Abstract: The reheating furnace is used to reheat the steel slabs
before the hot-rolling process. The supported system includes the
stationary/moving beams, and the skid buttons which block some
thermal radiation transmitted to the bottom of the slabs. Therefore, it is
important to analyze the steel slab temperature distribution during the
heating period. A three-dimensional mathematical transient heat
transfer model for the prediction of temperature distribution within the
slab has been developed. The effects of different skid button height
(H=60mm, 90mm, and 120mm) and different gap distance between
two slabs (S=50mm, 75mm, and 100mm) on the slab skid mark
formation and temperature profiles are investigated. Comparison with
the in-situ experimental data from Steel Company in Taiwan shows
that the present heat transfer model works well for the prediction of
thermal behavior of the slab in the reheating furnace. It is found that
the skid mark severity decreases with an increase in the skid button
height. The effect of gap distance is important only for the slab edge
planes, while it is insignificant for the slab central planes.
Abstract: A large variety of pipe flange is required in marine
and construction industry. Pipe flanges are usually welded or screwed
to the pipe end and are connected with bolts. This approach is very
simple and widely used for a long time; however, it results in high
development cost and low productivity, and the productions made by
this approach usually have safety problem at the welding area. In this
research, a new approach of forming pipe flange based on cold
forging and floating die concept is presented. This innovative
approach increases the effectiveness of the material usage and save
the time cost compared with conventional welding method. To ensure the dimensional accuracy of the final product, the finite
element analysis (FEA) was carried out to simulate the process of
cold forging, and the orthogonal experiment methods were used to
investigate the influence of four manufacturing factors (pin die angle,
pipe flange angle, rpm, pin die distance from clamp jig) and predicted
the best combination of them. The manufacturing factors were
obtained by numerical and experimental studies and it shows that the
approach is very useful and effective for the forming of pipe flange,
and can be widely used later.
Abstract: In this paper, we present a comparative study of three
methods of 2D face recognition system such as: Iso-Geodesic Curves
(IGC), Geodesic Distance (GD) and Geodesic-Intensity Histogram
(GIH). These approaches are based on computing of geodesic
distance between points of facial surface and between facial curves.
In this study we represented the image at gray level as a 2D surface in
a 3D space, with the third coordinate proportional to the intensity
values of pixels. In the classifying step, we use: Neural Networks
(NN), K-Nearest Neighbor (KNN) and Support Vector Machines
(SVM). The images used in our experiments are from two wellknown
databases of face images ORL and YaleB. ORL data base was
used to evaluate the performance of methods under conditions where
the pose and sample size are varied, and the database YaleB was used
to examine the performance of the systems when the facial
expressions and lighting are varied.
Abstract: This paper aims to determine Fundamental Natural
Frequency (FNF) of a structural composite floor system known as
Chromite. To achieve this purpose, FNFs of studied panels are
determined by development of Finite Element Models (FEMs) in
ABAQUS program. American Institute of Steel Construction (AISC)
code in Steel Design Guide Series 11 presents a fundamental formula
to calculate FNF of a steel framed floor system. This formula has
been used to verify results of the FEMs. The variability in the FNF of
the studied system under various parameters such as dimensions of
floor, boundary conditions, rigidity of main and secondary beams
around the floor, thickness of concrete slab, height of composite
joists, distance between composite joists, thickness of top and bottom
flanges of the open web steel joists, and adding tie beam
perpendicular on the composite joists, is determined. The results
show that changing in dimensions of the system, its boundary
conditions, rigidity of main beam, and also adding tie beam,
significant changes the FNF of the system up to 452.9%, 50.8%, -
52.2%, %52.6%, respectively. In addition, increasing thickness of
concrete slab increases the FNF of the system up to 10.8%.
Furthermore, the results demonstrate that variation in rigidity of
secondary beam, height of composite joist, and distance between
composite joists, and thickness of top and bottom flanges of open
web steel joists insignificant changes the FNF of the studied system
up to -0.02%, -3%, -6.1%, and 0.96%, respectively. Finally, the
results of this study help designer predict occurrence of resonance,
comfortableness, and design criteria of the studied system.
Abstract: The Portuguese footwear industry had in the last five years a remarkable performance in the exportation values, the trade balance and others economic indicators. After a long period of difficulties and with a strong reduction of companies and employees since 1994 until 2009, the Portuguese footwear industry changed the strategy and is now a success case between the international players of footwear. Only the Italian industry sells footwear with a higher value than the Portuguese and the distance between them is decreasing year by year. This paper analyses how the Portuguese footwear companies innovate and make innovation, according the classification proposed by the Oslo Manual. Also, analyses the strategy follow in the innovation process and shows the linkage between the type of innovation and the strategy of innovation. The research methodology was qualitative and the strategy for data collection was the case study. The qualitative data will be analyzed with the MAXQDA software. The economic results of the footwear companies studied shows differences between all of them and these differences are related with the innovation strategy adopted. The companies focused in product and marketing innovation, oriented to their target market, have higher ratios “turnover per worker” than the companies focused in process innovation. However, all the footwear companies in this “low-tech” industry create value and contribute to a positive foreign trade of 1.310 million euros in 2013. The growth strategies implemented has the participation of the sectorial organizations in several innovative projects. And it’s obvious that cooperation between all of them is a critical element to the performance achieved by the companies and the innovation observed. The Portuguese footwear sector has in the last years an excellent performance (economic results, exportation values, trade balance, brands and international image) and his performance is strongly related with the strategy in innovation followed, the type of innovation and the networks in the cluster. A simplified model, called “Ace of Diamonds”, is proposed by the authors and explains the way how this performance was reached by the seven companies that participate in the study (two of them are the leaders in the setor), and if this model can be used in others traditional and “low-tech” industries.
Abstract: A Mobile Adhoc Network (MANET) is a collection of mobile nodes that communicate with each other with wireless links and without pre-existing communication infrastructure. Routing is an important issue which impacts network performance. As MANETs lack central administration and prior organization, their security concerns are different from those of conventional networks. Wireless links make MANETs susceptible to attacks. This study proposes a new trust mechanism to mitigate wormhole attack in MANETs. Different optimization techniques find available optimal path from source to destination. This study extends trust and reputation to an improved link quality and channel utilization based Adhoc Ondemand Multipath Distance Vector (AOMDV). Differential Evolution (DE) is used for optimization.
Abstract: Networked environments which provide platforms for
business organizations are configured in different forms depending
on many factors including life time, member characteristics,
communication structure, and business objectives, among others.
With continuing advances in digital technologies the distance has
become a less barrier for business minded collaboration among
organizations. With the need and ease to make business collaborate
nowadays organizations are sometimes forced to co-work with others
that are either unknown or less known to them in terms of history and
performance. A promising approach for sustaining established
collaboration has been establishment of trust relationship among
organizations based on assessed trustworthiness for each participating
organization. It has been stated in research that trust in organization is
dynamic and thus assessment of trust level must address such
dynamic nature. This paper assesses relevant aspects of trust and
applies the assessed concepts to propose a semi-automated system for
the management of Sustainability and Evolution of trust in
organizations participating in specific objective in a networked
organizations environment.
Abstract: MHD chemically reacting viscous fluid flow towards
a vertical surface with slip and convective boundary conditions has
been conducted. The temperature and the chemical species
concentration of the surface and the velocity of the external flow are
assumed to vary linearly with the distance from the vertical surface.
The governing differential equations are modeled and transformed
into systems of ordinary differential equations, which are then solved
numerically by a shooting method. The effects of various parameters
on the heat and mass transfer characteristics are discussed. Graphical
results are presented for the velocity, temperature, and concentration
profiles whilst the skin-friction coefficient and the rate of heat and
mass transfers near the surface are presented in tables and discussed.
The results revealed that increasing the strength of the magnetic field
increases the skin-friction coefficient and the rate of heat and mass
transfers toward the surface. The velocity profiles are increased
towards the surface due to the presence of the Lorenz force, which
attracts the fluid particles near the surface. The rate of chemical
reaction is seen to decrease the concentration boundary layer near the
surface due to the destructive chemical reaction occurring near the
surface.
Abstract: A multilayer passive shield composed of low-activity
lead (Pb), copper (Cu), tin (Sn) and iron (Fe) was designed and
manufactured for a coaxial HPGe detector placed at a surface
laboratory for reducing background radiation and radiation dose to
the personnel. The performance of the shield was evaluated and
efficiency curves of the detector were plotted by using of various
standard sources in different distances. Monte Carlo simulations and
a set of TLD chips were used for dose estimation in two distances of
20 and 40 cm. The results show that the shield reduced background
spectrum and the personnel dose more than 95%.
Abstract: In this study, electric field distribution analyses for
three pylon models are carried out by a Finite Element Method
(FEM) based software. Analyses are performed in both stationary and
time domains to observe instantaneous values along with the
effective ones. Considering the results of the study, different line
geometries is considerably affecting the magnitude and distribution
of electric field although the line voltages are the same. Furthermore,
it is observed that maximum values of instantaneous electric field
obtained in time domain analysis are quite higher than the effective
ones in stationary mode. In consequence, electric field distribution
analyses should be individually made for each different line model
and the limit exposure values or distances to residential buildings
should be defined according to the results obtained.
Abstract: Sewer deposits have been identified as a major cause
of dysfunctions in combined sewer systems regarding sewer
management, which induces different negative consequents resulting
in poor hydraulic conveyance, environmental damages as well as
worker’s health. In order to overcome the problematics of
sedimentation, flushing has been considered as the most operative
and cost-effective way to minimize the sediments impacts and
prevent such challenges. Flushing, by prompting turbulent wave
effects, can modify the bed form depending on the hydraulic
properties and geometrical characteristics of the conduit. So far, the
dynamics of the bed-load during high-flow events in combined sewer
systems as a complex environment is not well understood, mostly due
to lack of measuring devices capable to work in the “hostile” in
combined sewer system correctly. In this regards, a one-episode
flushing issue from an opening gate valve with weir function was
carried out in a trunk sewer in Paris to understand its cleansing
efficiency on the sediments (thickness: 0-30 cm). During more than
1h of flushing within 5 m distance in downstream of this flushing
device, a maximum flowrate and a maximum level of water have
been recorded at 5 m in downstream of the gate as 4.1 m3/s and 2.1
m respectively. This paper is aimed to evaluate the efficiency of this
type of gate for around 1.1 km (from the point -50 m to +1050 m in
downstream from the gate) by (i) determining bed grain-size
distribution and sediments evolution through the sewer channel, as
well as their organic matter content, and (ii) identifying sections that
exhibit more changes in their texture after the flush. For the first one,
two series of sampling were taken from the sewer length and then
analyzed in laboratory, one before flushing and second after, at same
points among the sewer channel. Hence, a non-intrusive sampling
instrument has undertaken to extract the sediments smaller than the
fine gravels. The comparison between sediments texture after the
flush operation and the initial state, revealed the most modified zones
by the flush effect, regarding the sewer invert slope and hydraulic
parameters in the zone up to 400 m from the gate. At this distance,
despite the increase of sediment grain-size rages, D50 (median grainsize)
varies between 0.6 mm and 1.1 mm compared to 0.8 mm and 10
mm before and after flushing, respectively. Overall, regarding the
sewer channel invert slope, results indicate that grains smaller than
sands (< 2 mm) are more transported to downstream along about 400
m from the gate: in average 69% before against 38% after the flush
with more dispersion of grain-sizes distributions. Furthermore, high
effect of the channel bed irregularities on the bed material evolution
has been observed after the flush.
Abstract: This study integrates a larger research empirical
project that examines second language (SL) learners’ profiles and
valid procedures to perform complete and diagnostic assessment in
schools. 102 learners of Portuguese as a SL aged 7 and 17 years
speakers of distinct home languages were assessed in several
linguistic tasks. In this article, we focused on writing performance in
the specific task of narrative essay composition. The written outputs
were measured using the score in six components adapted from an
English SL assessment context (Alberta Education): linguistic
vocabulary, grammar, syntax, strategy, socio-linguistic, and
discourse. The writing processes and strategies in Portuguese
language used by different immigrant students were analysed to
determine features and diversity of deficits on authentic texts
performed by SL writers. Differentiated performance was based on
the diversity of the following variables: grades, previous schooling,
home language, instruction in first language, and exposure to
Portuguese as Second Language. Indo-Aryan languages speakers
showed low writing scores compared to their peers and the type of
language and respective cognitive mapping (such as Mandarin and
Arabic) was the predictor, not linguistic distance. Home language
instruction should also be prominently considered in further research
to understand specificities of cognitive academic profile in a
Romance languages learning context. Additionally, this study also
examined the teachers’ representations that will be here addressed to
understand educational implications of second language teaching in
psychological distress of different minorities in schools of specific
host countries.
Abstract: Indonesia has experienced annual forest fires that have
rapidly destroyed and degraded its forests. Fires in the peat swamp
forests of Riau Province, have set the stage for problems to worsen,
this being the ecosystem most prone to fires (which are also the most
difficult, to extinguish). Despite various efforts to curb deforestation,
and forest degradation processes, severe forest fires are still
occurring. To find an effective solution, the basic causes of the
problems must be identified. It is therefore critical to have an indepth
understanding of the underlying causal factors that have
contributed to deforestation and forest degradation as a whole, in
order to attain reductions in their rates. An assessment of the drivers of deforestation and forest
degradation was carried out, in order to design and implement
measures that could slow these destructive processes. Research was
conducted in Giam Siak Kecil–Bukit Batu Biosphere Reserve
(GSKBB BR), in the Riau Province of Sumatera, Indonesia. A
biosphere reserve was selected as the study site because such reserves
aim to reconcile conservation with sustainable development. A
biosphere reserve should promote a range of local human activities,
together with development values that are in line spatially and
economically with the area conservation values, through use of a
zoning system. Moreover, GSKBB BR is an area with vast peatlands,
and is experiencing forest fires annually. Various factors were
analysed to assess the drivers of deforestation and forest degradation
in GSKBB BR; data were collected from focus group discussions
with stakeholders, key informant interviews with key stakeholders,
field observation and a literature review. Landsat satellite imagery was used to map forest-cover changes
for various periods. Analysis of landsat images, taken during the
period 2010-2014, revealed that within the non-protected area of core
zone, there was a trend towards decreasing peat swamp forest areas,
increasing land clearance, and increasing areas of community oilpalm
and rubber plantations. Fire was used for land clearing and most
of the forest fires occurred in the most populous area (the transition
area). The study found a relationship between the deforested/
degraded areas, and certain distance variables, i.e. distance from
roads, villages and the borders between the core area and the buffer
zone. The further the distance from the core area of the reserve, the
higher was the degree of deforestation and forest degradation. Research findings suggested that agricultural expansion may be
the direct cause of deforestation and forest degradation in the reserve,
whereas socio-economic factors were the underlying driver of forest
cover changes; such factors consisting of a combination of sociocultural,
infrastructural, technological, institutional (policy and governance), demographic (population pressure) and economic
(market demand) considerations. These findings indicated that local
factors/problems were the critical causes of deforestation and
degradation in GSKBB BR. This research therefore concluded that
reductions in deforestation and forest degradation in GSKBB BR
could be achieved through ‘local actor’-tailored approaches such as
community empowerment.
Abstract: Localization of nodes is one of the key issues of
Wireless Sensor Network (WSN) that gained a wide attention in
recent years. The existing localization techniques can be generally
categorized into two types: range-based and range-free. Compared
with rang-based schemes, the range-free schemes are more costeffective,
because no additional ranging devices are needed. As a
result, we focus our research on the range-free schemes. In this paper
we study three types of range-free location algorithms to compare the
localization error and energy consumption of each one. Centroid
algorithm requires a normal node has at least three neighbor anchors,
while DV-hop algorithm doesn’t have this requirement. The third
studied algorithm is the amorphous algorithm similar to DV-Hop
algorithm, and the idea is to calculate the hop distance between two
nodes instead of the linear distance between them. The simulation
results show that the localization accuracy of the amorphous
algorithm is higher than that of other algorithms and the energy
consumption does not increase too much.
Abstract: Singular value decomposition based optimisation of
geometric design parameters of a 5-speed gearbox is studied. During
the optimisation, a four-degree-of freedom torsional vibration model
of the pinion gear-wheel gear system is obtained and the minimum
singular value of the transfer matrix is considered as the objective
functions. The computational cost of the associated singular value
problems is quite low for the objective function, because it is only
necessary to compute the largest and smallest singular values (μmax
and μmin) that can be achieved by using selective eigenvalue solvers;
the other singular values are not needed. The design parameters are
optimised under several constraints that include bending stress,
contact stress and constant distance between gear centres. Thus, by
optimising the geometric parameters of the gearbox such as, the
module, number of teeth and face width it is possible to obtain a
light-weight-gearbox structure. It is concluded that the all optimised
geometric design parameters also satisfy all constraints.
Abstract: In this paper, we provided a literature survey on the
artificial stock problem (ASM). The paper began by exploring the
complexity of the stock market and the needs for ASM. ASM
aims to investigate the link between individual behaviors (micro
level) and financial market dynamics (macro level). The variety of
patterns at the macro level is a function of the AFM complexity. The
financial market system is a complex system where the relationship
between the micro and macro level cannot be captured analytically.
Computational approaches, such as simulation, are expected to
comprehend this connection. Agent-based simulation is a simulation
technique commonly used to build AFMs. The paper proceeds by
discussing the components of the ASM. We consider the roles
of behavioral finance (BF) alongside the traditionally risk-averse
assumption in the construction of agent’s attributes. Also, the
influence of social networks in the developing of agents interactions is
addressed. Network topologies such as a small world, distance-based,
and scale-free networks may be utilized to outline economic
collaborations. In addition, the primary methods for developing
agents learning and adaptive abilities have been summarized.
These incorporated approach such as Genetic Algorithm, Genetic
Programming, Artificial neural network and Reinforcement Learning.
In addition, the most common statistical properties (the stylized facts)
of stock that are used for calibration and validation of ASM are
discussed. Besides, we have reviewed the major related previous
studies and categorize the utilized approaches as a part of these
studies. Finally, research directions and potential research questions
are argued. The research directions of ASM may focus on the macro
level by analyzing the market dynamic or on the micro level by
investigating the wealth distributions of the agents.
Abstract: Mobile Adhoc Networks (MANETs) are
infrastructure-less, dynamic network of collections of wireless mobile
nodes communicating with each other without any centralized
authority. A MANET is a mobile device of interconnections through
wireless links, forming a dynamic topology. Routing protocols have a
big role in data transmission across a network. Routing protocols,
two major classifications are unipath and multipath. This study
evaluates performance of an on-demand multipath routing protocol
named Adhoc On-demand Multipath Distance Vector routing
(AOMDV). This study proposes Energy Aware AOMDV (EAAOMDV)
an extension of AOMDV which decreases energy
consumed on a route.
Abstract: The output error of the globoidal cam mechanism can
be considered as a relevant indicator of mechanism performance,
because it determines kinematic and dynamical behavior of
mechanical transmission. Based on the differential geometry and the
rigid body transformations, the mathematical model of surface
geometry of the globoidal cam is established. Then we present the
analytical expression of the output error (including the transmission
error and the displacement error along the output axis) by considering
different manufacture and assembly errors. The effects of the center
distance error, the perpendicular error between input and output axes
and the rotational angle error of the globoidal cam on the output error
are systematically analyzed. A globoidal cam mechanism which is
widely used in automatic tool changer of CNC machines is applied for
illustration. Our results show that the perpendicular error and the
rotational angle error have little effects on the transmission error but
have great effects on the displacement error along the output axis. This
study plays an important role in the design, manufacture and assembly
of the globoidal cam mechanism.
Abstract: This paper will seek to clarify important key terms
such as home schooling and home education as well as the legalities
attached to such terms. It will reflect on the recent proposed changes
to terminology in NSW, Australia. The various pedagogical
approaches to home education will be explored including their
prominence in the Australian context. There is a strong focus on
literature from Australia. The historical background of home
education in Australia will be explained as well as the difference
between distance education and home education. The future of home
education in Australia will be discussed.
Abstract: In the cooperative transmission scheme, both the
cellular system and broadcasting system are composed. Two cellular
base stations (CBSs) communicating with a user in the cell edge use
cooperative transmission scheme in the conventional scheme. In the
case that the distance between two CBSs and the user is distant, the
conventional scheme does not guarantee the quality of the
communication because the channel condition is bad. Therefore, if the
distance between CBSs and a user is distant, the performance of the
conventional scheme is decreased. Also, the bad channel condition has
bad effects on the performance. The proposed scheme uses two relays
to communicate well with CBSs when the channel condition between
CBSs and the user is poor. Using the relay in the high attenuation
environment can obtain both advantages of the high bit error rate
(BER) and throughput performance.