Abstract: Non-linear FEM calculations are indispensable when
important technical information like operating performance of a
rubber component is desired. For example rubber bumpers built into
air-spring structures may undergo large deformations under load,
which in itself shows non-linear behavior. The changing contact
range between the parts and the incompressibility of the rubber
increases this non-linear behavior further. The material
characterization of an elastomeric component is also a demanding
engineering task.
The shape optimization problem of rubber parts led to the study of
FEM based calculation processes. This type of problems was posed
and investigated by several authors. In this paper the time demand of
certain calculation methods are studied and the possibilities of time
reduction is presented.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: This work reports the potential of using Palm Kernel
(PK) ash and shell as a partial substitute for Portland Cement (PC)
and coarse aggregate in the development of mortar and concrete. PK
ash and shell are agro-waste materials from palm oil mills, the
disposal of PK ash and shell is an environmental problem of concern.
The PK ash has pozzolanic properties that enables it as a partial
replacement for cement and also plays an important role in the
strength and durability of concrete, its use in concrete will alleviate
the increasing challenges of scarcity and high cost of cement. In order
to investigate the PC replacement potential of PK ash, three types of
PK ash were produced at varying temperature (350-750C) and they
were used to replace up to 50% PC. The PK shell was used to replace
up to 100% coarse aggregate in order to study its aggregate
replacement potential. The testing programme included material
characterisation, the determination of compressive strength, tensile
splitting strength and chemical durability in aggressive sulfatebearing
exposure conditions. The 90 day compressive results showed
a significant strength gain (up to 26.2 N/mm2). The Portland cement
and conventional coarse aggregate has significantly higher influence
in the strength gain compared to the equivalent PK ash and PK shell.
The chemical durability results demonstrated that after a prolonged
period of exposure, significant strength losses in all the concretes
were observed. This phenomenon is explained, due to lower change
in concrete morphology and inhibition of reaction species and the
final disruption of the aggregate cement paste matrix.
Abstract: Environmental impact assessment techniques have
been developed as a result of the worldwide efforts to reduce the
environmental impact of global warming. By using the quantification
method in the construction industry, it is now possible to manage the
greenhouse gas is to systematically evaluate the impact on the
environment over the entire construction process. In particular, the
proportion of greenhouse gas emissions at the production stage of
construction material occupied is high, and efforts are needed in
particular in the construction field.
In this research, intended for concrete products for the construction
materials, by using the LCA method, we compared the results of
environmental impact assessment and carbon emissions of developing
products that have been applied low-carbon technologies compared to
existing products. As a results, by introducing a raw material of
industrial waste, showed carbon reduction. Through a comparison of
the carbon emission reduction effect of low carbon technologies, it is
intended to provide academic data for the evaluation of greenhouse
gases in the construction sector and the development of low carbon
technologies of the future.
Abstract: In rapid industrial development, the demand for
high-strength and lightweight materials have been increased. Thus,
various CFRP (Carbon Fiber Reinforced Plastics) with composite
materials are being used. The design variables of CFRP are its
lamination direction, order and thickness. Thus, the hardness and
strength of CFRP depends much on their design variables. In this
paper, the lamination direction of CFRP was used to produce a
symmetrical ply [0°/0°, -15°/+15°, -30°/+30°, -45°/+45°, -60°/+60°,
-75°/+75° and 90°/90°] and an asymmetrical ply [0°/15°, 0°/30°,
0°/45°, 0°/60° 0°/75° and 0°/90°]. The bending flexure stress of the
CFRP specimen was evaluated through a bending test. Its thermal
property was measured using an infrared camera. The symmetrical
specimen and the asymmetrical specimen were analyzed. The results
showed that the asymmetrical specimen increased the bending loads
according to the increase in the orientation angle; and from 0°, the
symmetrical specimen showed a tendency opposite the asymmetrical
tendency because the tensile force of fiber differs at the vertical
direction of its load. Also, the infrared camera showed that the thermal
property had a trend similar to that of the mechanical properties.
Abstract: Load modeling is one of the central functions in
power systems operations. Electricity cannot be stored, which means
that for electric utility, the estimate of the future demand is necessary
in managing the production and purchasing in an economically
reasonable way. A majority of the recently reported approaches are
based on neural network. The attraction of the methods lies in the
assumption that neural networks are able to learn properties of the
load. However, the development of the methods is not finished, and
the lack of comparative results on different model variations is a
problem. This paper presents a new approach in order to predict the
Tunisia daily peak load. The proposed method employs a
computational intelligence scheme based on the Fuzzy neural
network (FNN) and support vector regression (SVR). Experimental
results obtained indicate that our proposed FNN-SVR technique gives
significantly good prediction accuracy compared to some classical
techniques.
Abstract: Arising problems of countries’ public finances, social
and demographic changes motivate scientific and policy debates on
public spending size, structure and efficiency in order to meet the
changing needs of society and business. The concept of sustainable
development poses new challenges for scientists and policy-makers
in the field of public finance. This paper focuses on the investigation
of the relationship between government expenditure and country’s
economic development in the context of sustainable development.
Empirical analysis focuses on the data of the European Union (except
Croatia and Luxemburg) countries. The study covers 2003 – 2012
years, using annual cross-sectional data. Summarizing the research
results, it can be stated that governments should pay more attention to
the needs that ensure sustainable development in the long-run when
formulating public expenditure policy, particularly in the field of
environment protection.
Abstract: This study was conducted to investigate the effect of
the antioxidant activity of germinated African Yam Bean (AYB) on
oxidative stress markers in alloxan induced diabetic rat. Rats were
randomized into three groups; control, diabetic and germinated AYB
– treated diabetic rats. The Total phenol and flavonoid content and
DPPH radical scavenging activity before and after germination were
investigated. The glucose level, lipid peroxidation and reduced
glutathione of the animals were also determined using standard
technique for four weeks. Germination increased the total phenol,
flavonoid and antioxidant activity of AYB extract by 19.14%,
32.28% and 57.25% respectively. The diabetic rats placed on
germinated AYB diet had a significant decrease in the blood glucose
and lipid peroxidation with a corresponding increase in glutathione
(p
Abstract: Stator elements «Vane diffuser + crossover + return
channel» of stages with different specific speed were investigated by
CFD calculations. The regime parameter was introduced to present
efficiency and loss coefficient performance of all elements together.
Flow structure demonstrated advantages and disadvantages of design.
Flow separation in crossovers was eliminated by its shape
modification. Efficiency increased visibly. Calculated CFD
performances are in acceptable correlation with predicted ones by
engineering design method. The information obtained is useful for
design method better calibration.
Abstract: This research focused on comparing the critical
thinking of the teacher students before and after using Miller’s Model
learning activities and investigating their opinions. The sampling
groups were (1) fourth year 33 student teachers majoring in Early
Childhood Education and enrolling in semester 1 of academic year
2013 (2) third year 28 student teachers majoring in English and
enrolling in semester 2 of academic year 2013 and (3) third year 22
student teachers majoring in Thai and enrolling in semester 2 of
academic year 2013. The research instruments were (1) lesson plans
where the learning activities were settled based on Miller’s Model (2)
critical thinking assessment criteria and (3) a questionnaire on
opinions towards Miller’s Model based learning activities. The
statistical treatment was mean, deviation, different scores and T-test.
The result unfolded that (1) the critical thinking of the students after
the assigned activities was better than before and (2) the students’
opinions towards the critical thinking improvement activities based
on Miller’s Model ranged from the level of high to highest.
Abstract: In this paper, two options of anodic alumina barrier
layer thinning have been demonstrated. The approaches varied with
the duration of the voltage step. It was found that too long step of the
barrier layer thinning process leads to chemical etching of the
nanopores on their top. At the bottoms pores are not fully opened
what is disadvantageous for further applications in nanofabrication.
On the other hand, while the duration of the voltage step is controlled
by the current density (value of the current density cannot exceed
75% of the value recorded during previous voltage step) the pores are
fully opened. However, pores at the bottom obtained with this
procedure have smaller diameter, nevertheless this procedure
provides electric contact between the bare aluminum (substrate) and
electrolyte, what is suitable for template assisted electrodeposition,
one of the most cost-efficient synthesis method in nanotechnology.
Abstract: The 6th version of Universal modeling method for
centrifugal compressor stage calculation is described. Identification
of the new mathematical model was made. As a result of
identification the uniform set of empirical coefficients is received.
The efficiency definition error is 0,86 % at a design point. The
efficiency definition error at five flow rate points (except a point of
the maximum flow rate) is 1,22 %. Several variants of the stage with
3D impellers designed by 6th version program and quasi threedimensional
calculation programs were compared by their gas
dynamic performances CFD (NUMECA FINE TURBO).
Performance comparison demonstrated general principles of design
validity and leads to some design recommendations.
Abstract: Early detection of breast cancer saves many thousands
of lives each year via application of mammography and genetic
screening and many more lives could be saved if nurses are involved
in breast care screening practices. So, the aim of the study was to
identify nurse's role in early detection of breast cancer through
mammography and genetic screening and its impact on patient's
outcome. In order to achieve this aim, 400 women above 40 years,
asymptomatic were recruited for mammography and genetic
screening. In addition, 50 nurses and 6 technologists were involved in
the study. A descriptive analytical design was used. Five tools were
utilized: sociodemographic, mammographic examination and risk
factors, women's before, during and after mammography, items
relaying to technologists, and items related to nurses were also
obtained. The study finding revealed that 3% of women detected for
malignancy and 7.25% for fibroadenoma. Statistically significant
differences were found between mammography results and age,
family history, genetic screening, exposure to smoke, and using
contraceptive pills. Nurses have insufficient knowledge about
screening tests. Based on these findings the present study
recommended involvement of nurses in breast care which is very
important to in force population about screening practices.
Abstract: Iran has several potential for using renewable
energies, so use them could significantly contribute to energy supply.
The purpose of this paper is to identify the potential of the country
and select the appropriate DG technologies with consideration the
potential and primary energy resources in the regions. In this context,
hybrid energy systems proportionate with the potential of different
regions will be determined based on technical, economic, and
environmental aspect. In the following the proposed structure will be
optimized in terms of size and cost. DG technologies used in this
project include photovoltaic system, wind turbine, diesel generator
and battery bank. The HOMER software is applied for choosing the
appropriate structure and the optimization of system sizing. The
results have been analyzed in terms of technical and economic. The
performance and the cost of each project demonstrate the appropriate
structure of hybrid energy system in that region.
Abstract: Physical properties of uranium dinitride (UN2) were
investigated in detail using first principle calculations based on
density functional theory (DFT). To study the strong correlation
effects due to 5f uranium valence electrons, the on-site coulomb
interaction correction U via the Hubbard-like term (DFT+U) was
employed. The UN2 structural, mechanical and thermodynamic
properties were calculated within DFT and Various U of DFT+U
approach.
The Perdew–Burke–Ernzerhof (PBE.5.2) version of the
generalized gradient approximation (GGA) is used to describe the
exchange-correlation with the projector-augmented wave (PAW)
pseudo potentials.
A comparative study shows that results are improved by using the
Hubbard formalism for a certain U value correction like the structural
parameter. For some physical properties the variation versus
Hubbard-U is strong like Young modulus but for others it is weakly
noticeable such as bulk modulus.
We noticed also that from U=7.5 eV, elastic results don’t agree
with the cubic cell because of the C44 values which turn out to be
negative.
Abstract: This study is concerned with the optimization of
fermentation parameters for the hyper production of mannanase from
Fusarium oxysporum SS-25 employing two step statistical strategy
and kinetic characterization of crude enzyme preparation. The
Plackett-Burman design used to screen out the important factors in
the culture medium revealed 20% (w/w) wheat bran, 2% (w/w) each
of potato peels, soyabean meal and malt extract, 1% tryptone, 0.14%
NH4SO4, 0.2% KH2PO4, 0.0002% ZnSO4, 0.0005% FeSO4, 0.01%
MnSO4, 0.012% SDS, 0.03% NH4Cl, 0.1% NaNO3 in brewer’s spent
grain based medium with 50% moisture content, inoculated with
2.8×107 spores and incubated at 30oC for 6 days to be the main
parameters influencing the enzyme production. Of these factors, four
variables including soyabean meal, FeSO4, MnSO4 and NaNO3 were
chosen to study the interactive effects and their optimum levels in
central composite design of response surface methodology with the
final mannanase yield of 193 IU/gds. The kinetic characterization
revealed the crude enzyme to be active over broader temperature and
pH range. This could result in 26.6% reduction in kappa number with
4.93% higher tear index and 1% increase in brightness when used to
treat the wheat straw based kraft pulp. The hydrolytic potential of
enzyme was also demonstrated on both locust bean gum and guar
gum.
Abstract: This study attempts to elicit the perceptions and
attitudes of EFL learners of the Preparatory Year Program at KSU
towards dialogue journal writing as an EFL learning strategy. The
descriptive research design used incorporated both qualitative and
quantitative instruments to accomplish the objectives of the study. A
learners’ attitude questionnaire and follow-up interviewswith learners
from a randomly selected representative sample of the participants
were employed. The participants were 55 female Saudi university
students in the Preparatory Year Program at King Saud University.
The analysis of the results indicated that the PYP learners had highly
positive attitudes towards dialogue journal writing in their EFL
classes and positive perceptions of the benefits of the use of dialogue
journal writing as an EFL learning strategy. The results also revealed
that dialogue journals are considered an effective EFL learning
strategy since they fulfill various needs for both learners and
instructors. Interestingly, the analysis of the results also revealed that
Saudi university level students tend to write about personal topics in
their dialogue journals more than academic ones.
Abstract: Bio-composites derived from plant fiber and/or bioderived
polymer, are likely more ecofriendly and demonstrate
competitive performance with petroleum based composites. In this
research, the bio phenol-formaldehyde (bio-PF) was used as a matrix
and oil palm empty fruit bunch fiber (EFB) as reinforcement. The
matrix was synthesized via liquefaction and condensation to enhance
the combination of phenol and formaldehyde, during the process.
Then, the bio-PF was mixed with different percentage of EFB (5%,
10%, 15% and 20%) and molded at 180oC. The samples that viewed
under scanning electron microscopy (SEM) showed an excellent
wettability and interaction between EFB and matrix. Samples of 10%
EFB gave the optimum properties of impact and hardness meanwhile
sample 15% of EFB gave the highest reading of flexural modulus
(MOE) and flexural strength (MOR). For thermal stability analysis, it
was found that the weight loss and the activation energy (Ea) of the
bio-composites samples were decreased as the filler content
increased.
Abstract: Managing and improving efficiency in the current
highly competitive global automotive industry demands that those
companies adopt leaner and more flexible systems. During the past
20 years the domestic automotive industry in North America has been
focusing on establishing new management strategies in order to meet
market demands. The lean management process also known as
Toyota Manufacturing Process (TPS) or lean manufacturing
encompasses tools and techniques that were established in order to
provide the best quality product with the fastest lead time at the
lowest cost. The following paper presents a study that focused on
improving labor efficiency at one of the Big Three (Ford, GM,
Chrysler LLC) domestic automotive facility in North America. The
objective of the study was to utilize several lean management tools in
order to optimize the efficiency and utilization levels at the “Pre-
Marriage” chassis area in a truck manufacturing and assembly
facility. Utilizing three different lean tools (i.e. Standardization of
work, 7 Wastes, and 5S) this research was able to improve efficiency
by 51%, utilization by 246%, and reduce operations by 14%. The
return on investment calculated based on the improvements made
was 284%.
Abstract: Eucalyptus species are well reputed for their
traditional use in Asia as well as in other parts of the world; therefore,
the present study was designed to investigate the antimicrobial and
antioxidant activities associated with essential oils from different
Eucalyptus species. Essential oils from the leaves of six Eucalyptus
species, including: Eucalyptus woodwardi, Eucalyptus stricklandii,
Eucalyptus salubris, Eucalyptus sargentii, Eucalyptus torquata and
Eucalyptus wandoo were separated by hydrodistillation and dried
over anhydrous sodium sulphate. DPPH, ferric reducing antioxidant
power, and hydroxyl radical scavenging activity assays were carried
out to evaluate the antioxidant potential of the oils. The results
indicate that examined oils exhibit substantial antioxidant activities
relative to ascorbic acid. Previously, these oils were evaluated for
their antimicrobial activities, against wide range of bacterial and
fungal strains, and they were shown to possess significant
antimicrobial activities. In this study, further investigation into the
growth kinetics of oil-treated microbial cultures was conducted. The
results clearly demonstrate that the microbial growth was markedly
inhibited when treated with sub-MIC concentrations of the oils.
Taken together, the results obtained indicate a high potential of the
examined essential oils as bioactive oils, for nutraceutical and
medical applications, possessing significant antioxidant and anti
microbial activities.