Abstract: This paper presents a method to support dynamic
packing in cases when no collision-free path can be found. The
method, which is primarily based on path planning and shrinking of
geometries, suggests a minimal geometry design change that results
in a collision-free assembly path. A supplementing approach to
optimize geometry design change with respect to redesign cost is
described. Supporting this dynamic packing method, a new method
to shrink geometry based on vertex translation, interweaved with
retriangulation, is suggested. The shrinking method requires neither
tetrahedralization nor calculation of medial axis and it preserves the
topology of the geometry, i.e. holes are neither lost nor introduced.
The proposed methods are successfully applied on industrial
geometries.
Abstract: Explosions may cause intensive damage to buildings
and sometimes lead to total and progressive destruction. Pressures
induced by explosions are one of the most destructive loads a
structure may experience. While designing structures for great
explosions may be expensive and impractical, engineers are looking
for methods for preventing destructions resulted from explosions. A
favorable structural system is a system which does not disrupt totally
due to local explosion, since such structures sustain less loss in
comparison with structural ones which really bear the load and
suddenly disrupt. Designing and establishing vital and necessary
installations in a way that it is resistant against direct hit of bomb and
rocket is not practical, economical, or expedient in many cases,
because the cost of construction and installation with such
specifications is several times more than the total cost of the related
equipment.
Abstract: The continuity in the electric supply of the electric installations is becoming one of the main requirements of the electric supply network (generation, transmission, and distribution of the electric energy). The achievement of this requirement depends from one side on the structure of the electric network and on the other side on the avaibility of the reserve source provided to maintain the supply in case of failure of the principal one. The avaibility of supply does not only depends on the reliability parameters of the both sources (principal and reserve) but it also depends on the reliability of the circuit breaker which plays the role of interlocking the reserve source in case of failure of the principal one. In addition, the principal source being under operation, its control can be ideal and sure, however, for the reserve source being in stop, a preventive maintenances which proceed on time intervals (periodicity) and for well defined lengths of time are envisaged, so that this source will always available in case of the principal source failure. The choice of the periodicity of preventive maintenance of the source of reserve influences directly the reliability of the electric feeder system In this work and on the basis of the semi- markovian's processes, the influence of the time of interlocking the reserve source upon the reliability of an industrial electric network is studied and is given the optimal time of interlocking the reserve source in case of failure the principal one, also the influence of the periodicity of the preventive maintenance of the source of reserve is studied and is given the optimal periodicity.
Abstract: The Aggregate Production Plan (APP) is a schedule of
the organization-s overall operations over a planning horizon to
satisfy demand while minimizing costs. It is the baseline for any
further planning and formulating the master production scheduling,
resources, capacity and raw material planning. This paper presents a
methodology to model the Aggregate Production Planning problem,
which is combinatorial in nature, when optimized with Genetic
Algorithms. This is done considering a multitude of constraints of
contradictory nature and the optimization criterion – overall cost,
made up of costs with production, work force, inventory, and
subcontracting. A case study of substantial size, used to develop the
model, is presented, along with the genetic operators.
Abstract: Matrix metalloproteinase-3 (MMP3) is key member
of the MMP family, and is known to be present in coronary
atherosclerotic. Several studies have demonstrated that MMP-3
5A/6A polymorphism modify each transcriptional activity in allele
specific manner. We hypothesized that this polymorphism may play
a role as risk factor for development of coronary stenosis. The aim of
our study was to estimate MMP-3 (5A/6A) gene polymorphism on
interindividual variability in risk for coronary stenosis in an Iranian
population.DNA was extracted from white blood cells and genotypes
were obtained from coronary stenosis cases (n=95) and controls
(n=100) by PCR (polymerase chain reaction) and restriction
fragment length polymorphism techniques. Significant differences
between cases and controls were observed for MMP3 genotype
frequencies (X2=199.305, p< 0.001); the 6A allele was less
frequently seen in the control group, compared to the disease group
(85.79 vs. 78%, 6A/6A+5A/6A vs. 5A/5A, P≤0.001). These data
imply the involvement of -1612 5A/6A polymorphism in coronary
stenosis, and suggest that probably the 6A/6A MMP-3 genotype is a
genetic susceptibility factor for coronary stenosis.
Abstract: Sociological models (e.g., social network analysis, small-group dynamic and gang models) have historically been used to predict the behavior of terrorist groups. However, they may not be the most appropriate method for understanding the behavior of terrorist organizations because the models were not initially intended to incorporate violent behavior of its subjects. Rather, models that incorporate life and death competition between subjects, i.e., models utilized by scientists to examine the behavior of wildlife populations, may provide a more accurate analysis. This paper suggests the use of biological models to attain a more robust method for understanding the behavior of terrorist organizations as compared to traditional methods. This study also describes how a biological population model incorporating predator-prey behavior factors can predict terrorist organizational recruitment behavior for the purpose of understanding the factors that govern the growth and decline of terrorist organizations. The Lotka-Volterra, a biological model that is based on a predator-prey relationship, is applied to a highly suggestive case study, that of the Irish Republican Army. This case study illuminates how a biological model can be utilized to understand the actions of a terrorist organization.
Abstract: Experiments have been carried out at sub-critical
Reynolds number to investigate free-to-roll motions induced by
forebody and/or wings complex flow on a 30° swept back nonslender
wings-slender body-model for static and dynamic (pitch-up)
cases. For the dynamic (pitch-up) case it has been observed that roll
amplitude decreases and lag increases with increase in pitching
speed. Decrease in roll amplitude with increase in pitch rate is
attributed to low disturbing rolling moment due to weaker interaction
between forebody and wing flow components. Asymmetric forebody
vortices dominate and control the roll motion of the model in
dynamic case when non-dimensional pitch rate ≥ 1x10-2.
Effectiveness of the active control scheme utilizing rotating nose with
artificial tip perturbation is observed to be low in the angle of attack
region where the complex flow over the wings has contributions from
both forebody and wings.
Abstract: This paper proposes a new solution to string matching problem. This solution constructs an inverted list representing a string pattern to be searched for. It then uses a new algorithm to process an input string in a single pass. The preprocessing phase takes 1) time complexity O(m) 2) space complexity O(1) where m is the length of pattern. The searching phase time complexity takes 1) O(m+α ) in average case 2) O(n/m) in the best case and 3) O(n) in the worst case, where α is the number of comparing leading to mismatch and n is the length of input text.
Abstract: The present work encounters the solution of the defect identification problem with the use of an evolutionary algorithm combined with a simplex method. In more details, a Matlab implementation of Genetic Algorithms is combined with a Simplex method in order to lead to the successful identification of the defect. The influence of the location and the orientation of the depressed ellipsoidal flaw was investigated as well as the use of different amount of static data in the cost function. The results were evaluated according to the ability of the simplex method to locate the global optimum in each test case. In this way, a clear impression regarding the performance of the novel combination of the optimization algorithms, and the influence of the geometrical parameters of the flaw in defect identification problems was obtained.
Abstract: The sustainability of a place depends on a series of factors which contribute to the quality of life, sense of place and recognition of identity. An activity like walking, which in itself is obviously ''sustainable'', can become non sustainable if the context in which it is carried out does not meet the conditions for an adequate quality of life. This work is aimed at proposing the analytical method of Place Maker to identify the elements that do not feature in traditional mapping and which constitute the contemporary identity of the places, and the relative complex map to represent those elements and support sustainable urban identity design. The method's potential for areas with a predominantly pedestrian vocation is illustrated by means of the case study of the Ramblas in Barcelona.
Abstract: This paper aims to (1) analyze the profiles of
transgressors (detected evaders); (2) examine reason(s) that triggered a
tax audit, causes of tax evasion, audit timeframe and tax penalty
charged; and (3) to assess if tax auditors followed the guidelines as
stated in the 'Tax Audit Framework' when conducting tax audits. In
2011, the Inland Revenue Board Malaysia (IRBM) had audited and
finalized 557 company cases. With official permission, data of all the
557 cases were obtained from the IRBM. Of these, a total of 421 cases
with complete information were analyzed. About 58.1% was small and
medium corporations and from the construction industry (32.8%). The
selection for tax audit was based on risk analysis (66.8%), information
from third party (11.1%), and firm with low profitability or fluctuating
profit pattern (7.8%). The three persistent causes of tax evasion by
firms were over claimed expenses (46.8%), fraudulent reporting of
income (38.5%) and overstating purchases (10.5%). These findings
are consistent with past literature. Results showed that tax auditors
took six to 18 months to close audit cases. More than half of tax
evaders were fined 45% on additional tax raised during audit for the
first offence. The study found tax auditors did follow the guidelines in
the 'Tax Audit Framework' in audit selection, settlement and penalty
imposition.
Abstract: This article experimentally investigates the
thermal performance of thermoelectric air-cooling module
which comprises a thermoelectric cooler (TEC) and an
air-cooling heat sink. The influences of input current and heat
load are determined. And performances under each situation
are quantified by thermal resistance analysis. Since TEC
generates Joule heat, this nature makes construction of thermal
resistance network difficult. To simplify the analysis, this
article emphasizes on the resistance heat load might meet when
passing through the device. Therefore, the thermal resistances
in this paper are to divide temperature differences by heat load.
According to the result, there exists an optimum input current
under every heating power. In this case, the optimum input
current is around 6A or 7A. The performance of the heat sink
would be improved with TEC under certain heating power and
input current, especially at a low heat load. According to the
result, the device can even make the heat source cooler than the
ambient. However, TEC is not always effective at every heat
load and input current. In some situation, the device works
worse than the heat sink without TEC. To determine the
availability of TEC, this study figures out the effective
operating region in which the TEC air-cooling module works
better than the heat sink without TEC. The result shows that
TEC is more effective at a lower heat load. If heat load is too
high, heat sink with TEC will perform worse than without TEC.
The limit of this device is 57W. Besides, TEC is not helpful if
input current is too high or too low. There is an effective range
of input current, and the range becomes narrower when the heat
load grows.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: Available Bit Rate Service (ABR) is the lower priority
service and the better service for the transmission of data. On wireline
ATM networks ABR source is always getting the feedback from
switches about increase or decrease of bandwidth according to the
changing network conditions and minimum bandwidth is guaranteed.
In wireless networks guaranteeing the minimum bandwidth is really a
challenging task as the source is always in mobile and traveling from
one cell to another cell. Re establishment of virtual circuits from start
to end every time causes the delay in transmission. In our proposed
solution we proposed the mechanism to provide more available
bandwidth to the ABR source by re-usage of part of old Virtual
Channels and establishing the new ones. We want the ABR source to
transmit the data continuously (non-stop) inorderto avoid the delay.
In worst case scenario at least minimum bandwidth is to be allocated.
In order to keep the data flow continuously, priority is given to the
handoff ABR call against new ABR call.
Abstract: Logistics outsourcing is a growing trend and measuring its performance, a challenge. It must be consistent with the objectives set for logistics outsourcing, but we have found no objective-based performance measurement system. We have conducted a comprehensive review of the specialist literature to cover this gap, which has led us to identify and define these objectives. The outcome is that we have obtained a list of the most relevant objectives and their descriptions. This will enable us to analyse in a future study whether the indicators used for measuring logistics outsourcing performance are consistent with the objectives pursued with the outsourcing. If this is not the case, a proposal will be made for a set of financial and operational indicators to measure performance in logistics outsourcing that take the goals being pursued into account.
Abstract: In Algeria, liberalization reforms undertaken since the 1990s have resulted in negative effects on the development and management of irrigation schemes, as well as on the conditions of farmers. Reforms have been undertaken to improve the performance of irrigation schemes, such as the national plan of agricultural development (PNDA) in 2000 and the water pricing policy of 2005. However, after implementation of these policies, questions have arisen with regard to irrigation performance and its suitability for agricultural development. Hence, the aim of this paper is to provide insight into the profitability of irrigation during the transition period under current irrigation agricultural policies in Algeria. By using the method of farm crop budget analysis in the East Mitidja irrigation scheme, the returns from using surface water resources based on farm typology were found to vary among crops and farmers- groups within the scheme. Irrigation under the current situation is profitable for all farmers, including both those who benefit from subsidies and those who do not. However, the returns to water were found to be very sensitive to crop price fluctuations, particularly for non-subsidized groups and less so for those whose farming is based on orchards. Moreover, the socio-economic environment of the farmers contributed to less significant impacts of the PNDA policy. In fact, the limiting factor is not only the water, but also the lack of land ownership title. Market access constraints led to less agricultural investment and therefore to low intensification and low water productivity. It is financially feasible to recover the annual O&M costs in the irrigation scheme. By comparing the irrigation water price, returns to water, and O&M costs of water delivery, it is clear that irrigation can be profitable in the future. However, water productivity must be improved by enhancing farmers- income through farming investment, improving assets access, and the allocation of activities and crops which bring high returns to water; this could allow the farmers to pay more for water and allow cost recovery for water systems.
Abstract: The healthcare environment is generally perceived as
being information rich yet knowledge poor. However, there is a lack
of effective analysis tools to discover hidden relationships and trends
in data. In fact, valuable knowledge can be discovered from
application of data mining techniques in healthcare system. In this
study, a proficient methodology for the extraction of significant
patterns from the Coronary Heart Disease warehouses for heart
attack prediction, which unfortunately continues to be a leading cause
of mortality in the whole world, has been presented. For this purpose,
we propose to enumerate dynamically the optimal subsets of the
reduced features of high interest by using rough sets technique
associated to dynamic programming. Therefore, we propose to
validate the classification using Random Forest (RF) decision tree to
identify the risky heart disease cases. This work is based on a large
amount of data collected from several clinical institutions based on
the medical profile of patient. Moreover, the experts- knowledge in
this field has been taken into consideration in order to define the
disease, its risk factors, and to establish significant knowledge
relationships among the medical factors. A computer-aided system is
developed for this purpose based on a population of 525 adults. The
performance of the proposed model is analyzed and evaluated based
on set of benchmark techniques applied in this classification problem.
Abstract: Experimental data from an atmospheric air/water terrain slugging case has been made available by the Shell Amsterdam research center, and has been subject to numerical simulation and comparison with a one-dimensional two-phase slug tracking simulator under development at the Norwegian University of Science and Technology. The code is based on tracking of liquid slugs in pipelines by use of a Lagrangian grid formulation implemented in Cµ by use of object oriented techniques. An existing hybrid spatial discretization scheme is tested, in which the stratified regions are modelled by the two-fluid model. The slug regions are treated incompressible, thus requiring a single momentum balance over the whole slug. Upon comparison with the experimental data, the period of the simulated severe slugging cycle is observed to be sensitive to slug generation in the horizontal parts of the system. Two different slug initiation methods have been tested with the slug tracking code, and grid dependency has been investigated.
Abstract: The review performed on the condition of energy
consumption & rate in Iran, shows that unfortunately the subject of
optimization and conservation of energy in active industries of
country lacks a practical & effective method and in most factories,
the energy consumption and rate is more than in similar industries of
industrial countries. The increasing demand of electrical energy and
the overheads which it imposes on the organization, forces
companies to search for suitable approaches to optimize energy
consumption and demand management. Application of value
engineering techniques is among these approaches. Value
engineering is considered a powerful tool for improving profitability.
These tools are used for reduction of expenses, increasing profits,
quality improvement, increasing market share, performing works in
shorter durations, more efficient utilization of sources & etc.
In this article, we shall review the subject of value engineering and
its capabilities for creating effective transformations in industrial
organizations, in order to reduce energy costs & the results have
been investigated and described during a case study in Mazandaran
wood and paper industries, the biggest consumer of energy in north
of Iran, for the purpose of presenting the effects of performed tasks
in optimization of energy consumption by utilizing value engineering
techniques in one case study.
Abstract: It is impossible to think about democracy without elections. The litmus test of any electoral process in any country is the possibility of a one time minority to become a majority at another time and a peaceful transition of power. In many countries in Sub-Saharan Africa though the multi-party elections appeared to be competitive they failed the acid test of democracy: peaceful regime change in a free and fair election. Failure to solve electoral disputes might lead to bloody electoral conflicts as witnessed in many emerging democracies in Africa. The aim of this paper is to investigate electoral conflicts in Africa since the end of the Cold War by using the 2005 post-election violence in Ethiopia as a case study. In Ethiopia, the coming to power of the EPRDF in 1991 marked the fall of the Derg dictatorial military government and the beginning of a multi-party democracy. The country held multi-party parliamentary elections in 1995, 2000, and 2005 where the ruling EPRDF party “won" the elections through violence, involving intimidation, manipulation, detentions of political opponents, torture, and political assassinations. The 2005 electoral violence was the worst electoral violence in the country-s political history that led to the death of 193 protestors and the imprisonment of more than 40, 000 people. It is found out that the major causes of the 2005 Ethiopian election were the defeat of the ruling party in the election and its attempt to reverse the poll results by force; the Opposition-s lack of decisive leadership; the absence of independent courts and independent electoral management body; and the ruling party-s direct control over the army and police.