases with the thermal relaxation time.
Abstract: Countryside has been generally recognized and
regarded as a characteristic symbol which presents in human memory
for a long time. As a result of the change of times, because of it is
failure to meet the growing needs of the growing life and mental
decline, the vast rural area began to decline. But their history feature
image which accumulated by the ancient tradition provides people
with the origins of existence on the spiritual level, such as "identity"
and "belonging", makes people closer to the others in the spiritual and
psychological aspects of a common experience about the past, thus the
sense of a lack of culture caused by the losing of memory symbols is
weakened. So, in the modernization process, how to repair its vitality
and transform and planning it in a sustainable way has become a hot
topics in architectural and urban planning. This paper aims to break
the constraints of disciplines, from the perspective of interdiscipline,
using the research methods of systems science to analyze and discuss
the theories and methods of rural form factors, which based on the
viewpoint of memory in psychology. So we can find a right way to
transform the Rural to give full play to the role of the countryside in
the actual use and the shape of history spirits.
Abstract: In this paper, we propose two algorithms to optimally
solve makespan and total completion time scheduling problems with
learning effect and job dependent delivery times in a single machine
environment. The delivery time is the extra time to eliminate adverse
effect between the main processing and delivery to the customer. In
this paper, we introduce the job dependent delivery times for some
single machine scheduling problems with position dependent learning
effect, which are makespan are total completion. The results with
respect to two algorithms proposed for solving of the each problem
are compared with LINGO solutions for 50-jobs, 100-jobs and 150-
jobs problems. The proposed algorithms can find the same results in
shorter time.
Abstract: High moisture content in fruits generates post-harvest
problems such as mechanical, biochemical, microbial and physical
losses. Dehydration, which is based on the reduction of water activity
of the fruit, is a common option for overcoming such losses.
However, regular hot air drying could affect negatively the quality
properties of the fruit due to the long residence time at high
temperature. Power ultrasound (US) application during the
convective drying has been used as a novel method able to enhance
drying rate and, consequently, to decrease drying time. In the present
study, a new approach was tested to evaluate the effect of US on the
drying time, the final antioxidant activity (AA) and the total
polyphenol content (TPC) of banana slices (BS), mango slices (MS)
and guava slices (GS). There were also studied the drying kinetics
with nine different models from which water effective diffusivities
(Deff) (with or without shrinkage corrections) were calculated.
Compared with the corresponding control tests, US assisted drying
for fruit slices showed reductions in drying time between 16.23 and
30.19%, 11.34 and 32.73%, and 19.25 and 47.51% for the MS, BS
and GS respectively. Considering shrinkage effects, Deff calculated
values ranged from 1.67*10-10 to 3.18*10-10 m2/s, 3.96*10-10 and
5.57*10-10 m2/s and 4.61*10-10 to 8.16*10-10 m2/s for the BS, MS and
GS samples respectively. Reductions of TPC and AA (as DPPH)
were observed compared with the original content in fresh fruit data
in all kinds of drying assays.
Abstract: Biomass treatment through densification is very suitable and helpful technology before its effective energy recovery. Densification process of biomass is significantly influenced by various technological and material variables, which are ultimately reflected on the final solid biofuels quality. The paper deals with the experimental research of the relationship between technological and material variables during densification of fast-growing trees, roundly fast-growing willows. The main goal of presented experimental research is to determine the relationship between compression pressure and raw material particle size from a final briquettes density point of view. Experimental research was realized by single-axis densification. The impact of particle size with interaction of compression pressure and stabilization time on the quality properties of briquettes was determined. These variables interaction affects the final solid biofuels (briquettes) quality. From briquettes production point of view and from densification machines constructions point of view is very important to know about mutual interaction of these variables on final briquettes quality. The experimental findings presented here are showing the importance of mentioned variables during the densification process.
Abstract: The practical efficient approach is suggested to estimate the high-speed objects instant bounds in C-OTDR monitoring systems. In case of super-dynamic objects (trains, cars) is difficult to obtain the adequate estimate of the instantaneous object localization because of estimation lag. In other words, reliable estimation coordinates of monitored object requires taking some time for data observation collection by means of C-OTDR system, and only if the required sample volume will be collected the final decision could be issued. But it is contrary to requirements of many real applications. For example, in rail traffic management systems we need to get data of the dynamic objects localization in real time. The way to solve this problem is to use the set of statistical independent parameters of C-OTDR signals for obtaining the most reliable solution in real time. The parameters of this type we can call as «signaling parameters» (SP). There are several the SP’s which carry information about dynamic objects instant localization for each of COTDR channels. The problem is that some of these parameters are very sensitive to dynamics of seismoacoustic emission sources, but are non-stable. On the other hand, in case the SP is very stable it becomes insensitive as rule. This report contains describing of the method for SP’s co-processing which is designed to get the most effective dynamic objects localization estimates in the C-OTDR monitoring system framework.