Abstract: Using ETABS software, this study analyzed 23
buildings to evaluate effects of mistakes during construction phase on
buildings structural behavior. For modelling, two different loadings
were assumed: 1) design loading and 2) loading due to the effects of
mistakes in construction phase. Research results determined that
considering traditional construction methods for buildings resulted in
a significant increase in dead loads and consequently intensified the
displacements and base-shears of buildings under seismic loads.
Abstract: South Africa has some regions which are susceptible
to moderate seismic activity. A peak ground acceleration of between
0.1g and 0.15g can be expected in the southern parts of the Western
Cape. Unreinforced Masonry (URM) is commonly used as a
construction material for 2 to 5 storey buildings in underprivileged
areas in and around Cape Town. URM is typically regarded as the
material most vulnerable to damage when subjected to earthquake
excitation. In this study, a three-storey URM building was analysed
by applying seven earthquake time-histories, which can be expected
to occur in South Africa using a finite element approach.
Experimental data was used to calibrate the in- and out-of-plane
stiffness of the URM. The results indicated that tensile cracking of
the in-plane piers was the dominant failure mode. It is concluded that
URM buildings of this type are at risk of failure especially if
sufficient ductility is not provided. The results also showed that
connection failure must be investigated further.
Abstract: The thermo-mechanical behaviour of concrete energy
pile foundations with different single and double U-tube shapes
incorporated was analysed using the Comsol Multi-physics package.
For the analysis, a 3D numerical model in real scale of the concrete
pile and surrounding soil was simulated regarding actual operation of
ground heat exchangers (GHE) and the surrounding ambient
temperature. Based on initial ground temperature profile measured in
situ, tube inlet temperature was considered to range from 6oC to 0oC
(during the contraction process) over a 30-day period. Extra thermal
stresses and deformations were calculated during the simulations and
differences arising from the use of two different systems (single-tube
and double-tube) were analysed. The results revealed no significant
difference for extra thermal stresses at the centre of the pile in either
system. However, displacements over the pile length were found to
be up to 1.5-fold higher in the double-tube system than the singletube
system.
Abstract: This paper discusses about the findings of preliminary
survey on MATLAB software learning among power electronics
students. One of the main focuses of power electronics course is on
DC to DC boost convertors, because boost convertors are generally
used in different industrial and non industrial applications. Population
samples of this study were randomly selected final year bachelor of
electronics and electrical engineering students from University Tun
Hussein Onn Malaysia (UTHM).As per the results from the survey
questioner analysis, almost eighty percent students are facing
problem and difficulties in Dc to Dc boost convertors experimental
understanding without using MATLAB simulink package. As per
finding of this study it is clear that MATLAB play an effective and
efficient function for better understanding of boost convertors
experimental work among power electronics learners.
Abstract: Curcuma longa L. (Zingiberaceae), commonly known
as turmeric, has a long history of traditional uses for culinary
purposes as a spice and a food colorant. The present study aimed to
document the ethnobotanical knowledge about Curcuma longa, and
to assess the variation in the herbalists’ experience in Northeastern
Algeria. Data were collected using semi-structured questionnaires
and direct interviews with 30 herbalists. Ethnobotanical indices,
including the fidelity level (FL%), the relative frequency citation
(RFC), and use value (UV) were determined by quantitative methods.
Diversity in the level of knowledge was analyzed using univariate,
non-parametric, and multivariate statistical methods. Three main
categories of uses were recorded for C. longa: for food, for medicine,
and for cosmetic purposes. As a medicine, turmeric was used for the
treatment of gastrointestinal, dermatological, and hepatic diseases.
Medicinal and food uses were correlated with both forms of
preparation (rhizome and powder). The age group did not influence
the use. Multivariate analyses showed a significant variation in
traditional knowledge, associated with the use value, origin, quality,
and efficacy of the drug. The findings suggested that the geographical
origin of C. longa affected the use in Algeria.
Abstract: This paper is drawn from a wider study of the
management of gender, age and disability diversity in the banking
sector in the Kingdom of Saudi Arabia (KSA), which aims to develop
a framework for diversity management (DM) in this sector. The
paper focuses on the management of disability diversity. The purpose
of the paper is to assist in understanding disability DM in the banking
sector in KSA and to make suggestions for its enhancement. Hence, it
contributes to filling a research gap, as there is a dearth of literature
on disability DM, in KSA in general, and in the banking sector
specifically.
Discrimination against people with disabilities is a social issue that
has not been entirely overcome in any society. However, in KSA,
Islam informs almost every aspect of daily life including work, and
Islam is against discrimination. Hence, in KSA, there are regulations
to accommodate people with disabilities; however, employers are still
free not to hire job applicants with disabilities specifically because of
their condition. Indeed, disabled people are almost entirely absent
from the labour market.
There are 12 Saudi-owned or part-Saudi-owned banks in KSA and
two managers from each of these were interviewed, making a total of
24. The interviews aimed to investigate empirically the understanding
of managers in the banking sector in KSA of diversity management,
including disability DM, in the banking sector. The interview data
were analysed using thematic analysis. Two interviewees stated that
banks used the employment of people with disabilities to enhance
their corporate image, while five expressed the opinion that disabled
employees could contribute to the bank provided they did not have to
deal with customers face-to-face. Nine of the interviewees perceived
that disabled employees could be of value to the bank for their own
sake, not only in ‘behind the scenes’ roles. Another two interviewees
mentioned that employing disabled people could be part of the bank’s
community service programme and one thought it would be part of
the bank’s Saudisation efforts. The remaining five interviewees did
not know how disabled people could contribute to the bank.
The findings show that disability DM in the banking sector in
KSA is a relatively new concept, and is not yet well understood. In
the light of the findings, in order to achieve the purpose of the paper,
the following suggestions were made for the enhancement of
disability DM in the banking sector in KSA. A change in attitudes
towards disabled people is necessary. Such a change in the workplace
can only be achieved if a top-down approach is taken to the
integration of disabled people. Hence, it is suggested that
management and employees follow a course in disability awareness.
Further, a diversity officer in the HR department could enhance the
integration of disabled people into the banking workforce. It is also
suggested that greater government support is required through closely
monitored and enforced anti-discrimination legislation. Moreover,
flexible working arrangements such as part-time work would
facilitate the employment of disabled people and benefit other groups
of employees.
Abstract: Many quality models have been used to measure egovernment
portals quality. However, the absence of an international
consensus for e-government portals quality models results in many
differences in terms of quality attributes and measures. The aim of
this paper is to compare and analyze the existing e-government
quality models proposed in literature (those that are based on ISO
standards and those that are not) in order to propose guidelines to
build a good and useful e-government portals quality model. Our
findings show that, there is no e-government portal quality model
based on the new international standard ISO 25010. Besides that, the
quality models are not based on a best practice model to allow
agencies to both; measure e-government portals quality and identify
missing best practices for those portals.
Abstract: The crude oil in an oil well exists in various phases
such as gas, seawater, and sand, as well as oil. Therefore, a phase
separator is needed at the front of a single-phase pump for
pressurization and transfer. On the other hand, the application of a
multiphase pump can provide such advantages as simplification of the
equipment structure and cost savings, because there is no need for a
phase separation process. Therefore, the crude oil transfer method
using a multiphase pump is being applied to recently developed oil
wells. Due to this increase in demand, technical demands for the
development of multiphase pumps are sharply increasing, but the
progress of research into related technologies is insufficient, due to the
nature of multiphase pumps that require high levels of skills. This
study was conducted to verify the reliability of pump performance
evaluation using numerical analysis, which is the basis of the
development of a multiphase pump. For this study, a model was
designed by selecting the specifications of this study. The performance
of the designed model was evaluated through numerical analysis and
experiment. The results of the performance evaluation were compared
to verify the reliability of the result using numerical analysis.
Abstract: In structures, stress concentration is a factor of fatigue
fracture. Basically, the stress concentration is a phenomenon that
should be avoided. However, it is difficult to avoid the stress
concentration. Therefore, relaxation of the stress concentration is
important. The stress concentration arises from notches and circular
holes. There is a relaxation method that a composite patch covers a
notch and a circular hole. This relaxation method is used to repair
aerial wings, but it is not systematized. Composites are more
expensive than single materials. Accordingly, we propose the
relaxation method that a single material patch covers a notch and a
circular hole, and aim to systematize this relaxation method.
We performed FEA (Finite Element Analysis) about an object by
using a three-dimensional FEA model. The object was that a patch
adheres to a plate with a circular hole. And, a uniaxial tensile load acts
on the patched plate with a circular hole. In the three-dimensional FEA
model, it is not easy to model the adhesion layer. Basically, the yield
stress of the adhesive is smaller than that of adherents. Accordingly,
the adhesion layer gets to plastic deformation earlier than the adherents
under the yield load of adherents. Therefore, we propose the
three-dimensional FEA model which is applied a nonlinear elastic
region to the adhesion layer. The nonlinear elastic region was
calculated by a bilinear approximation. We compared the analysis
results with the tensile test results to confirm whether the analysis
model has usefulness. As a result, the analysis results agreed with the
tensile test results. And, we confirmed that the analysis model has
usefulness.
As a result that the three-dimensional FEA model was used to the
analysis, it was confirmed that an out-of-plane deformation occurred
to the patched plate with a circular hole. The out-of-plane deformation
causes stress increase of the patched plate with a circular hole.
Therefore, we investigated that the out-of-plane deformation affects
relaxation of the stress concentration in the plate with a circular hole
on this relaxation method. As a result, it was confirmed that the
out-of-plane deformation inhibits relaxation of the stress concentration
on the plate with a circular hole.
Abstract: Supermarkets are the most electricity-intensive type of
commercial buildings. The unsuitable indoor environment of a
supermarket provided by abnormal HVAC operations incurs waste
energy consumption in refrigeration systems. This current study
briefly describes significantly solid backgrounds and proposes easyto-
use analysis terminology for investigating the impact of HVAC
operations on refrigeration power consumption using the field-test
data obtained from building automation system (BAS). With solid
backgrounds and prior knowledge, expected energy interactions
between HVAC and refrigeration systems are proposed through
Pearson’s correlation analysis (R value) by considering correlations
between equipment power consumption and dominantly independent
variables (driving force conditions).The R value can be conveniently
utilized to evaluate how strong relations between equipment
operations and driving force parameters are. The calculated R values
obtained from field data are compared to expected ranges of R values
computed by energy interaction methodology. The comparisons can
separate the operational conditions of equipment into faulty and
normal conditions. This analysis can simply investigate the condition
of equipment operations or building sensors because equipment could
be abnormal conditions due to routine operations or faulty
commissioning processes in field tests. With systematically solid and
easy-to-use backgrounds of interactions provided in the present
article, the procedures can be utilized as a tool to evaluate the proper
commissioning and routine operations of HVAC and refrigeration
systems to detect simple faults (e.g. sensors and driving force
environment of refrigeration systems and equipment set-point) and
optimize power consumption in supermarket buildings. Moreover,
the analysis will be used to further study the FDD research for
supermarkets in future.
Abstract: Recently, there have been a lot of earthquakes in Japan.
It is necessary to promote seismic isolation devices for buildings. The
devices have been hardly diffused in attached houses, because the
devices are very expensive. We should develop a low-cost seismic
isolation device for detached houses. We suggested a new seismic
isolation device which uses a two-layer circular tube as a unit. If
hysteresis is produced in the two-layer circular tube under lateral
compression load, we think that the two-layer circular tube can have
energy absorbing capacity. It is necessary to contact the outer layer
and the inner layer to produce hysteresis. We have previously reported
how the inner layer comes in contact with the outer layer from a
perspective of analysis used mechanics of materials. We have clarified
that the inner layer comes in contact with the outer layer under a lateral
compression load. In this paper, we explored contact area between the
outer layer and the inner layer under a lateral compression load by
using FEA. We think that changing the inner layer’s thickness is
effective in increase the contact area. In order to change the inner
layer’s thickness, we changed the shape of the inner layer. As a result,
the contact area changes depending on the inner layer’s thickness.
Additionally, we experimented to check whether hysteresis occurs in
fact. As a consequence, we can reveal hysteresis in the two-layer
circular tube under the condition.
Abstract: Apps are today the most important possibility to adapt
mobile phones and computers to fulfill the special needs of their
users. Location- and context-sensitive programs are hereby the key to
support the interaction of the user with his/her environment and also
to avoid an overload with a plenty of dispensable information. The
contribution shows, how a trusted, secure and really bi-directional
communication and interaction among users and their environment
can be established and used, e.g. in the field of home automation.
Abstract: The study identified the socio-economic and
demographic factors of both married and unmarried females in third
world countries. Almost all the countries have same problems but we
have selected Pakistan as a sample country. The main purpose of this
study was to examine which factors forced women to participate in
labor market. So the best technique of data collection was survey of
both married and unmarried females between the ages of 20 to 49.
Two models (probit and logit) were used to analyze the factors which
effect on FLFP. The result showed that some factors e.g. age;
education and marital status have significant effect on FLFP. The
findings showed that educated women and those who belong to joint
families are more participate because of financial pressure.
Abstract: In new energy development, wind power has boomed.
It is due to the proliferation of wind parks and their operation in
supplying the national electric grid with low cost and clean resources.
Hence, there is an increased need to establish a proactive
maintenance for wind turbine machines based on remote control and
monitoring. That is necessary with a real-time wireless connection in
offshore or inaccessible locations while the wired method has many
flaws. The objective of this strategy is to prolong wind turbine
lifetime and to increase productivity. The hardware of a remote
control and monitoring system for wind turbine parks is designed. It
takes advantage of GPRS or Wi-Max wireless module to collect data
measurements from different wind machine sensors through IP based
multi-hop communication. Computer simulations with Proteus ISIS
and OPNET software tools have been conducted to evaluate the
performance of the studied system. Study findings show that the
designed device is suitable for application in a wind park.
Abstract: Robotics provides answers to amputees. The most
expensive solutions surgically connect the prosthesis to nerve endings.
There are also several types of non-invasive technologies that recover
nerve messages passing through the muscles. After analyzing these
messages, myoelectric prostheses perform the desired movement.
The main goal is to avoid all surgeries, which can be heavy and offer
cheaper alternatives. For an amputee, we use valid muscles to recover
the electrical signal involved in a muscle movement. EMG sensors
placed on the muscle allows us to measure a potential difference,
which our program transforms into control for a robotic arm with two
degrees of freedom. We have shown the feasibility of non-invasive
prostheses with two degrees of freedom. Signal analysis and an
increase in degrees of freedom is still being improved.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: Due to the advancement of Internet technology, online
learning is widely used in higher education institutions. Online
learning offers several means of communication, including online
forum. Through online forum, students and instructors are able to
discuss and share their knowledge and expertise without having a
need to attend the face-to-face, ordinary classroom session. The
purposes of this study are to analyze the students’ levels of
participation and critical thinking, types of action and factors
influencing their participation in online forum. A total of 41
postgraduate students undertaking a course in educational technology
from a public university in Malaysia were involved in this study. In
this course, the students participated in a weekly online forum as part
of the course requirement. Based on the log data file extracted from
the online forum, the students’ type of actions (view, add, update,
delete posts) and their levels of participation (passive, moderate or
active) were identified. In addition, the messages posted in the forum
were analyzed to gauge their level of critical thinking. Meanwhile,
the factors that might influence their online forum participation were
measured using a 24-items questionnaire. Based on the log data, a
total of 105 posts were sent by the participants. In addition, the
findings show that (i) majority of the students are moderate
participants, with an average of two to three posts per person, (ii)
viewing posts are the most frequent type of action (85.1%), and
followed by adding post (9.7%). Furthermore, based on the posts
they made, the most frequent type of critical thinking observed was
justification (50 input or 19.0%), followed by linking ideas and
interpretation (47 input or 18%), and novelty (38 input or 14.4%).
The findings indicate that online forum allows for social interaction
and can be used to measure the students’ critical thinking skills. In
order to achieve this, monitoring students’ activities in the online
forum is recommended.
Abstract: Students’ achievement and motivation in learning
English in Malaysia is a worrying trend as it is lagging behind several
other countries in Asia. Thus, necessary actions have to be taken by
the parties concerned to overcome this problem. The purpose of this
research was to study the effects of drill and practice courseware on
students’ achievement and motivation in learning English language.
A multimedia courseware was developed for this purpose. The
independent variable was the drill and practice courseware while the
dependent variables were the students’ achievement and motivation.
Their achievement was measured using pre-test and post-test scores,
while motivation was measured using a questionnaire. A total of 60
students from three vernacular primary schools in a northern state in
Malaysia were randomly selected in this study. The findings indicate:
(1) a significant difference between the students’ pre-test and posttest
scores after using the courseware, (2) no significant difference in
the achievement score between male and female students after using
the courseware, (3) a significant difference in motivation score
between the female and the male students, and (4) while the female
students scored significantly higher than the male students in the
aspects of relevance, confidence and satisfaction, no significant
difference in terms of attention was observed between them. Overall,
the findings clearly indicate that although the female students are
significantly more motivated than their male students, they are
equally good in terms of achievement after learning from the
courseware. Through this study, the drill and practice courseware is
proven to influence the students’ learning and motivation.
Abstract: The asynchronous discussion forum is one of the most
widely used activities in learning management system environment.
Online forum allows participants to interact, construct knowledge,
and can be used to complement face to face sessions in blended
learning courses. However, to what extent do the students perceive
the benefits or advantages of forum remain to be seen. Through
content and social network analyses, instructors will be able to gauge
the students’ engagement and knowledge construction level. Thus,
this study aims to analyze the students’ level of knowledge
construction and their participation level that occur through online
discussion. It also attempts to investigate the relationship between the
level of knowledge construction and their social interaction patterns.
The sample involves 23 students undertaking a master course in one
public university in Malaysia. The asynchronous discussion forum
was conducted for three weeks as part of the course requirement. The
finding indicates that the level of knowledge construction is quite
low. Also, the density value of 0.11 indicating the overall
communication among the participants in the forum is low. This
study reveals that strong and significant correlations between SNA
measures (in-degree centrality, out-degree centrality) and level of
knowledge construction. Thus, allocating these active students in
different group aids the interactive discussion takes place. Finally,
based upon the findings, some recommendations to increase students’
level of knowledge construction and also for further research are
proposed.
Abstract: Lately, asynchronous discussion forum is integrated in
higher educational institutions as it may increase learning process,
learners’ understanding, achievement and knowledge construction.
The asynchronous discussion forum is used to complement the
traditional, face-to-face learning session in hybrid learning courses.
However, studies have proven that students’ engagement in online
forums is still unconvincing. Thus, the aim of this study is to
investigate the motivating factors and obstacles that affect the
learners’ engagement in asynchronous discussion forum. This study
is carried out in one of the public higher educational institutions in
Malaysia with 18 postgraduate students as samples. The authors have
developed a 40-items questionnaire based on literature review. The
results indicate several factors that have encouraged or limited
students’ engagement in asynchronous discussion forum: (a) the
practices or behaviors of peers, or instructors, (b) the needs for the
discussions, (c) the learners’ personalities, (d) constraints in
continuing the discussion forum, (e) lack of ideas, (f) the level of
thoughts, (g) the level of knowledge construction, (h) technical
problems, (i) time constraints and (j) misunderstanding. This study
suggests some recommendations to increase the students’
engagement in online forums. Finally, based upon the findings, some
implications are proposed for further research.