Abstract: The main goal of the study is to analyze all relevant
properties of the electro hydraulic systems and based on that to make
a proper choice of the control strategy that may be used for the
control of the servomechanism system. A combination of electronic
and hydraulic systems is widely used since it combines the
advantages of both. Hydraulic systems are widely spread because of
their properties as accuracy, flexibility, high horsepower-to-weight
ratio, fast starting, stopping and reversal with smoothness and
precision, and simplicity of operations. On the other hand, the
modern control of hydraulic systems is based on control of the circuit
fed to the inductive solenoid that controls the position of the
hydraulic valve. Since this circuit may be easily handled by PWM
(Pulse Width Modulation) signal with a proper frequency, the
combination of electrical and hydraulic systems became very fruitful
and usable in specific areas as airplane and military industry.
The study shows and discusses the experimental results obtained
by the control strategy (classical feedback (PID) & neural network)
using MATLAB and SIMULINK [1]. Finally, the special attention
was paid to the possibility of neuro-controller design and its
application to control of electro-hydraulic systems and to make
comparative with classical control.
Abstract: Relay based communication has gained considerable importance in the recent years. In this paper we find the end-toend statistics of a two hop non-regenerative relay branch, each hop being Nakagami-m faded. Closed form expressions for the probability density functions of the signal envelope at the output of a selection combiner and a maximal ratio combiner at the destination node are also derived and analytical formulations are verified through computer simulation. These density functions are useful in evaluating the system performance in terms of bit error rate and outage probability.
Abstract: Many states are now committed to implementing
international human rights standards domestically. In terms of
practical governance, how might effectiveness be measured? A facevalue
answer can be found in domestic laws and institutions relating
to human rights. However, this article provides two further tools to
help states assess their status on the spectrum of robust to fragile
human rights governance. The first recognises that each state has its
own 'human rights history' and the ideal end stage is robust human
rights governance, and the second is developing criteria to assess
robustness. Although a New Zealand case study is used to illustrate
these tools, the widespread adoption of human rights standards by
many states inevitably means that the issues are relevant to other
countries. This is even though there will always be varying degrees of
similarity-difference in constitutional background and developed or
emerging human rights systems.
Abstract: It has formed an essential issue that Climate Change, composed of highly knowledge complexity, reveals its significant impact on human existence. Therefore, specific national policies, some of which present the educational aspects, have been published for overcoming the imperative problem. Accordingly, the study aims to analyze as well as integrate the relationship between Climate Change and environmental education and apply the perspective of concept map to represent the knowledge contents and structures of Climate Change; by doing so, knowledge contents of Climate Change could be represented in an even more comprehensive way and manipulated as the tool for environmental education. The method adapted for this study is knowledge conversion model compounded of the platform for experts and teachers, who were the participants for this study, to cooperate and combine each participant-s standpoints into a complete knowledge framework that is the foundation for structuring the concept map. The result of this research contains the important concepts, the precise propositions and the entire concept map for representing the robust concepts of Climate Change.
Abstract: A state of the art Speaker Identification (SI) system
requires a robust feature extraction unit followed by a speaker
modeling scheme for generalized representation of these features.
Over the years, Mel-Frequency Cepstral Coefficients (MFCC)
modeled on the human auditory system has been used as a standard
acoustic feature set for speech related applications. On a recent
contribution by authors, it has been shown that the Inverted Mel-
Frequency Cepstral Coefficients (IMFCC) is useful feature set for
SI, which contains complementary information present in high
frequency region. This paper introduces the Gaussian shaped filter
(GF) while calculating MFCC and IMFCC in place of typical
triangular shaped bins. The objective is to introduce a higher
amount of correlation between subband outputs. The performances
of both MFCC & IMFCC improve with GF over conventional
triangular filter (TF) based implementation, individually as well as
in combination. With GMM as speaker modeling paradigm, the
performances of proposed GF based MFCC and IMFCC in
individual and fused mode have been verified in two standard
databases YOHO, (Microphone Speech) and POLYCOST
(Telephone Speech) each of which has more than 130 speakers.
Abstract: This paper focuses on the Mega-Sub Controlled
Structure Systems (MSCSS) performances and characteristics
regarding the new control principle contained in MSCSS subjected to
strong earthquake excitations. The adopted control scheme consists of
modulated sub-structures where the control action is achieved by
viscous dampers and sub-structure own configuration. The
elastic-plastic time history analysis under severe earthquake excitation
is analyzed base on the Finite Element Analysis Method (FEAM), and
some comparison results are also given in this paper. The result shows
that the MSCSS systems can remarkably reduce vibrations effects
more than the mega-sub structure (MSS). The study illustrates that the
improved MSCSS presents good seismic resistance ability even at 1.2g
and can absorb seismic energy in the structure, thus imply that
structural members cross section can be reduce and achieve to good
economic characteristics. Furthermore, the elasto-plastic analysis
demonstrates that the MSCSS is accurate enough regarding
international building evaluation and design codes. This paper also
shows that the elasto-plastic dynamic analysis method is a reasonable
and reliable analysis method for structures subjected to strong
earthquake excitations and that the computed results are more precise.
Abstract: In diversity rich environments, such as in Ultra-
Wideband (UWB) applications, the a priori determination of the
number of strong diversity branches is difficult, because of the considerably large number of diversity paths, which are characterized
by a variety of power delay profiles (PDPs). Several
Rake implementations have been proposed in the past, in order to reduce the number of the estimated and combined paths. To this
aim, we introduce two adaptive Rake receivers, which combine
a subset of the resolvable paths considering simultaneously the
quality of both the total combining output signal-to-noise ratio (SNR) and the individual SNR of each path. These schemes achieve
better adaptation to channel conditions compared to other known receivers, without further increasing the complexity. Their performance
is evaluated in different practical UWB channels, whose models are based on extensive propagation measurements. The
proposed receivers compromise between the power consumption,
complexity and performance gain for the additional paths, resulting in important savings in power and computational resources.
Abstract: This study presents the improvement of thermal
performance of heat pipe using copper nanofluid with aqueous
solution of n-Butanol. The nanofluids kept in the suspension of
conventional fluids have the potential of superior heat transfer
capability than the conventional fluids due to their improved thermal
conductivity. In this work, the copper nanofluid which has a 40 nm
size with a concentration of 100 mg/lit is kept in the suspension of
the de-ionized (DI) water and an aqueous solution of n-Butanol and
these fluids are used as a working medium in the heat pipe. The study
discusses about the effect of heat pipe inclination, type of working
fluid and heat input on the thermal efficiency and thermal resistance.
The experimental results are evaluated in terms of its performance
metrics and are compared with that of DI water.
Abstract: Increasing the demand for effectively use of the
production facility requires the tools for sharing the manufacturing
facility through remote operation of the machining process. This
research introduces the methodology of machining technology for
direct remote operation of networked milling machine. The
integrated tools with virtual simulation, remote desktop protocol and
Setup Free Attachment for remote operation of milling process are
proposed. Accessing and monitoring of machining operation is
performed by remote desktop interface and 3D virtual simulations.
Capability of remote operation is supported by an auto setup
attachment with a reconfigurable pin type setup free technology
installed on the table of CNC milling machine to perform unattended
machining process. The system is designed using a computer server
and connected to a PC based controlled CNC machine for real time
monitoring. A client will access the server through internet
communication and virtually simulate the machine activity. The
result has been presented that combination between real time virtual
simulation and remote desktop tool is enabling to operate all machine
tool functions and as well as workpiece setup..
Abstract: There has been a growing interest in utilizing surfactants in remediation processes to separate the hydrophobic volatile organic compounds (HVOCs) from aqueous solution. One attractive process is cloud point extraction (CPE), which utilizes nonionic surfactants as a separating agent. Since the surfactant cost is a key determination of the economic viability of the process, it is important that the surfactants are recycled and reused. This work aims to study the performance of the co-current vacuum stripping using a packed column for HVOCs removal from contaminated surfactant solution. Six types HVOCs are selected as contaminants. The studied surfactant is the branched secondary alcohol ethoxylates (AEs), Tergitol TMN-6 (C14H30O2). The volatility and the solubility of HVOCs in surfactant system are determined in terms of an apparent Henry’s law constant and a solubilization constant, respectively. Moreover, the HVOCs removal efficiency of vacuum stripping column is assessed in terms of percentage of HVOCs removal and the overall liquid phase volumetric mass transfer coefficient. The apparent Henry’s law constant of benzenz , toluene, and ethyl benzene were 7.00×10-5, 5.38×10-5, 3.35× 10-5 respectively. The solubilization constant of benzene, toluene, and ethyl benzene were 1.71, 2.68, 7.54 respectively. The HVOCs removal for all solute were around 90 percent.
Abstract: In this study concept of experimental design is
successfully applied for the determination of optimum condition to
produce PP/SWCNT (Polypropylene/Single wall carbon nanotube)
nanocomposite. Central composite design as one of experimental
design techniques is employed for the optimization and statistical
determination of the significant factors influencing on the tensile
modulus and yield stress as mechanical properties of this
nanocomposite. The significant factors are SWCNT weight fraction
and acid treatment time for functionalizing the nanoparticles.
Optimum conditions are in 0.7 % of SWCNT weight fraction and 210
min as acid treatment time for 1112.75 ± 28 MPa as maximum tensile
modulus and in 216 min and 0.65 % as acid treatment time and
SWCNT weight fraction respectively for 40.26 ± 0.3 MPa as
maximum yield stress. Also after setting new experiments for test
these optimum conditions, found excelent agreement with predicted
values.
Abstract: Tourists- eyes will often be attracted by the unique
phenomenon of the roadsides: betel nut beauties (pronounced as
binlang xishi in Mandarin), if they drive on the roads of Taiwan.
Sitting in the neon-lit glass stalls with attractive dress on the roadsides,
betel nut beauties usually sell betel nuts to the passing truckers or car
drivers with much of their efforts. Moreover, in order to attract
peoples- eyesight and increase the sales volume, the young girls are in
skimpy clothing to promote betel nuts or beverages to their customers.
Therefore, when the Chinese tourists come to Taiwan, to see the
unique betel nut beauty phenomenon has become one of their greatly
interested things or even a “must see". This paper describes betel but
beauties in Taiwan, explained why the Chinese tourists like to see
them in Taiwan and proposed propositions for examination.
Abstract: This paper reports on a receding horizon filtering for
mobile robot systems with cross-correlated sensor noises and
uncertainties. Also, the effect of uncertain parameters in the state of
the tracking error model performance is considered. A distributed
fusion receding horizon filter is proposed. The distributed fusion
filtering algorithm represents the optimal linear combination of the
local filters under the minimum mean square error criterion. The
derivation of the error cross-covariances between the local receding
horizon filters is the key of this paper. Simulation results of the
tracking mobile robot-s motion demonstrate high accuracy and
computational efficiency of the distributed fusion receding horizon
filter.
Abstract: Many Thai movies have been very popular
domestically and internationally. Some movies were box office hits
and receiving awards. However, there has not yet been research
about how Thai movies can sell in international markets
The objectives of the research were 1) To analyze the
characteristics of Thai movies that can sell to world audiences; 2) To
investigate the factors making Thai movies into foreign markets. Thai
film professionals were interviewed. Their ideas were analyzed to
find out what factors contributing to Thai movies widely seen in
worldwide markets. Nine foreign audiences were also interviewed to
reveal what characteristics of Thai movies would be well accepted by
the markets.
The results showed that major characteristics of Thai movies
proving successful worldwide were cultural and exotic Thai movies,
outstanding genres, well-known actors, music and songs. Factors
contributing to global market were marketing, qualities of Thai
movies, and financial support from the government.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: In this paper, estimation of the linear regression
model is made by ordinary least squares method and the
partially linear regression model is estimated by penalized
least squares method using smoothing spline. Then, it is
investigated that differences and similarity in the sum of
squares related for linear regression and partial linear
regression models (semi-parametric regression models). It is
denoted that the sum of squares in linear regression is reduced
to sum of squares in partial linear regression models.
Furthermore, we indicated that various sums of squares in the
linear regression are similar to different deviance statements in
partial linear regression. In addition to, coefficient of the
determination derived in linear regression model is easily
generalized to coefficient of the determination of the partial
linear regression model. For this aim, it is made two different
applications. A simulated and a real data set are considered to
prove the claim mentioned here. In this way, this study is
supported with a simulation and a real data example.
Abstract: MultiProtocol Label Switching (MPLS) is an
emerging technology that aims to address many of the existing issues
associated with packet forwarding in today-s Internetworking
environment. It provides a method of forwarding packets at a high
rate of speed by combining the speed and performance of Layer 2
with the scalability and IP intelligence of Layer 3. In a traditional IP
(Internet Protocol) routing network, a router analyzes the destination
IP address contained in the packet header. The router independently
determines the next hop for the packet using the destination IP
address and the interior gateway protocol. This process is repeated at
each hop to deliver the packet to its final destination. In contrast, in
the MPLS forwarding paradigm routers on the edge of the network
(label edge routers) attach labels to packets based on the forwarding
Equivalence class (FEC). Packets are then forwarded through the
MPLS domain, based on their associated FECs , through swapping
the labels by routers in the core of the network called label switch
routers. The act of simply swapping the label instead of referencing
the IP header of the packet in the routing table at each hop provides
a more efficient manner of forwarding packets, which in turn allows
the opportunity for traffic to be forwarded at tremendous speeds and
to have granular control over the path taken by a packet. This paper
deals with the process of MPLS forwarding mechanism,
implementation of MPLS datapath , and test results showing the
performance comparison of MPLS and IP routing. The discussion
will focus primarily on MPLS IP packet networks – by far the
most common application of MPLS today.
Abstract: The aim of this paper is to investigate a process of modernization of the People-s Republic of China. The theme of scientific research is interesting, first, because the Chinese model of development is recognized as successful and most dynamically developing. They are obliged by these successes of the modernization spent in the country. Economy modernization as the basic motive power of progress of the country is a priority direction of development in the Republic of Kazakhstan. So the example of successful development modernization processes in China can be rather useful to use in working out of the Kazakhstan national reforms.
Abstract: Basic ingredients of concrete are cement, fine aggregate, coarse aggregate and water. To produce a concrete of certain specific properties, optimum proportion of these ingredients are mixed. The important factors which govern the mix design are grade of concrete, type of cement and size, shape and grading of aggregates. Concrete mix design method is based on experimentally evolved empirical relationship between the factors in the choice of mix design. Basic draw backs of this method are that it does not produce desired strength, calculations are cumbersome and a number of tables are to be referred for arriving at trial mix proportion moreover, the variation in attainment of desired strength is uncertain below the target strength and may even fail. To solve this problem, a lot of cubes of standard grades were prepared and attained 28 days strength determined for different combination of cement, fine aggregate, coarse aggregate and water. An artificial neural network (ANN) was prepared using these data. The input of ANN were grade of concrete, type of cement, size, shape and grading of aggregates and output were proportions of various ingredients. With the help of these inputs and outputs, ANN was trained using feed forward back proportion model. Finally trained ANN was validated, it was seen that it gave the result with/ error of maximum 4 to 5%. Hence, specific type of concrete can be prepared from given material properties and proportions of these materials can be quickly evaluated using the proposed ANN.
Abstract: The sand production problem has led researchers into making various attempts to understand the phenomenon. The generally accepted concept is that the occurrence of sanding is due to the in-situ stress conditions and the induced changes in stress that results in the failure of the reservoir sandstone during hydrocarbon production from wellbores. By using a hypothetical cased (perforated) well, an approach to the problem is presented here by using Finite Element numerical modelling techniques. In addition to the examination of the erosion problem, the influence of certain key parameters is studied in order to ascertain their effect on the failure and subsequent erosion process. The major variables investigated include: drawdown, perforation depth, and the erosion criterion. Also included is the determination of the optimal mud pressure for given operational and reservoir conditions. The improved understanding between parameters enables the choice of optimal values to minimize sanding during oil production.