Abstract: In order to enhance the aircraft survivability, the
infrared signatures emitted by hot engine parts should be determined
exactly. For its reduction it is necessary for the rear fuselage
temperature to be decreased. In this study, numerical modeling of flow
fields and heat transfer characteristics of an aircraft nozzle is
performed and its temperature distribution along each component wall
is predicted. The radiation shield is expected to reduce the skin
temperature of rear fuselage. The effect of material characteristic of
radiation shield on the heat transfer is also investigated. Through this
numerical analysis, design parameters related to the susceptibility of
aircraft are examined.
Abstract: Higher capacities of power plants together with
increased awareness on environmental considerations have led to
taller height of stacks. It is seen that strong wind can result in falling
of stacks. So, aerodynamic consideration of stacks is very important
in order to save the falling of stacks. One stack is not enough in
industries and power sectors and two or three stacks are required for
proper operation of the unit. It is very important to arrange the stacks
in proper way to resist their downfall. The present experimental
study concentrates on the mutual effect of three nearby stacks on
each other at three different arrangements, viz. linear, side-by-side
and triangular. The experiments find out the directions of resultant
forces acting on the stacks in different configurations so that proper
arrangement of supports can be made with respect to the wind
directionality obtained from local meteorological data. One can also
easily ascertain which stack is more vulnerable to wind in
comparison to the others for a particular configuration. Thus, this
study is important in studying the effect of wind force on three stacks
in different arrangements and is very helpful in placing the supports
in proper places in order to avoid failing of stack-like structures due
to wind.
Abstract: Unmanned aerial vehicles (UAVs) performing their
operations for a long time have been attracting much attention in
military and civil aviation industries for the past decade. The
applicable field of UAV is changing from the military purpose only to
the civil one. Because of their low operation cost, high reliability and
the necessity of various application areas, numerous development
programs have been initiated around the world. To obtain the optimal
solutions of the design variable (i.e., sectional airfoil profile, wing
taper ratio and sweep) for high performance of UAVs, both the lift and
lift-to-drag ratio are maximized whereas the pitching moment should
be minimized, simultaneously. It is found that the lift force and
lift-to-drag ratio are linearly dependent and a unique and dominant
solution are existed. However, a trade-off phenomenon is observed
between the lift-to-drag ratio and pitching moment. As the result of
optimization, sixty-five (65) non-dominated Pareto individuals at the
cutting edge of design spaces that are decided by airfoil shapes can be
obtained.
Abstract: This paper is devoted to predict laminar and turbulent
heating rates around blunt re-entry spacecraft at hypersonic
conditions. Heating calculation of a hypersonic body is normally
performed during the critical part of its flight trajectory. The
procedure is of an inverse method, where a shock wave is assumed,
and the body shape that supports this shock, as well as the flowfield
between the shock and body, are calculated. For simplicity the
normal momentum equation is replaced with a second order pressure
relation; this simplification significantly reduces computation time.
The geometries specified in this research, are parabola and ellipsoids
which may have conical after bodies. An excellent agreement is
observed between the results obtained in this paper and those
calculated by others- research. Since this method is much faster than
Navier-Stokes solutions, it can be used in preliminary design,
parametric study of hypersonic vehicles.
Abstract: The aerodynamic stall control of a baseline 13-percent
thick NASA GA(W)-2 airfoil using a synthetic jet actuator (SJA) is
presented in this paper. Unsteady Reynolds-averaged Navier-Stokes
equations are solved on a hybrid grid using a commercial software to
simulate the effects of a synthetic jet actuator located at 13% of the
chord from the leading edge at a Reynolds number Re = 2.1x106 and
incidence angles from 16 to 22 degrees. The experimental data for the
pressure distribution at Re = 3x106 and aerodynamic coefficients at
Re = 2.1x106 (angle of attack varied from -16 to 22 degrees) without
SJA is compared with the computational fluid dynamic (CFD)
simulation as a baseline validation. A good agreement of the CFD
simulations is obtained for aerodynamic coefficients and pressure
distribution.
A working SJA has been integrated with the baseline airfoil and
initial focus is on the aerodynamic stall control at angles of attack
from 16 to 22 degrees. The results show a noticeable improvement in
the aerodynamic performance with increase in lift and decrease in
drag at these post stall regimes.
Abstract: This paper describes Nano-particle based Planar Laser
Scattering (NPLS) flow visualization of angled supersonic jets into a
supersonic cross flow based on the HYpersonic Low TEmperature
(HYLTE) nozzle which was widely used in DF chemical laser. In
order to investigate the non-reacting flowfield in the HYLTE nozzle, a
testing section with windows was designed and manufactured. The
impact of secondary fluids orifice separation on mixing was examined.
For narrow separation of orifices, the secondary fuel penetration
increased obviously compared to diluent injection, which means
smaller separation of diluent and fuel orifices would enhance the
mixing of fuel and oxidant. Secondary injections with angles of 30, 40
and 50 degrees were studied. It was found that the injectant
penetration increased as the injection angle increased, while the
interfacial surface area to entrain the freestream fluid is largest when
the injection angle is 40 degree.
Abstract: In this paper a simple terrain evaluation method for
hexapod robot is introduced. This method is based on feet coordinate
evaluation when all are on the ground. Depending on the feet
coordinate differences the local terrain evaluation is possible. Terrain
evaluation is necessary for right gait selection and/or body position
correction. For terrain roughness evaluation three planes are plotted:
two of them as definition points use opposite feet coordinates, third
coincides with the robot body plane. The leaning angle of body plane
is evaluated measuring gravity force using three-axis accelerometer.
Terrain roughness evaluation method is based on angle estimation
between normal vectors of these planes. Aim of this work is to
present a simple method for embedded robot controller, allowing to
find the best further movement settings.
Abstract: Researches show that probability-statistical methods application, especially at the early stage of the aviation Gas Turbine Engine (GTE) technical condition diagnosing, when the flight information has property of the fuzzy, limitation and uncertainty is unfounded. Hence the efficiency of application of new technology Soft Computing at these diagnosing stages with the using of the Fuzzy Logic and Neural Networks methods is considered. According to the purpose of this problem training with high accuracy of fuzzy multiple linear and non-linear models (fuzzy regression equations) which received on the statistical fuzzy data basis is made. For GTE technical condition more adequate model making dynamics of skewness and kurtosis coefficients- changes are analysed. Researches of skewness and kurtosis coefficients values- changes show that, distributions of GTE work parameters have fuzzy character. Hence consideration of fuzzy skewness and kurtosis coefficients is expedient. Investigation of the basic characteristics changes- dynamics of GTE work parameters allows drawing conclusion on necessity of the Fuzzy Statistical Analysis at preliminary identification of the engines' technical condition. Researches of correlation coefficients values- changes shows also on their fuzzy character. Therefore for models choice the application of the Fuzzy Correlation Analysis results is offered. At the information sufficiency is offered to use recurrent algorithm of aviation GTE technical condition identification (Hard Computing technology is used) on measurements of input and output parameters of the multiple linear and non-linear generalised models at presence of noise measured (the new recursive Least Squares Method (LSM)). The developed GTE condition monitoring system provides stageby- stage estimation of engine technical conditions. As application of the given technique the estimation of the new operating aviation engine technical condition was made.
Abstract: This paper presents a longitudinal quasi-linear model for the ADMIRE model. The ADMIRE model is a nonlinear model of aircraft flying in the condition of high angle of attack. So it can-t be considered to be a linear system approximately. In this paper, for getting the longitudinal quasi-linear model of the ADMIRE, a state transformation based on differentiable functions of the nonscheduling states and control inputs is performed, with the goal of removing any nonlinear terms not dependent on the scheduling parameter. Since it needn-t linear approximation and can obtain the exact transformations of the nonlinear states, the above-mentioned approach is thought to be appropriate to establish the mathematical model of ADMIRE. To verify this conclusion, simulation experiments are done. And the result shows that this quasi-linear model is accurate enough.
Abstract: The present paper deals with the most adopted technical
solutions for the enhancement of the lift force of a wing. In fact,
during several flight conditions (such as take off and landing), the
lift force needs to be dramatically enhanced. Both trailing edge
devices (such as flaps) and leading edge ones (such as slats) are
described. Finally, the most advanced aerodynamic solutions to avoid
the separation of the boundary layer from aircraft wings at high angles
of attack are reviewed.
Abstract: In this paper the supersonic ejectors are
experimentally and analytically studied. Ejector is a device that
uses the energy of a fluid to move another fluid. This device works
like a vacuum pump without usage of piston, rotor or any other
moving component. An ejector contains an active nozzle, a passive
nozzle, a mixing chamber and a diffuser. Since the fluid viscosity
is large, and the flow is turbulent and three dimensional in the
mixing chamber, the numerical methods consume long time and
high cost to analyze the flow in ejectors. Therefore this paper
presents a simple analytical method that is based on the precise
governing equations in fluid mechanics. According to achieved
analytical relations, a computer code has been prepared to analyze
the flow in different components of the ejector. An experiment has
been performed in supersonic regime 1.5
Abstract: Series of experimental tests were conducted on a
section of a 660 kW wind turbine blade to measure the pressure
distribution of this model oscillating in plunging motion. In order to
minimize the amount of data required to predict aerodynamic loads
of the airfoil, a General Regression Neural Network, GRNN, was
trained using the measured experimental data. The network once
proved to be accurate enough, was used to predict the flow behavior
of the airfoil for the desired conditions.
Results showed that with using a few of the acquired data, the
trained neural network was able to predict accurate results with
minimal errors when compared with the corresponding measured
values. Therefore with employing this trained network the
aerodynamic coefficients of the plunging airfoil, are predicted
accurately at different oscillation frequencies, amplitudes, and angles
of attack; hence reducing the cost of tests while achieving acceptable
accuracy.
Abstract: In this article, the flow behavior around a NACA 0012 airfoil which is oscillating with different Reynolds numbers and in various amplitudes has been investigated numerically. Numerical simulations have been performed with ANSYS software. First, the 2- D geometry has been studied in different Reynolds numbers and angles of attack with various numerical methods in its static condition. This analysis was to choose the best turbulent model and comparing the grids to have the optimum one for dynamic simulations. Because the analysis was to study the blades of wind turbines, the Reynolds numbers were not arbitrary. They were in the range of 9.71e5 to 22.65e5. The angle of attack was in the range of -41.81° to 41.81°. By choosing the forward wind speed as the independent parameter, the others like Reynolds and the amplitude of the oscillation would be known automatically. The results show that the SST turbulent model is the best choice that leads the least numerical error with respect the experimental ones. Also, a dynamic stall phenomenon is more probable at lower wind speeds in which the lift force is less.
Abstract: Flow field around hypersonic vehicles is very
complex and difficult to simulate. The boundary layers are squeezed
between shock layer and body surface. Resolution of boundary layer,
shock wave and turbulent regions where the flow field has high
values is difficult of capture. Detached eddy simulation (DES) is a
modification of a RANS model in which the model switches to a
subgrid scale formulation in regions fine enough for LES
calculations. Regions near solid body boundaries and where the
turbulent length scale is less than the maximum grid dimension are
assigned the RANS mode of solution. As the turbulent length scale
exceeds the grid dimension, the regions are solved using the LES
mode. Therefore the grid resolution is not as demanding as pure LES,
thereby considerably cutting down the cost of the computation. In
this research study hypersonic flow is simulated at Mach 8 and
different angle of attacks to resolve the proper boundary layers and
discontinuities. The flow is also simulated in the long wake regions.
Mesh is little different than RANS simulations and it is made dense
near the boundary layers and in the wake regions to resolve it
properly. Hypersonic blunt cone cylinder body with frustrum at angle
5o and 10 o are simulated and there aerodynamics study is performed
to calculate aerodynamics characteristics of different geometries. The
results and then compared with experimental as well as with some
turbulence model (SA Model). The results achieved with DES
simulation have very good resolution as well as have excellent
agreement with experimental and available data. Unsteady
simulations are performed for DES calculations by using duel time
stepping method or implicit time stepping. The simulations are
performed at Mach number 8 and angle of attack from 0o to 10o for
all these cases. The results and resolutions for DES model found
much better than SA turbulence model.
Abstract: This paper is focusing on designing a control system
for wind turbine which can control the speed and output power
according to arbitrary algorithm. Reference Tracking Method is used
to control the turbine spinning speed in order to increase its output
energy.
Abstract: The design of a landing gear is one of the fundamental aspects of aircraft design. The need for a light weight, high strength, and stiffness characteristics coupled with techno economic feasibility are a key to the acceptability of any landing gear construction. In this paper, an approach for analyzing two different designed landing gears for an unmanned aircraft vehicle (UAV) using advanced CAE techniques will be applied. Different landing conditions have been considered for both models. The maximum principle stresses for each model along with the factor of safety are calculated for every loading condition. A conclusion is drawing about better geometry.
Abstract: This paper presents a cold flow simulation study of a small gas turbine combustor performed using laboratory scale test rig. The main objective of this investigation is to obtain physical insight of the main vortex, responsible for the efficient mixing of fuel and air. Such models are necessary for predictions and optimization of real gas turbine combustors. Air swirler can control the combustor performance by assisting in the fuel-air mixing process and by producing recirculation region which can act as flame holders and influences residence time. Thus, proper selection of a swirler is needed to enhance combustor performance and to reduce NOx emissions. Three different axial air swirlers were used based on their vane angles i.e., 30°, 45°, and 60°. Three-dimensional, viscous, turbulent, isothermal flow characteristics of the combustor model operating at room temperature were simulated via Reynolds- Averaged Navier-Stokes (RANS) code. The model geometry has been created using solid model, and the meshing has been done using GAMBIT preprocessing package. Finally, the solution and analysis were carried out in a FLUENT solver. This serves to demonstrate the capability of the code for design and analysis of real combustor. The effects of swirlers and mass flow rate were examined. Details of the complex flow structure such as vortices and recirculation zones were obtained by the simulation model. The computational model predicts a major recirculation zone in the central region immediately downstream of the fuel nozzle and a second recirculation zone in the upstream corner of the combustion chamber. It is also shown that swirler angles changes have significant effects on the combustor flowfield as well as pressure losses.
Abstract: The objective of this study is to present the test
results of variable air volume (VAV) air conditioning system
optimized by two objective genetic algorithm (GA). The objective
functions are energy savings and thermal comfort. The optimal set
points for fuzzy logic controller (FLC) are the supply air temperature
(Ts), the supply duct static pressure (Ps), the chilled water
temperature (Tw), and zone temperature (Tz) that is taken as the
problem variables. Supply airflow rate and chilled water flow rate are
considered to be the constraints. The optimal set point values are
obtained from GA process and assigned into fuzzy logic controller
(FLC) in order to conserve energy and maintain thermal comfort in
real time VAV air conditioning system. A VAV air conditioning
system with FLC installed in a software laboratory has been taken for
the purpose of energy analysis. The total energy saving obtained in
VAV GA optimization system with FLC compared with constant air
volume (CAV) system is expected to achieve 31.5%. The optimal
duct static pressure obtained through Genetic fuzzy methodology
attributes to better air distribution by delivering the optimal quantity
of supply air to the conditioned space. This combination enhanced
the advantages of uniform air distribution, thermal comfort and
improved energy savings potential.
Abstract: The aim of this work is to present a multi-objective optimization method to find maximum efficiency kinematics for a flapping wing unmanned aerial vehicle. We restrained our study to rectangular wings with the same profile along the span and to harmonic dihedral motion. It is assumed that the birdlike aerial vehicle (whose span and surface area were fixed respectively to 1m and 0.15m2) is in horizontal mechanically balanced motion at fixed speed. We used two flight physics models to describe the vehicle aerodynamic performances, namely DeLaurier-s model, which has been used in many studies dealing with flapping wings, and the model proposed by Dae-Kwan et al. Then, a constrained multi-objective optimization of the propulsive efficiency is performed using a recent evolutionary multi-objective algorithm called є-MOEA. Firstly, we show that feasible solutions (i.e. solutions that fulfil the imposed constraints) can be obtained using Dae-Kwan et al.-s model. Secondly, we highlight that a single objective optimization approach (weighted sum method for example) can also give optimal solutions as good as the multi-objective one which nevertheless offers the advantage of directly generating the set of the best trade-offs. Finally, we show that the DeLaurier-s model does not yield feasible solutions.
Abstract: In space during functioning, a satellite will be heated
up due to the behavior of its components such as power electronics.
In order to prevent problems in the satellite, this heat has to be
released in space thanks to the cooling system. This system consists
of a loop heat pipe (LHP), in which a fluid streams through an
evaporator and a condenser. In the evaporator, the fluid captures the
heat from the satellite and evaporates. Then it flows to the condenser
where it releases the heat and it condenses. In this project, the two
mains parts of a cooling system are studied: the evaporator and the
condenser. The study of the diphasic loop was done starting from
digital simulations carried out under Matlab and Femlab.