Abstract: In this study, a mathematical model was proposed and
the accuracy of this model was assessed to predict the growth of
Pseudomonas aeruginosa and rhamnolipid production under nitrogen
limiting (sodium nitrate) fed-batch fermentation. All of the
parameters used in this model were achieved individually without
using any data from the literature.
The overall growth kinetic of the strain was evaluated using a
dual-parallel substrate Monod equation which was described by
several batch experimental data. Fed-batch data under different
glycerol (as the sole carbon source, C/N=10) concentrations and feed
flow rates were used to describe the proposed fed-batch model and
other parameters. In order to verify the accuracy of the proposed
model several verification experiments were performed in a vast
range of initial glycerol concentrations. While the results showed an
acceptable prediction for rhamnolipid production (less than 10%
error), in case of biomass prediction the errors were less than 23%. It
was also found that the rhamnolipid production by P. aeruginosa was
more sensitive at low glycerol concentrations.
Based on the findings of this work, it was concluded that the
proposed model could effectively be employed for rhamnolipid
production by this strain under fed-batch fermentation on up to 80 g l-
1 glycerol.
Abstract: Thermally insulating ceramic coatings also known as
thermal barrier coatings (TBCs) have been essential technologies to
improve the performance and efficiency of advanced gas turbines in
service at extremely high temperatures. The damage mechanisms of
air-plasma sprayed YSZ thermal barrier coatings (TBC) with various
microstructures were studied by microscopic techniques after thermal
cycling. The typical degradation of plasma TBCs that occurs during
cyclic furnace testing of an YSZ and alumina coating on a Titanium
alloy are analyzed. During the present investigation the effects of
topcoat thickness, bond coat oxidation, thermal cycle lengths and test
temperature are investigated using thermal cycling. These results
were correlated with stresses measured by a spectroscopic technique
in order to understand specific damage mechanism. The failure
mechanism of former bond coats was found to involve fracture
initiation at the thermally grown oxide (TGO) interface and at the
TGO bond coat interface. The failure mechanism of the YZ was
found to involve combination of fracture along the interface between
TGO and bond coat.
Abstract: Buildings are one of the valuable assets to provide
people with shelters for work, leisure and rest. After years of
attacks by weather, buildings will deteriorate which need proper
maintenance in order to fulfill the requirements and satisfaction of
the users. Poorly managed buildings not just give a negative image
to the city itself, but also pose potential risk hazards to the health
and safety of the general public. As a result, the management of
maintenance projects has played an important role in cities like
Hong Kong where the problem of urban decay has drawn much
attention. However, most research has focused on managing new
construction, and little research effort has been put on maintenance
projects. Given the short duration and more diversified nature of
work, repair and maintenance works are found to be more difficult
to monitor and regulate when compared with new works. Project
participants may face with problems in running maintenance
projects which should be investigated so that proper strategies can
be established. This paper aims to provide a thorough analysis on
the problems of running maintenance projects. A review of
literature on the characteristics of building maintenance projects
was firstly conducted, which forms a solid basis for the empirical
study. Results on the problems and difficulties of running
maintenance projects from the viewpoints of industry practitioners
will also be delivered with a view to formulating effective
strategies for managing maintenance projects successfully.
Abstract: The gas safety management system using an
intelligent gas meter we proposed is to monitor flow and
pressure of gas, earthquake, temperature, smoke and leak of
methane. Then our system takes safety measures to protect a
serious risk by the result of an event, to communicate with a
wall-pad including a gateway by zigbee network in buildings
and to report the event to user by the safety management
program in a server. Also, the inner cutoff valve of an
intelligent gas meter is operated if any event occurred or
abnormal at each sensor.
Abstract: Polymerase chain reaction (PCR) assay and
conventional microbiological methods were used to detect bacterial
contamination of egg shells and egg content in different commercial
housing systems, open house system and evaporative cooling system.
A PCR assay was developed for direct detection using a set of
primers specific for the invasion by A gene (invA) of Salmonella spp.
PCR detected the presence of Salmonella in 2 samples of shell egg
from the evaporative cooling system, while conventional cultural
methods detected no Salmonella from the same samples.
Abstract: Each year many people are reported missing in most of the countries in the world owing to various reasons. Arrangements have to be made to find these people after some time. So the investigating agencies are compelled to make out these people by using manpower. But in many cases, the investigations carried out to find out an absconding for a long time may not be successful. At a time like that it may be difficult to identify these people by examining their old photographs, because their facial appearance might have changed mainly due to the natural aging process. On some occasions in forensic medicine if a dead body is found, investigations should be held to make sure that this corpse belongs to the same person disappeared some time ago. With the passage of time the face of the person might have changed and there should be a mechanism to reveal the person-s identity. In order to make this process easy, we must guess and decide as to how he will look like by now. To address this problem this paper presents a way of synthesizing a facial image with the aging effects.
Abstract: Selective oxidation of H2S to elemental sulfur in a
fixed bed reactor over newly synthesized alumina nanocatalysts was
physio-chemically investigated and results compared with a
commercial Claus catalyst. Amongst these new materials, Al2O3-
supported sodium oxide prepared with wet chemical technique and
Al2O3 nanocatalyst prepared with spray pyrolysis method were the
most active catalysts for selective oxidation of H2S to elemental
sulfur. Other prepared nanocatalysts were quickly deactivated,
mainly due to the interaction with H2S and conversion into sulfides.
Abstract: Conventional concentrically-braced frame (CBF)
systems have limited drift capacity before brace buckling and related
damage leads to deterioration in strength and stiffness. Self-centering
concentrically-braced frame (SC-CBF) systems have been developed
to increase drift capacity prior to initiation of damage and minimize
residual drift. SC-CBFs differ from conventional CBFs in that the
SC-CBF columns are designed to uplift from the foundation at a
specified level of lateral loading, initiating a rigid-body rotation
(rocking) of the frame. Vertically-aligned post-tensioning bars resist
uplift and provide a restoring force to return the SC-CBF columns to
the foundation (self-centering the system). This paper presents a
parametric study of different prototype buildings using SC-CBFs.
The bay widths of the SC-CBFs have been varied in these buildings
to study different geometries. Nonlinear numerical analyses of the
different SC-CBFs are presented to illustrate the effect of frame
geometry on the behavior and dynamic response of the SC-CBF
system.
Abstract: The visualization of geographic information on mobile devices has become popular as the widespread use of mobile Internet. The mobility of these devices brings about much convenience to people-s life. By the add-on location-based services of the devices, people can have an access to timely information relevant to their tasks. However, visual analysis of geographic data on mobile devices presents several challenges due to the small display and restricted computing resources. These limitations on the screen size and resources may impair the usability aspects of the visualization applications. In this paper, a variable-scale visualization method is proposed to handle the challenge of small mobile display. By merging multiple scales of information into a single image, the viewer is able to focus on the interesting region, while having a good grasp of the surrounding context. This is essentially visualizing the map through a fisheye lens. However, the fisheye lens induces undesirable geometric distortion in the peripheral, which renders the information meaningless. The proposed solution is to apply map generalization that removes excessive information around the peripheral and an automatic smoothing process to correct the distortion while keeping the local topology consistent. The proposed method is applied on both artificial and real geographical data for evaluation.
Abstract: Transportation is one of the most fundamental
challenges of urban development in contemporary world. On the
other hand, sustainable urban development has received tremendous
public attention in the last few years. This trend in addition to other
factors such as energy cost, environmental concerns, traffic
congestion and the feeling of lack of belonging have contributed to
the development of pedestrian areas. The purpose of this paper is to
study the role of walkable streets in sustainable development of
cities. Accordingly, a documentary research through valid sources
has been utilized to substantiate this study. The findings demonstrate
that walking can lead to sustainable urban development from
physical, social, environmental, cultural, economic and political
aspects. Also, pedestrian areas –which are the main context of
walking- act as focal points of development in cities and have a great
effect on modifying and stimulating of their adjacent urban spaces.
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: Due to its geographical location, Iran is considered one of the earthquake-prone areas where the best way to decrease earthquake effects is supposed to be strengthening the buildings. Even though, one idea suggests that the use of adobe in constructing buildings be prohibited for its weak function especially in earthquake-prone areas, however, regarding ecological considerations, sustainability and other local skills, another idea pays special attention to adobe as one of the construction technologies which is popular among people. From the architectural and technological point of view, as strong sustainable building construction materials, compressed adobe construction materials make most of the construction in urban or rural areas ranging from small to big industrial buildings used to replace common earth blocks in traditional systems and strengthen traditional adobe buildings especially against earthquake. Mentioning efficient construction using compressed adobe system as a reliable replacement for traditional soil construction materials , this article focuses on the experiences of India in the fields of sustainable development of compressed adobe systems in the form of system in which the compressed soil is combined with cement, load bearing building with brick/solid concrete block system, brick system using rat trap bond, metal system with adobe infill and finally emphasizes on the use of these systems in the earthquake-struck city of Bam in Iran.
Abstract: This study examines the use of the persuasive strategy
of deixis and personalization in advertising slogans. This rhetorical/
stylistic and linguistic strategy has been found to be widely used in
advertising slogans for over a century. A total of five hundred
advertising slogans of multinational companies in both product and
service sectors were obtained. The analysis reveals the 3 main
components of this strategy as being deictic words, absolute
uniqueness and personal pronouns. The percentage and mean of the
use of the 3 components are tabulated. The findings show that
advertisers have used this persuasive strategy in creative ways to
persuade consumers to buy their products and services.
Abstract: This paper proposes a bi-objective model for the
facility location problem under a congestion system. The idea of the
model is motivated by applications of locating servers in bank
automated teller machines (ATMS), communication networks, and so
on. This model can be specifically considered for situations in which
fixed service facilities are congested by stochastic demand within
queueing framework. We formulate this model with two perspectives
simultaneously: (i) customers and (ii) service provider. The
objectives of the model are to minimize (i) the total expected
travelling and waiting time and (ii) the average facility idle-time.
This model represents a mixed-integer nonlinear programming
problem which belongs to the class of NP-hard problems. In addition,
to solve the model, two metaheuristic algorithms including nondominated
sorting genetic algorithms (NSGA-II) and non-dominated
ranking genetic algorithms (NRGA) are proposed. Besides, to
evaluate the performance of the two algorithms some numerical
examples are produced and analyzed with some metrics to determine
which algorithm works better.
Abstract: Software maintenance is extremely important activity in software development life cycle. It involves a lot of human efforts, cost and time. Software maintenance may be further subdivided into different activities such as fault prediction, fault detection, fault prevention, fault correction etc. This topic has gained substantial attention due to sophisticated and complex applications, commercial hardware, clustered architecture and artificial intelligence. In this paper we surveyed the work done in the field of software maintenance. Software fault prediction has been studied in context of fault prone modules, self healing systems, developer information, maintenance models etc. Still a lot of things like modeling and weightage of impact of different kind of faults in the various types of software systems need to be explored in the field of fault severity.
Abstract: Music Information Retrieval (MIR) and modern data mining techniques are applied to identify style markers in midi music for stylometric analysis and author attribution. Over 100 attributes are extracted from a library of 2830 songs then mined using supervised learning data mining techniques. Two attributes are identified that provide high informational gain. These attributes are then used as style markers to predict authorship. Using these style markers the authors are able to correctly distinguish songs written by the Beatles from those that were not with a precision and accuracy of over 98 per cent. The identification of these style markers as well as the architecture for this research provides a foundation for future research in musical stylometry.
Abstract: A theoretical approach to radiation damage evolution
is developed. Stable temporal behavior taking place in solids under
irradiation are examined as phenomena of self-organization in nonequilibrium
systems.
Experimental effects of temporal self-organization in solids under
irradiation are reviewed. Their essential common properties and
features are highlighted and analyzed.
Dynamical model to describe development of self-oscillation of
density of point defects under stationary irradiation is proposed. The
emphasis is the nonlinear couplings between rate of annealing and
density of defects that determine the kind and parameters of an
arising self-oscillation.
The field of parameters (defect generation rate and environment
temperature) at which self-oscillations develop is found. Bifurcation
curve and self-oscillation period near it is obtained.
Abstract: The argument that self-disclosure will change the
psychoanalytic process into a socio-cultural niche distorting the
therapeutic alliance and compromise therapeutic effectiveness is still
the widely held belief amongst many psychotherapists. This paper
considers the issues surrounding culture, disclosure and concealment
since they remain largely untheorized and clinically problematic. The
first part of the paper will critically examine the theory and practice
of psychoanalysis across cultures, and explore the reasons for
culturally diverse patients to conceal rather than disclose their
feelings and thoughts in the transference. This is followed by a
discussion on how immigrant analysts- anonymity is difficult to
maintain since diverse nationalities, language and accents provide
clues to the therapist-s and patient-s origins. Through personal
clinical examples of one the author-s (who is an immigrant) the paper
analyses the transference-countertransference paradigm and how it
reflects in the analyst-s self-revelation.
Abstract: This paper presents a Neural Network (NN) identification of icing parameters in an A340 aircraft and a reconfiguration technique to keep the A/C performance close to the performance prior to icing. Five aircraft parameters are assumed to be considerably affected by icing. The off-line training for identifying the clear and iced dynamics is based on the Levenberg-Marquard Backpropagation algorithm. The icing parameters are located in the system matrix. The physical locations of the icing are assumed at the right and left wings. The reconfiguration is based on the technique known as the control mixer approach or pseudo inverse technique. This technique generates the new control input vector such that the A/C dynamics is not much affected by icing. In the simulations, the longitudinal and lateral dynamics of an Airbus A340 aircraft model are considered, and the stability derivatives affected by icing are identified. The simulation results show the successful NN identification of the icing parameters and the reconfigured flight dynamics having the similar performance before the icing. In other words, the destabilizing icing affect is compensated.
Abstract: In this research, the use of light beam size to design the adjustable mirror bender is presented. The focused beam line characterized by its size towards the synchrotron light beam line is investigated. The COSMOSWorks is used in all simulation components of curvature adjustment system to analyze in finite element method. The results based on simulation covers the use of applied forces during adjustment of the mirror radius are presented.