Abstract: This paper presents a new compact analytical model of
the gate leakage current in high-k based nano scale MOSFET by
assuming a two-step inelastic trap-assisted tunneling (ITAT) process
as the conduction mechanism. This model is based on an inelastic
trap-assisted tunneling (ITAT) mechanism combined with a semiempirical
gate leakage current formulation in the BSIM 4 model. The
gate tunneling currents have been calculated as a function of gate
voltage for different gate dielectrics structures such as HfO2, Al2O3
and Si3N4 with EOT (equivalent oxide thickness) of 1.0 nm. The
proposed model is compared and contrasted with santaurus
simulation results to verify the accuracy of the model and excellent
agreement is found between the analytical and simulated data. It is
observed that proposed analytical model is suitable for different highk
gate dielectrics simply by adjusting two fitting parameters. It was
also shown that gate leakages reduced with the introduction of high-k
gate dielectric in place of SiO2.
Abstract: In this paper a study on the vibration of thin
cylindrical shells with ring supports and made of functionally
graded materials (FGMs) composed of stainless steel and
nickel is presented. Material properties vary along the
thickness direction of the shell according to volume fraction
power law. The cylindrical shells have ring supports which are
arbitrarily placed along the shell and impose zero lateral
deflections. The study is carried out based on third order shear
deformation shell theory (T.S.D.T). The analysis is carried out
using Hamilton-s principle. The governing equations of motion of
FGM cylindrical shells are derived based on shear deformation
theory. Results are presented on the frequency characteristics,
influence of ring support position and the influence of boundary
conditions. The present analysis is validated by comparing results
with those available in the literature.
Abstract: In this paper a novel ultra-wideband (UWB) slot antenna with band notch characteristics for world interoperability for microwave access (WiMAX) is proposed. The designed antenna consists of a rectangular radiating patch and a ground plane with tapered shape slot. To realize a notch band, a curved parasitic element has been etched out along with the radiating patch. It is observed that by adjusting the length, thickness and position of the parasitic element, the proposed antenna can achieved an impedance bandwidth of 8.01GHz (2.84 to 10.85GHz) with a notched band of 3.28-3.85GHz. Compared to the recently reported band notch antennas, the proposed antenna has a simple configuration to realize band notch characteristics in order to mitigate the potential interference between WiMAX and UWB system. Furthermore, a stable radiation pattern and moderate gain except at the notched band makes the proposed antenna suitable for various UWB applications.
Abstract: The orthogonal processes to shape the triangle steel plate into a equilateral vertical steel are examined by an incremental elasto-plastic finite-element method based on an updated Lagrangian formulation. The highly non-linear problems due to the geometric changes, the inelastic constitutive behavior and the boundary conditions varied with deformation are taken into account in an incremental manner. On the contact boundary, a modified Coulomb friction mode is specially considered. A weighting factor r-minimum is employed to limit the step size of loading increment to linear relation. In particular, selective reduced integration was adopted to formulate the stiffness matrix. The simulated geometries of verticality could clearly demonstrate the vertical processes until unloading. A series of experiments and simulations were performed to validate the formulation in the theory, leading to the development of the computer codes. The whole deformation history and the distribution of stress, strain and thickness during the forming process were obtained by carefully considering the moving boundary condition in the finite-element method. Therefore, this modeling can be used for judging whether a equilateral vertical steel can be shaped successfully. The present work may be expected to improve the understanding of the formation of the equilateral vertical steel.
Abstract: Design of experiments made for correlated the hormonal activity of steroids and their effect on the vaginal structure properties. Vaginal wall consists of distinct layers of cells which strongly differ regarding growth in answer to steroid hormones. The presence study carried out for functional evaluation and sustained replacement effect of the reproductive hormones on the vaginal morphometry in the rabbit. Rabbits were maintained control (Co) or ovariectomized (Ovz) and continuously treated with estradiol (Ovz E) and estradiol mixture with testosterone (Ovz ET). Relative to control rabbits with the distinct tissue distribution pattern, ovariectomized animals displayed declined epithelial thickness and atrophy of the muscularis layer that cause the vaginal wall thinning. Estradiol treatment of Orz rabbits inverted these changes to status of the preovariectomy. Histometric measurements in Ovz ET group completely including of thickness of the epithelial and muscular layers was greater in comparison to that of control animals.
Abstract: To derive the fractional flow equation oil
displacement will be assumed to take place under the so-called
diffusive flow condition. The constraints are that fluid saturations at
any point in the linear displacement path are uniformly distributed
with respect to thickness; this allows the displacement to be described
mathematically in one dimension. The simultaneous flow of oil and
water can be modeled using thickness averaged relative permeability,
along the centerline of the reservoir. The condition for fluid potential
equilibrium is simply that of hydrostatic equilibrium for which the
saturation distribution can be determined as a function of capillary
pressure and therefore, height. That is the fluids are distributed in
accordance with capillary-gravity equilibrium.
This paper focused on the fraction flow of water versus
cumulative oil recoveries using Buckley Leverett method. Several
field cases have been developed to aid in analysis. Producing watercut
(at surface conditions) will be compared with the cumulative oil
recovery at breakthrough for the flowing fluid.
Abstract: This paper presents the experimental results on space charge distribution in cross-linked polyethylene (XLPE) insulating material for 22 kV power distribution system cable by using pulse electroacoustic measurement technique (PEA). Numbers of XLPE insulating material ribbon having thickness 60 μm taken from unused 22 kV high voltage cable were used as specimen in this study. DC electric field stress was applied to test specimen at room temperature (25°C). Four levels of electric field stress, 25 kV/mm, 50 kV/mm, 75 kV/mm and 100 kV/mm, were used. In order to investigate space charge distribution characteristic, space charge distribution characteristics were measured after applying electric field stress 15 min, 30 min and 60 min, respectively. The results show that applied time and magnitude of dc electric field stress play an important role to the formation of space charge.
Abstract: The steady coupled dissipative layers, called
Marangoni mixed convection boundary layers, in the presence of a
magnetic field and solute concentration that are formed along the
surface of two immiscible fluids with uniform suction or injection
effects is examined. The similarity boundary layer equations are
solved numerically using the Runge-Kutta Fehlberg with shooting
technique. The Marangoni, buoyancy and external pressure gradient
effects that are generated in mixed convection boundary layer flow
are assessed. The velocity, temperature and concentration boundary
layers thickness decrease with the increase of the magnetic field
strength and the injection to suction. For buoyancy-opposed flow, the
Marangoni mixed convection parameter enhances the velocity
boundary layer but decreases the temperature and concentration
boundary layers. However, for the buoyancy-assisted flow, the
Marangoni mixed convection parameter decelerates the velocity but
increases the temperature and concentration boundary layers.
Abstract: In the present work, study of the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. Material properties are graded in the thickness direction of the shell according to volume fraction power law distribution. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of boundary conditions on the natural frequencies of the FG cylindrical shell. The study is carried out using third order shear deformation shell theory. The governing equations of motion of FG cylindrical shells are derived based on shear deformation theory. Results are presented on the frequency characteristics, influence of constituent volume fractions and the effects of free-free boundary conditions.
Abstract: Non-isothermal stagnation-point flow with consideration of thermal radiation is studied numerically. A set of partial differential equations that governing the fluid flow and energy is converted into a set of ordinary differential equations which is solved by Runge-Kutta method with shooting algorithm. Dimensionless wall temperature gradient and temperature boundary layer thickness for different combinaton of values of Prandtl number Pr and radiation parameter NR are presented graphically. Analyses of results show that the presence of thermal radiation in the stagnation-point flow is to increase the temperature boundary layer thickness and decrease the dimensionless wall temperature gradient.
Abstract: This paper aims to present the design, fabrication and test of a novel piezoelectric actuated, check-valves embedded micropump having the advantages of miniature size, light weight and low power consumption. This device is designed to pump gases and liquids with the capability of performing the self-priming and bubble-tolerant work mode by maximizing the stroke volume of the membrane as well as the compression ratio via minimization of the dead volume of the micropump chamber and channel. By experiment apparatus setup, we can get the real-time values of the flow rate of micropump, the displacement of the piezoelectric actuator and the deformation of the check valve, simultaneously. The micropump with check valve 0.4 mm in thickness obtained higher output performance under the sinusoidal waveform of 120 Vpp. The micropump achieved the maximum pumping rates of 42.2 ml/min and back pressure of 14.0 kPa at the corresponding frequency of 28 and 20 Hz. The presented micropump is able to pump gases with a pumping rate of 196 ml/min at operating frequencies of 280 Hz under the sinusoidal waveform of 120 Vpp.
Abstract: The characterization and modeling of the dynamic
behavior of many built-up structures under vibration conditions is still
a subject of current research. The present study emphasizes the
theoretical investigation of slip damping in layered and jointed
welded cantilever structures using finite element approach.
Application of finite element method in damping analysis is relatively
recent, as such, some problems particularly slip damping analysis has
not received enough attention. To validate the finite element model
developed, experiments have been conducted on a number of mild
steel specimens under different initial conditions of vibration. Finite
element model developed affirms that the damping capacity of such
structures is influenced by a number of vital parameters such as;
pressure distribution, kinematic coefficient of friction and micro-slip
at the interfaces, amplitude, frequency of vibration, length and
thickness of the specimen. Finite element model developed can be
utilized effectively in the design of machine tools, automobiles,
aerodynamic and space structures, frames and machine members for
enhancing their damping capacity.
Abstract: This article demonstrated development of
controlled release system of an NSAID drug, Diclofenac
sodium employing different ratios of Ethyl cellulose.
Diclofenac sodium and ethyl cellulose in different proportions
were processed by microencapsulation based on phase
separation technique to formulate microcapsules. The
prepared microcapsules were then compressed into tablets to
obtain controlled release oral formulations. In-vitro evaluation
was performed by dissolution test of each preparation was
conducted in 900 ml of phosphate buffer solution of pH 7.2
maintained at 37 ± 0.5 °C and stirred at 50 rpm. At predetermined
time intervals (0, 0.5, 1.0, 1.5, 2, 3, 4, 6, 8, 10, 12,
16, 20 and 24 hrs). The drug concentration in the collected
samples was determined by UV spectrophotometer at 276 nm.
The physical characteristics of diclofenac sodium
microcapsules were according to accepted range. These were
off-white, free flowing and spherical in shape. The release
profile of diclofenac sodium from microcapsules was found to
be directly proportional to the proportion of ethylcellulose and
coat thickness. The in-vitro release pattern showed that with
ratio of 1:1 and 1:2 (drug: polymer), the percentage release of
drug at first hour was 16.91 and 11.52 %, respectively as
compared to 1:3 which is only 6.87 % with in this time. The
release mechanism followed higuchi model for its release
pattern. Tablet Formulation (F2) of present study was found
comparable in release profile the marketed brand Phlogin-SR,
microcapsules showed an extended release beyond 24 h.
Further, a good correlation was found between drug release
and proportion of ethylcellulose in the microcapsules.
Microencapsulation based on coacervation found as good
technique to control release of diclofenac sodium for making
the controlled release formulations.
Abstract: The paper describes a knowledge based system for
analysis of microscopic wear particles. Wear particles contained in
lubricating oil carry important information concerning machine
condition, in particular the state of wear. Experts (Tribologists) in the
field extract this information to monitor the operation of the machine
and ensure safety, efficiency, quality, productivity, and economy of
operation. This procedure is not always objective and it can also be
expensive. The aim is to classify these particles according to their
morphological attributes of size, shape, edge detail, thickness ratio,
color, and texture, and by using this classification thereby predict
wear failure modes in engines and other machinery. The attribute
knowledge links human expertise to the devised Knowledge Based
Wear Particle Analysis System (KBWPAS). The system provides an
automated and systematic approach to wear particle identification
which is linked directly to wear processes and modes that occur in
machinery. This brings consistency in wear judgment prediction
which leads to standardization and also less dependence on
Tribologists.
Abstract: The study aimed to investigate characteristics of
vegetative tissue for taxonomic purpose and possibly trend of waste
application in industry. Stems and branches of 15 species in Solanum
found in Thailand were prepared for fiber and examined by light
microscopy. Microstructural characteristic data of fiber i.e. fiber
length and width, fiber lumen diameter and fiber cell wall thickness
were recorded. The longest average fiber cell length (>3.9 mm.) were
obtained in S. lycopersicum L. and S. tuberosum L. Fiber cells from
S. lycopersicum also revealed the widest average diameter of whole
cell and its lumen at >45.5 μm and >29 μm respectively. However
fiber cells with thickest wall of > 9.6 μm were belonged to the
ornamental tree species, S. wrightii Benth. The results showed that
the slenderness ratio, Runkel ratio, and flexibility coefficient, with
potentially suitable for feedstock in paper industry fell in 4 exotic
species, i.e. Solanumamericanum L., S. lycopersicum, S.
seaforthianum Andr., and S. tuberosum L
Abstract: Psoriasis is a chronic inflammatory skin condition
which affects 2-3% of population around the world. Psoriasis Area
and Severity Index (PASI) is a gold standard to assess psoriasis
severity as well as the treatment efficacy. Although a gold standard,
PASI is rarely used because it is tedious and complex. In practice,
PASI score is determined subjectively by dermatologists, therefore
inter and intra variations of assessment are possible to happen even
among expert dermatologists. This research develops an algorithm to
assess psoriasis lesion for PASI scoring objectively. Focus of this
research is thickness assessment as one of PASI four parameters
beside area, erythema and scaliness. Psoriasis lesion thickness is
measured by averaging the total elevation from lesion base to lesion
surface. Thickness values of 122 3D images taken from 39 patients
are grouped into 4 PASI thickness score using K-means clustering.
Validation on lesion base construction is performed using twelve
body curvature models and show good result with coefficient of
determinant (R2) is equal to 1.
Abstract: A triangular fin with variable fin base thickness is analyzed and optimized using a two-dimensional analytical method. The influence of fin base height and fin base thickness on the temperature in the fin is listed. For the fixed fin volumes, the maximum heat loss, the corresponding optimum fin effectiveness, fin base height and fin tip length as a function of the fin base thickness, convection characteristic number and dimensionless fin volume are represented. One of the results shows that the optimum heat loss increases whereas the corresponding optimum fin effectiveness decreases with the increase of fin volume.
Abstract: Ice cover County has a significant impact on rivers as it affects with the ice melting capacity which results in flooding, restrict navigation, modify the ecosystem and microclimate. River ices are made up of different ice types with varying ice thickness, so surveillance of river ice plays an important role. River ice types are captured using infrared imaging camera which captures the images even during the night times. In this paper the river ice infrared texture images are analysed using first-order statistical methods and secondorder statistical methods. The second order statistical methods considered are spatial gray level dependence method, gray level run length method and gray level difference method. The performance of the feature extraction methods are evaluated by using Probabilistic Neural Network classifier and it is found that the first-order statistical method and second-order statistical method yields low accuracy. So the features extracted from the first-order statistical method and second-order statistical method are combined and it is observed that the result of these combined features (First order statistical method + gray level run length method) provides higher accuracy when compared with the features from the first-order statistical method and second-order statistical method alone.
Abstract: The Pads have unique values of thermophysical
properties (THP) having important contribution over heat transfer
into the PCB structure.
Materials with high thermal diffusivity (TD) rapidly adjust their
temperature to that of their surroundings, because the HT is quick in
compare to their volumetric heat capacity (VHC).
In the paper is presenting the diffusivity tests (ASTM E1461 flash
method) for PCBs with different core materials. In the experiments,
the multilayer structure of PCBA was taken into consideration, an
equivalent property referring to each of experimental structure be
practically measured.
Concerning to entire structure, the THP emphasize the major
contribution of substrate in establishing of reflow soldering process
(RSP) heat transfer necessities. This conclusion offer practical
solution for heat transfer time constant calculation as function of
thickness and substrate material diffusivity with an acceptable error
estimation.
Abstract: Combined conduction-free convection heat transfer in
vertical eccentric annuli is numerically investigated using a finitedifference
technique. Numerical results, representing the heat transfer
parameters such as annulus walls temperature, heat flux, and heat
absorbed in the developing region of the annulus, are presented for a
Newtonian fluid of Prandtl number 0.7, fluid-annulus radius ratio 0.5,
solid-fluid thermal conductivity ratio 10, inner and outer wall
dimensionless thicknesses 0.1 and 0.2, respectively, and
dimensionless eccentricities 0.1, 0.3, 0.5, and 0.7. The annulus walls
are subjected to thermal boundary conditions, which are obtained by
heating one wall isothermally whereas keeping the other wall at inlet
fluid temperature. In the present paper, the annulus heights required
to achieve thermal full development for prescribed eccentricities are
obtained. Furthermore, the variation in the height of thermal full
development as function of the geometrical parameter, i.e.,
eccentricity is also investigated.