Abstract: In this paper we describe the Levenvberg-Marquardt
(LM) algorithm for identification and equalization of CDMA
signals received by an antenna array in communication channels.
The synthesis explains the digital separation and equalization of
signals after propagation through multipath generating intersymbol
interference (ISI). Exploiting discrete data transmitted and three
diversities induced at the reception, the problem can be composed
by the Block Component Decomposition (BCD) of a tensor of
order 3 which is a new tensor decomposition generalizing the
PARAFAC decomposition. We optimize the BCD decomposition by
Levenvberg-Marquardt method gives encouraging results compared to
classical alternating least squares algorithm (ALS). In the equalization
part, we use the Minimum Mean Square Error (MMSE) to perform
the presented method. The simulation results using the LM algorithm
are important.
Abstract: Presently, engine cooling pump is driven by toothed
belt. Therefore, the pump speed is dependent on engine speed which
varies their output. At normal engine operating conditions (Higher
RPM and low load, Higher RPM and high load), mechanical water
pumps in existing engines are inevitably oversized and so the use of
an electric water pump together with state-of-the-art thermal
management of the combustion engine has measurable advantages.
Demand-driven cooling, particularly in the cold-start phase, saves
fuel (approx 3 percent) and leads to a corresponding reduction in
emissions. The lack of dependence on a mechanical drive also results
in considerable flexibility in component packaging within the engine
compartment. This paper describes the testing and comparison of
existing mechanical water pump with that of the electric water pump.
When the existing mechanical water pump is replaced with the new
electric water pump the percentage gain in system efficiency is also
discussed.
Abstract: In this study, the performance analyses of the twenty
five Coal-Fired Power Plants (CFPPs) used for electricity generation
are carried out through various Data Envelopment Analysis (DEA)
models. Three efficiency indices are defined and pursued. During the
calculation of the operational performance, energy and non-energy
variables are used as input, and net electricity produced is used as
desired output (Model-1). CO2 emitted to the environment is used as
the undesired output (Model-2) in the computation of the pure
environmental performance while in Model-3 CO2 emissions is
considered as detrimental input in the calculation of operational and
environmental performance. Empirical results show that most of the
plants are operating in increasing returns to scale region and Mettur
plant is efficient one with regards to energy use and environment.
The result also indicates that the undesirable output effect is
insignificant in the research sample. The present study will provide
clues to plant operators towards raising the operational and
environmental performance of CFPPs.
Abstract: Environmental impacts of six 3D printers using
various materials were compared to determine if material choice
drove sustainability, or if other factors such as machine type, machine
size, or machine utilization dominate. Cradle-to-grave life-cycle
assessments were performed, comparing a commercial-scale FDM
machine printing in ABS plastic, a desktop FDM machine printing in
ABS, a desktop FDM machine printing in PET and PLA plastics, a
polyjet machine printing in its proprietary polymer, an SLA machine
printing in its polymer, and an inkjet machine hacked to print in salt
and dextrose. All scenarios were scored using ReCiPe Endpoint H
methodology to combine multiple impact categories, comparing
environmental impacts per part made for several scenarios per
machine. Results showed that most printers’ ecological impacts were
dominated by electricity use, not materials, and the changes in
electricity use due to different plastics was not significant compared
to variation from one machine to another. Variation in machine idle
time determined impacts per part most strongly. However, material
impacts were quite important for the inkjet printer hacked to print in
salt: In its optimal scenario, it had up to 1/38th the impacts coreper
part as the worst-performing machine in the same scenario. If salt
parts were infused with epoxy to make them more physically robust,
then much of this advantage disappeared, and material impacts
actually dominated or equaled electricity use. Future studies should
also measure DMLS and SLS processes / materials.
Abstract: One of the major difficulties introduced with wind
power penetration is the inherent uncertainty in production originating
from uncertain wind conditions. This uncertainty impacts many
different aspects of power system operation, especially the balancing
power requirements. For this reason, in power system development
planing, it is necessary to evaluate the potential uncertainty in future
wind power generation. For this purpose, simulation models are
required, reproducing the performance of wind power forecasts.
This paper presents a wind power forecast error simulation models
which are based on the stochastic process simulation. Proposed
models capture the most important statistical parameters recognized
in wind power forecast error time series. Furthermore, two distinct
models are presented based on data availability. First model uses
wind speed measurements on potential or existing wind power plant
locations, while the seconds model uses statistical distribution of wind
speeds.
Abstract: Measurements and quantitative analysis of kinematic
parameters of human hand movements have an important role in
different areas such as hand function rehabilitation, modeling of
multi-digits robotic hands, and the development of machine-man
interfaces. In this paper the assessment and evaluation of the reachto-
grasp movement by using computerized and robot-assisted method
is described. Experiment involved the measurements of hand
positions of seven healthy subjects during grasping three objects of
different shapes and sizes. Results showed that three dominant phases
of reach-to-grasp movements could be clearly identified.
Abstract: It is difficult to study the effect of various variables on
cycle fitting through actual experiment. To overcome such difficulty,
the forward dynamics of a musculoskeletal model was applied to cycle
fitting in this study. The measured EMG data weres compared with the
muscle activities of the musculoskeletal model through forward
dynamics. EMG data were measured from five cyclists who do not
have musculoskeletal diseases during three minutes pedaling with a
constant load (150 W) and cadence (90 RPM). The muscles used for
the analysis were the Vastus Lateralis (VL), Tibialis Anterior (TA),
Bicep Femoris (BF), and Gastrocnemius Medial (GM). Person’s
correlation coefficients of the muscle activity patterns, the peak timing
of the maximum muscle activities, and the total muscle activities were
calculated and compared. BIKE3D model of AnyBody (Anybodytech,
Denmark) was used for the musculoskeletal model simulation. The
comparisons of the actual experiments with the simulation results
showed significant correlations in the muscle activity patterns (VL:
0.789, TA: 0.503, BF: 0.468, GM: 0.670). The peak timings of the
maximum muscle activities were distributed at particular phases. The
total muscle activities were compared with the normalized muscle
activities, and the comparison showed about 10% difference in the VL
(+10%), TA (+9.7%), and BF (+10%), excluding the GM (+29.4%).
Thus, it can be concluded that muscle activities of model &
experiment showed similar results. The results of this study indicated
that it was possible to apply the simulation of further improved
musculoskeletal model to cycle fitting.
Abstract: In this paper, extract of papaya leaves are used as a
natural dye and combined by variations of solvent concentration
applied on DSSC (Dye-Sensitized Solar Cell). Indonesian geographic
located on the equator line occasions the magnitude of the potential
to develop organic solar cells made from extracts of chlorophyll as a
substitute for inorganic materials or synthetic dye on DSSC material.
Dye serves as absorbing photons which are then converted into
electrical energy. A conductive coated glass layer called TCO
(Transparent Conductive Oxide) is used as a substrate of electrode.
TiO2 nanoparticles as binding dye molecules, redox couple iodide/
tri-iodide as the electrolyte and carbon as the counter electrode in the
DSSC are used. TiO2 nanoparticles, organic dyes, electrolytes, and
counter electrode are arranged and combined with the layered
structure of the photo-catalyst absorption layer. Dye absorption
measurements using a spectrophotometer at 400-800 nm light
spectrum produces a total amount of chlorophyll 80.076 mg/l. The
test cell at 7 watt LED light with 5000 lux luminescence was
obtained Voc and Isc of 235.5 mV and 14 μA, respectively.
Abstract: This paper describes a novel application of Fiber
Braggs Grating (FBG) sensors in the assessment of human postural
stability and balance on an unstable platform. In this work, FBG
sensor Stability Analyzing Device (FBGSAD) is developed for
measurement of plantar strain to assess the postural stability of
subjects on unstable platforms during different stances in eyes open
and eyes closed conditions on a rocker board. The studies are
validated by comparing the Centre of Gravity (CG) variations
measured on the lumbar vertebra of subjects using a commercial
accelerometer. The results obtained from the developed FBGSAD
depict qualitative similarities with the data recorded by commercial
accelerometer. The advantage of the FBGSAD is that it measures
simultaneously plantar strain distribution and postural stability of the
subject along with its inherent benefits like non-requirement of
energizing voltage to the sensor, electromagnetic immunity and
simple design which suits its applicability in biomechanical
applications. The developed FBGSAD can serve as a tool/yardstick to
mitigate space motion sickness, identify individuals who are
susceptible to falls and to qualify subjects for balance and stability,
which are important factors in the selection of certain unique
professionals such as aircraft pilots, astronauts, cosmonauts etc.
Abstract: In this article, we have elaborated a study over the
nature of financial intermediation in Islamic banks by comparison to
those of conventional ones. We have found a striking difference
between two kinds of intermediation. We tried, from another side, to
study the relationship between the capital level and deficiency risk
relying on econometric model, and we have obtained a positive and
significant relation between the capital and the deficiency risk for the
conventional banks. This means that when the capital of these banks
increases, the deficiency risk increases as well. In return, since the
Islamic banks are constrained to respect the Sharia Committee as well
as customers’ demands that may, in certain contracts, choose to
invest their capitals in projects they are interested in. These
constraints have as effects to reduce the deficiency risk even when
the capital increases.
Abstract: Nowadays, the successful implementation of ICTs is
vital for almost any kind of organization. Good governance and ICT
management are essential for delivering value, managing
technological risks, managing resources and performance
measurement. In addition, outsourcing is a strategic IT service
solution which complements IT services provided internally in
organizations. This paper proposes the measurement tools of a new
holistic maturity model based on standards ISO/IEC 20000 and
ISO/IEC 38500, and the frameworks and best practices of ITIL and
COBIT, with a specific focus on IT outsourcing. These measurement
tools allow independent validation and practical application in the
field of higher education, using a questionnaire, metrics tables, and
continuous improvement plan tables as part of the measurement
process. Guidelines and standards are proposed in the model for
facilitating adaptation to universities and achieving excellence in the
outsourcing of IT services.
Abstract: Starting in 2020, an EU-wide CO2-limitation of
95 g/km is scheduled for the average of an OEMs passenger car fleet.
Taking that into consideration additional improvement measures of
the Diesel cycle are necessary in order to reduce fuel consumption
and emissions while boosting, or at the least, keeping performance
values at the same time.
The present article deals with the possibilities of an optimized
air/water charge air cooler, also called iCAC (indirect Charge Air
Cooler) for a Diesel passenger car amongst extreme-boundary
conditions. In this context, the precise objective was to show the
impact of improved intercooling with reference to the engine working
process (fuel consumption and NOx-emissions). Several extremeboundaries
- e.g. varying ambient temperatures or mountainous
routes - that will become very important in the near future regarding
RDE (Real Driving emissions) were subject of the investigation.
With the introduction of RDE in 2017 (EU6c measure), the
controversial NEDC (New European Driving Cycle) will belong to
the past and the OEMs will have to avoid harmful emissions in any
conceivable real life situation.
This is certainly going to lead to optimization-measurements at the
powertrain, which again is going to make the implementation of
iCACs, presently solely used for the premium class, more and more
attractive for compact class cars. The investigations showed a benefit
in FC between 1 and 3% for the iCAC in real world conditions.
Abstract: Water spray cooling is a technique typically used in
heat treatment and other metallurgical processes where controlled
temperature regimes are required. Water spray cooling is used in
static (without movement) or dynamic (with movement of the steel
plate) regimes. The static regime is notable for the fixed position of
the hot steel plate and fixed spray nozzle. This regime is typical for
quenching systems focused on heat treatment of the steel plate. The
second application of spray cooling is the dynamic regime. The
dynamic regime is notable for its static section cooling system and
moving steel plate. This regime is used in rolling and finishing mills.
The fixed position of cooling sections with nozzles and the
movement of the steel plate produce nonhomogeneous water
distribution on the steel plate. The length of cooling sections and
placement of water nozzles in combination with the nonhomogeneity
of water distribution lead to discontinued or interrupted cooling
conditions. The impact of static and dynamic regimes on cooling
intensity and the heat transfer coefficient during the cooling process
of steel plates is an important issue.
Heat treatment of steel is accompanied by oxide scale growth. The
oxide scale layers can significantly modify the cooling properties and
intensity during the cooling. The combination of static and dynamic
(section) regimes with the variable thickness of the oxide scale layer
on the steel surface impact the final cooling intensity. The study of
the influence of the oxide scale layers with different cooling regimes
was carried out using experimental measurements and numerical
analysis. The experimental measurements compared both types of
cooling regimes and the cooling of scale-free surfaces and oxidized
surfaces. A numerical analysis was prepared to simulate the cooling
process with different conditions of the section and samples with
different oxide scale layers.
Abstract: In this study, attempt has been made to investigate the
relationship specifically the causal relation between fund unit prices
of Islamic equity unit trust fund which measure by fund NAV and the
selected macro-economic variables of Malaysian economy by using
VECM causality test and Granger causality test. Monthly data has
been used from Jan, 2006 to Dec, 2012 for all the variables. The
findings of the study showed that industrial production index,
political election and financial crisis are the only variables having
unidirectional causal relationship with fund unit price. However the
global oil price is having bidirectional causality with fund NAV.
Thus, it is concluded that the equity unit trust fund industry in
Malaysia is an inefficient market with respect to the industrial
production index, global oil prices, political election and financial
crisis. However the market is approaching towards informational
efficiency at least with respect to four macroeconomic variables,
treasury bill rate, money supply, foreign exchange rate, and
corruption index.
Abstract: Developing young people’s employability is a key
policy issue for ensuring their successful transition to the labour
market and their access to career oriented employment. The youths of
today irrespective of their gender need to acquire the knowledge,
skills and attitudes that will enable them to create or find jobs as well
as cope with unpredictable labour market changes throughout their
working lives. In a study carried out to determine the influence of
gender on job-competencies requirements of chemical-based
industries and undergraduate-competencies acquisition by chemists
working in the industries, all chemistry graduates working in twenty
(20) chemical-based industries that were randomly selected from six
sectors of chemical-based industries in Lagos and Ogun States of
Nigeria were administered with Job-competencies required and
undergraduate-competencies acquired assessment questionnaire. The
data were analysed using means and independent sample t-test. The
findings revealed that the population of female chemists working in
chemical-based industries is low compared with the number of male
chemists; furthermore, job-competencies requirements are found not
to be gender biased while there is no significant difference in
undergraduate-competencies acquisition of male and female
chemists. This suggests that females should be given the same
opportunity of employment in chemical-based industries as their male
counterparts. The study also revealed the level of acquisition of
undergraduate competencies as related to the needs of chemicalbased
industries.
Abstract: In this paper, effect of marginal quality groundwater
on yield of cotton crop and soil salinity was studied. In this
connection, three irrigation treatments each with four replications
were applied. These treatments were i) use of canal water (T1), ii) use
of marginal quality groundwater from tubewell (T2), and iii)
conjunctive use by mixing with the ratio of 1:1 of canal water and
marginal quality tubewell water (T3).
Water was applied to the crop cultivated in Kharif season 2011; its
quantity has been measured using cut-throat flume. Total 11 watering
each of 50 mm depth have been applied from 20th April to 20th July,
2011. Further, irrigations were stopped due to monsoon rainfall up to
crop harvesting.
Maximum crop yield (seed cotton) was observed under T1 which
was 1,517 kg/ha followed by T3 (mixed canal and tubewell water)
having 1009 kg/ha and T2 i.e. marginal quality groundwater having
709 kg/ha. This concludes that crop yield in T2 and T3 in comparison
to T1was reduced by about 53 and 30% respectively.
It has been observed that yield of cotton crop is below potential
limit for three treatments due to unexpected rainfall at the time of full
flowering season; thus the yield was adversely affected.
However, salt deposition in soil profiles was not observed that is
due to leaching effect of heavy rainfall occurred during monsoon
season.
Abstract: In this study which has been conducted in Akçasu
Forest Range District of Devrek Forest Directorate; 3 methods (weed
control with labourer power, cover removal with Hitachi F20
Excavator, and weed control with agricultural equipment mounted on
a Ferguson 240S agriculture tractor) were utilized in weed control
efforts in regeneration of degraded oriental beech forests have been
compared. In this respect, 3 methods have been compared by
determining certain work hours and standard durations of unit areas
(1 hectare). For this purpose, evaluating the tasks made with human
and machine force from the aspects of duration, productivity and
costs, it has been aimed to determine the most productive method in
accordance with the actual ecological conditions of research field.
Within the scope of the study, the time studies have been conducted
for 3 methods used in weed control efforts. While carrying out those
studies, the performed implementations have been evaluated by
dividing them into business stages. Also, the actual data have been
used while calculating the cost accounts. In those calculations, the
latest formulas and equations which are also used in developed
countries have been utilized. The variance of analysis (ANOVA) was
used in order to determine whether there is any statistically
significant difference among obtained results, and the Duncan test
was used for grouping if there is significant difference. According to
the measurements and findings carried out within the scope of this
study, it has been found during living cover removal efforts in
regeneration efforts in demolished oriental beech forests that the
removal of weed layer in 1 hectare of field has taken 920 hours with
labourer force, 15.1 hours with excavator and 60 hours with an
equipment mounted on a tractor. On the other hand, it has been
determined that the cost of removal of living cover in unit area (1
hectare) was 3220.00 TL for labourer power, 1250 TL for excavator
and 1825 TL for equipment mounted on a tractor.
According to the obtained results, it has been found that the
utilization of excavator in weed control effort in regeneration of
degraded oriental beech regions under actual ecological conditions of
research field has been found to be more productive from both of
aspects of duration and costs. These determinations carried out
should be repeated in weed control efforts in degraded forest fields
with different ecological conditions, it is compulsory for finding the
most efficient weed control method. These findings will light the way
of technical staff of forestry directorate in determination of the most
effective and economic weed control method. Thus, the more actual
data will be used while preparing the weed control budgets, and there
will be significant contributions to national economy. Also the results of this and similar studies are very important for developing the policies for our forestry in short and long term.
Abstract: Nowadays social media information, such as news,
links, images, or VDOs, is shared extensively. However, the
effectiveness of disseminating information through social media
lacks in quality: less fact checking, more biases, and several rumors.
Many researchers have investigated about credibility on Twitter, but
there is no the research report about credibility information on
Facebook. This paper proposes features for measuring credibility on
Facebook information. We developed the system for credibility on
Facebook. First, we have developed FB credibility evaluator for
measuring credibility of each post by manual human’s labelling. We
then collected the training data for creating a model using Support
Vector Machine (SVM). Secondly, we developed a chrome extension
of FB credibility for Facebook users to evaluate the credibility of
each post. Based on the usage analysis of our FB credibility chrome
extension, about 81% of users’ responses agree with suggested
credibility automatically computed by the proposed system.
Abstract: With a long history, dual-task has become one of the
most intriguing research fields regarding human brain functioning
and cognition. However, findings considering effects of taskinterrelations
are limited (especially, in combined motor and
cognitive tasks). Therefore, we aimed at developing a measurement
system in order to analyse interrelation effects of cognitive and motor
tasks. On the one hand, the present study demonstrates the
applicability of the measurement system and on the other hand first
results regarding a systematisation of different task combinations are
shown. Future investigations should combine imagine technologies
and this developed measurement system.
Abstract: Geopolymer concretes are new class of construction
materials that have emerged as an alternative to Ordinary Portland
cement concrete. Considerable researches have been carried out on
material development of geopolymer concrete; however, a few studies
have been reported on the structural use of them. This paper presents
the bond behaviors of reinforcement embedded in fly ash based
geopolymer concrete. The development lengths of reinforcement for
various compressive strengths of concrete, 20, 30 and 40 MPa, and
reinforcement diameters, 10, 16 and 25 mm, are investigated. Total 27
specimens were manufactured and pull-out test according to EN 10080
was applied to measure bond strength and slips between concrete and
reinforcements. The average bond strengths decreased from 23.06MPa
to 17.26 MPa, as the diameters of reinforcements increased from
10mm to 25mm. The compressive strength levels of geopolymer
concrete showed no significant influence on bond strengths in this
study. Also, the bond-slip relations between geopolymer concrete and
reinforcement are derived using non-linear regression analysis for
various experimental conditions.