Abstract: In this paper, design of solid-state battery/supercapacitor emulator based on dc-dc boost converter is described.
The emulator mimics charging behavior of any storage device based
on a predefined behavior set by the user. The device is operated by a
two-level control structure: high-level emulating controller and low-
level input voltage controller. Simulation and experimental results are
shown to demonstrate the emulator operation.
Abstract: In order to verify the performance of lunar lander
structure, landing-impact test is urgently needed. And the test
equipment is necessary for the test. The functions and the key points of
the equipment are presented to satisfy the requirements of the test, and
the design scheme is proposed. The composition, the major function
and the critical parts’ design of the equipment are introduced. By the
load test of releasing device and single-beam hoist, and the
compatibility test of landing-impact testing system, the rationality and
reliability of the equipment is proved.
Abstract: The main aim of this research was to investigate the
perspectives of English language teachers and learners on the effect
of test techniques on reading comprehension, test performance and
assessment. The research has also aimed at finding the differences
between teacher and learner perspectives, specifying the test
techniques which have the highest effect, investigating the other
factors affecting reading comprehension, and comparing the results
with the similar studies. In order to achieve these objectives,
perspectives and findings of different researchers were reviewed, two
different questionnaires were prepared to collect data for the
perspectives of teachers and learners, the questionnaires were applied
to 26 learners and 8 teachers from the University of Batna (Algeria),
and quantitative and qualitative data analysis of the results were
done. The results and analysis of the results show that different test
techniques affect reading comprehension, test performance and
assessment at different percentages rates.
Abstract: This paper is concerning the issues of behaviour of
lightweight expanded clay aggregates concrete exposed to high
temperature. Lightweight aggregates from expanded clay are
produced by firing of row material up to temperature 1050°C.
Lightweight aggregates have suitable properties in terms of volume
stability, when exposed to temperatures up to 1050°C, which could
indicate their suitability for construction applications with higher risk
of fire. The test samples were exposed to heat by using the standard
temperature-time curve ISO 834. Negative changes in resulting
mechanical properties, such as compressive strength, tensile strength,
and flexural strength were evaluated. Also visual evaluation of the
specimen was performed. On specimen exposed to excessive heat, an
explosive spalling could be observed, due to evaporation of
considerable amount of unbounded water from the inner structure of
the concrete.
Abstract: This study aimed at investigating whether the
functional brain networks constructed using the initial EEG (obtained
when patients first visited hospital) can be correlated with the
progression of cognitive decline calculated as the changes of
mini-mental state examination (MMSE) scores between the latest and
initial examinations. We integrated the time–frequency cross mutual
information (TFCMI) method to estimate the EEG functional
connectivity between cortical regions, and the network analysis based
on graph theory to investigate the organization of functional networks
in aMCI. Our finding suggested that higher integrated functional
network with sufficient connection strengths, dense connection
between local regions, and high network efficiency in processing
information at the initial stage may result in a better prognosis of the
subsequent cognitive functions for aMCI. In conclusion, the functional
connectivity can be a useful biomarker to assist in prediction of
cognitive declines in aMCI.
Abstract: Brain functional networks based on resting-state EEG
data were compared between patients with mild Alzheimer’s disease
(mAD) and matched patients with amnestic subtype of mild cognitive
impairment (aMCI). We integrated the time–frequency cross mutual
information (TFCMI) method to estimate the EEG functional
connectivity between cortical regions and the network analysis based
on graph theory to further investigate the alterations of functional
networks in mAD compared with aMCI group. We aimed at
investigating the changes of network integrity, local clustering,
information processing efficiency, and fault tolerance in mAD brain
networks for different frequency bands based on several topological
properties, including degree, strength, clustering coefficient, shortest
path length, and efficiency. Results showed that the disruptions of
network integrity and reductions of network efficiency in mAD
characterized by lower degree, decreased clustering coefficient, higher
shortest path length, and reduced global and local efficiencies in the
delta, theta, beta2, and gamma bands were evident. The significant
changes in network organization can be used in assisting
discrimination of mAD from aMCI in clinical.
Abstract: Spectrum sensing is the main feature of cognitive
radio technology. Spectrum sensing gives an idea of detecting the
presence of the primary users in a licensed spectrum. In this paper we
compare the theoretical results of detection probability of different
fading environments like Rayleigh, Rician, Nakagami-m fading
channels with the simulation results using energy detection based
spectrum sensing. The numerical results are plotted as Pf Vs Pd for
different SNR values, fading parameters. It is observed that
Nakagami fading channel performance is better than other fading
channels by using energy detection in spectrum sensing. A MATLAB
simulation test bench has been implemented to know the performance
of energy detection in different fading channel environment.
Abstract: This article presents a new vibration diagnostic
method designed to (PM) machines with permanent magnets. Those
devices are commonly used in small wind and water systems or
vehicles drives. The author’s method is very innovative and unique.
Specific structural properties of PM machines are used in this method
- electromotive force (EMF) generated due to vibrations. There was
analysed number of publications which describe vibration diagnostic
methods and tests of electrical PM machines and there was no
method found to determine the technical condition of such machine
basing on their own signals. In this article will be discussed: the
method genesis, the similarity of machines with permanent magnet to
vibration sensor and simulation and laboratory tests results. The
method of determination the technical condition of electrical machine
with permanent magnets basing on its own signals is the subject of
patent application and it is the main thesis of author’s doctoral
dissertation.
Abstract: Novel bio-based polymer electrolyte was synthesized
with LiClO4 as the main source of charge carrier. Initially,
polyurethane-LiClO4 polymer electrolytes were synthesized via
prepolymerization method with different NCO/OH ratios and labelled
them as PU1, PU2, PU3 and PU4. Fourier transform infrared (FTIR)
analysis indicates the co-ordination between Li+ ion and polyurethane
in PU1. Differential scanning calorimetry (DSC) analysis indicates
PU1 has the highest glass transition temperature (Tg) corresponds to
the most abundant urethane group which is the hard segment in PU1.
Scanning electron microscopy (SEM) shows the good miscibility
between lithium salt and the polymer. The study found that PU1
possessed the greatest ionic conductivity and the lowest activation
energy, Ea. All the polyurethanes exhibited linear Arrhenius
variations indicating ion transport via simple lithium ion hopping in
polyurethane. This research proves the NCO content in polyurethane
plays an important role in affecting the ionic conductivity of this
polymer electrolyte.
Abstract: Information and Communication Technologies (ICTs)
are pervasive nowadays, including in education where they are
expected to improve the performance of learners. However, the hope
placed in ICTs to find viable solutions to the problem of poor
academic performance in schools in the developing world has not yet
yielded the expected benefits. This problem serves as a motivation to
this study whose aim is to examine the perceptions of educators on
the advantages and disadvantages of e-learning. This aim will be
subdivided into two types of research objectives. Objectives on the
identification and design of theories and models will be achieved
using content analysis and literature review. However, the objective
on the empirical testing of such theories and models will be achieved
through the survey of educators from different schools in the
Pinetown District of the South African Kwazulu-Natal province.
SPSS is used to quantitatively analyse the data collected by the
questionnaire of this survey using descriptive statistics and Pearson
correlations after assessing the validity and the reliability of the data.
The main hypothesis driving this study is that there is a relationship
between the demographics of educators’ and their adherence to
learning theories on one side, and their perceptions on the advantages
and disadvantages of e-learning on the other side, as argued by
existing research; but this research views these learning theories
under three perspectives: educators’ adherence to self-regulated
learning, to constructivism, and to progressivism. This hypothesis
was fully confirmed by the empirical study except for the
demographic factor where teachers’ level of education was found to
be the only demographic factor affecting the perceptions of educators
on the advantages and disadvantages of e-learning.
Abstract: The paper deals with current issues in research of
advanced methods to increase reliability of traditional timber
structural elements. It analyses the issue of strengthening of bent
timber beams, such as ceiling beams in old (historical) buildings with
additional concrete slab in combination with externally bonded fibre -
reinforced polymer. The paper describes experimental testing of
composite timber-concrete beam with FRP reinforcement and
compares results with FEM analysis.
Abstract: The effect of particle size on shear strength of
granular materials are investigated using direct shear tests. Small
direct shear test (60 mm by 60 mm by 24 mm deep) were conducted
for particles passing the sieves with opening size of 2.36 mm.
Meanwhile, particles passing the standard 20 mm sieves were tested
using large direct shear test (300 mm by 300 mm by 200 mm deep).
The large direct shear tests and the small direct shear tests carried out
using the same shearing rate of 0.09 mm/min and similar normal
stresses of 100, 200 and 300 kPa. The results show that the peak and
residual shear strength increases as particle size increases.
Abstract: The objective of the study was to select the survival of
probiotic strains when exposed to acidic and bile salts condition. Four
probiotic strains Lactobacillus casei subsp. rhamnosus TISTR 047,
Lactobacillus casei TISTR 1500, Lactobacillus acidophilus TISTR
1338 and Lactobacillus plantarum TISTR 1465 were cultured in
MRS broth and incubated at 35ºC for 15 hours before being inoculated
into acidic condition 5 M HCl, pH 2 for 2 hours and bile salt 0.3%,
pH 5.8 for 8 hour. The survived probiotics were counted in MRS agar.
Among four stains, Lactobacillus casei subsp. rhamnosus TISTR 047
was the highest tolerance specie. Lactobacillus casei subsp.
rhamnosus TISTR 047 reduced 6.74±0.07 log CFU/ml after growing
in acid and 5.52±0.05 log CFU/ml after growing in bile salt. Then,
double emulsion of microorganisms was chosen to encapsulate before
spray drying. Spray drying was done with the inlet temperature 170ºC
and outlet temperature 80ºC. The results showed that the survival of
encapsulated Lactobacillus casei subsp. rhamnosus TISTR 047 after
spray drying decreased from 9.63 ± 0.32 to 8.31 ± 0.11 log CFU/ml
comparing with non-encapsulated, 9.63 ± 0.32 to 4.06 ± 0.08 log
CFU/ml. Therefore, Lactobacillus casei subsp. rhamnosus TISTR 047
would be able to survive in gastrointestinal and spray drying condition.
Abstract: This paper attempts to evaluate the effect of fire
damage on concrete by using nonlinear resonance vibration method,
one of the nonlinear nondestructive method. Concrete exhibits not
only nonlinear stress-strain relation but also hysteresis and discrete
memory effect which are contained in consolidated materials.
Hysteretic materials typically show the linear resonance frequency
shift. Also, the shift of resonance frequency is changed according to
the degree of micro damage. The degree of the shift can be obtained
through nonlinear resonance vibration method. Five exposure
scenarios were considered in order to make different internal micro
damage. Also, the effect of post-fire-curing on fire-damaged concrete
was taken into account to conform the change in internal damage.
Hysteretic nonlinearity parameter was obtained by amplitudedependent
resonance frequency shift after specific curing periods. In
addition, splitting tensile strength was measured on each sample to
characterize the variation of residual strength. Then, a correlation
between the hysteretic nonlinearity parameter and residual strength
was proposed from each test result.
Abstract: Well-designed composite steel and concrete structures
highlight the good material properties and lower the deficiencies of
steel and concrete, in particular they make use of high tensile strength
of steel and high stiffness of concrete. The most common composite
steel and concrete structure is a simply supported beam, which
concrete slab transferring the slab load to a beam is connected to the
steel cross-section. The aim of this paper is to find the most adequate
numerical model of a simply supported composite beam with the
cross-sectional and material parameters based on the results of a
processed parametric study and numerical analysis. The paper also
evaluates the suitability of using compact concrete with the
lightweight aggregates for composite steel and concrete beams. The
most adequate numerical model will be used in the resent future to
compare the results of laboratory tests.
Abstract: The purpose of this research was to identify factors
that influenced the success of e-commerce implementation within
SMEs businesses. In order to achieve the objectives of this research,
the researcher collected data from random firms in Thailand, both the
users and those who are not using the e-commerce. The data was
comprised of the results of 310 questionnaires, as well as 10
interviews with owner/managers of businesses who are currently
using e-commerce successfully. The data were analyzed by using
descriptive statistics, which included frequency, percentages, mean,
and the standard deviation of pertinent factors. Independent t-test and
one-way ANOVA test were also used. The findings of this research
revealed that 50% of all the firms surveyed had e-commerce website,
whereas, over 20% of all firms surveyed had developing an ecommerce
strategy. The result findings also indicate that
organizational factors, technological factors and environment factors
as significant factors effecting success of e-commerce
implementation in SMEs. From the hypotheses testing, the findings
revealed that the different level of support use ecommerce by
owner/manager had different success in e-commerce implementation.
Moreover, the difference in e-commerce management approach
affected the success in terms of higher total sales for the business or
higher number of retained or returning customers.
Abstract: The success of any retail business is predisposed by its
swift response and its knack in understanding the constraints and the
requirements of customers. In this paper a conceptual design model
of an automated customer-friendly supermarket has been proposed.
In this model a 10-sided, space benefited, regular polygon shaped
gravity shelves have been designed for goods storage and effective
customer-specific algorithms have been built-in for quick automatic
delivery of the randomly listed goods. The algorithm is developed
with two main objectives, viz., delivery time and priority. For
meeting these objectives the randomly listed items are reorganized
according to the critical-path of the robotic arm specific to the
identified shop and its layout and the items are categorized according
to the demand, shape, size, similarity and nature of the product for an
efficient pick-up, packing and delivery process. We conjectured that
the proposed automated supermarket model reduces business
operating costs with much customer satisfaction warranting a winwin
situation.
Abstract: Copper being one of the major intrinsic residual
impurities in steel possesses the tendency to induce severe
microstructural distortions if not controlled within certain limits.
Hence, this paper investigates the effect of this element on the
mechanical properties of construction steel with a view to ascertain
its safe limits for effective control. The experiment entails collection
of statistically scheduled samples of hot rolled profiles with varied
copper concentrations in the range of 0.12-0.39 wt. %. From these
samples were prepared standard test specimens subjected to tensile,
impact, hardness and microstructural analyses. Results show a rather
huge compromise in mechanical properties as the specimens
demonstrated 54.3%, 74.2% and 64.9% reduction in tensile strength,
impact energy and hardness respectively as copper content increases
from 0.12 wt. % to 0.39 wt. %. The steel’s abysmal performance is
due to the severe distortion of the microstructure occasioned by the
development of incoherent complex compounds which weaken the
pearlite reinforcing phase. It is concluded that the presence of copper
above 0.22 wt. % is deleterious to construction steel performance.
Abstract: Mass flow measurement is the basis of most technoeconomic
formulations in the chemical industry. This calls for
reliable and accurate detection of mass flow. Flow measurement
laboratory experiments were conducted using various instruments.
These consisted of orifice plates, various sized rotameters, wet gas
meter and soap bubble meter. This work was aimed at evaluating
appropriate operating conditions and accuracy of the aforementioned
devices. The experimental data collected were compared to
theoretical predictions from Bernoulli’s equation and calibration
curves supplied by the instrument’s manufacturers. The results
obtained showed that rotameters were more reliable for measuring
high and low flow rates; while soap-bubble meters and wet-gas
meters were found to be suitable for measuring low flow rates. The
laboratory procedures and findings of the actual work can assist
engineering students and professionals in conducting their flow
measurement laboratory test work.
Abstract: The study deals with the challenges in developing a
test rig to test the performance of water lubricated journal bearing.
The test rig is designed to simulate the working conditions of the
bearing in order to understand their performance before they are put
in operation. The bearing that is studied is the commercially available
water lubricated bearing which has a rubber liner bonded with a rigid
metal shell. The lubricant enters the bearing axially through a
pressurized inlet tank and exits to an outlet tank which is at
sufficiently low pressure. The load on the bearing is applied through
the dead weight system which acts both in upward and downward
direction so that net load acts on the bearing. The issues in feeding
the lubricant into the bearing from the inlet side and preventing the
leakage of the lubricant is discussed. The application of the load on
the test bearing while maintaining the bearing afloat is also discussed.