Abstract: The aim of this study is to develop mathematical
relationships for the performance parameter brake thermal efficiency
(BTE) and emission parameter nitrogen oxides (NOx) for the various
esters of vegetable oils used as CI engine fuel. The BTE is an
important performance parameter defining the ability of engine to
utilize the energy supplied and power developed similarly it is
indication of efficiency of fuels used. The esters of cottonseed oil,
soybean oil, jatropha oil and hingan oil are prepared using
transesterification process and characterized for their physical and
main fuel properties including viscosity, density, flash point and
higher heating value using standard test methods. These esters are
tried as CI engine fuel to analyze the performance and emission
parameters in comparison to diesel. The results of the study indicate
that esters as a fuel does not differ greatly with that of diesel in
properties. The CI engine performance with esters as fuel is in line
with the diesel where as the emission parameters are reduced with the
use of esters.
The correlation developed between BTE and brake power(BP),
gross calorific value(CV), air-fuel ratio(A/F), heat carried away by
cooling water(HCW). Another equation is developed between the
NOx emission and CO, HC, smoke density (SD), exhaust gas
temperature (EGT). The equations are verified by comparing the
observed and calculated values which gives the coefficient of
correlation of 0.99 and 0.96 for the BTE and NOx equations
respectively.
Abstract: In this work we study the effect of several covariates X on a censored response variable T with unknown probability distribution. In this context, most of the studies in the literature can be located in two possible general classes of regression models: models that study the effect the covariates have on the hazard function; and models that study the effect the covariates have on the censored response variable. Proposals in this paper are in the second class of models and, more specifically, on least squares based model approach. Thus, using the bootstrap estimate of the bias, we try to improve the estimation of the regression parameters by reducing their bias, for small sample sizes. Simulation results presented in the paper show that, for reasonable sample sizes and censoring levels, the bias is always smaller for the new proposals.
Abstract: We integrate TiN/Ni/HfO2/Si RRAM cell with a
vertical gate-all-around (GAA) nanowire transistor to achieve
compact 4F2 footprint in a 1T1R configuration. The tip of the Si
nanowire (source of the transistor) serves as bottom electrode of the
memory cell. Fabricated devices with nanowire diameter ~ 50nm
demonstrate ultra-low current/power switching; unipolar switching
with 10μA/30μW SET and 20μA/30μW RESET and bipolar switching
with 20nA/85nW SET and 0.2nA/0.7nW RESET. Further, the
switching current is found to scale with nanowire diameter making the
architecture promising for future scaling.
Abstract: This paper details a new concept of using compressed air as a potential zero pollution power source for motorbikes. In place of an internal combustion engine, the motorbike is equipped with an air turbine transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor diameters, casing diameters and ratio of rotor to casing diameters of the turbine have been considered and analyzed. It is concluded that the work output is found optimum for some typical values of rotor / casing diameter ratios. In this study, the maximum power works out to 3.825 kW (5.20 HP) for casing diameter of 200 mm and rotor to casing diameter ratio of 0.65 to 0.60 which is sufficient to run motorbike.
Abstract: An electrical apparatus for measuring moisture
content was developed by our laboratory and uses dependence of
electrical properties on water content in studied material. Error
analysis of the apparatus was run by measuring different volumes of
water in a simplified specimen, i.e. hollow plexiglass block, in order
to avoid as many side-effects as possible. Obtained data were
processed using both basic and advanced statistics and results were
compared with each other. The influence of water content on
accuracy of measured data was studied as well as the influence of
variation of apparatus' proper arrangement or factual methodics of its
usage. The overall coefficient of variation was 4%. There was no
trend found in results of error dependence on water content.
Comparison with current surveys led to a conclusion, that the studied
apparatus can be used for indirect measurement of water content in
porous materials, with expectable error and under known conditions.
Factual experiments with porous materials are not involved, but are
currently under investigation.
Abstract: Phase transformation temperature is one of the most important parameters for the shape memory alloys (SMAs). The most popular method to determine these phase transformation temperatures is the Differential Scanning Calorimeter (DSC), but due to the limitation of the DSC testing itself, it made it difficult for the finished product which is not in the powder form. A novel method which uses the Universal Testing Machine has been conducted to determine the phase transformation temperatures. The Flexinol wire was applied with force and maintained throughout the experiment and at the same time it was heated up slowly until a temperature of approximately 1000C with direct current. The direct current was then slowly decreased to cool down the temperature of the Flexinol wire. All the phase transformation temperatures for Flexinol wire were obtained. The austenite start at 52.540C and austenite finish at 60.900C, while martensite start at 44.780C and martensite finish at 32.840C.
Abstract: The aim of this studywas toinvestigate the effect
ofrunning classification (sprint, middle, and long distance)and two
distances on blood lactate (BLa), heart rate (HR), and rating of
perceived exertion (RPE) Borg scale ratings in collegiate athletes. On
different days, runners (n = 15) ran 400m and 1600m at a five min
mile pace, followed by a two min 6mph jog, and a two min 3mph
walk as part of the cool down. BLa, HR, and RPE were taken at
baseline, post-run, plus 2 and 4 min recovery times. The middle and
long distance runners exhibited lower BLa concentrations than sprint
runners after two min of recovery post 400 m runs, immediately after,
and two and four min recovery periods post 1600 m runs. When
compared to sprint runners, distance runners may have exhibited the
ability to clear BLa more quickly, particularly after running 1600 m.
Abstract: We investigated a modified thermal evaporation
method in the growth process of ZnO nanowires. ZnO nanowires
were fabricated on p-type silicon substrates without using a metal
catalyst. A simple horizontal double-tube system along with
chemical vapor diffusion of the precursor was used to grow the ZnO
nanowires. The substrates were placed in different temperature
zones, and ZnO nanowires with different diameters were obtained for
the different substrate temperatures. In addition to the nanowires,
ZnO microdiscs with different diameters were obtained on another
substrate, which was placed at a lower temperature than the other
substrates. The optical properties and crystalline quality of the ZnO
nanowires and microdiscs were characterized by room temperature
photoluminescence (PL) and Raman spectrometers. The PL and
Raman studies demonstrated that the ZnO nanowires and microdiscs
grown using such set-up had good crystallinity with excellent optical
properties. Rectifying behavior of ZnO/Si heterostructures was
characterized by a simple DC circuit.
Abstract: In this paper, an approach for finding optimized
layouts for connecting PV units delivering maximum array output
power is suggested. The approach is based on considering the
different varying parameters of PV units that might be extracted from
a general two-diode model. These are mainly, solar irradiation,
reverse saturation currents, ideality factors, series and shunt
resistances in addition to operating temperature. The approach has
been tested on 19 possible 2×3 configurations and allowed to
determine the optimized configurations as well as examine the effects
of the different units- parameters on the maximum output power.
Thus, using this approach, standard arrays with n×m units can be
configured for maximum generated power and allows designing PV
based systems having reduced surfaces to fit specific required power,
as it is the case for solar cars and other mobile systems.
Abstract: In this study three commercial semiconductor devices
were characterized in the laboratory for computed tomography
dosimetry: one photodiode and two phototransistors. It was evaluated
four responses to the irradiation: dose linearity, energy dependence,
angular dependence and loss of sensitivity after X ray exposure. The
results showed that the three devices have proportional response with
the air kerma; the energy dependence displayed for each device
suggests that some calibration factors would be applied for each one;
the angular dependence showed a similar pattern among the three
electronic components. In respect to the fourth parameter analyzed,
one phototransistor has the highest sensitivity however it also showed
the greatest loss of sensitivity with the accumulated dose. The
photodiode was the device with the smaller sensitivity to radiation,
on the other hand, the loss of sensitivity after irradiation is negligible.
Since high accuracy is a desired feature for a dosimeter, the
photodiode can be the most suitable of the three devices for
dosimetry in tomography. The phototransistors can also be used for
CT dosimetry, however it would be necessary a correction factor due
to loss of sensitivity with accumulated dose.
Abstract: The aim of this paper is to investigate twodimensional unsteady flow of a viscous incompressible fluid about stagnation point on permeable stretching sheet in presence of time dependent free stream velocity. Fluid is considered in the influence of transverse magnetic field in the presence of radiation effect. Rosseland approximation is use to model the radiative heat transfer. Using time-dependent stream function, partial differential equations corresponding to the momentum and energy equations are converted into non-linear ordinary differential equations. Numerical solutions of these equations are obtained by using Runge-Kutta Fehlberg method with the help of Newton-Raphson shooting technique. In the present work the effect of unsteadiness parameter, magnetic field parameter, radiation parameter, stretching parameter and the Prandtl number on flow and heat transfer characteristics have been discussed. Skin-friction coefficient and Nusselt number at the sheet are computed and discussed. The results reported in the paper are in good agreement with published work in literature by other researchers.
Abstract: In order to obtaining the dynamic evolution image of Tungsten array for foam padding, and to research the form of interaction between Tungsten plasma and foam column, a shadow imaging system of four-frame ultraviolet probe laser (266nm)has been designed on 1MA pulse power device. The time resolution of the system is 2.5ns, and static space resolution is superior to 70μm. The radial shadowgraphy image reveals the whole process from the melting and expansion of solid wire to the interaction of the precursor plasma and the foam, from the pinch to rebound inflation. The image shows the continuous interaction of Tungsten plasma and foam in a form of “Raining" within a time of about 50ns, the plasma shell structure has not been found in the whole period of pinch. The quantitative analysis indicates the minimum pinching speed of the foam column is 1.0×106cm/s, and maximum pinching speed is 6.0×106cm/s, and the axial stagnation diameter is approx 1mm.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: The nanotechnology based on epitaxial systems
includes single or arranged misfit dislocations. In general, whatever
is the type of dislocation or the geometry of the array formed by the
dislocations; it is important for experimental studies to know exactly
the stress distribution for which there is no analytical expression [1,
2]. This work, using a numerical analysis, deals with relaxation of
epitaxial layers having at their interface a periodic network of edge
misfit dislocations. The stress distribution is estimated by using
isotropic elasticity. The results show that the thickness of the two
sheets is a crucial parameter in the stress distributions and then in the
profile of the two sheets.
A comparative study between the case of single dislocation and
the case of parallel network shows that the layers relaxed better when
the interface is covered by a parallel arrangement of misfit.
Consequently, a single dislocation at the interface produces an
important stress field which can be reduced by inserting a parallel
network of dislocations with suitable periodicity.
Abstract: Over the course of the past century, the global
automotive industry-s stance towards safety has evolved from one of
contempt to one nearing reverence. A suspension system that
provides safe handling and cornering capabilities can, with the help
of an efficient braking system, improve safety to a large extent. The
aim of this research is to propose a new automotive brake rotor
design and to compare it with automotive vented disk rotor. Static
structural and transient thermal analysis have been carried out on the
vented disk rotor and proposed rotor designs to evaluate and compare
their performance. Finite element analysis was employed for both
static structural and transient thermal analysis. Structural analysis
was carried out to study the stress and deformation pattern of the
rotors under extreme loads. Time varying temperature load was
applied on the rotors and the temperature distribution was analysed
considering cooling parameters (convection and radiation). This
dissertation illustrates the use of Finite Element Methods to examine
models, concluding with a comparative study of the proposed rotor
design and the conventional vented disk rotor for structural stability
and thermal efficiency.
Abstract: This paper presents the development of an active
vibration control using direct adaptive controller to suppress the
vibration of a flexible beam system. The controller is realized based
on linear parametric form. Differential evolution optimisation
algorithm is used to optimize the controller using single objective
function by minimizing the mean square error of the observed
vibration signal. Furthermore, an alternative approach is developed to
systematically search for the best controller model structure together
with it parameter values. The performance of the control scheme is
presented and analysed in both time and frequency domain.
Simulation results demonstrate that the proposed scheme is able to
suppress the unwanted vibration effectively.
Abstract: In this paper presents the mathematical model of
hydrothermal processes in thermal power plant with different wind
direction scenarios in the water reservoir, which is solved by the
Navier - Stokes and temperature equations for an incompressible
fluid in a stratified medium. Numerical algorithm based on the
method of splitting by physical parameters. Three dimensional
Poisson equation is solved with Fourier method by combination of
tridiagonal matrix method (Thomas algorithm).
Abstract: Having done in this study, air-conditioning
automation for patisserie shopwindow was designed. In the cooling
sector it is quite important to cooling up the air temperature in the
shopwindow within short time interval. Otherwise the patisseries
inside of the shopwindow will be spoilt in a few days. Additionally
the humidity is other important parameter for the patisseries kept in
shopwindow. It must be raised up to desired level in a quite short
time. Traditional patisserie shopwindows only allow controlling
temperature manually. There is no humidity control and humidity is
supplied by fans that are directed to the water at the bottom of the
shopwindows. In this study, humidity and temperature sensors
(SHT11), PIC, AC motor controller, DC motor controller, ultrasonic
nebulizer and other electronic circuit members were used to simulate
air conditioning automation for patisserie shopwindow in proteus
software package. The simulation results showed that temperature
and humidity values are adjusted in desired time duration by openloop
control technique. Outer and inner temperature and humidity
values were used for control mechanism.
Abstract: This paper derives some new sufficient conditions for
the stability of a class of neutral-type neural networks with discrete
time delays by employing a suitable Lyapunov functional. The
obtained conditions can be easily verified as they can be expressed
in terms of the network parameters only. It is shown that the results
presented in this paper for neutral-type delayed neural networks establish
a new set of stability criteria, and therefore can be considered
as the alternative results to the previously published literature results.
A numerical example is also given to demonstrate the applicability
of our proposed stability criterion.
Abstract: Biclustering is a very useful data mining technique for
identifying patterns where different genes are co-related based on a
subset of conditions in gene expression analysis. Association rules
mining is an efficient approach to achieve biclustering as in
BIMODULE algorithm but it is sensitive to the value given to its
input parameters and the discretization procedure used in the
preprocessing step, also when noise is present, classical association
rules miners discover multiple small fragments of the true bicluster,
but miss the true bicluster itself. This paper formally presents a
generalized noise tolerant bicluster model, termed as μBicluster. An
iterative algorithm termed as BIDENS based on the proposed model
is introduced that can discover a set of k possibly overlapping
biclusters simultaneously. Our model uses a more flexible method to
partition the dimensions to preserve meaningful and significant
biclusters. The proposed algorithm allows discovering biclusters that
hard to be discovered by BIMODULE. Experimental study on yeast,
human gene expression data and several artificial datasets shows that
our algorithm offers substantial improvements over several
previously proposed biclustering algorithms.