Abstract: Male factor infertility due to endocrine disturbances
such as abnormalities in prolactin levels are encountered in a
significant proportion. This case control study was carried out to
determine the effects of prolactin on the male reproductive tract,
using 200 male white rats. The rats were maintained as the control
group (G1), hypoprolactinaemic group (G2), 3 hyperprolactinaemic
groups induced using oral largactil (G3), low dose fluphenazine (G4)
and high dose fluphenazine (G5). After 100 days, rats were subjected
to serum prolactin (PRL) level measurements and for basic seminal
fluid analysis (BSA). The difference between serum PRL
concentrations of rats in G2, G3, G4 and G5 as compared to the
control group were highly significant by Student’s t-test (p
Abstract: Concerns on corrosion and effective coating
protection of double hull tankers and bulk carriers in service have
been raised especially in water ballast tanks (WBTs). Test
protocols/methodologies specifically that which is incorporated in the
International Maritime Organisation (IMO), Performance Standard
for Protective Coatings for Dedicated Sea Water ballast tanks (PSPC)
are being used to assess and evaluate the performance of the coatings
for type approval prior to their application in WBTs. However, some
of the type approved coatings may be applied as very thick films to
less than ideally prepared steel substrates in the WBT. As such films
experience hygrothermal cycling from operating and environmental
conditions, they become embrittled which may ultimately result in
cracking. This embrittlement of the coatings is identified as an
undesirable feature in the PSPC but is not mentioned in the test
protocols within it. There is therefore renewed industrial research
aimed at understanding this issue in order to eliminate cracking and
achieve the intended coating lifespan of 15 years in good condition.
This paper will critically review test protocols currently used for
assessing and evaluating coating performance, particularly the IMO
PSPC.
Abstract: This paper presents the voltage problem location
classification using performance of Least Squares Support Vector
Machine (LS-SVM) and Learning Vector Quantization (LVQ) in
electrical power system for proper voltage problem location
implemented by IEEE 39 bus New- England. The data was collected
from the time domain simulation by using Power System Analysis
Toolbox (PSAT). Outputs from simulation data such as voltage, phase
angle, real power and reactive power were taken as input to estimate
voltage stability at particular buses based on Power Transfer Stability
Index (PTSI).The simulation data was carried out on the IEEE 39 bus
test system by considering load bus increased on the system. To verify
of the proposed LS-SVM its performance was compared to Learning
Vector Quantization (LVQ). The results showed that LS-SVM is faster
and better as compared to LVQ. The results also demonstrated that the
LS-SVM was estimated by 0% misclassification whereas LVQ had
7.69% misclassification.
Abstract: In Egypt, girls have traditionally been educationally
disadvantaged. This disadvantage, however, has been focused on the
failure to enter school. Increasingly it is recognized that girls who
ever-enroll are at least as likely to complete primary and secondary
education as boys. Still the belief persists that girls, especially those
from poor families, will be disadvantaged in terms of school
expenditures and the transitions to secondary and higher education.
We examine expenditures on tutoring during the final year of
preparatory school, and the transition to specific tracks of secondary
education. Tests during the last year of preparatory largely determine
a student’s educational future. Results show that girls, even girls from
poor families, are not disadvantaged in terms of expenditures,
whether for tutoring, fees or general expenses. Moreover, girls are
more likely than boys to advance to general secondary education, the
track that leads to higher education.
Abstract: This study models the use of transcutaneous electrical
nerve stimulation on skin with a disk electrode in order to simulate
tissue damage. The current density distribution above a disk electrode
is known to be a dynamic and non-uniform quantity that is intensified
at the edges of the disk. The non-uniformity is subject to change
through using various electrode geometries or stimulation methods.
One of these methods known as edge-retarded stimulation has shown
to reduce this edge enhancement. Though progress has been made in
modeling the behavior of a disk electrode, little has been done to test
the validity of these models in simulating the actual heat transfer
from the electrode. This simulation uses finite element software to
couple the injection of current from a disk electrode to heat transfer
described by the Pennesbioheat transfer equation. An example
application of this model is studying an experimental form of
stimulation, known as edge-retarded stimulation. The edge-retarded
stimulation method will reduce the current density at the edges of the
electrode. It is hypothesized that reducing the current density edge
enhancement effect will, in turn, reduce temperature change and
tissue damage at the edges of these electrodes. This study tests this
hypothesis as a demonstration of the capabilities of this model. The
edge-retarded stimulation proved to be safer after this simulation. It is
shown that temperature change and the fraction of tissue necrosis is
much greater in the square wave stimulation. These results bring
implications for changes of procedures in transcutaneous electrical
nerve stimulation and transcutaneous spinal cord stimulation as well.
Abstract: This paper presents the variation of the dynamic
characteristics of a spindle with the change of bearing preload. The
correlations between the variation of bearing preload and fundamental
modal parameters were first examined by conducting vibration tests on
physical spindle units. Experimental measurements show that the
dynamic compliance and damping ratio associated with the
dominating modes were affected to vary with variation of the bearing
preload. When the bearing preload was slightly deviated from a
standard value, the modal frequency and damping ability also vary to
different extent, which further enable the spindle to perform with
different compliance. For the spindle used in this study, a standard
preload value set on bearings would enable the spindle to behave a
higher stiffness as compared with others with a preload variation. This
characteristic can be served as a reference to examine the variation of
bearing preload of spindle in assemblage or operation.
Abstract: High temperature deformation behavior of cast
Fe-20Cr-5Al alloy has been investigated in this study by performing
tensile and compression tests at temperatures from 1100 to 1200oC.
Rectangular ingots of which the dimensions were 300×300×100 in
millimeter were cast using vacuum induction melting. Phase
equilibrium was calculated using the FactSage®, thermodynamic
software and database. Tensile strength of cast Fe-20Cr-5Al alloy was
4 MPa at 1200oC. With temperature decreased, tensile strength
increased rapidly and reached up to 13 MPa at 1100oC. Elongation
also increased from 18 to 80% with temperature decreased from
1200oC to 1100oC. Microstructure observation revealed that M23C6
carbide was precipitated along the grain boundary and within the
matrix.
Abstract: Enzyme activity was evaluated in the intestine of
juvenile dourado (Salminus brasiliensis) fed with diets containing 0,
10 or 20% of lyophilized bovine colostrum (LBC) inclusion for either
30 or 60 days. The intestinal enzymes acid and alkaline phosphatase
(ACP and ALP, respectively), non-specific esterase (NSE), lipase
(LIP), dipeptidyl aminopeptidase IV (DAP IV) and leucine
aminopeptidase (LAP) were studied using histochemistry in four
intestinal segments (S1, S2, S3 and posterior intestine). Weak
proteolitic activity was observed in all intestinal segments for DAP
IV and LAP. The activity of NSE and LIP was also weak in all
intestines, except for the moderate activity of NSE in the S2 of 20%
LBC group after 30 days and in the S1 of 0% LBC group after 60
days. The ACP was detected only in the S2 and S3 of the 10% LBC
group after 30 days. Moderate and strong staining was observed in
the first three intestinal segments for ALP and weak activity in the
posterior intestine. The activity of DAP IV, LAP and ALP were also
present in the cytoplasm of the enterocytes. In the present results,
bovine colostrum feeding did not cause alterations in activity of
intestinal enzymes.
Abstract: This study investigates the effect of moisture
conditioning on the Indirect Tensile Strength (ITS) of asphalt
concrete. As a first step, cylindrical samples of 100 mm diameter and
50 mm thick were prepared using a Superpave gyratory compactor.
Next, the samples were conditioned using Moisture Induced
Susceptibility Test (MIST) device at different numbers of moisture
conditioning cycles. In the MIST device, samples are subjected water
pressure through the sample pores cyclically. The MIST conditioned
samples were tested for ITS. Results show that the ITS does not
change significantly with MIST conditioning at the specific pressure
and cycles adopted in this study.
Abstract: In remote sensing, shadow causes problems in many
applications such as change detection and classification. It is caused
by objects which are elevated, thus can directly affect the accuracy of
information. For these reasons, it is very important to detect shadows
particularly in urban high spatial resolution imagery which created a
significant problem. This paper focuses on automatic shadow
detection based on a new spectral index for multispectral imagery
known as Shadow Detection Index (SDI). The new spectral index
was tested on different areas of WorldView-2 images and the results
demonstrated that the new spectral index has a massive potential to
extract shadows with accuracy of 94% effectively and automatically.
Furthermore, the new shadow detection index improved road
extraction from 82% to 93%.
Abstract: Construction in Finland is focusing increasingly on
renovation instead of conventional new construction, and this trend
will continue to grow in the coming years and decades. Renovation of
the large number of suburban residential apartment buildings built in
the 1960s and 1970s poses a particular challenge. However,
renovation projects are demanding for the residents of these
buildings, since they usually are uninitiated in construction issues. On
the other hand, renovation projects generally apply the operating
models of new construction.
Nevertheless, the residents of an existing residential apartment
building are some of the best experts on the site. Thus, in this
research project we applied a relational model in developing and
testing at case sites a planning process that employs interactive
planning methods. Current residents, housing company managers, the
city zoning manager, the contractor’s and prefab element supplier’s
representatives, professional designers and researchers all took part in
the planning. The entire interactive planning process progressed
phase by phase as the participants’ and designers’ concerted
discussion and ideation process, so that the end result was a
renovation plan desired by the residents.
Abstract: The study examines the influence of marital status on
consumers of products and services using blogs as a source of
information. A pre-designed questionnaire was used to collect the
primary data from the respondents (experiences). Data were collected
from one hundred and eighty seven respondents residing in and
around the Emirates of Sharjah and Dubai of the United Arab
Emirates. The collected data was analyzed with the help of statistical
tools such as averages, percentages, factor analysis, Student’s t-test
and Structural Equation Modelling Technique.
Objectives of the study are to know the reasons how married and
unmarried or single consumers of products and services are
motivated to use blogs as a source of information, to know whether
the consumers of products and services irrespective of their marital
status share their views and experiences with other bloggers and to
know the respondents’ future intentions towards blogging.
The study revealed the following: Majority of the respondents
have the motivation to blog because they are willing to receive
comments on what they post about services, convenience of blogs to
search for information about services and products, by blogging
respondents share information on the symptoms of a disease/ disorder
that may be experienced by someone, helps to share information
about ready to cook mix products and are keen to spend more time
blogging in the future.
Abstract: Abundant and cheap agricultural waste of oil palm trunk (OPT) juice was used to produce bioethanol. Two strains of Saccharomyces cerevisiae and a strain of Pichia stipitis were used to produce bioethanol from the OPT juice. Fermentation was conducted at previously optimized condition at 30oC and without shaking. The kinetic parameters were estimated and calculated. Monod equation and Hinshelwood model is used to relate the specific growth to the concentration of the limiting substrate and also to simulate bioethanol production rate. Among the three strains, single S. cerevisiae Kyokai no. 7 produce the highest ethanol yield of 0.477 g/l.h within the shortest time (12 h). This yeast also produces more than 20 g/l ethanol concentration within 10 h of fermentation.
Abstract: Attractive and creative advertisement displays are
often in high demand as they are known to have profound impact on
the commercial market. In the fast advancement of technology,
advertising trend has taken a great leap in attracting more and more
demanding consumers. A low-cost and low-power consumption
flipping advertisement board has been developed in this paper. The
design of the electrical circuit and the controller of the advertisement
board are presented. A microcontroller, a Darlington Pair driver and a
unipolar stepper motor were used to operate the electrical flipping
advertisement board. The proposed system has been implemented
and the hardware has been tested to demonstrate the capability of
displaying multiple advertisements in a panel.
Abstract: Turbulent flow in complex geometries receives considerable attention due to its importance in many engineering applications. It has been the subject of interest for many researchers. Some of these interests include the design of storm water channels. The design of these channels requires testing through physical models. The main practical limitation of physical models is the so called “scale effect”, that is, the fact that in many cases only primary physical mechanisms can be correctly represented, while secondary mechanisms are often distorted. These observations form the basis of our study, which centered on problems associated with the design of storm water channels near the Dead Sea, in Israel. To help reach a final design decision we used different physical models. Our research showed good coincidence with the results of laboratory tests and theoretical calculations, and allowed us to study different effects of fluid flow in an open channel. We determined that problems of this nature cannot be solved only by means of theoretical calculation and computer simulation. This study demonstrates the use of physical models to help resolve very complicated problems of fluid flow through baffles and similar structures. The study applies these models and observations to different construction and multiphase water flows, among them, those that include sand and stone particles, a significant attempt to bring to the testing laboratory a closer association with reality.
Abstract: Al-Si-Mg-Ni(-Cu) alloys are widely used in the automotive industry. They have the advantage of low weight associated with low coefficient of thermal expansion and excellent mechanical properties – mainly at high temperatures. The corrosion resistance of these alloys in coastal area, particularly sea water, however is not yet known. In this investigation, electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization have been used to evaluate the corrosion resistance of Al-6Si-0.5Mg-2Ni (-2Cu) alloys in simulated sea water environments. The potentiodynamic polarization curves reveal that 2 wt% Cu content alloy (Alloy-2) is more prone to corrosion than the Cu free alloy (Alloy-1). But the EIS test results showed that corrosion resistance or charge transfer resistance (Rct) increases with the addition of Cu. Due to addition of Cu and thermal treatment, the magnitude of open circuit potential (OCP), corrosion potential (Ecorr) and pitting corrosion potential (Epit) of Al-6Si-0.5Mg-2Ni alloy in NaCl solution were shifted to the more noble direction.
Abstract: The use of low quality concrete has been identified as one of the main causes of the incessant collapse of buildings in Nigeria. Emphasis has been on the use of poor quality aggregates, poor workmanship and the use of lean concrete mix with low cement quantity as the reasons for the low quality of concrete used for building construction in Nigeria. Surveys conducted revealed that in the construction of most privately owned buildings where concrete trial mixes and concrete compressive strength quality assurance tests are not conducted, concretes used for building constructions are produced using the 1:2:4 mix ratio irrespective of the cement grade/strength class. In this paper, the possible role of the use of inappropriate cement grade/strength class as a cause of the incessant collapse of building in Nigeria is investigated. Investigation revealed that the compressive strengths of concrete cubes produced with Portland-limestone cement grade 32.5 using 1:2:4 and 1:1.5:3 mix ratios are less than the 25MPa and 30MPa cube strengths generally recommended for building superstructures and foundations respectively. Conversely, the compressive strengths of concrete cubes produced with Portland-limestone cement grade 42.5 using 1:2:4 and 1:1.5:3 mix ratios exceed the 25MPa and 30MPa generally recommended for building superstructures and foundations respectively. Thus, it can be concluded that the use of inappropriate cement grade (Portland-limestone cement grade 32.5), particularly for the construction of building foundations is a potential cause of the incessant collapse of buildings in Nigeria. It is recommended that the Standards Organisation of Nigeria should embark on creating awareness for Nigerians, particularly, the home owners and the roadside craftsmen that Portland-limestone cement grade 32.5 should not be used for the construction of building load-carrying members, particularly, building foundations in order to reduce the incessant incidence of collapsed building.
Abstract: The expanded Invasive Weed Optimization algorithm (exIWO) is an optimization metaheuristic modelled on the original IWO version created by the researchers from the University of Tehran. The authors of the present paper have extended the exIWO algorithm introducing a set of both deterministic and non-deterministic strategies of individuals’ selection. The goal of the project was to evaluate the exIWO by testing its usefulness for solving some test instances of the traveling salesman problem (TSP) taken from the TSPLIB collection which allows comparing the experimental results with optimal values.
Abstract: This paper presents the findings of an experimental investigation of important machining parameters for the horizontal boring tool modified to mouth with a horizontal lathe machine to bore an overlength workpiece. In order to verify a usability of a modified tool, design of experiment based on Taguchi method is performed. The parameters investigated are spindle speed, feed rate, depth of cut and length of workpiece. Taguchi L9 orthogonal array is selected for four factors three level parameters in order to minimize surface roughness (Ra and Rz) of S45C steel tubes. Signal to noise ratio analysis and analysis of variance (ANOVA) is performed to study an effect of said parameters and to optimize the machine setting for best surface finish. The controlled factors with most effect are depth of cut, spindle speed, length of workpiece, and feed rate in order. The confirmation test is performed to test the optimal setting obtained from Taguchi method and the result is satisfactory.
Abstract: An optimisation method using both global and local
optimisation is implemented to determine the flapping profile which
will produce the most lift for an experimental wing-actuation system.
The optimisation method is tested using a numerical quasi-steady
analysis. Results of an optimised flapping profile show a 20% increase
in lift generated as compared to flapping profiles obtained by high
speed cinematography of a Sympetrum frequens dragonfly. Initial
optimisation procedures showed 3166 objective function evaluations.
The global optimisation parameters - initial sample size and stage
one sample size, were altered to reduce the number of function
evaluations. Altering the stage one sample size had no significant
effect. It was found that reducing the initial sample size to 400
would allow a reduction in computational effort to approximately
1500 function evaluations without compromising the global solvers
ability to locate potential minima. To further reduce the optimisation
effort required, we increase the local solver’s convergence tolerance
criterion. An increase in the tolerance from 0.02N to 0.05N decreased
the number of function evaluations by another 20%. However, this
potentially reduces the maximum obtainable lift by up to 0.025N.