Abstract: Experiments have been performed to investigate the radiation effects on mixed convection heat transfer for thermally developing airflow in vertical ducts with two differentially heated isothermal walls and two adiabatic walls. The investigation covers the Reynolds number Re = 800 to Re = 2900, heat flux varied from 256 W/m2 to 863 W/m2, hot wall temperature ranges from 27°C to 100 °C, aspect ratios 1 & 0.5 and the emissivity of internal walls are 0.05 and 0.85. In the present study, combined flow visualization was conducted to observe the flow patterns. The effect of surface temperature along the walls was studied to investigate the local Nusselt number variation within the duct. The result shows that flow condition and radiation significantly affect the total Nusselt number and tends to reduce the buoyancy condition.
Abstract: Mercury is a natural occurring element and present in
various concentrations in the environment. Due to its toxic effects, it
is desirable to research mercury sensitive materials to adsorb
mercury. This paper describes the preparation of Au nanoparticles for
mercury adsorption by using a microwave (MW)-polyol method in
the presence of three different Sodium Chloride (NaCl)
concentrations (10, 20 and 30 mM). Mixtures of spherical, triangular,
octahedral, decahedral particles and 1-D product were obtained using
this rapid method. Sizes and shapes was found strongly depend on the
concentrations of NaCl. Without NaCl concentration, spherical,
triangular plates, octahedral, decahedral nanoparticles and 1D
product were produced. At the lower NaCl concentration (10 mM),
spherical, octahedral and decahedral nanoparticles were present,
while spherical and decahedral nanoparticles were preferentially form
by using 20 mM of NaCl concentration. Spherical, triangular plates,
octahedral and decahedral nanoparticles were obtained at the highest
NaCl concentration (30 mM). The amount of mercury adsorbed using
20 ppm mercury solution is the highest (67.5 %) for NaCl
concentration of 30 mM. The high yield of polygonal particles will
increase the mercury adsorption. In addition, the adsorption of
mercury is also due to the sizes of the particles. The sizes of particles
become smaller with increasing NaCl concentrations (size ranges, 5-
16 nm) than those synthesized without addition of NaCl (size ranges
11-32 nm). It is concluded that NaCl concentrations affects the
formation of sizes and shapes of Au nanoparticles thus affects the
mercury adsorption.
Abstract: Passive systems were born with the purpose of the
greatest exploitation of solar energy in cold climates and high
altitudes. They spread themselves until the 80-s all over the world
without any attention to the specific climate and the summer
behavior; this caused the deactivation of the systems due to a series
of problems connected to the summer overheating, the complex
management and the rising of the dust.
Until today the European regulation limits only the winter
consumptions without any attention to the summer behavior but, the
recent European EN 15251 underlines the relevance of the indoor
comfort, and the necessity of the analytic studies validation by
monitoring case studies.
In the porpose paper we demonstrate that the solar wall is an
efficient system both from thermal comfort and energy saving point
of view and it is the most suitable for our temperate climates because
it can be used as a passive cooling sistem too. In particular the paper
present an experimental and numerical analisys carried out on a case
study with nine different solar passive systems in Ancona, Italy.
We carried out a detailed study of the lodging provided by the
solar wall by the monitoring and the evaluation of the indoor
conditions.
Analyzing the monitored data, on the base of recognized models
of comfort (ISO, ASHRAE, Givoni-s BBCC), is emerged that the
solar wall has an optimal behavior in the middle seasons. In winter
phase this passive system gives more advantages in terms of energy
consumptions than the other systems, because it gives greater heat
gain and therefore smaller consumptions. In summer, when outside
air temperature return in the mean seasonal value, the indoor comfort
is optimal thanks to an efficient transversal ventilation activated from
the same wall.
Abstract: Shrunken patterning for integrated device
manufacturing requires surface cleanliness and surface smoothness in
wet chemical processing [1]. It is necessary to control all process
parameters perfectly especially for the common cleaning technique
RCA clean (SC-1 and SC-2) [2]. In this paper the characteristic and
effect of surface preparation parameters are discussed. The properties
of RCA wet chemical processing in silicon technology is based on
processing time, temperature, concentration and megasonic power of
SC-1 and QDR. An improvement of wafer surface preparation by
the enhanced variables of the wet cleaning chemical process is
proposed.
Abstract: In this paper, a novel system
recognition of human faces without using face
different color photographs is proposed. It mainly in
face detection, normalization and recognition. Foot
method of combination of Haar-like face determined
segmentation and region-based histogram stretchi
(RHST) is proposed to achieve more accurate perf
using Haar. Apart from an effective angle norm
side-face (pose) normalization, which is almost a might be important and beneficial for the prepr
introduced. Then histogram-based and photom
normalization methods are investigated and ada
retinex (ASR) is selected for its satisfactory illumin
Finally, weighted multi-block local binary pattern
with 3 distance measures is applied for pair-mat
Experimental results show its advantageous perfo
with PCA and multi-block LBP, based on a principle.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: The objective of the present study was to examine the
dose-response relationships between antioxidant parameters and liver
contaminant levels of Kazakhstan light crude oil (KLCO) in albino
rats. The animals were repeatedly exposed, by intraperitoneal
injection, to low dosages (0.5–1.5 ml/kg) of KLCO. Rats exposed to
these doses levels did not show any apparent symptoms of
intoxication. Serum aminotransferases increased significantly
(p
Abstract: Full - Scale Accelerated Loading System, one part of
“the Eleventh - Five - Year National Grand Technology Infrastructure
Program" is a facility to evaluate the performance and service life of
different kinds of pavements subjected to traffic loading under full -
controlled environment. While simulating the environments of frigid
zone and permafrost zone, the accurate control of air temperature, road
temperature and roadbed temperature are the key points and also
aporias for the designment. In this paper, numerical simulations are
used to determine the design parameters of the frozen soil simulation
system. At first, a brief introduction of the Full - Scale Accelerate
Loading System was given. Then, the temperature control method of
frozen soil simulation system was proposed. Finally, by using finite
element simulations, the optimal design of frozen soil simulation
system was obtained. This proposed design, which was obtained by
finite element simulations, provided significant referents to the
ultimate design of the environment simulation system.
Abstract: The Build-Then-Sell (BTS) is a novel system
implemented in Malaysia after a number of complaints have been
received from buyers in the preceding Sell-Then-Build (STB) system.
When the government announced the implementation of the BTS in
2007, proponents of BTS have asserted that the new system will
provide houses with low level of defects. Their argument however is
not supported by any empirical data. Hence, this study is conducted
to evaluate the housing defects in BTS houses. Six BTS residential
areas have been surveyed to collect the defects data. Questionnaires
were administered directly to the occupiers in each of the BTS houses
through door-to-door visits. The result has shown that the rate of
defects for the six residential areas is ranged from minor to slight,
which only affect the aesthetic value of the house.
Abstract: In determining the electromagnetic properties of
magnetic materials, hysteresis modeling is of high importance. Many
models are available to investigate those characteristics but they tend
to be complex and difficult to implement. In this paper a new
qualitative hysteresis model for ferromagnetic core is presented,
based on the function approximation capabilities of adaptive neuro
fuzzy inference system (ANFIS). The proposed ANFIS model
combined the neural network adaptive capabilities and the fuzzy
logic qualitative approach can restored the hysteresis curve with a
little RMS error. The model accuracy is good and can be easily
adapted to the requirements of the application by extending or
reducing the network training set and thus the required amount of
measurement data.
Abstract: the purpose of this research is to identify and clarify
factors which have positive effect among user satisfaction and their
social networking through websites. The examined factors in this
research are; innovation, ease of use, trustworthy and customer
support which are defined as satisfaction factors. To obtain reliable
research approaches and to have better result in this research four
hypothesizes used to test. This hypothesis testing has been done by
correlation, regression and test of normality by using “SPSS16" also
the data which was analyzed by this software. this data was gathered
from prepaid questionnaire.
Abstract: From environmental aspect purification of ammonia
containing wastewater is expected. High efficiency ammonia
desorption can be done from the water by air on proper temperature.
After the desorption process, ammonia can be recovered and used in
another technology. The calculation method described below give
some methods to find either the minimum column height or ammonia
rich solution of the effluent.
Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: In order to survive in a rapidly changing business environment, Malaysian business firms must improve their own business practices and procedures. This paper describes the impact of Critical Success Factors (CSFs) during the Enterprise Resource Planning (ERP) system implementations using the responses from 151 organizations that completed or are in the process of completing an ERP implementation and identifying the key benefits of ERP implementation in the firm. The importance of these factors was investigated within Malaysian companies using questionnaire survey method. Our results provide advice to management on how best to utilize their limited resources to choose those CSFs that are most likely to have an impact upon the implementation of the ERP system.
Abstract: A model of (4, 4) single-walled boron-nitride nanotube as a representative of armchair boron-nitride nanotubes studied. At first the structure optimization performed and then Nuclear Magnetic Resonance parameters (NMR) by Density Functional Theory (DFT) method at 11B and 15N nuclei calculated. Resulted parameters evaluation presents electrostatic environment heterogeneity along the nanotube and especially at the ends but the nuclei in a layer feel the same electrostatic environment. All of calculations carried out using Gaussian 98 Software package.
Abstract: Conventional industrial monitoring systems are
tedious, inefficient and the at times integrity of the data is
unreliable. The objective of this system is to monitor industrial
processes specifically the fluid level which will measure the
instantaneous fluid level parameter and respond by text
messaging the exact value of the parameter to the user when
being enquired by a privileged access user. The development of
the embedded program code and the circuit for fluid level
measuring are discussed as well. Suggestions for future
implementations and efficient remote monitoring works are
included.
Abstract: Our results showed that treatment with both
cyclooxygenase (COX1 or COX2) inhibitors impair reproduction
parameters of the medaka. Resveratrol (COX1 inhibitor) caused an
decrease in the number of spawning females at the first week of
feeding fish with experimental diets. In the group treated with NS-
398 (COX2 inhibitor) we found the lowest sperm velocity parameters
and decreased linearity of movement. The ovaries of the medaka fed
feed supplemented with Resveratrol or NS-398 were confirmed to
have a lower share of matured oocytes however during the
experiment (four weeks) the number of eggs spawned by females was
similar. Both inhibitors in fish diet (20 mg/kg body weight/day)
caused a decrease in the embryo survival. Our results revealed that
for the medaka female reproduction, activity of both COX enzymes
might be necessary whereas males reproduction competence, as
expressed by sperm motility parameters, might be related to COX2
activity.
Abstract: One of the most important parts of a cement factory is
the cement rotary kiln which plays a key role in quality and quantity of produced cement. In this part, the physical exertion and bilateral
movement of air and materials, together with chemical reactions take
place. Thus, this system has immensely complex and nonlinear dynamic equations. These equations have not worked out yet. Only
in exceptional case; however, a large number of the involved parameter were crossed out and an approximation model was
presented instead. This issue caused many problems for designing a
cement rotary kiln controller. In this paper, we presented nonlinear predictor and simulator models for a real cement rotary kiln by using
nonlinear identification technique on the Locally Linear Neuro-
Fuzzy (LLNF) model. For the first time, a simulator model as well as
a predictor one with a precise fifteen minute prediction horizon for a
cement rotary kiln is presented. These models are trained by
LOLIMOT algorithm which is an incremental tree-structure
algorithm. At the end, the characteristics of these models are expressed. Furthermore, we presented the pros and cons of these
models. The data collected from White Saveh Cement Company is used for modeling.
Abstract: Recently, the health of retired National Football
League players, particularly lineman has been investigated. A number of studies have reported increased cardiometabolic risk, premature ardiovascular disease and incidence of type 2 diabetes. Rugby union players have somatotypes very similar
to National Football league players which suggest that rugby players may have similar health risks. The International Golden Oldies World Rugby Festival (GORF) provided a
unique opportunity to investigate the demographics of veteran rugby players. METHODOLOGIES: A cross-sectional, observational study was completed using an online web-based
questionnaire that consisted of medical history and
physiological measures. Data analysis was completed using a one sample t-test (50yrs) and Chi-square test. RESULTS: A total of 216 veteran rugby competitors
(response rate = 6.8%) representing 10 countries, aged 35-72 yrs (mean 51.2, S.D. ±8.0), participated in the online survey. As a group, the incidence of current smokers was low at 8.8%
(avg 72.4 cigs/wk) whilst the percentage consuming alcohol
was high (93.1% (avg 11.2 drinks/wk). Competitors reported
the following top six chronic diseases/disorders; hypertension
(18.6%), arthritis (OA/RA, 11.5%), asthma (9.3%),
hyperlipidemia (8.2%), diabetes (all types, 7.5%) and gout (6%), there were significant differences between groups with
regard to cancer (all types) and migraines. When compared to
the Australian general population (Australian Bureau of Statistics data, n=18,000), GORF competitors had a
Climstein Mike, Walsh Joe (corresponding author) and Burke Stephen
School of Exercise Science, Australian Catholic University, 25A Barker Road,
Strathfield, Sydney, NSW, 2016, Australia (e-mail:
[email protected], [email protected],
[email protected]).
John Best is with Orthosports, 160 Belmore Rd., Randwick, Sydney,NSW
2031, Australia (e-mail: [email protected]).
Heazlewood, Ian Timothy is with School of Environmental and Life
Sciences, Faculty Education, Health and Science, Charles Darwin University,
Precinct Yellow Building 2, Charles Darwin University, NT 0909, Australia
(e-mail: [email protected]).
Kettunen Jyrki Arcada University of Applied Sciences, Jan-Magnus
Janssonin aukio 1, FI-00550, Helsinki, Finland (e-mail:
[email protected]).
Adams Kent is with California State University Monterey Bay, Kinesiology Department, 100 Campus Center, Seaside, CA., 93955, USA (email: [email protected]).
DeBeliso Mark is with Department of Physical Education and Human
Performance, Southern Utah University, 351 West University Blvd, Cedar
City, Utah, USA (e-mail: [email protected]).
significantly lower incidence of anxiety (p
Abstract: This paper is an extension of a previous work where a diagonally implicit harmonic balance method was developed and applied to simulate oscillatory motions of pitching airfoil and wing. A more detailed study on the accuracy, convergence, and the efficiency of the method is carried out in the current paperby varying the number of harmonics in the solution approximation. As the main advantage of the method is itsusage for the design optimization of the unsteady problems, its application to more practical case of rotor flow analysis during forward flight is carried out and compared with flight test data and time-accurate computation results.