Abstract: An experimental study of anaerobic treatment was performed by hybrid upflow anaerobic sludge blanket (HUASB) reactor to treat produced water (PW) of an onshore crude oil terminal (COD: 1597 mg/L, NH3-N: 14.7 mg/L, phenol: 13.8 mg/L, BOD5: 862 mg/L, sodium: 6240 mg/L and chloride 9530 mg/L). The produced water with high salinity and other toxic substances will inhibit the methanogens performance if there is no adaptation on biomass before anaerobic digestion. COD removal from produced water was investigated at five different dilutions of produced water and tap water (TW) without any nutrient addition and pre-treatment. The dilution ratios were 1PW:4TW, 2PW:3TW, 3PW:2TW, 4PW:1TW and 5PW:0TW. The reactor was evaluated at mesophilic operating condition (35 ± 2 °C) at 5 days of HRT for 250 days continuous feed. The average COD removals for 1PW:4TW, 2PW:3TW, 3PW:2TW, 4PW:1TW and 5PW:0TW were found to be approximately 76.1%, 73.8%, 70.3%, 46.3% and 61.82% respectively, with final average effluent COD of 123.7 mg/L, 240 mg/L, 294 mg/L, 589 mg/L and 738 mg/L, respectively.
Abstract: Arvia®, a spin-out company of University of Manchester, UK is commercialising a water treatment technology for the removal of low concentrations of organics from water. This technology is based on the adsorption of organics onto graphite based adsorbents coupled with their electrochemical regeneration in a simple electrochemical cell. In this paper, the potential of the process to adsorb microorganisms and electrochemically disinfect them present in water has been demonstrated. Bench scale experiments have indicated that the process of adsorption using graphite adsorbents with electrochemical regeneration can be used for water disinfection effectively. The most likely mechanisms of disinfection of water through this process include direct electrochemical oxidation and electrochemical chlorination.
Abstract: Nowadays, there is little information, concerning the
heat shield systems, and this information is not completely reliable to
use in so many cases. for example, the precise calculation cannot be
done for various materials. In addition, the real scale test has two
disadvantages: high cost and low flexibility, and for each case we
must perform a new test. Hence, using numerical modeling program
that calculates the surface recession rate and interior temperature
distribution is necessary. Also, numerical solution of governing
equation for non-charring material ablation is presented in order to
anticipate the recession rate and the heat response of non-charring
heat shields. the governing equation is nonlinear and the Newton-
Rafson method along with TDMA algorithm is used to solve this
nonlinear equation system. Using Newton- Rafson method for
solving the governing equation is one of the advantages of the
solving method because this method is simple and it can be easily
generalized to more difficult problems. The obtained results
compared with reliable sources in order to examine the accuracy of
compiling code.
Abstract: This paper describes the study of cryptographic hash functions, one of the most important classes of primitives used in recent techniques in cryptography. The main aim is the development of recent crypt analysis hash function. We present different approaches to defining security properties more formally and present basic attack on hash function. We recall Merkle-Damgard security properties of iterated hash function. The Main aim of this paper is the development of recent techniques applicable to crypt Analysis hash function, mainly from SHA family. Recent proposed attacks an MD5 & SHA motivate a new hash function design. It is designed not only to have higher security but also to be faster than SHA-256. The performance of the new hash function is at least 30% better than that of SHA-256 in software. And it is secure against any known cryptographic attacks on hash functions.
Abstract: The purpose of this study is to identify the critical success factors (CSFs) for the effective implementation of Six Sigma in non-formal service Sectors.
Based on the survey of literature, the critical success factors (CSFs) for Six Sigma have been identified and are assessed for their importance in Non-formal service sector using Delphi Technique. These selected CSFs were put forth to the panel of expert to cluster them and prepare cognitive map to establish their relationship.
All the critical success factors examined and obtained from the review of literature have been assessed for their importance with respect to their contribution to Six Sigma effectiveness in non formal service sector.
The study is limited to the non-formal service sectors involved in the organization of religious festival only. However, the similar exercise can be conducted for broader sample of other non-formal service sectors like temple/ashram management, religious tours management etc.
The research suggests an approach to identify CSFs of Six Sigma for Non-formal service sector. All the CSFs of the formal service sector will not be applicable to Non-formal services, hence opinion of experts was sought to add or delete the CSFs. In the first round of Delphi, the panel of experts has suggested, two new CSFs-“competitive benchmarking (F19) and resident’s involvement (F28)”, which were added for assessment in the next round of Delphi. One of the CSFs-“fulltime six sigma personnel (F15)” has been omitted in proposed clusters of CSFs for non-formal organization, as it is practically impossible to deploy full time trained Six Sigma recruits.
Abstract: Static synchronous compensator (STATCOM) is a shunt connected voltage source converter (VSC), which can affect rapid control of reactive flow in the transmission line by controlling the generated a.c. voltage. The main aim of the paper is to design a power system installed with a Static synchronous compensator (STATCOM) and demonstrates the application of the linearised Phillips-heffron model in analyzing the damping effect of the STATCOM to improve power system oscillation stability. The proposed PI controller is designed to coordinate two control inputs: Voltage of the injection bus and capacitor voltage of the STATCOM, to improve the Dynamic stability of a SMIB system .The power oscillations damping (POD) control and power system stabilizer (PSS) and their coordinated action with proposed controllers are tested. The simulation result shows that the proposed damping controllers provide satisfactory performance in terms of improvements of dynamic stability of the system.
Abstract: Cryptographic algorithms play a crucial role in the
information society by providing protection from unauthorized
access to sensitive data. It is clear that information technology will
become increasingly pervasive, Hence we can expect the emergence
of ubiquitous or pervasive computing, ambient intelligence. These
new environments and applications will present new security
challenges, and there is no doubt that cryptographic algorithms and
protocols will form a part of the solution. The efficiency of a public
key cryptosystem is mainly measured in computational overheads,
key size and bandwidth. In particular the RSA algorithm is used in
many applications for providing the security. Although the security
of RSA is beyond doubt, the evolution in computing power has
caused a growth in the necessary key length. The fact that most chips
on smart cards can-t process key extending 1024 bit shows that there
is need for alternative. NTRU is such an alternative and it is a
collection of mathematical algorithm based on manipulating lists of
very small integers and polynomials. This allows NTRU to high
speeds with the use of minimal computing power. NTRU (Nth degree
Truncated Polynomial Ring Unit) is the first secure public key
cryptosystem not based on factorization or discrete logarithm
problem. This means that given sufficient computational resources
and time, an adversary, should not be able to break the key. The
multi-party communication and requirement of optimal resource
utilization necessitated the need for the present day demand of
applications that need security enforcement technique .and can be
enhanced with high-end computing. This has promoted us to develop
high-performance NTRU schemes using approaches such as the use
of high-end computing hardware. Peer-to-peer (P2P) or enterprise
grids are proven as one of the approaches for developing high-end
computing systems. By utilizing them one can improve the
performance of NTRU through parallel execution. In this paper we
propose and develop an application for NTRU using enterprise grid
middleware called Alchemi. An analysis and comparison of its
performance for various text files is presented.
Abstract: This paper proposes a novel system for monitoring the
health of underground pipelines. Some of these pipelines transport
dangerous contents and any damage incurred might have catastrophic
consequences. However, most of these damage are unintentional and
usually a result of surrounding construction activities. In order to
prevent these potential damages, monitoring systems are
indispensable. This paper focuses on acoustically recognizing road
cutters since they prelude most construction activities in modern
cities. Acoustic recognition can be easily achieved by installing a
distributed computing sensor network along the pipelines and using
smart sensors to “listen" for potential threat; if there is a real threat,
raise some form of alarm. For efficient pipeline monitoring, a novel
monitoring approach is proposed. Principal Component Analysis
(PCA) was studied and applied. Eigenvalues were regarded as the
special signature that could characterize a sound sample, and were
thus used for the feature vector for sound recognition. The denoising
ability of PCA could make it robust to noise interference. One class
SVM was used for classifier. On-site experiment results show that the
proposed PCA and SVM based acoustic recognition system will be
very effective with a low tendency for raising false alarms.
Abstract: This paper describes the development of a control
system model using a graphical software tool. This control system is
part of an operator training simulator developed for the National
Training Center for Operators of Ixtapantongo (CNCAOI, acronym
according to its name in Spanish language) of the Mexico-s Federal
Commission of Electricity, CFE). The Department of Simulation of
the Electrical Research Institute (IIE) developed this simulator using
as reference the Unit I of the Combined Cycle Power Plant El Sauz,
located at the centre of Mexico. The first step in the project was the
developing of the Gas Turbine System and its control system
simulator. The Turbo Gas simulator was finished and delivered to
CNCAOI in March 2007 for commercial operation. This simulator is
a high-fidelity real time dynamic simulator built and tested for
accurate operation over the entire load range. The simulator was used
primarily for operator training although it has been used for
procedure development and evaluation of plant transients.
Abstract: This paper presented a new approach for centralized
monitoring and self-protected against fiber fault in fiber-to-the-home
(FTTH) access network by using Smart Access Network Testing,
Analyzing and Database (SANTAD). SANTAD will be installed
with optical line terminal (OLT) at central office (CO) for in-service
transmission surveillance and fiber fault localization within FTTH
with point-to-multipoint (P2MP) configuration downwardly from CO
towards customer residential locations based on the graphical user
interface (GUI) processing capabilities of MATLAB software.
SANTAD is able to detect any fiber fault as well as identify the
failure location in the network system. SANTAD enable the status of
each optical network unit (ONU) connected line is displayed onto
one screen with capability to configure the attenuation and detect the
failure simultaneously. The analysis results and information will be
delivered to the field engineer for promptly actions, meanwhile the
failure line will be diverted to protection line to ensure the traffic
flow continuously. This approach has a bright prospect to improve
the survivability and reliability as well as increase the efficiency and
monitoring capabilities in FTTH.
Abstract: A mathematical model for the hydrodynamic
lubrication of parabolic slider bearings with couple stress lubricants
is presented. A numerical solution for the mathematical model using
finite element scheme is obtained using three nodes isoparametric
quadratic elements. Stiffness integrals obtained from the weak form
of the governing equations were solved using Gauss Quadrature to
obtain a finite number of stiffness matrices. The global system of
equations was obtained for the bearing and solved using Gauss Seidel
iterative scheme. The converged pressure solution was used to obtain
the load capacity of the bearing. Parametric studies were carried out
and it was shown that the effect of couple stresses and profile
parameter are to increase the load carrying capacity of the parabolic
slider bearing. Numerical experiments reveal that the magnitude of
the profile parameter at which maximum load is obtained increases
with decrease in couple stress parameter. The results are presented in
graphical form.
Abstract: We presented results of research aimed on findings
influence of social - psychological training (realized with students of
Constantine the Philosopher University- future teachers within their
undergraduate preparation) on the choice of intrapersonal and
interpersonal features. After social- psychological training using
Interpersonal Check List (ICL) we found out shift of behavior to
more adaptive forms in categories, which are characterized by
extroversive friendly behavior, willingness to cooperation,
conformity regard to social situation, responsible and regardful
behavior.
Using State-Trait Anxiety Inventory (STAI) we found out the cut
down of state anxiety and of trait anxiety. The report was processed
within grants KEGA 3/5269/07 and VEGA 1/3675/06.
Abstract: The data is available in abundance in any business
organization. It includes the records for finance, maintenance,
inventory, progress reports etc. As the time progresses, the data keep
on accumulating and the challenge is to extract the information from
this data bank. Knowledge discovery from these large and complex
databases is the key problem of this era. Data mining and machine
learning techniques are needed which can scale to the size of the
problems and can be customized to the application of business. For
the development of accurate and required information for particular
problem, business analyst needs to develop multidimensional models
which give the reliable information so that they can take right
decision for particular problem. If the multidimensional model does
not possess the advance features, the accuracy cannot be expected.
The present work involves the development of a Multidimensional
data model incorporating advance features. The criterion of
computation is based on the data precision and to include slowly
change time dimension. The final results are displayed in graphical
form.
Abstract: Studies regarding the determination of population
trend of Lipaphis erysimi (kalt.) and its associated natural enemies in
different Brassica lines along with the effect of gamma radiation on
their population were conducted at Agricultural Research Farm,
Malakandher, Khyber Pakhtunkhwa Agricultural University
Peshawar during spring 2006. Three different Brassica lines F6B3,
F6B6 and F6B7 were used, which were replicated four times in
Randomized Complete Block Design. The data revealed that aphid
infestation invariably stated in all three varieties during last week of
February 2006 (1st observation). The peak population of 4.39 aphids
leaf-1 was s recorded during 2nd week of March and lowest population
of 1.02 aphids leaf-1 was recorded during 5th week of March. The
species of lady bird beetle (Coccinella septempunctata) and Syrphid
fly (Syrphus balteatus) first appeared on 24th February with a mean
number of 0.40 lady bird beetle leaf-1 and 0.87 Syrphid fly leaf-1,
respectively. At the time when aphid population started to increase
the peak population of C. septempunctata (0.70 lady bird beetle leaf-
1) and S. balteatus (1.04 syrphid fly leaf-1) was recorded on the 2nd
week of March. Chrysoperla carnea appeared in the 1st week of
March and their peak population was recorded during the 3rd week of
March with mean population of 1.46 C. carnea leaf-1. Among all the
Brassica lines, F6B7 showed comparatively more resistance as
compared to F6B3 F6B6. F6B3 showed least resistance against L.
erysimi, which was found to be the most susceptible cultivar. F6B7
was also found superior in terms of natural enemies. Maximum
number of all natural enemies was recorded on this variety followed
by F6B6. Lowest number of natural enemies was recorded in F6B3.
No significant effect was recorded for the effect of gamma radiation
on the population of aphids, natural enemies and on the varieties.
Abstract: The present contribution deals with the
thermophoretic deposition of nanoparticles over a rapidly rotating
permeable disk in the presence of partial slip, magnetic field, thermal
radiation, thermal-diffusion, and diffusion-thermo effects. The
governing nonlinear partial differential equations such as continuity,
momentum, energy and concentration are transformed into nonlinear
ordinary differential equations using similarity analysis, and the
solutions are obtained through the very efficient computer algebra
software MATLAB. Graphical results for non-dimensional
concentration and temperature profiles including thermophoretic
deposition velocity and Stanton number (thermophoretic deposition
flux) in tabular forms are presented for a range of values of the
parameters characterizing the flow field. It is observed that slip
mechanism, thermal-diffusion, diffusion-thermo, magnetic field and
radiation significantly control the thermophoretic particles deposition
rate. The obtained results may be useful to many industrial and
engineering applications.
Abstract: In high powered dense wavelength division
multiplexed (WDM) systems with low chromatic dispersion,
four-wave mixing (FWM) can prove to be a major source of noise.
The MultiCanonical Monte Carlo Method (MCMC) and the Split
Step Fourier Method (SSFM) are combined to accurately evaluate the
probability density function of the decision variable of a receiver,
limited by FWM. The combination of the two methods leads to more
accurate results, and offers the possibility of adding other optical
noises such as the Amplified Spontaneous Emission (ASE) noise.
Abstract: We report a lithography-free approach to fabricate the
biomimetics, quasi-beehive Si nanostructures (QBSNs), on
Si-substrates. The self-assembled SiGe nanoislands via the strain
induced surface roughening (Asaro-Tiller-Grinfeld instability) during
in-situ annealing play a key role as patterned sacrifice regions for
subsequent reactive ion etching (RIE) process performed for
fabricating quasi-beehive nanostructures on Si-substrates. As the
measurements of field emission, the bare QBSNs show poor field
emission performance, resulted from the existence of the native oxide
layer which forms an insurmountable barrier for electron emission. In
order to dramatically improve the field emission characteristics, the
platinum nanopillars (Pt-NPs) were deposited on QBSNs to form
Pt-NPs/QBSNs heterostructures. The turn-on field of Pt-NPs/QBSNs
is as low as 2.29 V/μm (corresponding current density of 1 μA/cm2),
and the field enhancement factor (β-value) is significantly increased to
6067. More importantly, the uniform and continuous electrons excite
light emission, due to the surrounding filed emitters from
Pt-NPs/QBSNs, can be easily obtained. This approach does not require
an expensive photolithographic process and possesses great potential
for applications.
Abstract: The concentrations of As, Hg, Co, Cr and Cd were
tested for each soil sample, and their spatial patterns were analyzed
by the semivariogram approach of geostatistics and geographical
information system technology. Multivariate statistic approaches
(principal component analysis and cluster analysis) were used to
identify heavy metal sources and their spatial pattern. Principal
component analysis coupled with correlation between heavy metals
showed that primary inputs of As, Hg and Cd were due to
anthropogenic while, Co, and Cr were associated with pedogenic
factors. Ordinary kriging was carried out to map the spatial patters of
heavy metals. The high pollution sources evaluated was related with
usage of urban and industrial wastewater. The results of this study
helpful for risk assessment of environmental pollution for decision
making for industrial adjustment and remedy soil pollution.
Abstract: Natural gas flow contains undesirable solid particles,
liquid condensation, and/or oil droplets and requires reliable
removing equipment to perform filtration. Recent natural gas
processing applications are demanded compactness and reliability of
process equipment. Since conventional means are sophisticated in
design, poor in efficiency, and continue lacking robust, a supersonic
nozzle has been introduced as an alternative means to meet such
demands.
A 3-D Convergent-Divergent Nozzle is simulated using
commercial Code for pressure ratio (NPR) varies from 1.2 to 2. Six
different shapes of nozzle are numerically examined to illustrate the
position of shock-wave as such spot could be considered as a
benchmark of particle separation. Rectangle, triangle, circular,
elliptical, pentagon, and hexagon nozzles are simulated using Fluent
Code with all have same cross-sectional area.
The simple one-dimensional inviscid theory does not describe the
actual features of fluid flow precisely as it ignores the impact of
nozzle configuration on the flow properties. CFD Simulation results,
however, show that nozzle geometry influences the flow structures
including location of shock wave.
The CFD analysis predicts shock appearance when p01/pa>1.2 for
almost all geometry and locates at the lower area ratio (Ae/At).
Simulation results showed that shock wave in Elliptical nozzle has
the farthest distance from the throat among the others at relatively
small NPR. As NPR increases, hexagon would be the farthest. The
numerical result is compared with available experimental data and
has shown good agreement in terms of shock location and flow
structure.
Abstract: In order to implement flexibility as well as survivable
capacities over passive optical network (PON), a new automatic
random fault-recovery mechanism with array-waveguide-grating
based (AWG-based) optical switch (OSW) is presented. Firstly,
wavelength-division-multiplexing and optical code-division
multiple-access (WDM/OCDMA) scheme are configured to meet the
various geographical locations requirement between optical network
unit (ONU) and optical line terminal (OLT). The AWG-base optical
switch is designed and viewed as central star-mesh topology to
prohibit/decrease the duplicated redundant elements such as fiber and
transceiver as well. Hence, by simple monitoring and routing switch
algorithm, random fault-recovery capacity is achieved over
bi-directional (up/downstream) WDM/OCDMA scheme. When error
of distribution fiber (DF) takes place or bit-error-rate (BER) is higher
than 10-9 requirement, the primary/slave AWG-based OSW are
adjusted and controlled dynamically to restore the affected ONU
groups via the other working DFs immediately.