Abstract: The reluctance motor is an electric motor in which
torque is produced by the tendency of its moveable part to move to a
position where the inductance of the excited winding is maximized.
In this paper switched reluctance motors (SRMs) with two different
configurations(3-phase SRM with 4rotor poles and 6 stator poles, 4-
phase SRM with 6rotor poles and 8 stator poles) is designed by
RMxprt, and performance of them is analyzed. Efficiency and torque
of SRM for different configurations in full-load condition have been
presented. The results indicate that with correct choosing of motor
applications, maximum efficiency can be found.
Abstract: This paper describes a CMOS four-quadrant
multiplier intended for use in the front-end receiver by utilizing the
square-law characteristic of the MOS transistor in the saturation
region. The circuit is based on 0.35 um CMOS technology simulated
using HSPICE software. The mixer has a third-order inter the power
consumption is 271uW from a single 1.2V power supply. One of the
features of the proposed design is using two MOS transistors
limitation to reduce the supply voltage, which leads to reduce the
power consumption. This technique provides a GHz bandwidth
response and low power consumption.
Abstract: The inphase/quadrature (I/Q) amplitude and phase
imbalance effects are studied in coherent optical orthogonal
frequency division multiplexing (CO-OFDM) systems. An analytical
model for the I/Q imbalance is developed and supported by
simulation results. The results indicate that the I/Q imbalance degrades the BER performance considerably.
Abstract: This paper presents the experimental results on effect of applied voltage stress frequency to the occurrence of electrical treeing in 22 kV cross linked polyethylene (XLPE) insulated cable.Hallow disk of XLPE insulating material with thickness 5 mm taken from unused high voltage cable was used as the specimen in this study. Stainless steel needle was inserted gradually into the specimen to give a tip to earth plane electrode separation of 2.50.2 mm at elevated temperature 105-110°C. The specimen was then annealed for 5 minute to minimize any mechanical stress build up around the needle-plane region before it was cooled down to room temperature. Each specimen were subjected to the same applied voltage stress level at 8 kV AC rms, with various frequency, 50, 100, 500, 1000 and 2000 Hz. Initiation time, propagation speed and pattern of electrical treeing were examined in order to study the effect of applied voltage stress frequency. By the experimental results, initial time of visible treeing decreases with increasing in applied voltage frequency. Also, obviously, propagation speed of electrical treeing increases with increasing in applied voltage frequency.Furthermore, two types of electrical treeing, bush-like and branch-like treeing were observed.The experimental results confirmed the effect of voltage stress frequency as well.
Abstract: Piezoelectric transformers are electronic devices made
from piezoelectric materials. The piezoelectric transformers as the
name implied are used for changing voltage signals from one level to another. Electrical energy carried with signals is transferred by means of mechanical vibration. Characterizing in both electrical and
mechanical properties leads to extensively use and efficiency enhancement of piezoelectric transformers in various applications. In
this paper, study and analysis of electrical and mechanical properties of multi-layer piezoelectric transformers in forms of potential and
displacement distribution throughout the volume, respectively. This
paper proposes a set of quasi-static mathematical model of electromechanical
coupling for piezoelectric transformer by using a set of
partial differential equations. Computer-based simulation utilizing the three-dimensional finite element method (3-D FEM) is exploited
as a tool for visualizing potentials and displacements distribution
within the multi-layer piezoelectric transformer. This simulation was
conducted by varying a number of layers. In this paper 3, 5 and 7 of
the circular ring type were used. The computer simulation based on
the use of the FEM has been developed in MATLAB programming environment.
Abstract: Orthogonal frequency division multiplexing (OFDM)
has developed into a popular scheme for wideband digital
communications used in consumer applications such as digital broadcasting, wireless networking and broadband internet access. In
the OFDM system, carrier frequency offset (CFO) causes intercarrier
interference (ICI) which significantly degrades the system error performance. In this paper we provide an exact evaluation method for error performance analysis of arbitrary 2-D modulation OFDM systems with CFO, and analyze the effect of CFO on error performance.
Abstract: This paper aims to present the reviews of the
application of neural network in shunt active power filter (SAPF).
From the review, three out of four components of SAPF structure,
which are harmonic detection component, compensating current
control, and DC bus voltage control, have been adopted some of
neural network architecture as part of its component or even
substitution. The objectives of most papers in using neural network in
SAPF are to increase the efficiency, stability, accuracy, robustness,
tracking ability of the systems of each component. Moreover,
minimizing unneeded signal due to the distortion is the ultimate goal
in applying neural network to the SAPF. The most famous
architecture of neural network in SAPF applications are ADALINE
and Backpropagation (BP).
Abstract: The paper presents the applications of artificial
intelligence technique called adaptive tabu search to design the
controller of a buck converter. The averaging model derived from the
DQ and generalized state-space averaging methods is applied to
simulate the system during a searching process. The simulations
using such averaging model require the faster computational time
compared with that of the full topology model from the software
packages. The reported model is suitable for the work in the paper in
which the repeating calculation is needed for searching the best
solution. The results will show that the proposed design technique
can provide the better output waveforms compared with those
designed from the classical method.
Abstract: This paper presents the mathematical model and
control strategy on DQ frame of shunt active power filter. The
structure of the shunt active power filter is the voltage source inverter
(VSI). The pulse width modulation (PWM) with PI controller is used
in the paper. The concept of DQ frame to apply with the shunt active
power filter is described. Moreover, the detail of the PI controller
design for two current loops and one voltage loop are fully explained.
The DQ axis with Fourier (DQF) method is applied to calculate the
reference currents on DQ frame. The simulation results show that the
control strategy and the design method presented in the paper can
provide the good performance of the shunt active power filter.
Moreover, the %THD of the source currents after compensation can
follow the IEEE Std.519-1992.
Abstract: Space-time block codes (STBC) and spatial multiplexing
(SM) are promising techniques that effectively exploit multipleinput
multiple-output (MIMO) transmission to achieve more reliable
communication and a higher multiplexing rate, respectively. In this
paper, we study a practical design for hybrid scheme with multi-input
multi-output orthogonal frequency division multiplexing (MIMOOFDM)
systems to flexibly maximize the tradeoff between diversity
and multiplexing gains. Unlike the existing STBC and SM designs
which are suitable for the integer multiplexing rate, the proposed
design can achieve arbitrary number of multiplexing rate.
Abstract: The study of piezoelectric material in the past was in T-Domain form; however, no one has studied piezoelectric material in the S-Domain form. This paper will present the piezoelectric material in the transfer function or S-Domain model. S-Domain is a well known mathematical model, used for analyzing the stability of the material and determining the stability limits. By using S-Domain in testing stability of piezoelectric material, it will provide a new tool for the scientific world to study this material in various forms.
Abstract: Bangladesh is a developing country with large
population. Demand of electrical energy is increasing day by day
because of increasing population and industrialization. But due to
limited resources, people here are suffering from power crisis
problem which is considered as a major obstacle to the economic
development. In most of the cases, it is extremely difficult to extend
high tension transmission lines to some of the places that are
separated from the mainland. Renewable energy is considered to be
the right choice for providing clean energy to these remote
settlements. This paper proposes a cost effective design of off-grid
wind-diesel hybrid power system using combined heat and power
(CHP) technology in a grid isolated island, Sandwip, Bangladesh.
Design and simulation of the wind-diesel hybrid power system is
performed considering different factors for the island Sandwip.
Detailed economic analysis and comparison with solar PV system
clearly reveals that wind-diesel hybrid power system can be a cost
effective solution for the isolated island like Sandwip.
Abstract: This paper demonstrates the application of craziness based particle swarm optimization (CRPSO) technique for designing the 8th order low pass Infinite Impulse Response (IIR) filter. CRPSO, the much improved version of PSO, is a population based global heuristic search algorithm which finds near optimal solution in terms of a set of filter coefficients. Effectiveness of this algorithm is justified with a comparative study of some well established algorithms, namely, real coded genetic algorithm (RGA) and particle swarm optimization (PSO). Simulation results affirm that the proposed algorithm CRPSO, outperforms over its counterparts not only in terms of quality output i.e. sharpness at cut-off, pass band ripple, stop band ripple, and stop band attenuation but also in convergence speed with assured stability.
Abstract: As new challenges emerge in power electrical
workplace safety, it is the responsibility of the systems designer to
seek out new approaches and solutions that address them. Design
decisions made today will impact cost, safety and serviceability of
the installed systems for 40 or 50 years during the useful life for the
owner. Studies have shown that this cost is an order of magnitude of
7 to 10 times the installed cost of the power distribution equipment.
This paper reviews some aspects of earthing system design in power
substation surrounded by residential houses. The electrical potential
rise and split factors are discussed and a few recommendations are
provided to achieve a safety voltage in the area beyond the boundary
of the substation.
Abstract: In this paper, a modified CCCII is presented. We have used a current mirror with low supply voltage. This circuit is operated at low supply voltage of ±1V. Tspice simulations for TSMC 0.18μm CMOS Technology has shown that the current and voltage bandwidth are respectively 3.34GHz and 4.37GHz, and parasitic resistance at port X has a value of 169.320 for a control current of 120μA. In order to realize this circuit, we have implemented in this first step a universal current mode filter where the frequency can reach the 134.58MHz. In the second step, we have implemented two simulated inductors: one floating and the other grounded. These two inductors are operated in high frequency and variable depending on bias current I0. Finally, we have used the two last inductors respectively to implement two sinusoidal oscillators domains of frequencies respectively: [470MHz, 692MHz], and [358MHz, 572MHz] for bias currents I0 [80μA, 350μA].