Abstract: Space Vector Modulation (SVM) is an optimum Pulse Width Modulation (PWM) technique for an inverter used in a variable frequency drive applications. It is computationally rigorous and hence limits the inverter switching frequency. Increase in switching frequency can be achieved using Neural Network (NN) based SVM, implemented on application specific chips. This paper proposes a neural network based SVM technique for a Voltage Source Inverter (VSI). The network proposed is independent of switching frequency. Different architectures are investigated keeping the total number of neurons constant. The performance of the inverter is compared for various switching frequencies for different architectures of NN based SVM. From the results obtained, the network with minimum resource and appropriate word length is identified. The bit precision required for this application is identified. The network with 8-bit precision is implemented in the IC XCV 400 and the results are presented. The performance of NN based general purpose SVM with higher bit precision is discussed.
Abstract: This paper presents the design, implementation and
results related to the storage system of medical information
associated to the ECG (Electrocardiography) signal. The system
includes the signal acquisition modules, the preprocessing and signal
processing, followed by a module of transmission and reception of
the signal, along with the storage and web display system of the
medical platform. The tests were initially performed with this signal,
with the purpose to include more biosignal under the same system in
the future.
Abstract: This paper describes the design considerations of an
experimental setup for research and exploring the drives of batteryfed
electric vehicles. Effective setup composition and its components
are discussed. With experimental setup described in this paper,
durability and functional tests can be procured to the customers.
Multiple experiments are performed in the form of steady-state
system exploring, acceleration programs, multi-step tests (speed
control, torque control), load collectives or close-to-reality driving
tests (driving simulation). Main focus of the functional testing is on
the measurements of power and energy efficiency and investigations
in driving simulation mode, which are used for application purposes.
In order to enable the examination of the drive trains beyond
standard modes of operation, different other parameters can be
studied also.
Abstract: The development of One Tambon One Product
(OTOP) became the policy of the government in 1997 after the
former Prime Minister had been in power. The strategy of sections is
currently set for the policy. OTOP has become the part of the way of
community lives around the country. OTOP may be developed under
changing into ASEAN economic community in 2015 because of the
flow of capitals, productions, and many workers in the region. All
sectors are improved for the change. The purposes of study were to
study the strength and weakness of the OTOP-creating process via its
policy and to lead to the strategy to be able to apply before changing.
The methodology is qualitative to study its policy including
document and to interview experienced persons. The findings showed
that the effort of improvement of all sectors obviously involves with
OTOP development. Particularly, the strategic administration of
OTOP is in every level of the state, central sector, region, and
community.
Abstract: This paper describes a steady state model of a multiple
effect evaporator system for simulation and control purposes. The
model includes overall as well as component mass balance equations,
energy balance equations and heat transfer rate equations for area
calculations for all the effects. Each effect in the process is
represented by a number of variables which are related by the energy
and material balance equations for the feed, product and vapor flow
for backward, mixed and split feed. For simulation 'fsolve' solver in
MATLAB source code is used. The optimality of three sequences i.e.
backward, mixed and splitting feed is studied by varying the various
input parameters.
Abstract: The mixture formation prior to the ignition process
plays as a key element in the diesel combustion. Parametric studies of
mixture formation and ignition process in various injection parameter
has received considerable attention in potential for reducing
emissions. Purpose of this study is to clarify the effects of injection
pressure on mixture formation and ignition especially during ignition
delay period, which have to be significantly influences throughout the
combustion process and exhaust emissions. This study investigated
the effects of injection pressure on diesel combustion fundamentally
using rapid compression machine. The detail behavior of mixture
formation during ignition delay period was investigated using the
schlieren photography system with a high speed camera. This method
can capture spray evaporation, spray interference, mixture formation
and flame development clearly with real images. Ignition process and
flame development were investigated by direct photography method
using a light sensitive high-speed color digital video camera. The
injection pressure and air motion are important variable that strongly
affect to the fuel evaporation, endothermic and prolysis process
during ignition delay. An increased injection pressure makes spray tip
penetration longer and promotes a greater amount of fuel-air mixing
occurs during ignition delay. A greater quantity of fuel prepared
during ignition delay period thus predominantly promotes more rapid
heat release.
Abstract: The purpose of this article is to briefly review the opportunities that social media present to counselors and psychologists. Particular attention was given to understanding some of the more important common risks inherent in social media and the potential ethical dilemmas which may arise for counselors and psychologists who embrace them in their practice. Key considerations of issues pertinent to an online presence such as multiple relationships, visibility and privacy, maintaining ethical principles and professional boundaries are being discussed.
Abstract: The reliability of the tools developed to learn the
learning styles is essential to find out students- learning styles
trustworthily. For this purpose, the psychometric features of Grasha-
Riechman Student Learning Style Inventory developed by Grasha
was studied to contribute to this field. The study was carried out on
6th, 7th, and 8th graders of 10 primary education schools in Konya.
The inventory was applied twice with an interval of one month, and
according to the data of this application, the reliability coefficient
numbers of the 6 sub-dimensions pointed in the theory of the
inventory was found to be medium. Besides, it was found that the
inventory does not have a structure with 6 factors for both
Mathematics and English courses as represented in the theory.
Abstract: End milling process is one of the common metal
cutting operations used for machining parts in manufacturing
industry. It is usually performed at the final stage in manufacturing a
product and surface roughness of the produced job plays an
important role. In general, the surface roughness affects wear
resistance, ductility, tensile, fatigue strength, etc., for machined parts
and cannot be neglected in design. In the present work an
experimental investigation of end milling of aluminium alloy with
carbide tool is carried out and the effect of different cutting
parameters on the response are studied with three-dimensional
surface plots. An artificial neural network (ANN) is used to establish
the relationship between the surface roughness and the input cutting
parameters (i.e., spindle speed, feed, and depth of cut). The Matlab
ANN toolbox works on feed forward back propagation algorithm is
used for modeling purpose. 3-12-1 network structure having
minimum average prediction error found as best network architecture
for predicting surface roughness value. The network predicts surface
roughness for unseen data and found that the result/prediction is
better. For desired surface finish of the component to be produced
there are many different combination of cutting parameters are
available. The optimum cutting parameter for obtaining desired
surface finish, to maximize tool life is predicted. The methodology is
demonstrated, number of problems are solved and algorithm is coded
in Matlab®.
Abstract: Static Var Compensator (SVC) is a shunt type FACTS
device which is used in power system primarily for the purpose of
voltage and reactive power control. In this paper, a fuzzy logic based
supplementary controller for Static Var Compensator (SVC) is
developed which is used for damping the rotor angle oscillations and
to improve the transient stability of the power system. Generator
speed and the electrical power are chosen as input signals for the
Fuzzy Logic Controller (FLC). The effectiveness and feasibility of
the proposed control is demonstrated with Single Machine Infinite
Bus (SMIB) system and multimachine system (WSCC System)
which show improvement over the use of a fixed parameter
controller.
Abstract: Access to information is the key to the empowerment of everybody despite where they are living. This research is to be carried out in respect of the people living in developing countries, considering their plight and complex geographical, demographic, social-economic conditions surrounding the areas they live, which hinder access to information and of professionals providing services such as medical workers, which has led to high death rates and development stagnation. Research on Unified Communications and Integrated Collaborations (UCIC) system in the health sector of developing countries comes in to create a possible solution of bridging the digital canyon among the communities. The aim is to deliver services in a seamless manner to assist health workers situated anywhere to be accessed easily and access information which will help in service delivery. The proposed UCIC provides the most immersive Telepresence experience for one-to-one or many-tomany meetings. Extending to locations anywhere in the world, the transformative platform delivers Ultra-low operating costs through the use of general purpose networks and using special lenses and track systems.
Abstract: The measurement of aerodynamic forces and moments
acting on an aircraft model is important for the development of wind
tunnel measurement technology to predict the performance of the full
scale vehicle. The potentials of an aircraft model with and without
winglet and aerodynamic characteristics with NACA wing No. 65-3-
218 have been studied using subsonic wind tunnel of 1 m × 1 m
rectangular test section and 2.5 m long of Aerodynamics Laboratory
Faculty of Engineering (University Putra Malaysia). Focusing on
analyzing the aerodynamic characteristics of the aircraft model, two
main issues are studied in this paper. First, a six component wind
tunnel external balance is used for measuring lift, drag and pitching
moment. Secondly, Tests are conducted on the aircraft model with
and without winglet of two configurations at Reynolds numbers
1.7×105, 2.1×105, and 2.5×105 for different angle of attacks. Fuzzy
logic approach is found as efficient for the representation,
manipulation and utilization of aerodynamic characteristics.
Therefore, the primary purpose of this work was to investigate the
relationship between lift and drag coefficients, with free-stream
velocities and angle of attacks, and to illustrate how fuzzy logic
might play an important role in study of lift aerodynamic
characteristics of an aircraft model with the addition of certain
winglet configurations. Results of the developed fuzzy logic were
compared with the experimental results. For lift coefficient analysis,
the mean of actual and predicted values were 0.62 and 0.60
respectively. The coreelation between actual and predicted values
(from FLS model) of lift coefficient in different angle of attack was
found as 0.99. The mean relative error of actual and predicted valus
was found as 5.18% for the velocity of 26.36 m/s which was found to
be less than the acceptable limits (10%). The goodness of fit of
prediction value was 0.95 which was close to 1.0.
Abstract: Gold coated silica core nanoparticles have an optical
response dictated by the plasmon resonance. The wavelength at
which the resonance occurs depends on the core and shell sizes,
allowing nanoshells to be tailored for particular applications. The
purposes of this study was to synthesize and use different
concentration of gold nanoshells as exogenous material for skin
tissue soldering and also to examine the effect of laser soldering
parameters on the properties of repaired skin. Two mixtures of
albumin solder and different concentration of gold nanoshells were
prepared. A full thickness incision of 2×20 mm2 was made on the
surface and after addition of mixtures it was irradiated by an 810nm
diode laser at different power densities. The changes of tensile
strength σt due to temperature rise, number of scan (Ns), and scan
velocity (Vs) were investigated. The results showed at constant laser
power density (I), σt of repaired incisions increases by increasing the
concentration of gold nanoshells, Ns and decreasing Vs. It is therefore
important to consider the trade off between the scan velocity and the
surface temperature for achieving an optimum operating condition. In
our case this corresponds to σt =1610 gr/cm2 at I~ 60 Wcm-2, T ~
65ºC, Ns =10 and Vs=0.2mms-1.
Abstract: Many applications require surface modification and
micro-structuring of polymers. For these purposes is mainly used
ultraviolet (UV) radiation from excimer lamps or excimer lasers.
However, these sources have a decided disadvantage - degrading the
polymer deep inside due to relatively big radiation penetration depth
which may exceed 100 μm. In contrast, extreme ultraviolet (EUV)
radiation is absorbed in a layer approximately 100 nm thick only. In
this work, the radiation from a discharge-plasma EUV source (with
wavelength 46.9 nm) based on a capillary discharge driver is focused
with a spherical Si/Sc multilayer mirror for surface modification of
PMMA sample or thin gold layer (thickness about 40 nm). It was
found that the focused EUV laser beam is capable by one shot to
ablate PMMA or layer of gold, even if the focus is significantly
influenced by astigmatism.
Abstract: The storage of chemical fertilizers in concrete building often leads to durability problems due to chemical attack. The damage of concrete is mostly caused by certain ammonium salts. The main purpose of the research is to investigate the durability properties of concrete being exposed to ammonium nitrate solution. In this investigation, experiments are conducted on concrete type G50 and G60. The leaching process is achieved by the use of 20% concentration solution of ammonium nitrate. The durability properties investigated are water absorption, volume of permeable voids, and sorptivity. Compressive strength, pH value, and degradation depth are measured after a certain period of leaching. A decrease in compressive strength and an increase in porosity are found through the conducted experiments. Apart from that, the experimental data shows that pH value decreases with increased leaching time while the degradation depth of concrete increases with leaching time. By comparing concrete type G50 and G60, concrete type G60 is more resistant to ammonium nitrate attack.
Abstract: Many studies have focused on the nonlinear analysis
of electroencephalography (EEG) mainly for the characterization of
epileptic brain states. It is assumed that at least two states of the
epileptic brain are possible: the interictal state characterized by a
normal apparently random, steady-state EEG ongoing activity; and
the ictal state that is characterized by paroxysmal occurrence of
synchronous oscillations and is generally called in neurology, a
seizure.
The spatial and temporal dynamics of the epileptogenic process is
still not clear completely especially the most challenging aspects of
epileptology which is the anticipation of the seizure. Despite all the
efforts we still don-t know how and when and why the seizure
occurs. However actual studies bring strong evidence that the
interictal-ictal state transition is not an abrupt phenomena. Findings
also indicate that it is possible to detect a preseizure phase.
Our approach is to use the neural network tool to detect interictal
states and to predict from those states the upcoming seizure ( ictal
state). Analysis of the EEG signal based on neural networks is used
for the classification of EEG as either seizure or non-seizure. By
applying prediction methods it will be possible to predict the
upcoming seizure from non-seizure EEG.
We will study the patients admitted to the epilepsy monitoring
unit for the purpose of recording their seizures. Preictal, ictal, and
post ictal EEG recordings are available on such patients for analysis
The system will be induced by taking a body of samples then
validate it using another. Distinct from the two first ones a third body
of samples is taken to test the network for the achievement of
optimum prediction. Several methods will be tried 'Backpropagation
ANN' and 'RBF'.
Abstract: Till date, English as a Second Language (ESL) educators involved in teaching language and communication to engineering students face an uphill task in developing graduate communicative competency. This challenge is accentuated by the apparent lack of English for Specific Purposes (ESP) materials for engineering students in the engineering curriculum. As such, most ESL educators are forced to play multiple roles. They don tasks such as curriculum designers, material writers and teachers with limited knowledge of the disciplinary content. Previous research indicates that prospective professional engineers should possess some sub-sets of competency: technical, linguistic oral immediacy, meta-cognitive and rhetorical explanatory competence. Another study revealed that engineering students need to be equipped with technical and linguistic oral immediacy competence. However, little is known whether these competency needs are in line with the educators- perceptions of communicative competence. This paper examines the best mix of communicative competence subsets that create the magic for engineering students in technical oral presentations. For the purpose of this study, two groups of educators were interviewed. These educators were language and communication lecturers involved in teaching a speaking course and content experts who assess students- technical oral presentations at tertiary level. The findings indicate that these two groups differ in their perceptions
Abstract: In this paper, a new learning approach for network
intrusion detection using naïve Bayesian classifier and ID3 algorithm
is presented, which identifies effective attributes from the training
dataset, calculates the conditional probabilities for the best attribute
values, and then correctly classifies all the examples of training and
testing dataset. Most of the current intrusion detection datasets are
dynamic, complex and contain large number of attributes. Some of
the attributes may be redundant or contribute little for detection
making. It has been successfully tested that significant attribute
selection is important to design a real world intrusion detection
systems (IDS). The purpose of this study is to identify effective
attributes from the training dataset to build a classifier for network
intrusion detection using data mining algorithms. The experimental
results on KDD99 benchmark intrusion detection dataset demonstrate
that this new approach achieves high classification rates and reduce
false positives using limited computational resources.
Abstract: This paper presents the results of the authors in designing, experimenting, assessing and transferring an innovative approach to energy education in secondary schools, aimed to enhance the quality of learning in terms of didactic curricula and pedagogic methods. The training is online delivered to youngsters via e-Books and portals specially designed for this purpose or by learning by doing via interactive games. An online educational methodology is available teachers.
Abstract: In this study, to compress ECG signals, KLT (Karhunen-
Loeve Transform) method has been used. The purpose of this method is to
perform effective ECG coding by a correlation between the length of frames
and the number of vectors of ECG signals.