Abstract: Measurements of capacitance C and dissipation
factor tand of the stator insulation system provide useful information
about internal defects within the insulation. The index k is defined as
the proportionality constant between the changes at high voltage of
capacitance DC and of the dissipation factor Dtand . DC and
Dtand values were highly correlated when small flat defects were
within the insulation and that correlation was lost in the presence of
large narrow defects like electrical treeing. The discrimination
between small and large defects is made resorting to partial discharge
PD phase angle analysis. For the validation of the results, C and tand
measurements were carried out in a 15MVA 4160V steam turbine
turbogenerator placed in a sugar mill. In addition, laboratory test
results obtained by other authors were analyzed jointly. In such
laboratory tests, model coil bars subjected to thermal cycling resulted
highly degraded and DC and Dtand values were not correlated. Thus,
the index k could not be calculated.
Abstract: Finding the shortest path between two positions is a
fundamental problem in transportation, routing, and communications
applications. In robot motion planning, the robot should pass around
the obstacles touching none of them, i.e. the goal is to find a
collision-free path from a starting to a target position. This task has
many specific formulations depending on the shape of obstacles,
allowable directions of movements, knowledge of the scene, etc.
Research of path planning has yielded many fundamentally different
approaches to its solution, mainly based on various decomposition
and roadmap methods. In this paper, we show a possible use of
visibility graphs in point-to-point motion planning in the Euclidean
plane and an alternative approach using Voronoi diagrams that
decreases the probability of collisions with obstacles. The second
application area, investigated here, is focused on problems of finding
minimal networks connecting a set of given points in the plane using
either only straight connections between pairs of points (minimum
spanning tree) or allowing the addition of auxiliary points to the set
to obtain shorter spanning networks (minimum Steiner tree).
Abstract: The aim of this study was to extract sugar from
sugarcane using high electric field pulse (HELP) as a non-thermal cell permeabilization method. The result of this study showed that it
is possible to permeablize sugar cane cells using HELP at very short times (less than 10 sec.) and at room temperature. Increasing the field strength (from 0.5kV/cm to 2kV/cm) and pulse number (1 to 12) led to increasing the permeabilization of sugar cane cells. The energy
consumption during HELP treatment of sugar cane (2.4 kJ/kg) was about 100 times less compared to thermal cell disintegration at 85
Abstract: Asthma is a condition that causing chronic health problems in children. In addition to basic therapy against disease, we must try to reduce the impact of chronic health problems and also optimize their medical aspect of growth and development. A boy with mild asthma attack frequent episode did not showed any improvement with medical treatment and his asthma control test was 11. From radiologic examination he got hyperaerated lung and billateral sinusitis maxillaris; skin test results were house dust, food and pet allergy; an overweight body; bad school grades; psychological and environmental problem. We followed and evaluated this boy in 6 months, treated holistically. Even we could not do much on environmental but no more psychological and school problems, his on a good bodyweight and his asthma control test was 22. A case of a child with mild asthma attack frequent episode was reported. Asthma clinical course show no significant improvement when other predisposing factor is not well-controlled and a child’s growth and development may be affected. Improving condition of the patient can be created with the help of loving and caring way of nurturing from the parents and supportive peer group. Therefore, continuous and consistent monitoring is required because prognosis of asthma is generally good when regularly and properly controlled.
Abstract: Twenty four New Zealand white rabbits (12 does and
12 bucks) and twenty four Flanders (12 does and 12 bucks) rabbits,
allotted into two feeding regime (6 for each breed, 3 males and 3
females) first one fed commercial ration and second one fed
commercial diet plus sodium butyrate (300 g/ton). The obtained
results showed that at end of 8th week experimental period New
Zealand white rabbits were heavier body weight than Flanders rabbits
(1934.55+39.05 vs. 1802.5+30.99 g); significantly high body weight
gain during experimental period especially during 8th week
(136.1+3.5 vs. 126.8+1.8 g/week); better feed conversion ratio during
all weeks of experiment from first week (3.07+0.16 vs. 3.12+0.10)
till the 8th week of experiment (5.54+0.16 vs. 5.76+0.07) with
significantly high dressing percentages (0.54+0.01 vs. 0.52+0.01).
Also all carcass cuts were significantly high in New Zealand white
rabbits than Flanders. Females rabbits (at the same age) were lower
body weight than males from start of experiment (941.1+39.8
vs.972.1+33.5 g) till the end of experiment (1833.64+37.69 vs.
1903.41+36.93 g); gained less during all weeks of experiment except
during 8th week (132.1+2.3 vs. 130.9+3.4 g/week), with lower
dressing percentage (0.52+0.01 vs. 0.53+0.01) and lighter carcass
cuts than males, however, they had better feed conversion ratio
during 1st week, 7th week and 8th week of experiment. Addition of
300g sodium butyrate/ton of rabbit increased the body weight of
rabbits at the end of experimental period (1882.71+26.45 vs.
1851.5+49.82 g); improve body weight gain at 3rd, 4th, 5th, 6th and
7th week of experiment and significantly improve feed conversion
ratio during all weeks of the experiment from 1st week (2.85+0.07
vs. 3.30+0.15) till the 8th week of the experiment (5.51+0.12 vs.
5.77+0.12). Also the dressing percentage was higher in Sodium
butyrate fed groups than control one (0.53+0.01 vs. 0.52+0.01) and
the most important results of feeding sodium butyrate is the reducing
of the mortality percentage in rabbits during 8 week experiment to
zero percentage as compared with 16% in control group.
Abstract: Dilated cardiomyopathy (DCM) is a severe
cardiovascular disorder characterized by progressive systolic
dysfunction due to cardiac chamber dilatation and inefficient
myocardial contractility often leading to chronic heart failure.
Recently, a genome-wide association studies (GWASs) on DCM
indicate that the ZBTB17 gene rs10927875 single nucleotide
polymorphism is associated with DCM. The aim of the study was to
identify the distribution of ZBTB17 gene rs10927875 polymorphism
in 50 Slovak patients with DCM and 80 healthy control subjects
using the Custom Taqman®SNP Genotyping assays. Risk factors
detected at baseline in each group included age, sex, body mass
index, smoking status, diabetes and blood pressure. The mean age of
patients with DCM was 52.9±6.3 years; the mean age of individuals
in control group was 50.3±8.9 years. The distribution of investigated
genotypes of rs10927875 polymorphism within ZBTB17 gene in the
cohort of Slovak patients with DCM was as follows: CC (38.8%), CT
(55.1%), TT (6.1%), in controls: CC (43.8%), CT (51.2%), TT
(5.0%). The risk allele T was more common among the patients with
dilated cardiomyopathy than in normal controls (33.7% versus
30.6%). The differences in genotype or allele frequencies of ZBTB17
gene rs10927875 polymorphism were not statistically significant
(p=0.6908; p=0.6098). The results of this study suggest that ZBTB17
gene rs10927875 polymorphism may be a risk factor for
susceptibility to DCM in Slovak patients with DCM. Studies of
numerous files and additional functional investigations are needed to
fully understand the roles of genetic associations.
Abstract: Non-uniform current distribution in polymer
electrolyte membrane fuel cells results in local over-heating,
accelerated ageing, and lower power output than expected. This
issue is very critical when fuel cell experiences water flooding. In
this work, the performance of a PEM fuel cell is investigated under
cathode flooding conditions. Two-dimensional partially flooded
GDL models based on the conservation laws and electrochemical
relations are proposed to study local current density distributions
along flow fields over a wide range of cell operating conditions.
The model results show a direct association between cathode inlet
humidity increases and that of average current density but the
system becomes more sensitive to flooding. The anode inlet
relative humidity shows a similar effect. Operating the cell at
higher temperatures would lead to higher average current densities
and the chance of system being flooded is reduced. In addition,
higher cathode stoichiometries prevent system flooding but the
average current density remains almost constant. The higher anode
stoichiometry leads to higher average current density and higher
sensitivity to cathode flooding.
Abstract: Many water supply systems in Australia are currently
undergoing significant reconfiguration due to reductions in long term
average rainfall and resulting low inflows to water supply reservoirs
since the second half of the 20th century. When water supply systems
undergo change, it is necessary to develop new operating rules,
which should consider climate, because the climate change is likely
to further reduce inflows. In addition, water resource systems are
increasingly intended to be operated to meet complex and multiple
objectives representing social, economic, environmental and
sustainability criteria. This is further complicated by conflicting
preferences on these objectives from diverse stakeholders. This paper
describes a methodology to develop optimum operating rules for
complex multi-reservoir systems undergoing significant change,
considering all of the above issues. The methodology is demonstrated
using the Grampians water supply system in northwest Victoria,
Australia. Initial work conducted on the project is also presented in
this paper.
Abstract: This paper proposes an architecture of dynamically
reconfigurable arithmetic circuit. Dynamic reconfiguration is a
technique to realize required functions by changing hardware
construction during operations. The proposed circuit is based on a
complex number multiply-accumulation circuit which is used
frequently in the field of digital signal processing. In addition, the
proposed circuit performs real number double precision arithmetic
operations. The data formats are single and double precision floating
point number based on IEEE754. The proposed circuit is designed
using VHDL, and verified the correct operation by simulations and
experiments.
Abstract: This work concerns the evolution and the maintenance
of an ontological resource in relation with the evolution of the corpus
of texts from which it had been built.
The knowledge forming a text corpus, especially in dynamic domains,
is in continuous evolution. When a change in the corpus occurs, the
domain ontology must evolve accordingly. Most methods manage
ontology evolution independently from the corpus from which it is
built; in addition, they treat evolution just as a process of knowledge
addition, not considering other knowledge changes. We propose a
methodology for managing an evolving ontology from a text corpus
that evolves over time, while preserving the consistency and the
persistence of this ontology.
Our methodology is based on the changes made on the corpus to
reflect the evolution of the considered domain - augmented surgery
in our case. In this context, the results of text mining techniques,
as well as the ARCHONTE method slightly modified, are used to
support the evolution process.
Abstract: This paper was to study the clothes dryer using waste
heat from a split type air conditioner with a capacity of 12,648 btu/h.
The drying chamber had a minimum cross section area with the size
of 0.5 x 1.0 m2. The chamber was constructed by sailcloth and was
inside folded with aluminium foil. Then, it was connected to the
condensing unit of an air conditioner. The experiment was carried out
in two aspects which were the clothes drying with and without
auxiliary fan unit. The results showed that the drying rate of clothes
in the chamber installed with and without auxiliary fan unit were
2.26 and 1.1 kg/h, respectively. In case of the chamber installed with
a auxiliary fan unit, the additional power of 0.011 kWh was
consumed and the drying rate was higher than that of clothes drying
without auxiliary fan unit. Without auxiliary fan unit installation, no
energy was required but there was a portion of hot air leaks away
through the punctured holes at the wall of the drying chamber, hence
the drying rate was dropped below. The drying rate of clothes drying
using waste heat was higher than natural indoor drying and
commercial dryer which their drying rate were 0.17 and 1.9 kg/h,
respectively. It was noted that the COP of the air conditioner did not
change during the operating of clothes drying.
Abstract: Wireless Sensor Networks (WSNs) have attracted the attention of many researchers. This has resulted in their rapid integration in very different areas such as precision agriculture,environmental monitoring, object and event detection and military surveillance. Due to the current WSN characteristics this technology is specifically useful in industrial areas where security, reliability and autonomy are basic, such as nuclear power plants, chemical plants, and others. In this paper we present a system based on WSNs to monitor environmental conditions around and inside a nuclear power plant, specifically, radiation levels. Sensor nodes, equipped with radiation sensors, are deployed in fixed positions throughout the plant. In addition, plant staff are also equipped with mobile devices with higher capabilities than sensors such as for example PDAs able to monitor radiation levels and other conditions around them. The system enables communication between PDAs, which form a Mobile Ad-hoc Wireless Network (MANET), and allows workers to monitor remote conditions in the plant. It is particularly useful during stoppage periods for inspection or in the event of an accident to prevent risk situations.
Abstract: Over the past decades, automatic face recognition has become a highly active research area, mainly due to the countless application possibilities in both the private as well as the public sector. Numerous algorithms have been proposed in the literature to cope with the problem of face recognition, nevertheless, a group of methods commonly referred to as appearance based have emerged as the dominant solution to the face recognition problem. Many comparative studies concerned with the performance of appearance based methods have already been presented in the literature, not rarely with inconclusive and often with contradictory results. No consent has been reached within the scientific community regarding the relative ranking of the efficiency of appearance based methods for the face recognition task, let alone regarding their susceptibility to appearance changes induced by various environmental factors. To tackle these open issues, this paper assess the performance of the three dominant appearance based methods: principal component analysis, linear discriminant analysis and independent component analysis, and compares them on equal footing (i.e., with the same preprocessing procedure, with optimized parameters for the best possible performance, etc.) in face verification experiments on the publicly available XM2VTS database. In addition to the comparative analysis on the XM2VTS database, ten degraded versions of the database are also employed in the experiments to evaluate the susceptibility of the appearance based methods on various image degradations which can occur in "real-life" operating conditions. Our experimental results suggest that linear discriminant analysis ensures the most consistent verification rates across the tested databases.
Abstract: Dill contains range of phytochemicals, such as vitamin C and polyphenols, which significantly contribute to their total antioxidant activity. The aim of the current research was to determine the best blanching method for processing of dill prior to microwave vacuum drying based on the content of phenolic compounds, vitamin C and free radical scavenging activity. Two blanching mediums were used – water and steam, and for part of the samples microwave pretreatment was additionally used. Evaluation of vitamin C, phenolic contents and scavenging of DPPH˙ radical in dried dill was performed. Blanching had an effect on all tested parameters and the blanching conditions are very important. After evaluation of the results, as the best method for dill pretreatment was established blanching at 90 °C for 30 seconds.
Abstract: This article presents the results of a study conducted to identify operational risks for information systems (IS) with service-oriented architecture (SOA). Analysis of current approaches to risk and system error classifications revealed that the system error classes were never used for SOA risk estimation. Additionally system error classes are not normallyexperimentally supported with realenterprise error data. Through the study several categories of various existing error classifications systems are applied and three new error categories with sub-categories are identified. As a part of operational risks a new error classification scheme is proposed for SOA applications. It is based on errors of real information systems which are service providers for application with service-oriented architecture. The proposed classification approach has been used to classify SOA system errors for two different enterprises (oil and gas industry, metal and mining industry). In addition we have conducted a research to identify possible losses from operational risks.
Abstract: Nowadays, desalination of salt water is considered an important industrial process. In many parts of the world, particularly in the gulf countries, the multi-stage flash (MSF) water desalination has an essential contribution in the production of fresh water. In this study, a simple mathematical model is defined to design a MSF desalination system and the feasibility of using the MSF desalination process in proximity of a 42 MW power plant is investigated. This power plant can just provide 10 ton/h superheated steam from low pressure (LP) section of heat recovery steam generator (HRSG) for thermal desalting system. The designed MSF system with gained output ratio (GOR) of 10.3 has 24 flashing stages and can produce 2480 ton/d of fresh water. The expected performance characteristics of the designed MSF desalination plant are determined. In addition, the effect of motive water pressure on the amount of non-condensable gases removed by water jet vacuum pumps is investigated.
Abstract: In this work we present the modelling of the induction
machine, taking into consideration the stator defects of the induction
machine. It is based on the theory of electromagnetic coupling of
electrical circuits. In fact, for the modelling of stationary defects such
as short circuit between turns in the same phase, we introduce only
in the matrix the coefficients of resistance and inductance of stator
and in the mutual inductance stator-rotor. These coefficients take
account the number of turns in short-circuit deducted from the total
number of turns in the same phase; in this way we obtain the number
of useful turns. In addition, all these faults involved, will be used for
the creation of the database that will be used to develop an automated
system failures of the induction machine.
Abstract: The application of agro-industrial waste in Aluminum
Metal Matrix Composites has been getting more attention as they
can reinforce particles in metal matrix which enhance the strength
properties of the composites. In addition, by applying these agroindustrial
wastes in useful way not only save the manufacturing cost
of products but also reduce the pollutions on environment. This
paper represents a literature review on a range of industrial wastes
and their utilization in metal matrix composites. The paper describes
the synthesis methods of agro-industrial waste filled metal matrix
composite materials and their mechanical, wear, corrosion, and
physical properties. It also highlights the current application and
future potential of agro-industrial waste reinforced composites in
aerospace, automotive and other construction industries.
Abstract: The iron loss is a source of detuning in vector controlled
induction motor drives if the classical rotor vector controller is used for
decoupling. In fact, the field orientation will not be satisfied and the
output torque will not truck the reference torque mostly used by Loss
Model Controllers (LMCs). In addition, this component of loss, among
others, may be excessive if the vector controlled induction motor is
driving light loads. In this paper, the series iron loss model is used to
develop a vector controller immune to iron loss effect and then an LMC
to minimize the total power loss using the torque generated by the speed
controller.
Abstract: This paper highlights the importance of the selection
of the building-s wall material,and the shortcomings of the most
commonly used framed structures with masonry infills .The
objective of this study is investigating the behavior of infill walls as
structural components in existing structures.Structural infill walls are
very important in structural behavior under earthquake effects.
Structural capacity under the effect of earthquake,displacement and
relative story displacement are affected by the structural irregularities
.The presence of nonstructural masonry infill walls can modify
extensively the global seismic behavior of framed buildings .The
stability and integrity of reinforced concrete frames are enhanced by
masonry infill walls. Masonry infill walls alter displacement and
base shear of the frame as well. Short columns have great
importance during earthquakes,because their failure may lead to
additional structural failures and result in total building collapse.
Consequently the effects of short columns are considered in this
study.