Abstract: The paper compares different channel models used for
modeling Broadband Power-Line Communication (BPLC) system.
The models compared are Zimmermann and Dostert, Philipps,
Anatory et al and Anatory et al generalized Transmission Line (TL)
model. The validity of each model was compared in time domain
with ATP-EMTP software which uses transmission line approach. It
is found that for a power-line network with minimum number of
branches all the models give similar signal/pulse time responses
compared with ATP-EMTP software; however, Zimmermann and
Dostert model indicates the same amplitude but different time delay.
It is observed that when the numbers of branches are increased only
generalized TL theory approach results are comparable with ATPEMTP
results. Also the Multi-Carrier Spread Spectrum (MC-SS)
system was applied to check the implication of such behavior on the
modulation schemes. It is observed that using Philipps on the
underground cable can predict the performance up to 25dB better
than other channel models which can misread the actual performance
of the system. Also modified Zimmermann and Dostert under
multipath can predict a better performance of about 5dB better than
the actual predicted by Generalized TL theory. It is therefore
suggested for a realistic BPLC system design and analyses the model
based on generalized TL theory be used.
Abstract: We proposed a technique to identify road traffic
congestion levels from velocity of mobile sensors with high accuracy
and consistent with motorists- judgments. The data collection utilized
a GPS device, a webcam, and an opinion survey. Human perceptions
were used to rate the traffic congestion levels into three levels: light,
heavy, and jam. Then the ratings and velocity were fed into a
decision tree learning model (J48). We successfully extracted vehicle
movement patterns to feed into the learning model using a sliding
windows technique. The parameters capturing the vehicle moving
patterns and the windows size were heuristically optimized. The
model achieved accuracy as high as 99.68%. By implementing the
model on the existing traffic report systems, the reports will cover
comprehensive areas. The proposed method can be applied to any
parts of the world.
Abstract: The third generation (3G) of cellular system adopted
the spread spectrum as solution for the transmission of the data in the
physical layer. Contrary to systems IS-95 or CDMAOne (systems
with spread spectrum of the preceding generation), the new standard,
called Universal Mobil Telecommunications System (UMTS), uses
long codes in the down link. The system is conceived for the vocal
communication and the transmission of the data. In particular, the
down link is very important, because of the asymmetrical request of
the data, i.e., more remote loading towards the mobiles than towards
the basic station. Moreover, the UMTS uses for the down link an
orthogonal spreading out with a variable factor of spreading out
(OVSF for Orthogonal Variable Spreading Factor). This
characteristic makes it possible to increase the flow of data of one or
more users by reducing their factor of spreading out without
changing the factor of spreading out of other users. In the current
standard of the UMTS, two techniques to increase the performances
of the down link were proposed, the diversity of sending antenna and
the codes space-time. These two techniques fight only fainding. The
receiver proposed for the mobil station is the RAKE, but one can
imagine a receiver more sophisticated, able to reduce the interference
between users and the impact of the coloured noise and interferences
to narrow band. In this context, where the users have long codes
synchronized with variable factor of spreading out and ignorance by
the mobile of the other active codes/users, the use of the sequences of
code pseudo-noises different lengths is presented in the form of one
of the most appropriate solutions.
Abstract: Background: Widespread use of chemotherapeutic
drugs in the treatment of cancer has lead to higher health hazards
among employee who handle and administer such drugs, so nurses
should know how to protect themselves, their patients and their work
environment against toxic effects of chemotherapy. Aim of this study
was carried out to examine the effect of chemotherapy safety protocol
for oncology nurses on their protective measure practices. Design: A
quasi experimental research design was utilized. Setting: The study
was carried out in oncology department of Menoufia university
hospital and Tanta oncology treatment center. Sample: A
convenience sample of forty five nurses in Tanta oncology treatment
center and eighteen nurses in Menoufiya oncology department.
Tools: 1. an interviewing questionnaire that covering sociodemographic
data, assessment of unit and nurses' knowledge about
chemotherapy. II: Obeservational check list to assess nurses' actual
practices of handling and adminestration of chemotherapy. A base
line data were assessed before implementing Chemotherapy Safety
protocol, then Chemotherapy Safety protocol was implemented, and
after 2 monthes they were assessed again. Results: reveled that 88.9%
of study group I and 55.6% of study group II improved to good total
knowledge scores after educating on the safety protocol, also 95.6%
of study group I and 88.9% of study group II had good total practice
score after educating on the safety protocol. Moreover less than half
of group I (44.4%) reported that heavy workload is the most barriers
for them, while the majority of group II (94.4%) had many barriers
for adhering to the safety protocol such as they didn’t know the
protocol, the heavy work load and inadequate equipment.
Conclusions: Safety protocol for Oncology Nurses seemed to have
positive effect on improving nurses' knowledge and practice.
Recommendation: chemotherapy safety protocol should be instituted
for all oncology nurses who are working in any oncology unit and/ or
center to enhance compliance, and this protocol should be done at
frequent intervals.
Abstract: Importance of software quality is increasing leading to development of new sophisticated techniques, which can be used in constructing models for predicting quality attributes. One such technique is Artificial Neural Network (ANN). This paper examined the application of ANN for software quality prediction using Object- Oriented (OO) metrics. Quality estimation includes estimating maintainability of software. The dependent variable in our study was maintenance effort. The independent variables were principal components of eight OO metrics. The results showed that the Mean Absolute Relative Error (MARE) was 0.265 of ANN model. Thus we found that ANN method was useful in constructing software quality model.
Abstract: A filter is used to remove undesirable frequency information from a dynamic signal. This paper shows that the Znotch filter filtering technique can be applied to remove the noise nuisance from a machining signal. In machining, the noise components were identified from the sound produced by the operation of machine components itself such as hydraulic system, motor, machine environment and etc. By correlating the noise components with the measured machining signal, the interested components of the measured machining signal which was less interfered by the noise, can be extracted. Thus, the filtered signal is more reliable to be analysed in terms of noise content compared to the unfiltered signal. Significantly, the I-kaz method i.e. comprises of three dimensional graphical representation and I-kaz coefficient, Z∞ could differentiate between the filtered and the unfiltered signal. The bigger space of scattering and the higher value of Z∞ demonstrated that the signal was highly interrupted by noise. This method can be utilised as a proactive tool in evaluating the noise content in a signal. The evaluation of noise content is very important as well as the elimination especially for machining operation fault diagnosis purpose. The Z-notch filtering technique was reliable in extracting noise component from the measured machining signal with high efficiency. Even though the measured signal was exposed to high noise disruption, the signal generated from the interaction between cutting tool and work piece still can be acquired. Therefore, the interruption of noise that could change the original signal feature and consequently can deteriorate the useful sensory information can be eliminated.
Abstract: Post growth annealing of solution grown ZnO
nanowire array is performed under controlled oxygen ambience. The
role of annealing over surface defects and their consequence on
dark/photo-conductivity and photosensitivity of nanowire array is
investigated. Surface defect properties are explored using various
measurement tools such as contact angle, photoluminescence, Raman
spectroscopy and XPS measurements. The contact angle of the NW
films reduces due to oxygen annealing and nanowire film surface
changes from hydrophobic (96°) to hydrophilic (16°). Raman and
XPS spectroscopy reveal that oxygen annealing improves the crystal
quality of the nanowire films. The defect band emission intensity
(relative to band edge emission, ID/IUV) reduces from 1.3 to 0.2 after
annealing at 600 °C at 10 SCCM flow of oxygen. An order
enhancement in dark conductivity is observed in O2 annealed
samples, while photoconductivity is found to be slightly reduced due
to lower concentration of surface related oxygen defects.
Abstract: This paper proposes a new decision making approch
based on quantitative possibilistic influence diagrams which are
extension of standard influence diagrams in the possibilistic framework.
We will in particular treat the case where several expert
opinions relative to value nodes are available. An initial expert assigns
confidence degrees to other experts and fixes a similarity threshold
that provided possibility distributions should respect. To illustrate our
approach an evaluation algorithm for these multi-source possibilistic
influence diagrams will also be proposed.
Abstract: This paper examines many mathematical methods for
molding the hourly price forward curve (HPFC); the model will be
constructed by numerous regression methods, like polynomial
regression, radial basic function neural networks & a furrier series.
Examination the models goodness of fit will be done by means of
statistical & graphical tools. The criteria for choosing the model will
depend on minimize the Root Mean Squared Error (RMSE), using the
correlation analysis approach for the regression analysis the optimal
model will be distinct, which are robust against model
misspecification. Learning & supervision technique employed to
determine the form of the optimal parameters corresponding to each
measure of overall loss. By using all the numerical methods that
mentioned previously; the explicit expressions for the optimal model
derived and the optimal designs will be implemented.
Abstract: It is sometimes difficult to differentiate between
innocent murmurs and pathological murmurs during auscultation. In
these difficult cases, an intelligent stethoscope with decision support
abilities would be of great value. In this study, using a dog model,
phonocardiographic recordings were obtained from 27 boxer dogs
with various degrees of aortic stenosis (AS) severity. As a reference
for severity assessment, continuous wave Doppler was used. The data
were analyzed with recurrence quantification analysis (RQA) with
the aim to find features able to distinguish innocent murmurs from
murmurs caused by AS. Four out of eight investigated RQA features
showed significant differences between innocent murmurs and
pathological murmurs. Using a plain linear discriminant analysis
classifier, the best pair of features (recurrence rate and entropy)
resulted in a sensitivity of 90% and a specificity of 88%. In
conclusion, RQA provide valid features which can be used for
differentiation between innocent murmurs and murmurs caused by
AS.
Abstract: In this note the notion of interval-valued fuzzy BG-algebras (briefly, i-v fuzzy BG-algebras), the level and strong level BG-subalgebra is introduced. Then we state and prove some theorems which determine the relationship between these notions and BG-subalgebras. The images and inverse images of i-v fuzzy BG-subalgebras are defined, and how the homomorphic images and inverse images of i-v fuzzy BG-subalgebra becomes i-v fuzzy BG-algebras are studied.
Abstract: The triumph of inductive neuro-stimulation since its rediscovery in the 1980s has been quite spectacular. In lots of branches ranging from clinical applications to basic research this system is absolutely indispensable. Nevertheless, the basic knowledge about the processes underlying the stimulation effect is still very rough and rarely refined in a quantitative way. This seems to be not only an inexcusable blank spot in biophysics and for stimulation prediction, but also a fundamental hindrance for technological progress. The already very sophisticated devices have reached a stage where further optimization requires better strategies than provided by simple linear membrane models of integrate-and-fire style. Addressing this problem for the first time, we suggest in the following text a way for virtual quantitative analysis of a stimulation system. Concomitantly, this ansatz seems to provide a route towards a better understanding by using nonlinear signal processing and taking the nerve as a filter that is adapted for neuronal magnetic stimulation. The model is compact and easy to adjust. The whole setup behaved very robustly during all performed tests. Exemplarily a recent innovative stimulator design known as cTMS is analyzed and dimensioned with this approach in the following. The results show hitherto unforeseen potentials.
Abstract: Deprivation indices are widely used in public health
study. These indices are also referred as the index of inequalities or
disadvantage. Even though, there are many indices that have been
built before, it is believed to be less appropriate to use the existing
indices to be applied in other countries or areas which had different
socio-economic conditions and different geographical characteristics.
The objective of this study is to construct the index based on the
geographical and socio-economic factors in Peninsular Malaysia
which is defined as the weighted household-based deprivation index.
This study has employed the variables based on household items,
household facilities, school attendance and education level obtained
from Malaysia 2000 census report. The factor analysis is used to
extract the latent variables from indicators, or reducing the
observable variable into smaller amount of components or factor.
Based on the factor analysis, two extracted factors were selected,
known as Basic Household Amenities and Middle-Class Household
Item factor. It is observed that the district with a lower index values
are located in the less developed states like Kelantan, Terengganu
and Kedah. Meanwhile, the areas with high index values are located
in developed states such as Pulau Pinang, W.P. Kuala Lumpur and
Selangor.
Abstract: Some methodologies were compared in providing
erosion maps of surface, rill and gully and erosion features, in
research which took place in the Varamin sub-basin, north-east
Tehran, Iran. A photomorphic unit map was produced from
processed satellite images, and four other maps were prepared by the
integration of different data layers, including slope, plant cover,
geology, land use, rocks erodibility and land units. Comparison of
ground truth maps of erosion types and working unit maps indicated
that the integration of land use, land units and rocks erodibility layers
with satellite image photomorphic units maps provide the best
methods in producing erosion types maps.
Abstract: Rapid Application Development (RAD) enables ever
expanding needs for speedy development of computer application
programs that are sophisticated, reliable, and full-featured. Visual
Basic was the first RAD tool for the Windows operating system, and
too many people say still it is the best. To provide very good
attraction in visual basic 6 applications, this paper directing to use
VRML scenes over the visual basic environment.
Abstract: Fermented beverages have high expression in the
market for beverages in general, is increasingly valued in situations
where the characteristic aroma and flavor of the material that gave
rise to them are kept after processing. This study aimed to develop a
distilled beverage from passion fruit, and assess, by sensory tests and
chromatographic profile, the influence of different treatments (FM1-
spirit with pulp addiction and FM2 – spirit with bigger ratio of pulp
in must) in the setting of volatiles in the fruit drink, and performing
chemical characterization taking into account the main parameters of
quality established by the legislation. The chromatograms and the
first sensorial tests had indicated that sample FM1 possess better
characteristics of aroma, as much of how much quantitative the
qualitative point of view. However, it analyzes it sensorial end
(preference test) disclosed the biggest preference of the cloth provers
for sample FM2-2 (note 7.93), being the attributes of decisive color
and flavor in this reply, confirmed for the observed values lowest of
fixed and total acidity in the samples of treatment FM2.
Abstract: This paper identifies five key design characteristics of
production scheduling software systems in printed circuit board (PCB) manufacturing. The authors consider that, in addition to an effective scheduling engine, a scheduling system should be able to
process a preventative maintenance calendar, to give the user the
flexibility to handle data using a variety of electronic sources, to run
simulations to support decision-making, and to have simple and
customisable graphical user interfaces. These design considerations
were the result of a review of academic literature, the evaluation of
commercial applications and a compilation of requirements of a PCB manufacturer. It was found that, from those systems that were evaluated, those that effectively addressed all five characteristics
outlined in this paper were the most robust of all and could be used in
PCB manufacturing.
Abstract: This paper presents a semi-supervised learning algorithm called Iterative-Cross Training (ICT) to solve the Web pages classification problems. We apply Inductive logic programming (ILP) as a strong learner in ICT. The objective of this research is to evaluate the potential of the strong learner in order to boost the performance of the weak learner of ICT. We compare the result with the supervised Naive Bayes, which is the well-known algorithm for the text classification problem. The performance of our learning algorithm is also compare with other semi-supervised learning algorithms which are Co-Training and EM. The experimental results show that ICT algorithm outperforms those algorithms and the performance of the weak learner can be enhanced by ILP system.
Abstract: Geographic Information System (GIS) is a computerbased
tool used extensively to solve various engineering problems
related to spatial data. In spite of growing popularity of GIS, its
complete potential to construction industry has not been realized. In
this paper, the summary of up-to-date work on spatial applications of
GIS technologies in construction industry is presented. GIS
technologies have the potential to solve space related problems of
construction industry involving complex visualization, integration of
information, route planning, E-commerce, cost estimation, etc. GISbased
methodology to handle time and space issues of construction
projects scheduling is developed and discussed in this paper.
Abstract: With the advantage of wireless network technology,
there are a variety of mobile applications which make the issue of
wireless sensor networks as a popular research area in recent years.
As the wireless sensor network nodes move arbitrarily with the
topology fast change feature, mobile nodes are often confronted with
the void issue which will initiate packet losing, retransmitting,
rerouting, additional transmission cost and power consumption.
When transmitting packets, we would not predict void problem
occurring in advance. Thus, how to improve geographic routing with
void avoidance in wireless networks becomes an important issue. In
this paper, we proposed a greedy geographical void routing algorithm
to solve the void problem for wireless sensor networks. We use the
information of source node and void area to draw two tangents to
form a fan range of the existence void which can announce voidavoiding
message. Then we use source and destination nodes to draw
a line with an angle of the fan range to select the next forwarding
neighbor node for routing. In a dynamic wireless sensor network
environment, the proposed greedy void avoiding algorithm can be
more time-saving and more efficient to forward packets, and improve
current geographical void problem of wireless sensor networks.