Abstract: This paper presents the variation of the dynamic
characteristics of a spindle with the change of bearing preload. The
correlations between the variation of bearing preload and fundamental
modal parameters were first examined by conducting vibration tests on
physical spindle units. Experimental measurements show that the
dynamic compliance and damping ratio associated with the
dominating modes were affected to vary with variation of the bearing
preload. When the bearing preload was slightly deviated from a
standard value, the modal frequency and damping ability also vary to
different extent, which further enable the spindle to perform with
different compliance. For the spindle used in this study, a standard
preload value set on bearings would enable the spindle to behave a
higher stiffness as compared with others with a preload variation. This
characteristic can be served as a reference to examine the variation of
bearing preload of spindle in assemblage or operation.
Abstract: It is known that residual welding deformations give
negative effect to processability and operational quality of welded
structures, complicating their assembly and reducing strength.
Therefore, selection of optimal technology, ensuring minimum
welding deformations, is one of the main goals in developing a
technology for manufacturing of welded structures.
Through years, JSC SSTC has been developing a theory for
estimation of welding deformations and practical activities for
reducing and compensating such deformations during welding
process. During long time a methodology was used, based on analytic
dependence. This methodology allowed defining volumetric changes
of metal due to welding heating and subsequent cooling. However,
dependences for definition of structures deformations, arising as a
result of volumetric changes of metal in the weld area, allowed
performing calculations only for simple structures, such as units, flat
sections and sections with small curvature. In case of complex 3D
structures, estimations on the base of analytic dependences gave
significant errors.
To eliminate this shortage, it was suggested to use finite elements
method for resolving of deformation problem. Here, one shall first
calculate volumes of longitudinal and transversal shortenings of
welding joints using method of analytic dependences and further,
with obtained shortenings, calculate forces, which action is
equivalent to the action of active welding stresses. Further, a finiteelements
model of the structure is developed and equivalent forces
are added to this model. Having results of calculations, an optimal
sequence of assembly and welding is selected and special measures to
reduce and compensate welding deformations are developed and
taken.
Abstract: This study aims to examine the role of career
advancement and job security as predictors of employee commitment
to their organization. Data was collected from 580 frontline
employees attached to two departments of 29 luxury hotels in
Peninsular Malaysia. Statistical results using Partial Least Squares
technique provided support for the proposed hypotheses. In view of
the findings, theoretical and practical implications are discussed.
Abstract: Bureaucracy reform program drives Indonesian
government to change their management to enhance their
organizational performance. Information technology became one of
strategic plan that organization tried to improve. Knowledge
management system is one of information system that supporting
knowledge management implementation in government which
categorized as people perspective, because this system has high
dependency in human interaction and participation. Strategic plan for
developing knowledge management system can be determine using
some of information system strategic methods. This research
conducted to define type of strategic method of information system,
stage of activity each method, strength and weakness. Literature
review methods used to identify and classify strategic methods of
information system, differentiate method type, categorize common
activities, strength and weakness. Result of this research are
determine and compare six strategic information system methods,
Balanced Scorecard and Risk Analysis believe as common strategic
method that usually used and have the highest excellence strength.
Abstract: The objectives of this research were to study the
influencing factors that contributed to the success of e-collaborative
in e-commerce of B2C (Business to Customer) business in Bangkok,
Thailand. The influencing factors included organization, people,
information technology and the process of e-collaborative. A
questionnaire was used to collect data from 200 small e-commerce
businesses and the path analysis was utilized as the tool for data
analysis.
By using the path analysis, it was revealed that the factors
concerning with organization, people and information technology
played an influence on e-collaborative process and the success of ecollaborative,
whereas the process of e-collaborative factor
manipulated its success. The findings suggested that B2C ecommerce
business in Thailand should opt in improvement approach
in terms of managerial structure, leaderships, staff’s skills and
knowledge, and investment of information technology in order to
capacitate higher efficiency of e-collaborative process that would
result in profit and competitive advantage.
Abstract: Construction in Finland is focusing increasingly on
renovation instead of conventional new construction, and this trend
will continue to grow in the coming years and decades. Renovation of
the large number of suburban residential apartment buildings built in
the 1960s and 1970s poses a particular challenge. However,
renovation projects are demanding for the residents of these
buildings, since they usually are uninitiated in construction issues. On
the other hand, renovation projects generally apply the operating
models of new construction.
Nevertheless, the residents of an existing residential apartment
building are some of the best experts on the site. Thus, in this
research project we applied a relational model in developing and
testing at case sites a planning process that employs interactive
planning methods. Current residents, housing company managers, the
city zoning manager, the contractor’s and prefab element supplier’s
representatives, professional designers and researchers all took part in
the planning. The entire interactive planning process progressed
phase by phase as the participants’ and designers’ concerted
discussion and ideation process, so that the end result was a
renovation plan desired by the residents.
Abstract: In the present work, detailed analysis on flow characteristics of a pair of immiscible liquids through horizontal pipeline is simulated by using ANSYS FLUENT 6.2. Moderately viscous oil and water (viscosity ratio = 107, density ratio = 0.89 and interfacial tension = 0.024 N/m) have been taken as system fluids for the study. Volume of Fluid (VOF) method has been employed by assuming unsteady flow, immiscible liquid pair, constant liquid properties, and co-axial flow. Meshing has been done using GAMBIT. Quadrilateral mesh type has been chosen to account for the surface tension effect more accurately. From the grid independent study, we have selected 47037 number of mesh elements for the entire geometry. Simulation successfully predicts slug, stratified wavy, stratified mixed and annular flow, except dispersion of oil in water, and dispersion of water in oil. Simulation results are validated with horizontal literature data and good conformity is observed. Subsequently, we have simulated the hydrodynamics (viz., velocity profile, area average pressure across a cross section and volume fraction profile along the radius) of stratified wavy and annular flow at different phase velocities. The simulation results show that in the annular flow, total pressure of the mixture decreases with increase in oil velocity due to the fact that pipe cross section is completely wetted with water. Simulated oil volume fraction shows maximum at the centre in core annular flow, whereas, in stratified flow, maximum value appears at upper side of the pipeline. These results are in accord with the actual flow configuration. Our findings could be useful in designing pipeline for transportation of crude oil.
Abstract: There is an essential need for obtaining the mathematical representation of fish body undulations, which can be used for designing and building new innovative types of marine propulsion systems with less environmental impact. This research work presents a case study to derive the mathematical model for fish body movement. Observation and capturing image methods were used in this study in order to obtain a mathematical representation of Clariasbatrachus fish (catfish). An experiment was conducted by using an aquarium with dimension 0.609 m x 0.304 m x 0.304 m, and a 0.5 m ruler was attached at the base of the aquarium. Progressive Scan Monochrome Camera was positioned at 1.8 m above the base of the aquarium to provide swimming sequences. Seven points were marked on the fish body using white marker to indicate the fish movement and measuring the amplitude of undulation. Images from video recordings (20 frames/s) were analyzed frame by frame using local coordinate system, with time interval 0.05 s. The amplitudes of undulations were obtained for image analysis from each point that has been marked on fish body. A graph of amplitude of undulations versus time was plotted by using computer to derive a mathematical fit. The function for the graph is polynomial with nine orders.
Abstract: The classroom of the 21st century is an ever changing forum for new and innovative thoughts and ideas. With increasing technology and opportunity, students have rapid access to information that only decades ago would have taken weeks to obtain. Unfortunately, new techniques and technology is not a cure for the fundamental problems that have plagued the classroom ever since education was established. Class size has been an issue long debated in academia. While it is difficult to pin point an exact number, it is clear that in this case more does not mean better. By looking into the success and pitfalls of classroom size the true advantages of smaller classes will become clear. Previously, one class was comprised of 50 students. Being seventeen and eighteen-year-old students, sometimes it was quite difficult for them to stay focused. To help them understand and gain much knowledge, a researcher introduced “The Theory of Multiple Intelligence” and this, in fact, enabled students to learn according to their own learning preferences no matter how they were being taught. In this lesson, the researcher designed a cycle of learning activities involving all intelligences so that everyone had equal opportunities to learn.
Abstract: Amyloid aggregation of polypeptides is related to a
growing number of pathologic states known as amyloid disorders. In
recent years, blocking or reversing amyloid aggregation via the use of
small compounds are considered as two useful approaches in
hampering the development of these diseases. In this research, we
have compared the ability of several manganese-salen derivatives, as
synthetic compounds, and apigenin, as a natural flavonoid, to inhibit
of hen egg-white lysozyme (HEWL) aggregation, as an in vitro
model system.
Different spectroscopic analyses such as Thioflavin T (ThT) and
Anilinonaphthalene-8-sulfonic acid (ANS) fluorescence, Congo red
(CR) absorbance along with transmission electron microscopy were
used in this work to monitor the HEWL aggregation kinetic and
inhibition. Our results demonstrated that both type of compounds
were capable to prevent the formation of lysozyme amyloid
aggregation in vitro. In addition, our data indicated that synthetic
compounds had higher activity to inhibit of the β-sheet structures
relative to natural compound. Regarding the higher antioxidant
activities of the salen derivatives, it can be concluded that in addition
to aromatic rings of each of the compounds, the potent antioxidant
properties of salen derivatives contributes to lower lysozyme fibril
accumulation.
Abstract: The use of low quality concrete has been identified as one of the main causes of the incessant collapse of buildings in Nigeria. Emphasis has been on the use of poor quality aggregates, poor workmanship and the use of lean concrete mix with low cement quantity as the reasons for the low quality of concrete used for building construction in Nigeria. Surveys conducted revealed that in the construction of most privately owned buildings where concrete trial mixes and concrete compressive strength quality assurance tests are not conducted, concretes used for building constructions are produced using the 1:2:4 mix ratio irrespective of the cement grade/strength class. In this paper, the possible role of the use of inappropriate cement grade/strength class as a cause of the incessant collapse of building in Nigeria is investigated. Investigation revealed that the compressive strengths of concrete cubes produced with Portland-limestone cement grade 32.5 using 1:2:4 and 1:1.5:3 mix ratios are less than the 25MPa and 30MPa cube strengths generally recommended for building superstructures and foundations respectively. Conversely, the compressive strengths of concrete cubes produced with Portland-limestone cement grade 42.5 using 1:2:4 and 1:1.5:3 mix ratios exceed the 25MPa and 30MPa generally recommended for building superstructures and foundations respectively. Thus, it can be concluded that the use of inappropriate cement grade (Portland-limestone cement grade 32.5), particularly for the construction of building foundations is a potential cause of the incessant collapse of buildings in Nigeria. It is recommended that the Standards Organisation of Nigeria should embark on creating awareness for Nigerians, particularly, the home owners and the roadside craftsmen that Portland-limestone cement grade 32.5 should not be used for the construction of building load-carrying members, particularly, building foundations in order to reduce the incessant incidence of collapsed building.
Abstract: A phase diagram of the Ag2SO4 - CaSO4 (Silver sulphate – Calcium Sulphate) binaries system using conductivity, XRD (X-Ray Diffraction Technique) and DTA (Differential Thermal Analysis) data is constructed. The eutectic reaction (liquid -» a-Ag2SO4 + CaSO4) is observed at 10 mole% CaSO4 and 645°C. Room temperature solid solubility limit up to 5.27 mole % of Ca 2+ in Ag2SO4 is set using X-ray powder diffraction and scanning electron microscopy results. All compositions beyond this limit are two-phase mixtures below and above the transition temperature (≈ 416°C). The bulk conductivity, obtained following complex impedance spectroscopy, is found decreasing with increase in CaSO4 content. Amongst other binary compositions, the 80AgSO4-20CaSO4 gave improved sinterability/packing density.
Abstract: Obesity, stunting and wasting problems among Thai school-aged children are increasing due to inappropriate food consumption behavior and poor environments for desirable nutritional behavior. Because of a low school lunch budget of only 0.40 USD per person per day, food quality is not up to nutritional standards. Therefore, the Health Department with the Education Ministry and the Thai Health Promotion Foundation have developed a quality school lunch project during 2009–2013. The program objectives were development and management of public policy to increase school lunch budget. The methods used a healthy public policy motivation process and movement in 241 local administrative organizations and 538 schools. The problem and solution research was organized to study school food and nutrition management, create a best practice policy mobilization model and hold a public hearing to motivate an increase of school meal funding. The results showed that local public policy has been motivated during 2009-2011 to increase school meal budget using local budgets. School children with best food consumption behavior and exercise increased from 13.2% in 2009 to 51.6% in 2013 and stunting decreased from 6.0% in 2009 to 4.7% in 2013. As the result of national policy motivation (2012-2013), the cabinet meeting on October 22, 2013 has approved an increase of school lunch budget from 0.40 USD to 0.62 USD per person per day. Thus, 5,800,469 school children nationwide have benefited from the budget increase.
Abstract: The purpose of this paper is to identify the main
challenges faced by companies in the timber construction sector and
to provide improvement opportunities that can be implemented on a
short-, medium- and long-term basis. To identify the challenges and
propose actions for each company a literature review and a multiple
case research were conducted using the Quick Scan Audit
Methodology. Finally, the findings and outcomes are compared with
each other to support companies in the timer construction sector
when implementing and restructuring their day-to-day activities.
Abstract: This paper presents the findings of an experimental investigation of important machining parameters for the horizontal boring tool modified to mouth with a horizontal lathe machine to bore an overlength workpiece. In order to verify a usability of a modified tool, design of experiment based on Taguchi method is performed. The parameters investigated are spindle speed, feed rate, depth of cut and length of workpiece. Taguchi L9 orthogonal array is selected for four factors three level parameters in order to minimize surface roughness (Ra and Rz) of S45C steel tubes. Signal to noise ratio analysis and analysis of variance (ANOVA) is performed to study an effect of said parameters and to optimize the machine setting for best surface finish. The controlled factors with most effect are depth of cut, spindle speed, length of workpiece, and feed rate in order. The confirmation test is performed to test the optimal setting obtained from Taguchi method and the result is satisfactory.
Abstract: Emotional Intelligence (EI) has been identified as an
important factor for corporate success. However, there are few
empirical findings on the impact of Strategic EI per se. The ooverall
objective of the study was to empirically examine the relationship
between the Strategic EI and Transformational Leadership style of
managers. Sixty four managers were selected from the banking
industry in Czech Republic. Genos EI Inventory, and the Multifactor
Leadership Questionnaire – Form 5X-Short were employed as the
major research instruments of the study. Descriptive and inferential
analyses of survey data were conducted using SPSS software.
Variations were observed among the components of Strategic EI
between males, and females. Study concludes positive a relationship
between Strategic EI of Czech managers and their transformational
leadership style. Improving awareness and usage of EI, will
contribute to facilitate career success through enhanced levels of
transformational leadership of managers.
Abstract: Compared with traditional distributed environment, the
net-centric environment brings on more demanding challenges for
information sharing with the characteristics of ultra-large scale and
strong distribution, dynamic, autonomy, heterogeneity, redundancy.
This paper realizes an information sharing model and a series of core
services, through which provides an open, flexible and scalable
information sharing platform.
Abstract: Sustainable tall buildings that provide comfortable,
healthy and efficient indoor environments are clearly desirable as the
densification of living and working space for the world’s increasing
population proceeds. For environmental concerns, these buildings
must also be energy efficient. One component of these tasks is the
provision of indoor air quality and thermal comfort, which can be
enhanced with natural ventilation by the supply of fresh air. Working
spaces can only be naturally ventilated with connections to the
outdoors utilizing operable windows, double facades, ventilation
stacks, balconies, patios, terraces and skygardens. Large amounts of
fresh air can be provided to the indoor spaces without mechanical
air-conditioning systems, which are widely employed in
contemporary tall buildings.
This paper tends to present the concept of natural ventilation for
sustainable tall office buildings in order to achieve healthy and
comfortable working spaces, as well as energy efficient
environments. Initially the historical evolution of ventilation
strategies for tall buildings is presented, beginning with natural
ventilation and continuing with the introduction of mechanical airconditioning
systems. Then the emergence of natural ventilation due
to the health and environmental concerns in tall buildings is handled,
and the strategies for implementing this strategy are revealed. In the
next section, a number of case studies that utilize this strategy are
investigated. Finally, how tall office buildings can benefit from this
strategy is discussed.
Abstract: Sustainability, being the urgent issue of our time, is
closely related with the innovations in technology. Nanotechnology
(NT), although not a new science, can be regarded relatively a new
science for buildings with brand new materials and applications. This
paper tends to give a research review of current and near future
applications of nanotechnology (NT) for achieving high-performance
and healthy buildings for a sustainable future. In the introduction, the
driving forces for the sustainability of construction industry are
explained. Then, the term NT is defined, and significance of
innovations in NT for a sustainable construction industry is revealed.
After presenting the application areas of NT and nanomaterials for
buildings with a number of cases, challenges in the adoption of this
technology are put forward, and finally the impacts of nanoparticles
and nanomaterials on human health and environment are discussed.
Abstract: Information technology is changing rapidly and the users’ expectations are also growing. Dealing with these changes in information technology, while satisfying the users’ needs and expectations is a big challenge. IT managers need to explore new mechanisms/strategies to enable them to cope with such challenges.
The objectives of this research are to identify the significant challenges that might face IT managers in higher education institutes in the face of the high and ever growing customer expectations and to propose possible solutions to cope with such high-speed changes in information technology.
To achieve these objectives, interviews with the IT professionals from different higher education institutes in Oman were conducted. In addition, documentation (printed and online) related to these institutions were studied and an intensive literature review of published work was examined.
The findings of this research are expected to give a better understanding of the challenges that might face the IT managers at higher education institutes. This acquired understanding is expected to highlight the importance of being adaptable and fast in keeping up with the ever-growing technological changes. Moreover, adopting different tools and technologies could assist IT managers in developing their organisations’ IT policies and strategies.