Abstract: This paper presents the design and analysis of a parallel
connected inverter configuration of. The configuration consists of
parallel connected three-phase dc/ac inverter. Series resistors added
to the inverter output to maintain same current in each inverter of the
two parallel inverters, and to reduce the circulating current in the
parallel inverters to the minimum. High frequency third harmonic
injection PWM (THIPWM) employed to reduce the total harmonic
distortion and to make maximum use of the voltage source. DSP was
used to generate the THIPWM and the control algorithm for the
converter. Selected experimental results have been shown to validate
the proposed system.
Abstract: In this study, control performance of a smart base
isolation system consisting of a friction pendulum system (FPS) and a
magnetorheological (MR) damper has been investigated. A fuzzy
logic controller (FLC) is used to modulate the MR damper so as to
minimize structural acceleration while maintaining acceptable base
displacement levels. To this end, a multi-objective optimization
scheme is used to optimize parameters of membership functions and
find appropriate fuzzy rules. To demonstrate effectiveness of the
proposed multi-objective genetic algorithm for FLC, a numerical
study of a smart base isolation system is conducted using several
historical earthquakes. It is shown that the proposed method can find
optimal fuzzy rules and that the optimized FLC outperforms not only a
passive control strategy but also a human-designed FLC and a
conventional semi-active control algorithm.
Abstract: Network on Chip (NoC) has emerged as a promising
on chip communication infrastructure. Three Dimensional Integrate
Circuit (3D IC) provides small interconnection length between layers
and the interconnect scalability in the third dimension, which can
further improve the performance of NoC. Therefore, in this paper,
a hierarchical cluster-based interconnect architecture is merged with
the 3D IC. This interconnect architecture significantly reduces the
number of long wires. Since this architecture only has approximately
a quarter of routers in 3D mesh-based architecture, the average
number of hops is smaller, which leads to lower latency and higher
throughput. Moreover, smaller number of routers decreases the area
overhead. Meanwhile, some dual links are inserted into the bottlenecks
of communication to improve the performance of NoC.
Simulation results demonstrate our theoretical analysis and show the
advantages of our proposed architecture in latency, throughput and
area, when compared with 3D mesh-based architecture.
Abstract: Coordinated supply chain represents major challenges
for the different actors involved in it, because each agent responds to
individual interests. The paper presents a framework with the
reviewed literature regarding the system's decision structure and
nature of demand. Later, it characterizes an agri food supply chain in
the Central Region of Colombia, it responds to a decentralized
distribution system and a stochastic demand. Finally, the paper
recommends coordinating the chain based on shared information, and
mechanisms for each agent, as VMI (vendor-managed inventory)
strategy for farmer-buyer relationship, information system for
farmers and contracts for transportation service providers.
Abstract: Based on the fuzzy set theory this work develops two
adaptations of iterative methods that solve mathematical programming
problems with uncertainties in the objective function and in
the set of constraints. The first one uses the approach proposed by
Zimmermann to fuzzy linear programming problems as a basis and
the second one obtains cut levels and later maximizes the membership
function of fuzzy decision making using the bound search method.
We outline similarities between the two iterative methods studied.
Selected examples from the literature are presented to validate the
efficiency of the methods addressed.
Abstract: In many applications, data is in graph structure, which
can be naturally represented as graph-structured XML. Existing
queries defined on tree-structured and graph-structured XML data
mainly focus on subgraph matching, which can not cover all the
requirements of querying on graph. In this paper, a new kind of
queries, topological query on graph-structured XML is presented.
This kind of queries consider not only the structure of subgraph but
also the topological relationship between subgraphs. With existing
subgraph query processing algorithms, efficient algorithms for topological
query processing are designed. Experimental results show the
efficiency of implementation algorithms.
Abstract: Policies that support entrepreneurship are keys to the
generation of new business. In Brazil, seed capital, installation of
technology parks, programs and zero interest financing, economic
subsidy as Program First Innovative Company (PRIME) are
examples of incentive policies. For the implementation of PRIME, in
particular the Brazilian Innovation Agency (FINEP) decentralized
operationalization so that business incubators could select innovative
projects. This paper analyzes the program PRIME Business Incubator
Center of the State of Sergipe (CISE) after calculating the mean and
standard deviation of the grades obtained by companies in the factors
of innovation, market potential, financial return economic, market
strategy and staff and application of the Mann-Whitney test.
Abstract: Innovations in technology have created new ethical
challenges. Essential use of electronic communication in the
workplace has escalated at an astronomical rate over the past decade.
As such, legal and ethical dilemmas confronted by both the employer
and the employee concerning managerial control and ownership of einformation
have increased dramatically in the USA. From the
employer-s perspective, ownership and control of all information
created for the workplace is an undeniable source of economic
advantage and must be monitored zealously. From the perspective of
the employee, individual rights, such as privacy, freedom of speech,
and freedom from unreasonable search and seizure, continue to be
stalwart legal guarantees that employers are not legally or ethically
entitled to abridge in the workplace. These issues have been the
source of great debate and the catalyst for legal reform. The fine line
between ethical and legal has been complicated by emerging
technologies. This manuscript will identify and discuss a number of
specific legal and ethical issues raised by the dynamic electronic
workplace and conclude with suggestions that employers should
follow to respect the delicate balance between employees- legal
rights to privacy and the employer's right to protect its knowledge
systems and infrastructure.
Abstract: The intention of this study to design the probability optimized sewing sack-s workstation based on ergonomics for productivity improvement and decreasing musculoskeletal disorders. The physical dimensions of two workers were using to design the new workstation. The physical dimensions are (1) sitting height, (2) mid shoulder height sitting, (3) shoulder breadth, (4) knee height, (5) popliteal height, (6) hip breadth and (7) buttock-knee length. The 5th percentile of buttock knee length sitting (51 cm), the 50th percentile of mid shoulder height sitting (62 cm) and the 95th percentile of popliteal height (43 cm) and hip breadth (45 cm) applied to design the workstation for sewing sack-s operator and the others used to adjust the components of this workstation. The risk assessment by RULA before and after using the probability optimized workstation were 7 and 7 scores and REBA scores were 11 and 5, respectively. Body discomfort-abnormal index was used to assess muscle fatigue of operators before adjustment workstation found that neck muscles, arm muscles area, muscles on the back and the lower back muscles fatigue. Therefore, the extension and flexion exercise was applied to relief musculoskeletal stresses. The workers exercised 15 minutes before the beginning and the end of work for 5 days. After that, the capability of flexion and extension muscles- workers were increasing in 3 muscles (arm, leg, and back muscles).
Abstract: The demand for higher performance graphics
continues to grow because of the incessant desire towards realism.
And, rapid advances in fabrication technology have enabled us to
build several processor cores on a single die. Hence, it is important to
develop single chip parallel architectures for such data-intensive
applications. In this paper, we propose an efficient PIM architectures
tailored for computer graphics which requires a large number of
memory accesses. We then address the two important tasks necessary
for maximally exploiting the parallelism provided by the architecture,
namely, partitioning and placement of graphic data, which affect
respectively load balances and communication costs. Under the
constraints of uniform partitioning, we develop approaches for optimal
partitioning and placement, which significantly reduce search space.
We also present heuristics for identifying near-optimal placement,
since the search space for placement is impractically large despite our
optimization. We then demonstrate the effectiveness of our partitioning
and placement approaches via analysis of example scenes; simulation
results show considerable search space reductions, and our heuristics
for placement performs close to optimal – the average ratio of
communication overheads between our heuristics and the optimal was
1.05. Our uniform partitioning showed average load-balance ratio of
1.47 for geometry processing and 1.44 for rasterization, which is
reasonable.
Abstract: Fire disaster is the major factor to endanger the public
and environmental safety. People lost their life during fire disaster
mainly be attributed to the dense smoke and toxic gas under
combustion, which hinder the escape of people and the rescue of
firefighters under fire disaster. The smoke suppression effect of
several transitional metals oxide on the epoxy resin treated with
intumescent flame retardant and titanate couple agent
(EP/IFR/Titanate) system have been investigated. The results showed
manganese dioxide has great effect on reducing the smoke density rate
(SDR) of EP/IFR/Titanate system; however it has little effect to reduce
the maximum smoke density (MSD) of EP/IFR/Titanate system.
Copper oxide can decrease the maximum smoke density (MSD) and
smoke density rate of EP/IFR/Titanate system substantially. The MSD
and SDR of EP/IFR/Titanate system can reduce 20.3% and 39.1%
respectively when 2% of copper oxide is introduced.
Abstract: Only recently have water ethics received focused interest in the international water community. Because water is metabolically basic to life, an ethical dimension persists in every decision related to water. Water ethics at once express human society-s approach to water and act as guidelines for behaviour. Ideas around water are often implicit and embedded as assumptions. They can be entrenched in behaviour and difficult to contest because they are difficult to “see". By explicitly revealing the ethical ideas underlying water-related decisions, human society-s relationship with water, and with natural systems of which water is part, can be contested and shifted or be accepted with conscious intention by human society. In recent decades, improved understanding of water-s importance for ecosystem functioning and ecological services for human survival is moving us beyond this growth-driven, supplyfocused management paradigm. Environmental ethics challenge this paradigm by extending the ethical sphere to the environment and thus water or water Resources management per se. An ethical approach is a legitimate, important, and often ignored approach to effect change in environmental decision making. This qualitative research explores principles of water ethics and examines the underlying ethical precepts of selected water policy examples. The constructed water ethic principles act as a set of criteria against which a policy comparison can be established. This study shows that water Resources management is a progressive issue by embracing full public participation and a new planning model, and knowledgegeneration initiatives.
Abstract: The purpose of this article is to analyze the
degree of concentration in the banking market in EU member
states as well as to determine the impact of the length of EU
membership on the degree of concentration. In that sense
several analysis were conducted, specifically, panel analysis,
calculation of correlation coefficient and regression analysis of
the impact of the length of EU membership on the degree of
concentration. Panel analysis was conducted to determine
whether there is a similar trend of concentration in three
groups of countries - countries with a low, moderate and high
level of concentration. The conducted panel analysis showed
that in EU countries with a moderate level of concentration,
the level of concentration decreases. The calculation of
correlation showed that, to some extent, with other influential
factors, the length of EU membership negatively affects the
market concentration of the banking market. Using the
regression analysis for investigation of the influence of the
length of EU membership on the level of concentration in the
banking sector in a particular country, the results reveal that
there is a negative effect of the length in EU membership on
market concentration, although it is not significantly influential
variable.
Abstract: Most of the existing text mining approaches are
proposed, keeping in mind, transaction databases model. Thus, the
mined dataset is structured using just one concept: the “transaction",
whereas the whole dataset is modeled using the “set" abstract type. In
such cases, the structure of the whole dataset and the relationships
among the transactions themselves are not modeled and
consequently, not considered in the mining process.
We believe that taking into account structure properties of
hierarchically structured information (e.g. textual document, etc ...)
in the mining process, can leads to best results. For this purpose, an
hierarchical associations rule mining approach for textual documents
is proposed in this paper and the classical set-oriented mining
approach is reconsidered profits to a Direct Acyclic Graph (DAG)
oriented approach. Natural languages processing techniques are used
in order to obtain the DAG structure. Based on this graph model, an
hierarchical bottom up algorithm is proposed. The main idea is that
each node is mined with its parent node.
Abstract: Frequent patterns are patterns such as sets of features or items that appear in data frequently. Finding such frequent patterns has become an important data mining task because it reveals associations, correlations, and many other interesting relationships hidden in a dataset. Most of the proposed frequent pattern mining algorithms have been implemented with imperative programming languages such as C, Cµ, Java. The imperative paradigm is significantly inefficient when itemset is large and the frequent pattern is long. We suggest a high-level declarative style of programming using a functional language. Our supposition is that the problem of frequent pattern discovery can be efficiently and concisely implemented via a functional paradigm since pattern matching is a fundamental feature supported by most functional languages. Our frequent pattern mining implementation using the Haskell language confirms our hypothesis about conciseness of the program. The performance studies on speed and memory usage support our intuition on efficiency of functional language.
Abstract: School homework has been synonymous with students- life in Chinese national type primary schools in Malaysia. Although many reports in the press claimed that students were burdened with too much of it, homework continues to be a common practice in national type schools that is believed to contribute to academic achievement. This study is conducted to identify the relationship between the burden of school homework and academic achievement among pupils in Chinese National Type Primary School in the state of Perak, Malaysia. A total of 284 students (142 from urban and 142 from rural) respectively were chosen as participants in this study. Variables of gender and location (urban/rural areas) has shown significant difference in student academic achievement. Female Chinese student from rural areas showed a higher mean score than males from urban area. Therefore, the Chinese language teachers should give appropriate and relevant homework to primary school students to achieve good academic performance.
Abstract: The Norwegian Military Academy (Army) has
initiated a project with the main ambition to explore possible avenues
to enhancing operational effectiveness through an increased use of
simulation-based training and exercises. Within a cost/benefit
framework, we discuss opportunities and limitations of vertical and
horizontal integration of the existing tactical training system. Vertical
integration implies expanding the existing training system to span the
full range of training from tactical level (platoon, company) to
command and staff level (battalion, brigade). Horizontal integration
means including other domains than army tactics and staff
procedures in the training, such as military ethics, foreign languages,
leadership and decision making. We discuss each of the integration
options with respect to purpose and content of training, "best
practice" for organising and conducting simulation-based training,
and suggest how to evaluate training procedures and measure
learning outcomes. We conclude by giving guidelines towards further
explorative work and possible implementation.
Abstract: Our Medicine-oriented research is based on a medical
data set of real patients. It is a security problem to share
patient private data with peoples other than clinician or hospital
staff. We have to remove person identification information
from medical data. The medical data without private data
are available after a de-identification process for any research
purposes. In this paper, we introduce an universal automatic
rule-based de-identification application to do all this stuff on an
heterogeneous medical data. A patient private identification is
replaced by an unique identification number, even in burnedin
annotation in pixel data. The identical identification is used
for all patient medical data, so it keeps relationships in a data.
Hospital can take an advantage of a research feedback based
on results.
Abstract: Current mode circuits like current conveyors are
getting significant attention in current analog ICs design due to their
higher band-width, greater linearity, larger dynamic range, simpler
circuitry, lower power consumption and less chip area. The second
generation current controlled conveyor (CCCII) has the advantage of
electronic adjustability over the CCII i.e. in CCCII; adjustment of the
X-terminal intrinsic resistance via a bias current is possible. The
presented approach is based on the CMOS implementation of second
generation positive (CCCII+), negative (CCCII-) and dual Output
Current Controlled Conveyor (DOCCCII) and its application as
Universal filter. All the circuits have been designed and simulated
using 65nm CMOS technology model parameters on Cadence
Virtuoso / Spectre using 1V supply voltage. Various simulations have
been carried out to verify the linearity between output and input
ports, range of operation frequency, etc. The outcomes show good
agreement between expected and experimental results.
Abstract: A device analysis of the photoconductive
semiconductor switch is carried out to investigate distribution of
electric field and carrier concentrations as well as the current density
distribution. The operation of this device was then investigated as a
switch operating in X band. It is shown that despite the presence of
symmetry geometry, switch current density of the on-state steady
state mode is distributed asymmetrically throughout the device.