Abstract: This paper deals with new concept of using compressed atmospheric air as a zero pollution power source for running motorbikes. The motorbike is equipped with an air turbine in place of an internal combustion engine, and transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor to casing diameter ratios with respect to different vane angles (number of vanes) have been considered and analyzed. It is found that the shaft work output is optimum for some typical values of rotor / casing diameter ratios at a particular value of vane angle (no. of vanes). In this study, the maximum power is obtained as 4.5kW - 5.3kW (5.5-6.25 HP) when casing diameter is taken 100 mm, and rotor to casing diameter ratios are kept from 0.65 to 0.55. This value of output is sufficient to run motorbike.
Abstract: This research project is developed in order to study
managerial styles of modern Thai executives. The thorough
understanding will lead to continuous improvement and efficient
performance of Thai business organizations. Regarding managerial
skills, Thai executives focus heavily upon human skills. Also, the
negotiator roles are most emphasis in their management. In addition,
Thai executives pay most attention to the fundamental management
principles including Harmony and Unity of Direction of the
organizations. Moreover, the management techniques, consisting of
Team work and Career Planning are of their main concern. Finally,
Thai executives wish to enhance their firms- image and employees-
morale through conducting the ethical and socially responsible
activities. The major tactic deployed to stimulate employees- ethical
behaviors and mindset is Code of Ethics development.
Abstract: This paper focuses on robust design and optimization
of industrial production wastes. Past literatures were reviewed to case
study Clamason Industries Limited (CIL) - a leading ladder-tops
manufacturer. A painstaking study of the firm-s practices at the shop
floor revealed that Over-production, Waiting time, Excess inventory,
and Defects are the major wastes that are impeding their progress and
profitability. Design expert8 software was used to apply Taguchi
robust design and response surface methodology in order to model,
analyse and optimise the wastes cost in CIL. Waiting time and overproduction
rank first and second in contributing to the costs of wastes
in CIL. For minimal wastes cost the control factors of overproduction,
waiting-time, defects and excess-inventory must be set at
0.30, 390.70, 4 and 55.70 respectively for CIL. The optimal value of
cost of wastes for the months studied was 22.3679. Finally, a
recommendation was made that for the company to enhance their
profitability and customer satisfaction, they must adopt the Shingeo
Shingo-s Single Minute Exchange of Dies (SMED), which will
immediately tackle the waste of waiting by drastically reducing their
setup time.
Abstract: The indistinctness of the manufacturing processes makes that a parts cannot be realized in an absolutely exact way towards the specifications on the dimensions. It is thus necessary to assume that the effectively realized product has to belong in a very strict way to compatible intervals with a correct functioning of the parts. In this paper we present an approach based on mixing tow different characteristics theories, the fuzzy system and Petri net system. This tool has been proposed to model and control the quality in an assembly system. A robust command of a mechanical assembly process is presented as an application. This command will then have to maintain the specifications interval of parts in front of the variations. It also illustrates how the technique reacts when the product quality is high, medium, or low.
Abstract: The interline power flow controller (IPFC) is one of
the latest generation flexible AC transmission systems (FACTS)
controller used to control power flows of multiple transmission lines.
This paper presents a mathematical model of IPFC, termed as power
injection model (PIM). This model is incorporated in Newton-
Raphson (NR) power flow algorithm to study the power flow control
in transmission lines in which IPFC is placed. A program in
MATLAB has been written in order to extend conventional NR
algorithm based on this model. Numerical results are carried out on a
standard 2 machine 5 bus system. The results without and with IPFC
are compared in terms of voltages, active and reactive power flows to
demonstrate the performance of the IPFC model.
Abstract: To solve the problem of multisensor data fusion under
non-Gaussian channel noise. The advanced M-estimates are known
to be robust solution while trading off some accuracy. In order to
improve the estimation accuracy while still maintaining the equivalent
robustness, a two-stage robust fusion algorithm is proposed using
preliminary rejection of outliers then an optimal linear fusion. The
numerical experiments show that the proposed algorithm is equivalent
to the M-estimates in the case of uncorrelated local estimates and
significantly outperforms the M-estimates when local estimates are
correlated.
Abstract: In this paper, a novel LVTSCR-based device for
electrostatic discharge (ESD) protection of integrated circuits (ICs) is
designed, fabricated and characterized. The proposed device is similar
to the conventional LVTSCR but it has an embedded PMOSFET in the
anode n-well to enhance the turn on speed, the clamping capability and
the robustness. This is possible because the embedded PMOSFET
provides the sub-path of ESD discharge current. The TLP, HBM and
MM testing are carried out to verify the ESD performance of the
proposed devices, which are fabricated in 0.35um
(Bipolar-CMOS-DMOS) BCDMOS process. The device has the
robustness of 70mA/um that is higher about 60mA/um than the
LVTSCR, approximately.
Abstract: In this paper a novel scheme for watermarking digital
audio during its compression to MPEG-1 Layer III format is
proposed. For this purpose we slightly modify some of the selected
MDCT coefficients, which are used during MPEG audio
compression procedure. Due to the possibility of modifying different
MDCT coefficients, there will be different choices for embedding the
watermark into audio data, considering robustness and transparency
factors. Our proposed method uses a genetic algorithm to select the
best coefficients to embed the watermark. This genetic selection is
done according to the parameters that are extracted from the
perceptual content of the audio to optimize the robustness and
transparency of the watermark. On the other hand the watermark
security is increased due to the random nature of the genetic
selection. The information of the selected MDCT coefficients that
carry the watermark bits, are saves in a database for future extraction
of the watermark. The proposed method is suitable for online MP3
stores to pursue illegal copies of musical artworks. Experimental
results show that the detection ratio of the watermarks at the bitrate
of 128kbps remains above 90% while the inaudibility of the
watermark is preserved.
Abstract: Fly ash is one of the residues generated in
combustion, and comprises the fine particles that rise with the flue
gases. Ash which does not rise is termed bottom ash [1]. In our
country, it is expected that will be occurred 50 million tons of waste
ash per year until 2020. Released waste from the thermal power
plants is caused very significant problems as known. The fly ashes
can be evaluated by using as adsorbent material.
The purpose of this study is to investigate the possibility of use of
Tuncbilek fly ash like low-cost adsorbents for heavy metal
adsorption. First of all, Tuncbilek fly ash was characterized. For this
purpose; analysis such as sieve analysis, XRD, XRF, SEM and FT-IR
were performed.
Abstract: This paper presents the application of a signal
intensity independent registration criterion for 2D rigid body
registration of medical images using 1D binary projections. The
criterion is defined as the weighted ratio of two projections. The ratio
is computed on a pixel per pixel basis and weighting is performed by
setting the ratios between one and zero pixels to a standard high
value. The mean squared value of the weighted ratio is computed
over the union of the one areas of the two projections and it is
minimized using the Chebyshev polynomial approximation using
n=5 points. The sum of x and y projections is used for translational
adjustment and a 45deg projection for rotational adjustment. 20 T1-
T2 registration experiments were performed and gave mean errors
1.19deg and 1.78 pixels. The method is suitable for contour/surface
matching. Further research is necessary to determine the robustness
of the method with regards to threshold, shape and missing data.
Abstract: Ranong province has the best kaolin, and it is the most
useful of all the clay types used in ceramic making. Until recently,
there has been only one community business making ceramics in
Ranong province. And this business could not build the mix of body
and glaze from their raw material without assistance. Considering
these problems, this research is aimed to test the composition of
ceramic body and glaze which suit. Kaolin from Ranong is the raw
material which these search focuses on. All other raw materials use in
the investigation will come from southern Thailand, kaolin and
limestone from Ranong province, ball clay from Surat Thani
province, white sand from Songkhla province, and feldspar from
Nakhon Si Thammarat province. Results can be used to develop the
efficiency of industrial production which in return will enhance the
business process.
Abstract: In this paper the performance of unified power flow
controller is investigated in controlling the flow of po wer over the
transmission line. Voltage sources model is utilized to study the
behaviour of the UPFC in regulating the active, reactive power and
voltage profile. This model is incorporated in Newton Raphson
algorithm for load flow studies. Simultaneous method is employed
in which equations of UPFC and the power balance equations of
network are combined in to one set of non-linear algebraic equations.
It is solved according to the Newton raphson algorithm. Case studies
are carried on standard 5 bus network. Simulation is done in Matlab.
The result of network with and without using UPFC are compared in
terms of active and reactive power flows in the line and active and
reactive power flows at the bus to analyze the performance of UPFC.
Abstract: System testing is actually done to the entire system
against the Functional Requirement Specification and/or the System
Requirement Specification. Moreover, it is an investigatory testing
phase, where the focus is to have almost a destructive attitude and
test not only the design, but also the behavior and even the believed
expectations of the customer. It is also intended to test up to and
beyond the bounds defined in the software/hardware requirements
specifications. In Motorola®, Automated Testing is one of the testing
methodologies uses by GSG-iSGT (Global Software Group - iDEN
TM
Subcriber Group-Test) to increase the testing volume, productivity
and reduce test cycle-time in iDEN
TM
phones testing. Testing is able
to produce more robust products before release to the market. In this
paper, iHopper is proposed as a tool to perform stress test on iDEN
TM
phonse. We will discuss the value that automation has brought to
iDEN
TM
Phone testing such as improving software quality in the
iDEN
TM
phone together with some metrics. We will also look into
the advantages of the proposed system and some discussion of the
future work as well.
Abstract: The quality of Ribbed Smoked Sheets
(RSS) primarily based on color, dryness, and the presence or
absence of fungus and bubbles. This quality is strongly
influenced by the drying and fumigation process namely
smoking process. Smoking that is held in high temperature
long time will result scorched dark brown sheets, whereas if
the temperature is too low or slow drying rate would resulted
in less mature sheets and growth of fungus. Therefore need to
find the time and temperature for optimum quality of sheets.
Enhance, unmonitored heat and mass transfer during smoking
process lead to high losses of energy balance. This research
aims to generate simple empirical mathematical model
describing the effect of smoking time and temperature to RSS
quality of color, water content, fungus and bubbles. The
second goal of study was to analyze energy balance during
smoking process. Experimental study was conducted by
measuring temperature, residence time and quality parameters
of 16 sheets sample in smoking rooms. Data for energy
consumption balance such as mass of fuel wood, mass of
sheets being smoked, construction temperature, ambient
temperature and relative humidity were taken directly along
the smoking process. It was found that mathematical model
correlating smoking temperature and time with color is Color
= -169 - 0.184 T4 - 0.193 T3 - 0.160 0.405 T1 + T2 + 0.388 t1
+3.11 t2 + 3.92t3 + 0.215 t4 with R square 50.8% and with
moisture is Moisture = -1.40-0.00123 T4 + 0.00032 T3 +
0.00260 T2 - 0.00292 T1 - 0.0105 t1 + 0.0290 t2 + 0.0452 t3
+ 0.00061 t4 with R square of 49.9%. Smoking room energy
analysis found useful energy was 27.8%. The energy stored in
the material construction 7.3%. Lost of energy in conversion
of wood combustion, ventilation and others were 16.6%. The
energy flowed out through the contact of material construction
with the ambient air was found to be the highest contribution
to energy losses, it reached 48.3%.
Abstract: The main aim of Supply Chain Management (SCM) is
to produce, distribute, logistics and deliver goods and equipment in
right location, right time, right amount to satisfy costumers, with
minimum time and cost waste. So implementing techniques that
reduce project time and cost, and improve productivity and
performance is very important. Emerging technologies such as the
Radio Frequency Identification (RFID) are now making it possible to
automate supply chains in a real time manner and making them more
efficient than the simple supply chain of the past for tracing and
monitoring goods and products and capturing data on movements of
goods and other events. This paper considers concepts, components
and RFID technology characteristics by concentration of warehouse
and inventories management. Additionally, utilization of RFID in the
role of improving information management in supply chain is
discussed. Finally, the facts of installation and this technology-s
results in direction with warehouse and inventory management and
business development will be presented.
Abstract: Nowadays, under developed countries for progress in
science and technology and decreasing the technologic gap with
developed countries, increasing the capacities and technology
transfer from developed countries. To remain competitive, industry is
continually searching for new methods to evolve their products.
Business model is one of the latest buzzwords in the Internet and
electronic business world. To be successful, organizations must look
into the needs and wants of their customers. This research attempts to
identify a specific feature of the company with a strong competitive
advantage by analyzing the cause of Customer satisfaction. Due to
the rapid development of knowledge and information technology,
business environments have become much more complicated.
Information technology can help a firm aiming to gain a competitive
advantage. This study explores the role and effect of Information
Communication Technology in Business Models and Customer
satisfaction on firms and also relationships between ICTs and
Outsourcing strategic.
Abstract: The aim of the study was to follow changes of powervelocity
relationship in female volleyball players during an annual
training cycle. The study was conducted on eleven female volleyball
players: age 21.6±1.7 years, body height 177.9±4.7 cm, body mass
71.3±6.6 kg and training experience 8.6±3.3 years. Power–velocity
relationship was determined from five maximal 10-second
cycloergometer efforts with external loads equal: 2.5, 5.0, 7.5, 10.0
and 12.5% of body weight (BW) before (I) and after (II) the
preparatory period, after the first (III) and second (IV) competitive
season. The maximal power output increased from 9.30±0.85 W•kg–1
(I) to 9.50±0.96 W•kg–1 (II), 9.77±0.96 W•kg–1 (III) and 9.95±1.13
W•kg–1 (IV, p
Abstract: The present study based on removal of natural dyes of
Roselle petals, then used Roselle petals powder (RPP) as an
adsorbent for the removal of methylene blue dye (as a typical cationic
or basic dye) from aqueous solutions. The present study shows that
used Roselle petals powder exhibit adsorption trend for the dye. The
adsorption processes were carried out at various conditions of
temperatures ranging from 278 to 338 K ± 2 K , concentrations,
processing time and a wide range of pH between 2.5-11. Adsorption
isotherm equations such as Freundlich, and Langmuir were applied to
calculate the values of respective constants. Adsorption study was
found that the currently introduced adsorbent can be used to remove
cationic dyes such as methylene blue from aqueous solutions.
Abstract: Information technology managers nowadays are
facing with tremendous pressure to plan, implement, and adopt new
technology solution due to the rapidity of technology changes.
Resulted from a lack of study that have been done in this topic, the
aim of this paper is to provide a comparison review on current tools
that are currently being used in order to respond to technological
changes. The study is based on extensive literature review of
published works with majority of them are ranging from 2000 to the
first part of 2011. The works were gathered from journals, books,
and other information sources available on the Web. Findings show
that, each tools has different focus and none of the tools are
providing a framework in holistic view, which should include
technical, people, process, and business environment aspect. Hence,
this result provides potential information about current available
tools that IT managers could use to manage changes in technology.
Further, the result reveals a research gap in the area where the
industries a short of such framework.
Abstract: The demand of the energy management systems (EMS) set forth by modern power systems requires fast energy management systems. Contingency analysis is among the functions in EMS which is time consuming. In order to handle this limitation, this paper introduces agent based technology in the contingency analysis. The main function of agents is to speed up the performance. Negotiations process in decision making is explained and the issue set forth is the minimization of the operating costs. The IEEE 14 bus system and its line outage have been used in the research and simulation results are presented.