Abstract: Power quality is used to describe the degree of consistency of electrical energy expected from generation source to point of use. The term power quality refers to a wide variety of electromagnetic phenomena that characterize the voltage and current at a given time and at a given location on the power system. Power quality problems can be defined as problem that results in failure of customer equipments, which manifests itself as an economic burden to users, or produces negative impacts on the environment. Voltage stability, power factor, harmonics pollution, reactive power and load unbalance are some of the factors that affect the consistency or the quality level. This research proposal proposes to investigate and analyze the causes and effects of power quality to homes and industries in Sarawak. The increasing application of electronics equipment used in the industries and homes has caused a big impact on the power quality. Many electrical devices are now interconnected to the power network and it can be observed that if the power quality of the network is good, then any loads connected to it will run smoothly and efficiently. On the other hand, if the power quality of the network is bad, then loads connected to it will fail or may cause damage to the equipments and reduced its lifetime. The outcome of this research will enable better and novel solutions of poor power quality to small industries and reduce damage of electrical devices and products in the industries.
Abstract: Electrification is a complex process and governed by various parameters. Modeling of power plant’s target efficiency or target heat rate is often formulated and compared with the actual values. This comparison not only implies the performance of the power plant but also reflects the energy losses possibly inherited in some of related equipment and processes. The current modeling of Coal-fired Mae Moh power plant was formulated at the first commissioning. Some of equipments were replaced due to its life time. Relatively outdated for 20 years, the utilization of the model is not accomplished. This work has focused on the development of the performance analysis model of aforementioned power plant according to the most updated and current working conditions. The model is more appropriate and shows accuracy in its analysis. Losses are detected and measures are introduced such that reduction in energy consumption, related cost, and also environment impacts can be anticipated.
Abstract: The purpose of the study is to analyze the main tourism attraction in indigenous tribes, as well as for the development of tribal aboriginal tourism brings positive and negative impacts. This study used qualitative research methods, and Lilang, Tbulan, and Hrung three tribes as the object of investigation. The results showed that: 1. Because three tribes geographical proximity, but have their own development characteristics, not conflict situations. 2. Three tribes are located in National Scenic Area and National Forest Recreation Area near, so driven tribal tourism development. 3 In addition Hrung three tribal tribal no major attraction, mainly located in the provision of accommodation; another Lilang and Tbulan tribe has natural resources and cultural resources attraction. 4 in the tourism brings positive and negative impacts, respondents expressed positive than residents of negative impacts. Based on the above findings, this study not only provides advice for tribal tourism operators, but also for future research to provide specific directions.
Abstract: Taiwan was the first country in Asia to announce
“Nuclear-Free Homeland" in 2002. In 2008, the new government
released the Sustainable Energy Policy Guidelines to lower the
nationwide CO2 emissions some time between 2016 and 2020 back to
the level of year 2008, further abatement of CO2 emissions is planed in
year 2025 when CO2 emissions will decrease to the level of year 2000.
Besides, under consideration of the issues of energy, environment and
economics (3E), the new government declared that the nuclear power
is a carbon-less energy option. This study analyses the effects of
nuclear power generation for CO2 abatement scenarios in Taiwan. The
MARKAL-MACRO energy model was adopted to evaluate economic
impacts and energy deployment due to life extension of existing
nuclear power plants and build new nuclear power units in CO2
abatement scenarios. The results show that CO2 abatement effort is
expensive. On the other hand, nuclear power is a cost-effective choice.
The GDP loss rate in the case of building new nuclear power plants is
around two thirds of the Nuclear-Free Homeland case. Nuclear power
generation has the capacity to provide large-scale CO2 free electricity.
Therefore, the results show that nuclear power is not only an option for
Taiwan, but also a requisite for Taiwan-s CO2 reduction strategy.
Abstract: The impacts of near-campus student housing, or offcampus
students accommodation cannot be ignored by the
universities and as well as the community officials. Numerous
scholarly studies, have highlighted the substantial economic impacts
either; direct, indirect or induced, and cumulatively the roles of the
universities have significantly contributed to the local economies.
The issue of the impacts of off-campus student rental housing on
neighbourhoods is one that has been of long-standing but increasing
concern in Malaysia. Statistically, in Malaysia, there was
approximately a total of 1.2 - 1.5 million students in 2009. By the
year 2015, it is expected that 50 per cent of 18 to 30 year olds active
population should gain access to university education, amounting to
120,000 yearly. The objectives of the research are to assess the
impacts off-campus students on the local neighbourhood and
specifically to obtain information on the living and learning
conditions of off-campus students of Universiti Teknologi MARA
Shah Alam, Malaysia. It is also to isolate those factors that may
impede the successful learning so that priority can be given to them
in subsequent policy implementations and actions by government and
the higher education institutions.
Abstract: New ways of working- refers to non-traditional work practices, settings and locations with information and communication technologies (ICT) to supplement or replace traditional ways of working. It questions the contemporary work practices and settings still very much used in knowledge-intensive organizations today. In this study new ways of working is seen to consist of two elements: work environment (incl. physical, virtual and social) and work practices. This study aims to gather the scattered information together and deepen the understanding on new ways of working. Moreover, the objective is to provide some evidence of the unclear productivity impacts of new ways of working using case study approach.
Abstract: The benefits of eco-roofs is quite well known, however there remains very little research conducted for the implementation of eco-roofs in subtropical climates such as Australia. There are many challenges facing Australia as it moves into the future, climate change is proving to be one of the leading challenges. In order to move forward with the mitigation of climate change, the impacts of rapid urbanization need to be offset. Eco-roofs are one way to achieve this; this study presents the energy savings and environmental benefits of the implementation of eco-roofs in subtropical climates. An experimental set-up was installed at Rockhampton campus of Central Queensland University, where two shipping containers were converted into small offices, one with an eco-roof and one without. These were used for temperature, humidity and energy consumption data collection. In addition, a computational model was developed using Design Builder software (state-of-the-art building energy simulation software) for simulating energy consumption of shipping containers and environmental parameters, this was done to allow comparison between simulated and real world data. This study found that eco-roofs are very effective in subtropical climates and provide energy saving of about 13% which agrees well with simulated results.
Abstract: Any use of energy in industrial productive activities is combined with various environment impacts. Withintransportation,
this fact was not only found among land transport, railways and maritime transport, but also in the air transport industry. An effective climate protection requires strategies and measures for reducing all
greenhouses gas emissions, in particular carbon dioxide, and must
take into account the economic, ecologic and social aspects. It seem simperative now to develop and manufacture environmentally
friendly products and systems, to reduce consumption and use less
resource, and to save energy and power. Today-sproducts could
better serve these requirements taking into account the integration of
a power management system into the electrical power system.This
paper gives an overview of an approach ofpower management with
load prioritization in modernaircraft. Load dimensioning and load
management strategies on current civil aircraft will be presented and
used as a basis for the proposed approach.
Abstract: Post-disaster reconstruction projects offer
opportunities to facilitate physical, social and economic development
and to reduce future hazard vulnerability long after the disasters.
Sustainability of post-disaster reconstruction project conducted in the
villages of Dinar following the 1995 earthquake was investigated in
this paper. Officials of the Government who were involved in the
project were interviewed. Besides, two field surveys were done in 12
villages of Dinar in winter months of 2008. Beneficiaries were
interviewed and physical, socio-cultural and economic impacts of the
reconstruction were examined. The research revealed that the postdisaster
reconstruction project has negative aspects from the point
view of sustainability. The physical, socio-cultural and economic
factors were not considered during decision making process of the
project.
Abstract: Building condition assessment is a critical activity in Malaysia-s Comprehensive Asset Management Model. It is closely related to building performance that impact user-s life and decision making. This study focuses on public primary school, one of the most valuable assets for the country. The assessment was carried out based on CSP1 Matrix in Kuching Division of Sarawak, Malaysia. Based on the matrix used, three main criteria of the buildings has successfully evaluate: the number of defects; schools rating; and total schools rating. The analysis carried out on 24 schools found that the overall 4, 725 defects has been identified. Meanwhile, the overall score obtained was 45, 868 and the overall rating is 9.71, which is at the fair condition. This result has been associated with building age to evaluate its impacts on school buildings condition. The findings proved that building condition is closely related to building age and its support the theory that 'the ageing building has more defect than the new one'.
Abstract: Success is a European project that will implement several clean transport offers in three European cities and evaluate the environmental impacts. The goal of these measures is to improve urban mobility or the displacement of residents inside cities. For e.g. park and ride, electric vehicles, hybrid bus and bike sharing etc. A list of 28 criteria and 60 measures has been established for evaluation of these transport projects. The evaluation criteria can be grouped into: Transport, environment, social, economic and fuel consumption. This article proposes a decision support system based that encapsulates a hybrid approach based on fuzzy logic, multicriteria analysis and belief theory for the evaluation of impacts of urban mobility solutions. A web-based tool called DeSSIA (Decision Support System for Impacts Assessment) has been developed that treats complex data. The tool has several functionalities starting from data integration (import of data), evaluation of projects and finishes by graphical display of results. The tool development is based on the concept of MVC (Model, View, and Controller). The MVC is a conception model adapted to the creation of software's which impose separation between data, their treatment and presentation. Effort is laid on the ergonomic aspects of the application. It has codes compatible with the latest norms (XHTML, CSS) and has been validated by W3C (World Wide Web Consortium). The main ergonomic aspect focuses on the usability of the application, ease of learning and adoption. By the usage of technologies such as AJAX (XML and Java Script asynchrones), the application is more rapid and convivial. The positive points of our approach are that it treats heterogeneous data (qualitative, quantitative) from various information sources (human experts, survey, sensors, model etc.).
Abstract: This paper analysis the tourism development on the
Red Sea in Egypt (west bank) and the needed ongoing action toward
a sustainable approach. It addresses, at the first, the development's
evolution occurred in the coastal area, the environmental effects it
left, and how to minimize those impacts in the future. The second
main point is dealing with the most important issues that hinder the
achievement of sustainable tourism development on the Red Sea
coast and how we can overcome them in the future.
Abstract: The management of the health-care wastes is one of
the most important problems in Istanbul, a city with more than 12
million inhabitants, as it is in most of the developing countries.
Negligence in appropriate treatment and final disposal of the healthcare
wastes can lead to adverse impacts to public health and to the
environment. This paper employs a fuzzy multi-criteria group
decision making approach, which is based on the principles of fusion
of fuzzy information, 2-tuple linguistic representation model, and
technique for order preference by similarity to ideal solution
(TOPSIS), to evaluate health-care waste (HCW) treatment
alternatives for Istanbul. The evaluation criteria are determined
employing nominal group technique (NGT), which is a method of
systematically developing a consensus of group opinion. The
employed method is apt to manage information assessed using multigranularity
linguistic information in a decision making problem with
multiple information sources. The decision making framework
employs ordered weighted averaging (OWA) operator that
encompasses several operators as the aggregation operator since it
can implement different aggregation rules by changing the order
weights. The aggregation process is based on the unification of
information by means of fuzzy sets on a basic linguistic term set
(BLTS). Then, the unified information is transformed into linguistic
2-tuples in a way to rectify the problem of loss information of other
fuzzy linguistic approaches.
Abstract: This study aims to investigate empirically the valuerelevance
of accounting information to domestic investors in Tehran
stock exchange from 1999 to 2006. During the present research
impacts of two factors, including positive vs. negative earnings and
the firm size are considered as well. The authors used earnings per
share and annual change of earnings per share as the income
statement indices, and book value of equity per share as the balance
sheet index. Return and Price models through regression analysis are
deployed in order to test the research hypothesis. Results depicted
that accounting information is value-relevance to domestic investors
in Tehran Stock Exchange according to both studied models.
However, income statement information has more value-relevance
than the balance sheet information. Furthermore, positive vs. negative
earnings and firm size seems to have significant impact on valuerelevance
of accounting information.
Abstract: The concepts of knowledge creation and innovation
have a strong relationship but this relationship has not been examined
systematically. This study examines the utilization of knowledge
creation processes of the Theory of Knowledge Creation in Higher
Education Institutions. These processes consist of socialization,
externalization, combination and internalization. This study suggests
that the utilization of these processes will give impacts on innovation
in academic performance. A cross-sectional study was conducted
using survey questionnaires to collect data of the utilization of
knowledge creation processes and classroom-s innovation. The
samples are Business Management students of a Malaysian Higher
Education Institution. The results of this study could help Higher
Education Institutions to enrich the learning process of students
through knowledge creation and innovation.
Abstract: Green home rating has emerged as an important
agenda to practice the principles of sustainability. In Malaysia, the
establishment of the 'Green Building Index ' Residential New
Construction- (GBI-RNC) has brought this agenda closer to the
stakeholders of the local green building industry. GBI-RNC focuses
on the evaluation of the environmental impacts posed by houses
rather than assessing the Triple-Bottom-Line (TBL) of Sustainability
which also include socio-economic factors. Therefore, as part of a
wider study, a survey was conducted to gather the backgrounds of
green building stakeholders in Malaysia and their responses to a
number of exploratory questions regarding the setting up of a
framework to rate green homes against the TBL. This paper reports
the findings from Section A and B from this survey and discusses
them accordingly with a conclusion that forms part of the basis for a
new generation green home rating framework specifically for use in
Malaysia.
Abstract: One of the essential sectors of Myanmar economy is
agriculture which is sensitive to climate variation. The most
important climatic element which impacts on agriculture sector is
rainfall. Thus rainfall prediction becomes an important issue in
agriculture country. Multi variables polynomial regression (MPR)
provides an effective way to describe complex nonlinear input output
relationships so that an outcome variable can be predicted from the
other or others. In this paper, the modeling of monthly rainfall
prediction over Myanmar is described in detail by applying the
polynomial regression equation. The proposed model results are
compared to the results produced by multiple linear regression model
(MLR). Experiments indicate that the prediction model based on
MPR has higher accuracy than using MLR.
Abstract: One of the most important power quality issues is voltage flicker. Nowadays this issue also impacts the power system all over the world. The fact of the matter is that the more and the larger capacity of wind generator has been installed. Under unstable wind power situation, the variation of output current and voltage have caused trouble to voltage flicker. Hence, the major purpose of this study is to analyze the impact of wind generator on voltage flicker of power system. First of all, digital simulation and analysis are carried out based on wind generator operating under various system short circuit capacity, impedance angle, loading, and power factor of load. The simulation results have been confirmed by field measurements.
Abstract: Careful design and selection of daylighting systems can greatly help in reducing not only artificial lighting use, but also decrease cooling energy consumption and, therefore, potential for downsizing air-conditioning systems. This paper aims to evaluate the energy performance of two types of top-light daylighting systems due to the integration of daylight together with artificial lighting in an existing examinaton hall in University Kebangsaan Malaysia, based on a hot and humid climate. Computer simulation models have been created for building case study (base case) and the two types of toplight daylighting designs for building energy performance evaluation using the VisualDOE 4.0 building energy simulation program. The finding revealed that daylighting through top-light systems is a very beneficial design strategy in reducing annual lighting energy consumption and the overall total annual energy consumption.
Abstract: A variety of new technology-based services have
emerged with the development of Information and Communication
Technologies (ICTs). Since technology-based services have technology-driven characteristics, the identification of relationships
between technology-based services and ICTs would give meaningful implications. Thus, this paper proposes an approach for identifying the
relationships between technology-based services and ICTs by
analyzing patent documents. First, business model (BM) patents are
classified into relevant service categories. Second, patent citation
analysis is conducted to investigate the technological linkage and impacts between technology-based services and ICTs at macro level.
Third, as a micro level analysis, patent co-classification analysis is
employed to identify the technological linkage and coverage. The
proposed approach could guide and help managers and designers of
technology-based services to discover the opportunity of the development of new technology-based services in emerging service sectors.