Abstract: Electrical discharge machining (EDM) is well
established machining technique mainly used to machine complex
geometries on difficult-to-machine materials and high strength
temperature resistant alloys. In the present research, the objective is
to study the shape of the electrode and establish the application of
liquid nitrogen in reducing distortion of the electrode during
electrical discharge machining of M2 grade high speed steel using
copper electrodes. Study of roundness was performed on the
electrode to observe the shape of the electrode for both conventional
EDM and EDM with cryogenically cooled electrode. Scanning
Electron Microscope (SEM) has been used to study the shape of
electrode tip. The effect of various parameters such as discharge
current and pulse on time has been studied to understand the behavior
of distortion of electrode. It has been concluded that the shape
retention is better in case of liquid nitrogen cooled electrode.
Abstract: A numerical study has been conducted to investigate the influence of fin pitch and relative humidity on the heat transfer performance of the fin-and-tube heat exchangers having plain fin geometry under dehumidifying conditions. The analysis is done using the ratio between the heat transfer coefficients in totally wet conditions and those in totally dry conditions using the appropriate correlations for both dry and wet conditions. For a constant relative humidity, it is found that the heat transfer coefficient increases with the increase of the air frontal velocity. By contrast, the fin efficiency decreases when the face velocity is increased. Apparently, this phenomenon is attributed to the path of condensate drainage. For the influence of relative humidity, the results showed an increase in heat transfer performance and a decrease in wet fin efficiency when relative humidity increases. This is due to the higher amount of mass transfer encountered at higher relative humidity. However, it is found that the effect of fin pitch on the heat transfer performance depends strongly on the face velocity. At lower frontal velocity the heat transfer increases with fin pitch. Conversely, an increase in fin pitch gives lower heat transfer coefficients when air velocity is increased.
Abstract: This paper features the trajectory planning design of a indigenously developed 4-Axis SCARA robot which is used for doing successful robotic manipulation task in the laboratory. Once, a trajectory is being designed and given as input to the robot, the robot's gripper tip moves along that specified trajectory. Trajectories have to be designed in the work space only. The main idea of this paper is to design a continuous path trajectory model for the indigenously developed SCARA robot arm during its maneuvering from one point to another point (during pick and place operations) in a workspace avoiding all the obstacles in its path of motion.
Abstract: This paper proposes an adaptive sliding mode
controller which combines adaptive control and sliding
mode control to control a nonlinear robotic manipulator
with uncertain parameters. We use an adaptive algorithm
based on the concept of sliding mode control to alleviate the
chattering phenomenon of control input. Adaptive laws are
developed to obtain the gain of switching input and the
boundary layer parameters. The stability and convergence
of the robotic manipulator control system are guaranteed
by applying the Lyapunov theorem. Simulation results
demonstrate that the chattering of control input can be
alleviated effectively. The proposed controller scheme can
assure robustness against a large class of uncertainties and
achieve good trajectory tracking performance.
Abstract: We present a preliminary x-ray study on human-hair
microstructures for a health-state indicator, in particular a cancer
case. As an uncomplicated and low-cost method of x-ray technique,
the human-hair microstructure was analyzed by wide-angle x-ray
diffractions (XRD) and small-angle x-ray scattering (SAXS). The
XRD measurements exhibited the simply reflections at the d-spacing
of 28 Å, 9.4 Å and 4.4 Å representing to the periodic distance of the
protein matrix of the human-hair macrofibrous and the diameter and
the repeated spacing of the polypeptide alpha helixes of the
photofibrils of the human-hair microfibrous, respectively. When
compared to the normal cases, the unhealthy cases including to the
breast- and ovarian-cancer cases obtained higher normalized ratios of
the x-ray diffracting peaks of 9.4 Å and 4.4 Å. This likely resulted
from the varied distributions of microstructures by a molecular
alteration. As an elemental analysis by x-ray fluorescence (XRF), the
normalized quantitative ratios of zinc(Zn)/calcium(Ca) and
iron(Fe)/calcium(Ca) were determined. Analogously, both Zn/Ca and
Fe/Ca ratios of the unhealthy cases were obtained higher than both of
the normal cases were. Combining the structural analysis by XRD
measurements and the elemental analysis by XRF measurements
exhibited that the modified fibrous microstructures of hair samples
were in relation to their altered elemental compositions. Therefore,
these microstructural and elemental analyses of hair samples will be
benefit to associate with a diagnosis of cancer and genetic diseases.
This functional method would lower a risk of such diseases by the
early diagnosis. However, the high-intensity x-ray source, the highresolution
x-ray detector, and more hair samples are necessarily
desired to develop this x-ray technique and the efficiency would be
enhanced by including the skin and fingernail samples with the
human-hair analysis.
Abstract: Objective of this study was to study and compare the effectiveness of inspectors who had different workloads for feed forward and feedback training. The visual search task was simulated to search for specified alphabets called defects. These defects were included of four alphabets in Thai and English such as s ภ, ถ, X, and V with different background. These defects were combined in the specified alphabets and were given the different three backgrounds i.e., Thai, English, and mixed English and Thai alphabets. Sixty students were chosen as a sample in this study and test for final selection subject. Finally, five subjects were taken into testing process. They were asked to search for defects after they were provided basic information. Experiment design was used factorial design and subjects were trained for feed forward and the feedback training. The results show that both trainings were affected on mean search time. It was also found that the feedback training can increase the effectiveness of visual inspectors rather than the feed forward training significantly different at the level of .05
Abstract: A novel application of neural network approach to
fault classification and fault location of Medium voltage cables is
demonstrated in this paper. Different faults on a protected cable
should be classified and located correctly. This paper presents the use
of neural networks as a pattern classifier algorithm to perform these
tasks. The proposed scheme is insensitive to variation of different
parameters such as fault type, fault resistance, and fault inception
angle. Studies show that the proposed technique is able to offer high
accuracy in both of the fault classification and fault location tasks.
Abstract: The research was designed to examine the relationship
between the development of muscle fatigue and the effect it has on
sport performance, specifically during maximal voluntary
contraction. This kind of this investigation using simultaneous
electrophysiological and mechanical recordings, based on advanced
mathematical processing, allows us to get parameters, and indexes in
a short time, and finally, the mapping to use for the thorough
investigation of the muscle contraction force, respectively the
phenomenon of local muscle fatigue, both for athletes and other
subjects.
Abstract: This work presents a theoretical investigation of the
simultaneous absorption of CO2 and H2S into aqueous solutions of
MDEA and DEA. In this process the acid components react
with the basic alkanolamine solution via an exothermic,
reversible reaction in a gas/liquid absorber. The use of amine
solvents for gas sweetening has been investigated using
process simulation programs called HYSYS and ASPEN. We
use Electrolyte NRTL and Amine Package and Amines
(experimental) equation of state. The effects of temperature and
circulation rate and amine concentration and packed column and
murphree efficiency on the rate of absorption were studied.
When lean amine flow and concentration increase, CO2 and H2S
absorption increase too. With the improvement of inlet amine
temperature in absorber, CO2 and H2S penetrate to upper stages of
absorber and absorption of acid gases in absorber decreases. The CO2
concentration in the clean gas can be greatly influenced by the
packing height, whereas for the H2S concentration in the clean gas the
packing height plays a minor role. HYSYS software can not
estimate murphree efficiency correctly and it applies the same
contributions in all diagrams for HYSYS software. By
improvement in murphree efficiency, maximum temperature
of absorber decrease and the location of reaction transfer to the
stages of bottoms absorber and the absorption of acid gases
increase.
Abstract: Unmanned Aerial Vehicles (UAVs) have gained tremendous importance, in both Military and Civil, during first decade of this century. In a UAV, onboard computer (autopilot) autonomously controls the flight and navigation of the aircraft. Based on the aircraft role and flight envelope, basic to complex and sophisticated controllers are used to stabilize the aircraft flight parameters. These controllers constitute the autopilot system for UAVs. The autopilot systems, most commonly, provide lateral and longitudinal control through Proportional-Integral-Derivative (PID) controllers or Phase-lead or Lag Compensators. Various techniques are commonly used to ‘tune’ gains of these controllers. Some techniques used are, in-flight step-by-step tuning, software-in-loop or hardware-in-loop tuning methods. Subsequently, numerous in-flight tests are required to actually ‘fine-tune’ these gains. However, an optimization-based tuning of these PID controllers or compensators, as presented in this paper, can greatly minimize the requirement of in-flight ‘tuning’ and substantially reduce the risks and cost involved in flight-testing.
Abstract: In order to better understand the performance of
screen channel liquid acquisition devices (LADs) in liquid oxygen (LOX), a computational fluid dynamics (CFD) simulation of LOX passing through a LAD screen channel was conducted. In the
simulation, the screen is taken as a 'porous jump' where the pressure
drop across the screen depends on the incoming velocity and is formulated by Δp = Av + Bv2
. The CFD simulation reveals the importance of the pressure losses due to the flow entering from
across the screen and impacting and merging with the channel flow
and the vortices in the channel to the cumulative flow resistance. In fact, both the flow resistance of flows impact and mergence and the
resistance created by vortices are much larger than the friction and dynamic pressure losses in the channel and are comparable to the
flow resistance across the screen. Therefore, these resistances in the
channel must be considered as part of the evaluation for the LAD
channel performance. For proper operation of a LAD in LOX these resistances must be less than the bubble point pressure for the screen
channel in LOX. The simulation also presents the pressure and velocity distributions within the LAD screen channel, expanding the understanding of the fluid flow characteristics within the channel.
Abstract: Business Process Reengineering (BPR) is an essential tool before an information system project implementation. Enterprise Resource Planning (ERP) projects definitely require the standardization and fixation of business processes from customer order to shipment. Therefore, ERP implementations are well proven to be coupled with BPR, although the extend and timing of BPR with respect to ERP implementation differ. This study aims at analyzing the effects of BPR on ERP implementation success. Basing on two Turkish ERP implementations in pharmaceutical sector, a comparative study is performed. One of the ERP implementations took place after a BPR implementation, whereas the other implementation was without a prior BPR application. Both implementations have been realized with the same consultant team, the case with prior BPR implementation going live first. The results of the case study reveal that if business processes are not optimized and improved before an ERP implementation, ERP live system would face with disharmony problems of processes and processes automated by ERP. This suggests a definite precedence relationship between BPR and ERP applications
Abstract: In studies on psychological health and children-s personality development and in researches on emotional distresses, children-s behavioral disorders associated with mother deprivation, are known as the major cause of mental disorders. Therefore, for identification of children-s attachment styles in nursery-s children are of significant importance. For this purpose, to compare the attachment styles between children of nursery with those provided care by their families, the Separation Anxiety Test (SAT) of Slough and et al was administered on 72 children (36 in nursery and 36 family-cared). The results indicated, almost half of children in both groups have insecure attachment styles. Tendency ratio of both groups of children towards Secure and Ambivalent Insecure styles are almost the same. However the avoidant style of attachment in children of nursery is more than those provided care by their families. The children under family care compared to the children of nursery, in the situations of separation from their mothers in the first day of school and sleeping in their room, have shown more self reliance.
Abstract: The performance of ground to deep space optical
communication systems is degraded by distortion of the beam as it
propagates through the turbulent atmosphere. Turbulence causes
fluctuations in the intensity of the received signal which ultimately
affects the acquisition time required to acquire and locate the spaceborne
target using narrow laser beam. In this paper, performance of
free-space optical (FSO) communication system in atmospheric
turbulence has been analyzed in terms of acquisition time for
coherent and non-coherent modulation schemes. Numerical results
presented in graphical and tabular forms show that the acquisition
time increases with the increase in turbulence level. This is true for
both schemes. The BPSK has lowest acquisition time among all
schemes. In non-coherent schemes, M-PPM performs better than the
other schemes. With the increase in M, acquisition time becomes
lower, but at the cost of increase in system complexity.
Abstract: Studies were carried out on the comparative study of the production of Avicelase enzyme using sugarcane bagasse-SCB in two different statuses (i.e. treated and untreated SCB) by thermophilic Geobacillus stearothermophilus at 50ºC. Only four thermophilic bacterial isolates were isolated and assayed for Avicelase production using UntSCB and TSCB. Only one isolate selected as most potent and identified as G. stearothermophilus used in this study. A specific endo-β-1,4-D-glucanase (Avicelase EC 3.2.1.91) was partially purified from a thermophilic bacterial strain was isolated from different soil samples when grown on cellulose enrichment SCB substrate as the sole carbon source. Results shown that G. stearothermophilus was the better Avicelase producer strain. Avicelase had an optimum pH and temperature 7.0 and 50ºC for both UntSCB and TSCB and exhibited good pH stability between "5-8" and "4-9", however, good temperature stability between (30-80ºC) for UntSCB and TSCB, respectively. Other factors affecting the production of Avicelase were compared (i.e. SCB concentration, inoculum size and different incubation periods), all results observed and obtained were revealed that the TSCB was exhibited maximal enzyme activity in comparison with the results obtained from UntSCB, so, the TSCB was enhancing the Avicelase production.
Abstract: Urban problems are problems of organized complexity. Thus, many models and scientific methods to resolve urban problems are failed. This study is concerned with proposing of a fuzzy system driven approach for classification and solving urban problems. The proposed study investigated mainly the selection of the inputs and outputs of urban systems for classification of urban problems. In this research, five categories of urban problems, respect to fuzzy system approach had been recognized: control, polytely, optimizing, open and decision making problems. Grounded Theory techniques were then applied to analyze the data and develop new solving method for each category. The findings indicate that the fuzzy system methods are powerful processes and analytic tools for helping planners to resolve urban complex problems. These tools can be successful where as others have failed because both incorporate or address uncertainty and risk; complexity and systems interacting with other systems.
Abstract: This paper presents a case study that uses processoriented
simulation to identify bottlenecks in the service delivery
system in an emergency department of a hospital in the United Arab
Emirates. Using results of the simulation, response surface models
were developed to explain patient waiting time and the total time
patients spend in the hospital system. Results of the study could be
used as a service improvement tool to help hospital management in
improving patient throughput and service quality in the hospital
system.
Abstract: Fishing has always been an essential component of
the Polynesians- life. Fishhooks, mostly in pearl shell, found during
archaeological excavations are the artifacts related to this activity the
most numerous. Thanks to them, we try to reconstruct the ancient
techniques of resources exploitation, inside the lagoons and offshore.
They can also be used as chronological and cultural indicators. The
shapes and dimensions of these artifacts allow comparisons and
classifications used in both functional approach and chrono-cultural
perspective. Hence it is very important for the ethno-archaeologists
to dispose of reliable methods and standardized measurement of
these artifacts. Such a reliable objective and standardized method
have been previously proposed. But this method cannot be envisaged
manually because of the very important time required to measure
each fishhook manually and the quantity of fishhooks to measure
(many hundreds). We propose in this paper a detailed acquisition
protocol of fishhooks and an automation of every step of this method.
We also provide some experimental results obtained on the fishhooks
coming from three archaeological excavations sites.
Abstract: This paper investigates the effects of lubrication on
the quantity of heat emission of two spur gear. System with and
without lubrication effected on the quantity of heat induced on the
gear box (oil - bearings – gears). Both of lubrication and speed of
motor are affected on the performance of gears. Research investigated
the lubrication on the system with and without loading as well as the
wear of gears and bearing's conditions. Gear box investigated
includes the motor, pump, two spur gears, two shafts; speed change
used pulleys and belts. Load used equal one weight ones of gear.
Lubrication mechanism used jet system (upper and lower jet). Gear
box we used system of jet lubrication is perpendicular direction of
the contact line between two teeth. Results appeared in this work that
the lubrication is the vital parameter which is affected on the
performance and durability of gears and bearings. In macroscopic
observation, we noted that damage of bearings happened during the
absence of lubrication as well as abrasive of wear of teeth. Higher
speed of motor without lubrication increased the noise, but in the
presence of lubrication was decreased.
Abstract: Given bipartite graphs H1 and H2, the bipartite Ramsey number b(H1;H2) is the smallest integer b such that any subgraph G of the complete bipartite graph Kb,b, either G contains a copy of H1 or its complement relative to Kb,b contains a copy of H2. It is known that b(K2,2;K2,2) = 5, b(K2,3;K2,3) = 9, b(K2,4;K2,4) = 14 and b(K3,3;K3,3) = 17. In this paper we study the case that both H1 and H2 are even cycles, prove that b(C2m;C2n) ≥ m + n - 1 for m = n, and b(C2m;C6) = m + 2 for m ≥ 4.