Abstract: A climate dependent model is proposed to simulate
the population of Aedes aegypti mosquito. In developing the model,
average temperature of Shah Alam, Malaysia was used to determine
the development rate of each stage of the life cycle of mosquito.
Rainfall dependent function was proposed to simulate the hatching
rate of the eggs under several assumptions. The proposed transition
matrix was obtained and used to simulate the population of eggs,
larvae, pupae and adults mosquito. It was found that the peak of
mosquito abundance comes during a relatively dry period following a
heavy rainfall. In addition, lag time between the peaks of mosquito
abundance and dengue fever cases in Shah Alam was estimated.
Abstract: Fertilization plays an important role in crop growth and soil improvement. This study was conducted to determine the best fertilization system for wheat production. Experiments were arranged in a complete block design with three replications in two years. Main plots consisted of six methods of fertilization including (N1): farmyard manure; (N2): compost; (N3): chemical fertilizers; (N4): farmyard manure + compost; (N5): farmyard manure + compost + chemical fertilizers and (N6): control were arranged in sub plots. The addition of compost or farm yard manure significantly increased the soil microbial biomass carbon in comparison to the chemical fertilizer. The dehydrogenase, phosphatase and urease activities in the N3 treatment were significantly lower than in the farm yard manure and compost treatments.
Abstract: Using 1km grid datasets representing monthly mean
precipitation, monthly mean temperature, and dry matter production
(DMP), we considered the regional plant production ability in
Southeast and South Asia, and also employed pixel-by-pixel
correlation analysis to assess the intensity of relation between climate
factors and plant production. While annual DMP in South Asia was
approximately less than 2,000kg, the one in most part of Southeast
Asia exceeded 2,500 - 3,000kg. It suggested that plant production in
Southeast Asia was superior to South Asia, however, Rain-Use
Efficiency (RUE) representing dry matter production per 1mm
precipitation showed that inland of Indochina Peninsula and India
were higher than islands in Southeast Asia. By the results of
correlation analysis between climate factors and DMP, while the area
in most parts of Indochina Peninsula indicated negative correlation
coefficients between DMP and precipitation or temperature, the area
in Malay Peninsula and islands showed negative correlation to
precipitation and positive one to temperature, and most part of India
dominating South Asia showed positive to precipitation and negative
to temperature. In addition, the areas where the correlation coefficients
exceeded |0.8| were regarded as “susceptible" to climate factors, and
the areas smaller than |0.2| were “insusceptible". By following the
discrimination, the map implying expected impacts by climate change
was provided.
Abstract: Voice over Internet Protocol (VoIP) application or commonly known as softphone has been developing an increasingly large market in today-s telecommunication world and the trend is expected to continue with the enhancement of additional features. This includes leveraging on the existing presence services, location and contextual information to enable more ubiquitous and seamless communications. In this paper, we discuss the concept of seamless session transfer for real-time application such as VoIP and IPTV, and our prototype implementation of such concept on a selected open source VoIP application. The first part of this paper is about conducting performance evaluation and assessments across some commonly found open source VoIP applications that are Ekiga, Kphone, Linphone and Twinkle so as to identify one of them for implementing our design of seamless session transfer. Subjective testing has been carried out to evaluate the audio performance on these VoIP applications and rank them according to their Mean Opinion Score (MOS) results. The second part of this paper is to discuss on the performance evaluations of our prototype implementation of session transfer using Linphone.
Abstract: The demand on High voltage (HV) infrastructures is growing due to the corresponding growth in industries and population. Many areas are being developed and therefore require additional electrical power to comply with the demand. Substation upgrade is one of the rapid solutions to ensure the continuous supply of power to customers. This upgrade requires civil modifications to structures and fences. The civil work requires excavation and steel works that may create unsafe touch conditions. This paper presents a brief theoretical overview of the touch voltage inside and around substations and uses CDEGS software to simulate a case study.
Abstract: Warranty is a powerful marketing tool for the
manufacturer and a good protection for both the manufacturer and the
customer. However, warranty always involves additional costs to the
manufacturer, which depend on product reliability characteristics and
warranty parameters. This paper presents an approach to optimisation
of warranty parameters for known product failure distribution to
reduce the warranty costs to the manufacturer while retaining the
promotional function of the warranty. Combination free replacement
and pro-rata warranty policy is chosen as a model and the length of
free replacement period and pro-rata policy period are varied, as well
as the coefficients that define the pro-rata cost function. Multiparametric
warranty optimisation is done by using genetic algorithm.
Obtained results are guideline for the manufacturer to choose the
warranty policy that minimises the costs and maximises the profit.
Abstract: The use of amine mixtures employing
methyldiethanolamine (MDEA), monoethanolamine (MEA), and diethanolamine (DEA) have been investigated for a variety of cases
using a process simulation program called HYSYS. The results show that, at high pressures, amine mixtures have little or no advantage in the cases studied. As the pressure is lowered, it becomes more difficult for MDEA to meet residual gas requirements and mixtures can usually improve plant performance. Since the CO2 reaction rate
with the primary and secondary amines is much faster than with
MDEA, the addition of small amounts of primary or secondary amines to an MDEA based solution should greatly improve the overall reaction rate of CO2 with the amine solution. The addition of MEA caused the CO2 to be absorbed more strongly in the upper portion of the column than for MDEA along. On the other hand,
raising the concentration for MEA to 11%wt, CO2 is almost
completely absorbed in the lower portion of the column. The addition of MEA would be most advantageous.
Thus, in areas where MDEA cannot meet the residual gas
requirements, the use of amine mixtures can usually improve the plant
performance.
Abstract: In present article the model of Blended Learning, its advantage at foreign language teaching, and also some problems that can arise during its use are considered. The Blended Learning is a special organization of learning, which allows to combine classroom work and modern technologies in electronic distance teaching environment. Nowadays a lot of European educational institutions and companies use such technology. Through this method: student gets the opportunity to learn in a group (classroom) with a teacher and additionally at home at a convenient time; student himself sets the optimal speed and intensity of the learning process; this method helps student to discipline himself and learn to work independently.
Abstract: A structural study of an aqueous electrolyte whose
experimental results are available. It is a solution of LiCl-6H2O type
at glassy state (120K) contrasted with pure water at room temperature
by means of Partial Distribution Functions (PDF) issue from neutron
scattering technique. Based on these partial functions, the Reverse
Monte Carlo method (RMC) computes radial and angular correlation
functions which allow exploring a number of structural features of
the system. The obtained curves include some artifacts. To remedy
this, we propose to introduce a screened potential as an additional
constraint. Obtained results show a good matching between
experimental and computed functions and a significant improvement
in PDFs curves with potential constraint. It suggests an efficient fit of
pair distribution functions curves.
Abstract: The major building block of most elliptic curve cryptosystems
are computation of multi-scalar multiplication. This paper
proposes a novel algorithm for simultaneous multi-scalar multiplication,
that is by employing addition chains. The previously known
methods utilizes double-and-add algorithm with binary representations.
In order to accomplish our purpose, an efficient empirical
method for finding addition chains for multi-exponents has been
proposed.
Abstract: It is necessary to evaluate the bridges conditions and
strengthen bridges or parts of them. The reinforcement necessary due
to some reasons can be summarized as: First, a changing in use of
bridge could produce internal forces in a part of structural which
exceed the existing cross-sectional capacity. Second, bridges may
also need reinforcement because damage due to external factors
which reduced the cross-sectional resistance to external loads. One of
other factors could listed here its misdesign in some details, like
safety of bridge or part of its.This article identify the design demands
of Qing Shan bridge located in is in Heilongjiang Province He gang -
Nen Jiang Road 303 provincial highway, Wudalianchi area, China, is
an important bridge in the urban areas. The investigation program
was include the observation and evaluate the damage in T- section
concrete beams , prestressed concrete box girder bridges section in
additional evaluate the whole state of bridge includes the pier ,
abutments , bridge decks, wings , bearing and capping beam, joints,
........etc. The test results show that the bridges in general structural
condition are good. T beam span No 10 were observed, crack
extended upward along the ribbed T beam, and continue to the T
beam flange. Crack width varying between 0.1mm to 0.4mm, the
maximum about 0.4mm. The bridge needs to be improved flexural
bending strength especially at for T beam section.
Abstract: In this paper, to optimize the “Characteristic Straight Line Method" which is used in the soil displacement analysis, a “best estimate" of the geodetic leveling observations has been achieved by taking in account the concept of 'Height systems'. This concept has been discussed in detail and consequently the concept of “height". In landslides dynamic analysis, the soil is considered as a mosaic of rigid blocks. The soil displacement has been monitored and analyzed by using the “Characteristic Straight Line Method". Its characteristic components have been defined constructed from a “best estimate" of the topometric observations. In the measurement of elevation differences, we have used the most modern leveling equipment available. Observational procedures have also been designed to provide the most effective method to acquire data. In addition systematic errors which cannot be sufficiently controlled by instrumentation or observational techniques are minimized by applying appropriate corrections to the observed data: the level collimation correction minimizes the error caused by nonhorizontality of the leveling instrument's line of sight for unequal sight lengths, the refraction correction is modeled to minimize the refraction error caused by temperature (density) variation of air strata, the rod temperature correction accounts for variation in the length of the leveling rod' s Invar/LO-VAR® strip which results from temperature changes, the rod scale correction ensures a uniform scale which conforms to the international length standard and the introduction of the concept of the 'Height systems' where all types of height (orthometric, dynamic, normal, gravity correction, and equipotential surface) have been investigated. The “Characteristic Straight Line Method" is slightly more convenient than the “Characteristic Circle Method". It permits to evaluate a displacement of very small magnitude even when the displacement is of an infinitesimal quantity. The inclination of the landslide is given by the inverse of the distance reference point O to the “Characteristic Straight Line". Its direction is given by the bearing of the normal directed from point O to the Characteristic Straight Line (Fig..6). A “best estimate" of the topometric observations was used to measure the elevation of points carefully selected, before and after the deformation. Gross errors have been eliminated by statistical analyses and by comparing the heights within local neighborhoods. The results of a test using an area where very interesting land surface deformation occurs are reported. Monitoring with different options and qualitative comparison of results based on a sufficient number of check points are presented.
Abstract: The first generation of Mobile Agents based Intrusion
Detection System just had two components namely data collection
and single centralized analyzer. The disadvantage of this type of
intrusion detection is if connection to the analyzer fails, the entire
system will become useless. In this work, we propose novel hybrid
model for Mobile Agent based Distributed Intrusion Detection
System to overcome the current problem. The proposed model has
new features such as robustness, capability of detecting intrusion
against the IDS itself and capability of updating itself to detect new
pattern of intrusions. In addition, our proposed model is also capable
of tackling some of the weaknesses of centralized Intrusion Detection
System models.
Abstract: In this paper, the signal transmission analysis of the
semicircle-shaped via structure for the differential pairs is presented in
the frequency range up to 10 GHz. In order to improve the signal
transmission properties in the differential pairs, single via is separated
centrally into two semicircle-shaped sections, which are
interconnected with the traces of differential pairs respectively. This
via structure make possible to route differential pairs using only one
via. In addition, it can improve impedance discontinuity around its
region and then enhance the signal transmission properties in the
differential pairs. The electrical analysis such as S-parameter
calculation and eye diagram simulation has been performed to
investigate the improvement of the signal transmission property in the
differential pairs with new via structure.
Abstract: The social force model which belongs to the
microscopic pedestrian studies has been considered as the supremacy
by many researchers and due to the main feature of reproducing the
self-organized phenomena resulted from pedestrian dynamic. The
Preferred Force which is a measurement of pedestrian-s motivation to
adapt his actual velocity to his desired velocity is an essential term on
which the model was set up. This Force has gone through stages of
development: first of all, Helbing and Molnar (1995) have modeled
the original force for the normal situation. Second, Helbing and his
co-workers (2000) have incorporated the panic situation into this
force by incorporating the panic parameter to account for the panic
situations. Third, Lakoba and Kaup (2005) have provided the
pedestrians some kind of intelligence by incorporating aspects of the
decision-making capability. In this paper, the authors analyze the
most important incorporations into the model regarding the preferred
force. They make comparisons between the different factors of these
incorporations. Furthermore, to enhance the decision-making ability
of the pedestrians, they introduce additional features such as the
familiarity factor to the preferred force to let it appear more
representative of what actually happens in reality.
Abstract: Combined experimental and computational analysis of
hygrothermal performance of an interior thermal insulation system
applied on a brick wall is presented in the paper. In the experimental
part, the functionality of the insulation system is tested at simulated
difference climate conditions using a semi-scale device. The
measured temperature and relative humidity profiles are used for the
calibration of computer code HEMOT that is finally applied for a
long-term hygrothermal analysis of the investigated structure.
Abstract: In this paper, an authentication system using keystroke dynamics is presented. We introduced pressure sensing for the improvement of the accuracy of measurement and durability against intrusion using key-logger, and so on, however additional instrument is needed. As the result, it has been found that the pressure sensing is also effective for estimation of real moment of keystroke.
Abstract: Sedimentation in reservoirs and the corresponding
loss of storage capacity is one of the most serious problems in dam
engineering. Pressurized flushing, a way to remove sediments from the reservoir, is flushing under a pressurized flow condition and
nearly constant water level. Pressurized flushing has only local
effects around the outlet. Sediment in the vicinity of the outlet openings is scoured and a funnel shaped crater is created. In this study, the temporal development of flushing cone under various
hydraulic conditions was studied experimentally. Time variations of
parameters such as maximum length and width of flushing and also
depth of scouring cone was measured. Results indicated that an
increase in flow velocity (and consequently in Froude number)
established new hydraulically conditions for flushing mechanism and
so a sudden growth was observed in the amount of sediment released
and also scouring dimenssions. In addition, a set of nondimensional
relationships were identified for temporal variations of flushing scour
dimenssions, which can eventuallt be used to estimate the development of flushing cone.
Abstract: In recent years, environment regulation forcing
manufactures to consider recovery activity of end-of- life products
and/or return products for refurbishing, recycling,
remanufacturing/repair and disposal in supply chain management. In
this paper, a mathematical model is formulated for single product
production-inventory system considering remanufacturing/reuse of
return products and rate of return products follows a demand like
function, dependent on purchasing price and acceptance quality level.
It is useful in decision making to determine whether to go for
remanufacturing or disposal of returned products along with newly
produced products to satisfy a stationary demand. In addition, a
modified genetic algorithm approach is proposed, inspired by particle
swarm optimization method. Numerical analysis of the case study is
carried out to validate the model.
Abstract: The study describes chitosan membrane platform
modified with nanostructure pattern which using nanotechnology to
fabricate. The cell-substrate interaction between neuro-2a neuroblasts
cell lines and chitosan membrane (flat, nanostructure and
nanostructure pattern types) was investigated. The adhered
morphology of neuro-2a cells depends on the topography of chitosan
surface. We have found that neuro-2a showed different morphogenesis
when cells adhered on flat and nanostructure chitosan membrane. The
cell projected area of neuro-2a on flat chitosan membrane is larger
than on nanostructure chitosan membrane. In addition, neuro-2a cells
preferred to adhere on flat chitosan surface region than on
nanostructure chitosan membrane to immobilize and differentiation.
The experiment suggests surface topography can be used as a critical
mechanism to isolate group of neuro-2a to a particular rectangle area
on chitosan membrane. Our finding will provide a platform to take
patch clamp to record electrophysiological behavior about neurons in
vitro in the future.