Abstract: Dehydration process was carried out for tomato slices of var. Avinash after giving different pre-treatments such as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl). Untreated samples served as control. Solar drier and continuous conveyor (tunnel) drier were used for dehydration. Quality characteristics of tomato slices viz. moisture content, sugar, titratable acidity, lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning as affected by dehydration process were studied. Storage study was also carried out for a period of six months for tomato powder packed into different types of packaging materials viz. metalized polyester (MP) film and low density poly ethylene (LDPE). Changes in lycopene content and non-enzymatic browning (NEB) were estimated during storage at room temperature. Pretreatment of 5 mm thickness of tomato slices with calcium chloride in combination with potassium metabisulphite and drying using a tunnel drier with subsequent storage of product in metalized polyester bags was selected as the best process.
Abstract: The static stability analysis of stiffened functionally
graded cylindrical shells by isotropic rings and stringers subjected to
axial compression is presented in this paper. The Young's modulus of
the shell is taken to be function of the thickness coordinate. The
fundamental relations, the equilibrium and stability equations are
derived using the Sander's assumption. Resulting equations are
employed to obtain the closed-form solution for the critical axial
loads. The effects of material properties, geometric size and different
material coefficient on the critical axial loads are examined. The
analytical results are compared and validated using the finite element
model.
Abstract: The main objective of the present paper is to derive an easy numerical technique for the analysis of the free vibration through the stepped regions of plates. Based on the utilities of the step by step integration initial values IV and Finite differences FD methods, the present improved Initial Value Finite Differences (IVFD) technique is achieved. The first initial conditions are formulated in convenient forms for the step by step integrations while the upper and lower edge conditions are expressed in finite difference modes. Also compatibility conditions are created due to the sudden variation of plate thickness. The present method (IVFD) is applied to solve the fourth order partial differential equation of motion for stepped plate across two different panels under the sudden step compatibility in addition to different types of end conditions. The obtained results are examined and the validity of the present method is proved showing excellent efficiency and rapid convergence.
Abstract: The fixed partial dentures are mainly used in the frontal
part of the dental arch because of their great esthetics. There are
several factors that are associated with the stress state created in
ceramic restorations, including: thickness of ceramic layers,
mechanical properties of the materials, elastic modulus of the
supporting substrate material, direction, magnitude and frequency of
applied load, size and location of occlusal contact areas, residual
stresses induced by processing or pores, restoration-cement
interfacial defects and environmental defects. The purpose of this
study is to evaluate the capability of Polarization Sensitive Optical
Coherence Tomography (PSOCT) in detection and analysis of
possible material defects in metal-ceramic and integral ceramic fixed
partial dentures. As a conclusion, it is important to have a non
invasive method to investigate fixed partial prostheses before their
insertion in the oral cavity in order to satisfy the high stress
requirements and the esthetic function.
Abstract: Transdermal delivery of ondansetron hydrochloride (OdHCl) can prevent the problems encountered with oral ondansetron. In previously conducted studies, effect of amount of polyvinyl pyrrolidone, permeation enhancer and casting solvent on the physicochemical properties on OdHCl were investigated. It is feasible to develop ondansetron transdermal patch by using ethyl cellulose and polyvinyl pyrrolidone with dibutyl pthalate as plasticizer, however, the desired flux is not achieved. The primary aim of this study is to use dimethyl succinate (DMS) and propylene glycol that are not incorporated in previous studies to determine their effect on the physicochemical properties of an OdHCl transdermal patch using ethyl cellulose and polyvinyl pyrrolidone. This study also investigates the effect of permeation enhancer (eugenol and phosphatidylcholine) on the release of OdHCl. The results showed that propylene glycol is a more suitable plasticizer compared to DMS in the fabrication of OdHCl transdermal patch using ethyl cellulose and polyvinyl pyrrolidone as polymers. Propylene glycol containing patch has optimum drug content, thickness, moisture content and water absorption, tensile strength, and a better release profile than DMS. Eugenol and phosphatidylcholine can increase release of OdHCl from the patches. From the physicochemical result and permeation profile, a combination of 350mg of ethyl cellulose, 150mg polyvinyl pyrrolidone, 3% of total polymer weight of eugenol, and 40% of total polymer weight of propylene glycol is the most suitable formulation to develop an OdHCl patch. OdHCl release did not increase with increasing the percentage of plasticiser. DMS 4, PG 4, DMS 9, PG 9, DMS 14, and PG 14 gave better release profiles where using 300mg: 0mg, 300mg: 100mg, and 350mg: 150mg of EC: PVP. Thus, 40% of PG or DMS appeared to be the optimum amount of plasticiser when the above combination where EC: PVP was used. It was concluded from the study that a patch formulation containing 350mg EC, 150mg PVP, 40% PG and 3% eugenol is the best transdermal matrix patch compositions for the uniform and continuous release/permeation of OdHCl over an extended period. This patch design can be used for further pharmacokinetic and pharmacodynamic studies in suitable animal models.
Abstract: We propose photo-BJMOSFET (Bipolar Junction Metal-Oxide-Semiconductor Field Effect Transistor) fabricated on SOI film. ITO film is adopted in the device as gate electrode to reduce light absorption. I-V characteristics of photo-BJMOSFET obtained in dark (dark current) and under 570nm illumination (photo current) are studied furthermore to achieve high photo-to-dark-current contrast ratio. Two variables in the calculation were the channel length and the thickness of the film which were set equal to six different values, i.e., L=2, 4, 6, 8, 10, and 12μm and three different values, i.e., dsi =100, 200 and 300nm, respectively. The results indicate that the greatest photo-to-dark-current contrast ratio is achieved with L=10μm and dsi=200 nm at VGK=0.6V.
Abstract: In this paper, the innovative intelligent fuzzy weighted
input estimation method (FWIEM) can be applied to the inverse heat
transfer conduction problem (IHCP) to estimate the unknown
time-varying heat flux efficiently as presented. The feasibility of this
method can be verified by adopting the temperature measurement
experiment. We would like to focus attention on the heat flux
estimation to three kinds of samples (Copper, Iron and Steel/AISI 304)
with the same 3mm thickness. The temperature measurements are then
regarded as the inputs into the FWIEM to estimate the heat flux. The
experiment results show that the proposed algorithm can estimate the
unknown time-varying heat flux on-line.
Abstract: This paper describes analysis of low velocity transverse impact on fully backed sandwich beams with composite faces from Eglass/epoxy and cores from Polyurethane or PVC. Indentation on sandwich beams has been analyzed with the existing theories and modeled with the FE code ABAQUS, also loadings have been done experimentally to verify theoretical results. Impact on fully backed has been modeled in two cases of impactor energy with SDOF model (single-degree-of-freedom) and indentation stiffness: lower energy for elastic indentation of sandwich beams and higher energy for plastic area in indentation. Impacts have been modeled by ABAQUS. Impact results can describe response of beam in terms of core and faces thicknesses, core material, indentor energy and energy absorbed. The foam core is modeled using the crushable foam material model and response of the foam core is experimentally characterized in uniaxial compression with higher velocity loading to define quasi impact behaviour.
Abstract: Today, Hydroforming technology provides an
attractive alternative to conventional matched die forming, especially
for cost-sensitive, lower volume production, and for parts with
irregular contours. In this study the critical fluid pressures which lead
to rupture in the workpiece has been investigated by theoretical and
finite element methods. The axisymmetric analysis was developed to
investigate the tearing phenomenon in cylindrical Hydroforming
Deep Drawing (HDD). By use of obtained equations the effect of
anisotropy, drawing ratio, sheet thickness and strain hardening
exponent on tearing diagram were investigated.
Abstract: Studies have shown that the SnAgCu solder family has been widely used as a replacement for conventional Sn-Pb solders. An attractive approach is by introducing alloying additives (rare earth elements (RE), Zn, Co, Fe, Ni, Sb) into the SnAgCu solder, which helps in refining the microstructure also improving the mechanical and wetting properties of the solder. The present work focuses on the effect of additions of 0.5% Ce and Fe into Sn-3.0Ag-0.5Cu solder, in attempt to reduce the intermetallic compound (IMC) growth and reflow properties of the solder on Cu and Ni (P) surface finish, as well as effects thermal aging on the formation of intermetallic compound (IMC) on different surface finish. Excessive intermetallic compound growth may effect the interface and solder joint due to the brittle nature of the intermetallic compounds. Thus, by introducing alloying elements, IMC layer thickness can be decrease, resulting in better joint and solder reliability.
Abstract: The plastic forming process of sheet plate takes an
important place in forming metals. The traditional techniques of tool
design for sheet forming operations used in industry are experimental
and expensive methods. Prediction of the forming results,
determination of the punching force, blank holder forces and the
thickness distribution of the sheet metal will decrease the production
cost and time of the material to be formed. In this paper, multi-stage
deep drawing simulation of an Industrial Part has been presented
with finite element method. The entire production steps with
additional operations such as intermediate annealing and springback
has been simulated by ABAQUS software under axisymmetric
conditions. The simulation results such as sheet thickness
distribution, Punch force and residual stresses have been extracted in
any stages and sheet thickness distribution was compared with
experimental results. It was found through comparison of results, the
FE model have proven to be in close agreement with those of
experiment.
Abstract: Chaiyaphum Starch Co. Ltd. is one of many starch
manufacturers that has introduced machinery to aid in manufacturing.
Even though machinery has replaced many elements and is now a
significant part in manufacturing processes, problems that must be
solved with respect to current process flow to increase efficiency still
exist. The paper-s aim is to increase productivity while maintaining
desired quality of starch, by redesigning the flipping machine-s
mechanical control system which has grossly low functional lifetime.
Such problems stem from the mechanical control system-s bearings,
as fluids and humidity can access into said bearing directly, in
tandem with vibrations from the machine-s function itself. The wheel
which is used to sense starch thickness occasionally falls from its
shaft, due to high speed rotation during operation, while the shaft
may bend from impact when processing dried bread. Redesigning its
mechanical control system has increased its efficiency, allowing
quality thickness measurement while increasing functional lifetime
an additional 62 days.
Abstract: The aim of this work is to analyze a viscous flow in
the axisymmetric nozzle taken into account the mesh size both in the
free stream and into the boundary layer. The resolution of the Navier-
Stokes equations is realized by using the finite volume method to
determine the supersonic flow parameters at the exit of convergingdiverging
nozzle. The numerical technique uses the Flux Vector
Splitting method of Van Leer. Here, adequate time stepping
parameter, along with CFL coefficient and mesh size level is selected
to ensure numerical convergence. The effect of the boundary layer
thickness is significant at the exit of the nozzle. The best solution is
obtained with using a very fine grid, especially near the wall, where
we have a strong variation of velocity, temperature and shear stress.
This study enabled us to confirm that the determination of boundary
layer thickness can be obtained only if the size of the mesh is lower
than a certain value limits given by our calculations.
Abstract: Manufacturing components of fiber-reinforced
thermoplastics requires three steps: heating the matrix, forming and
consolidation of the composite and terminal cooling the matrix. For
the heating process a pre-determined temperature distribution through
the layers and the thickness of the pre-consolidated sheets is
recommended to enable forming mechanism. Thus, a design for the
heating process for forming composites with thermoplastic matrices
is necessary. To obtain a constant temperature through thickness and
width of the sheet, the heating process was analyzed by the help of
the finite element method. The simulation models were validated by
experiments with resistance thermometers as well as with an infrared
camera. Based on the finite element simulation, heating methods for
infrared radiators have been developed. Using the numeric
simulation many iteration loops are required to determine the process
parameters. Hence, the initiation of a model for calculating relevant
process parameters started applying regression functions.
Abstract: In this paper, an automated system is presented for
identification and separation of plastic resins based on near infrared
(NIR) reflectance spectroscopy. For identification and separation
among resins, a "Two-Filter" identification method is proposed that
is capable to distinguish among polyethylene terephthalate (PET),
high density polyethylene (HDPE), polyvinyl chloride (PVC),
polypropylene (PP) and polystyrene (PS). Through surveying effects
of parameters such as surface contamination, sample thickness, label
and cap existence, it was obvious that the "Two-Filter" method has a
high efficiency in identification of resins. It is shown that accurate
identification and separation of five major resins can be obtained
through calculating the relative reflectance at two wavelengths in the
NIR region.
Abstract: Nanofluids are novel fluids that are going to have an
important role in future industrial thermal device designs. Studies are
being predominantly conducted on the mechanism of these heat
transfers. The key to this attraction is in the increase in thermal
conductivity brought about by the Nanofluids compared with the
base fluid. Different models have been proposed for calculation of
effective thermal conduction that has been gradually modified. In this
investigation effect of nanolayer structure and Brownian motion of
particles are studied and a new modified thermal conductivity model
is proposed. Temperature, concentration, nanolayer thickness and
particle size are taken as variables and their effect are studied
simultaneously on the thermal conductivity of the fluids, showing the
concentration of the nanoparticles to affect the nanolayer thickness
which also affects the Brownian motion.
Abstract: Laser engraving is a manufacturing method for those applications where previously Electrical Discharge Machining (EDM) was the only choice. Laser engraving technology removes material layer-by-layer and the thickness of layers is usually in the range of few microns. The aim of the present work is to investigate the influence of the process parameters on the surface quality when machined by laser engraving. The examined parameters were: the pulse frequency, the beam speed and the layer thickness. The surface quality was determined by the surface roughness for every set of parameters. Experimental results on Al7075 material showed that the surface roughness strictly depends on the process parameters used.
Abstract: Metal cutting is a severe plastic deformation process
involving large strains, high strain rates, and high temperatures.
Conventional analysis of the chip formation process is based on bulk
material deformation disregarding the inhomogeneous nature of the
material microstructure. A series of orthogonal cutting tests of AISI
1045 and 1144 steel were conducted which yielded similar process
characteristics and chip formations. With similar shear angles and cut
chip thicknesses, shear strains for both chips were found to range
from 2.0 up to 2.8. The manganese-sulfide (MnS) precipitate in the
1144 steel has a very distinct and uniform shape which allows for
comparison before and after chip formation. From close observations
of MnS precipitates in the cut chips it is shown that the conventional
approach underestimates plastic strains in metal cutting.
Experimental findings revealed local shear strains around a value of
6. These findings and their implications are presented and discussed.
Abstract: Pressure vessels are usually operating at temperatures
where the conditions of linear elastic fracture mechanics are no
longer met because massive plasticity precedes crack propagation. In
this work the development of a surface crack in a pressure vessel
subject to bending and tension under elastic-plastic fracture
mechanics conditions was investigated. Finite element analysis was
used to evaluate the hydrostatic stress, the J-integral and crack
growth for semi-elliptical surface-breaking cracks. The results
showed non-uniform stress triaxiality and crack driving force around
the crack front at large deformation levels. Different ductile crack
extensions were observed which emphasis the dependent of ductile
tearing on crack geometry and type of loading. In bending the crack
grew only beneath the surface, and growth was suppressed at the
deepest segment. This contrasts to tension where the crack breaks
through the thickness with uniform growth along the entire crack
front except at the free surface. Current investigations showed that
the crack growth developed under linear elastic fracture mechanics
conditions will no longer be applicable under ductile tearing
scenarios.
Abstract: This paper investigates vortex shedding processes
occurring at the end of a stack of parallel plates, due to an oscillating
flow induced by an acoustic standing wave within an acoustic
resonator. Here, Particle Image Velocimetry (PIV) is used to quantify
the vortex shedding processes within an acoustic cycle
phase-by-phase, in particular during the “ejection" of the fluid out of
the stack. Standard hot-wire anemometry measurement is also applied
to detect the velocity fluctuations near the end of the stack.
Combination of these two measurement techniques allowed a detailed
analysis of the vortex shedding phenomena. The results obtained show
that, as the Reynolds number varies (by varying the plate thickness
and drive ratio), different flow patterns of vortex shedding are
observed by the PIV measurement. On the other hand, the
time-dependent hot-wire measurements allow obtaining detailed
frequency spectra of the velocity signal, used for calculating
characteristic Strouhal numbers. The impact of the plate thickness and
the Reynolds number on the vortex shedding pattern has been
discussed. Furthermore, a detailed map of the relationship between the
Strouhal number and Reynolds number has been obtained and
discussed.