Abstract: This paper describes vibration analysis using the finite
element method for a small earphone, especially for the diaphragm
shape with a low-rigidity. The viscoelastic diaphragm is supported by
multiple nonlinear concentrated springs with linear hysteresis
damping. The restoring forces of the nonlinear springs have cubic
nonlinearity. The finite elements for the nonlinear springs with
hysteresis are expressed and are connected to the diaphragm that is
modeled by linear solid finite elements in consideration of a complex
modulus of elasticity. Further, the discretized equations in physical
coordinates are transformed into the nonlinear ordinary coupled
equations using normal coordinates corresponding to the linear natural
modes. We computed the nonlinear stationary and non-stationary
responses due to the internal resonance between modes with large
amplitude in the nonlinear springs and elastic modes in the diaphragm.
The non-stationary motions are confirmed as the chaos due to the
maximum Lyapunov exponents with a positive number. From the time
histories of the deformation distribution in the chaotic vibration, we
identified nonlinear modal couplings.
Abstract: Mobile Ad hoc Networks is an autonomous system of
mobile nodes connected by multi-hop wireless links without
centralized infrastructure support. As mobile communication gains
popularity, the need for suitable ad hoc routing protocols will
continue to grow. Efficient dynamic routing is an important research
challenge in such a network. Bandwidth constrained mobile devices
use on-demand approach in their routing protocols because of its
effectiveness and efficiency. Many researchers have conducted
numerous simulations for comparing the performance of these
protocols under varying conditions and constraints. Most of them are
not aware of MAC Protocols, which will impact the relative
performance of routing protocols considered in different network
scenarios. In this paper we investigate the choice of MAC protocols
affects the relative performance of ad hoc routing protocols under
different scenarios. We have evaluated the performance of these
protocols using NS2 simulations. Our results show that the
performance of routing protocols of ad hoc networks will suffer when
run over different MAC Layer protocols.
Abstract: Developing a supply chain management (SCM) system is costly, but important. However, because of its complicated nature, not many of such projects are considered successful. Few research publications directly relate to key success factors (KSFs) for implementing a SCM system. Motivated by the above, this research proposes a hierarchy of KSFs for SCM system implementation in the semiconductor industry by using a two-step approach. First, the literature review indicates the initial hierarchy. The second step includes a focus group approach to finalize the proposed KSF hierarchy by extracting valuable experiences from executives and managers that actively participated in a project, which successfully establish a seamless SCM integration between the world's largest semiconductor foundry manufacturing company and the world's largest assembly and testing company. Future project executives may refer the resulting KSF hierarchy as a checklist for SCM system implementation in semiconductor or related industries.
Abstract: This paper presented the technique of robot control by event-related potentials (ERPs) of brain waves. Based on the proposed technique, severe physical disabilities can free browse outside world. A specific component of ERPs, N2P3, was found and used to control the movement of robot and the view of camera on the designed brain-computer interface (BCI). Users only required watching the stimuli of attended button on the BCI, the evoked potentials of brain waves of the target button, N2P3, had the greatest amplitude among all control buttons. An experimental scene had been constructed that the robot required walking to a specific position and move the view of camera to see the instruction of the mission, and then completed the task. Twelve volunteers participated in this experiment, and experimental results showed that the correct rate of BCI control achieved 80% and the average of execution time was 353 seconds for completing the mission. Four main contributions included in this research: (1) find an efficient component of ERPs, N2P3, for BCI control, (2) embed robot's viewpoint image into user interface for robot control, (3) design an experimental scene and conduct the experiment, and (4) evaluate the performance of the proposed system for assessing the practicability.
Abstract: To compute dynamic characteristics of nonlinear viscoelastic springs with elastic structures having huge degree-of-freedom, Yamaguchi proposed a new fast numerical method using finite element method [1]-[2]. In this method, restoring forces of the springs are expressed using power series of their elongation. In the expression, nonlinear hysteresis damping is introduced. In this expression, nonlinear complex spring constants are introduced. Finite element for the nonlinear spring having complex coefficients is expressed and is connected to the elastic structures modeled by linear solid finite element. Further, to save computational time, the discrete equations in physical coordinate are transformed into the nonlinear ordinary coupled equations using normal coordinate corresponding to linear natural modes. In this report, the proposed method is applied to simulation for impact responses of a viscoelastic shock absorber with an elastic structure (an S-shaped structure) by colliding with a concentrated mass. The concentrated mass has initial velocities and collides with the shock absorber. Accelerations of the elastic structure and the concentrated mass are measured using Levitation Mass Method proposed by Fujii [3]. The calculated accelerations from the proposed FEM, corresponds to the experimental ones. Moreover, using this method, we also investigate dynamic errors of the S-shaped force transducer due to elastic mode in the S-shaped structure.
Abstract: A study of various turbulent inflow generation methods
was performed to compare their relative effectiveness for LES
computations of turbulent boundary layers. This study confirmed
the quality of the turbulent information produced by the family of
recycling and rescaling methods which take information from within
the computational domain. Furthermore, more general inflow methods
also proved applicable to such simulations, with a precursor-like
inflow and a random inflow augmented with forcing planes showing
promising results.
Abstract: Microorganisms isolated from water and soil of
Kazakhstan to identify potential high-effective producers of the
arachidonic acid, exhibiting a wide range of physiological activity
and having practical applications were screened. Based on the results
of two independent tests (the test on the sensitivity of the growth
processes of microorganisms to acetylsalicylic acid - an irreversible
inhibitor of PGH-synthase involved in the metabolism of arachidonic
acid and its derivatives, the test for inhibition of peroxidase activity
of membrane-bounding fraction of PGH - synthase by acetylsalicylic
acid) were selected microbial cultures which are potential highproducer
of arachidonic acid. They are characterized by a stable
strong growth in the laboratory conditions. Identification of
microorganism cultures based on morphological, physiological,
biochemical and molecular genetic characteristics was performed.
Abstract: Today-s Voltage Regulator Modules (VRMs) face increasing design challenges as the number of transistors in microprocessors increases per Moore-s Law. These challenges have recently become even more demanding as microprocessors operate at sub voltage range at significantly high current. This paper presents a new multiphase topology with cell configuration for improved performance in low voltage and high current applications. A lab scale hardware prototype of the new topology was design and constructed. Laboratory tests were performed on the proposed converter and compared with a commercially available VRM. Results from the proposed topology exhibit improved performance compared to the commercially available counterpart.
Abstract: This research were investigated, determined, and
analyzed of the climate characteristically change in the provincial
Udon Thani in the period of 60 surrounding years from 1951 to 2010
A.D. that it-s transferred to effects of climatologically data for
determining global warming. Statistically significant were not found
for the 60 years- data (R2
Abstract: The implementation of electronic government started since the initiation of Multimedia Super Corridor (MSC) by the Malaysia government. The introduction of ICT in the public sector especially e-Government initiatives opens up a new book in the government administration throughout the world. The aim or this paper is to discuss the implementation of e-government in Malaysia, covering the result of public user self assessment on Malaysia's electronic government applications. E-services, e-procurement, Generic Office Environment (GOE), Human Resources Management Information System (HRMIS), Project Monitoring System (PMS), Electronic Labor Exchange (ELX) and e-syariah(religion) were the seven flagship application assessed. The study adopted a crosssectional survey research approach and information system literature were used. The analysis was done for 35 responden in pilot test and there was evidence from public user's perspective to suggest that the e-government applications were generally successful.
Abstract: Plackett-Burman statistical screening of media
constituents and operational conditions for extracellular lipase
production from isolate Trichoderma viride has been carried out in
submerged fermentation. This statistical design is used in the early
stages of experimentation to screen out unimportant factors from a
large number of possible factors. This design involves screening of
up to 'n-1' variables in just 'n' number of experiments. Regression
coefficients and t-values were calculated by subjecting the
experimental data to statistical analysis using Minitab version 15.
The effects of nine process variables were studied in twelve
experimental trials. Maximum lipase activity of 7.83 μmol /ml /min
was obtained in the 6th trail. Pareto chart illustrates the order of
significance of the variables affecting the lipase production. The
present study concludes that the most significant variables affecting
lipase production were found to be palm oil, yeast extract, K2HPO4,
MgSO4 and CaCl2.
Abstract: An exploratory computational investigation using
RANS & URANS was carried out to understand the aerodynamics
around an isolatedsingle rotating wheel with decreasing ground
proximity. The wheel was initially modeled in free air conditions,
then with decreasing ground proximity and increased yaw angle with
rotational speeds. Three speeds of rotation were applied to the wheel
so that the effect of different angular velocities can be investigated. In
addition to rotation, three different yaw angles were applied to the
rotating wheel in order to understand how these two variables
combined affect the aerodynamic flow field around the wheel.
Abstract: Friction Stir Welding (FSW) is a solid state welding
process invented and patented by The Welding Institute (TWI) in the
United Kingdom in 1991 for butt and lap welding of metals and plastics. This paper highlights the benefits of friction stir welding
process as an energy efficient and a green technology process in the
field of welding. Compared to the other conventional welding processes, its benefits, typical applications and its use in joining
similar and dissimilar materials are also presented.
Abstract: The purpose of this research study is to investigate the manner in which various loads affect the mechanical properties of the formed mild steel plates. The investigation focuses on examining the cross-sectional area of the metal plate at the centre of the formed mild steel plate. Six mild steel plates were deformed with different loads. The loads applied on the plates had a magnitude of 5 kg, 10 kg, 15 kg, 20 kg, 25 kg and 30 kg. The radius of the punching die was 120 mm and the loads were applied at room temperature. The investigations established that the applied load causes the Vickers microhardness at the cross-sectional area of the plate to increase due to strain hardening. Hence, the percentage increase of the hardness due to the load was found to be directly proportional to the increase in the load. Furthermore, the tensile test results for the parent material showed that the average Ultimate Tensile Strength (UTS) for the three samples was 308 MPa while the average Yield Strength and Percentage Elongation were 227 MPa and 38 % respectively. Similarly, the UTS of the formed components increased after the deformation of the plate, as such it can be concluded that the forming loads alter the mechanical properties of the materials by improving and strengthening the material properties.
Abstract: The objective of this study was to evaluate the
distribution patterns of Cd, Zn and Hg in groundwater by geospatial
interpolation. The study was performed at Rayong province in the
eastern part of Thailand, with high agricultural and industrial
activities. Groundwater samples were collected twice a year from 31
tubewells around this area. Inductively Coupled Plasma-Atomic
Emission Spectrometer (ICP-AES) was used to measure the
concentrations of Cd, Zn, and Hg in groundwater samples. The
results demonstrated that concentrations of Cd, Zn and Hg range
from 0.000-0.297 mg/L (x = 0.021±0.033 mg/L), 0.022-33.236 mg/L
(x = 4.214±4.766 mg/L) and 0.000-0.289 mg/L (x = 0.023±0.034
mg/L), respectively. Most of the heavy metals concentrations were
exceeded groundwater quality standards as specified in the Ministry
of Natural Resources and Environment, Thailand. The trend
distribution of heavy metals were high concentrations at the
southeastern part of the area that especially vulnerable to heavy
metals and other contaminants.
Abstract: The use of technology is increasingly adopted to
support flexible learning in Higher Education institutions. The
adoption of more sophisticated technologies offers a broad range of
facilities for communication and resource sharing, thereby creating a
flexible learning environment that facilitates and even encourages
students not to physically attend classes. However this emerging
trend seems to contradict class attendance requirements within
universities, inevitably leading to a dilemma between amending
traditional regulations and creating new policies for the higher
education institutions. This study presents an investigation into
student engagement in a technology enhanced/driven flexible
environment along with its relationship to attainment. We propose an
approach to modelling engagement from different perspectives in
terms of indicators and then consider what impact these indicators
have on student academic performance. We have carried out a case
study on the relation between attendance and attainment in a flexible
environment. Although our preliminary results show attendance is
quantitatively correlated with successful student development and
learning outcomes, our results also indicate there is a cohort that did
not follow such a pattern. Nevertheless the preliminary results could
provide an insight into pilot studies in the wider deployment of new
technology to support flexible learning.
Abstract: Several optimization algorithms specifically applied to
the problem of Operation Planning of Hydrothermal Power Systems
have been developed and are used. Although providing solutions to
various problems encountered, these algorithms have some
weaknesses, difficulties in convergence, simplification of the original
formulation of the problem, or owing to the complexity of the
objective function. Thus, this paper presents the development of a
computational tool for solving optimization problem identified and to
provide the User an easy handling. Adopted as intelligent
optimization technique, Genetic Algorithms and programming
language Java. First made the modeling of the chromosomes, then
implemented the function assessment of the problem and the
operators involved, and finally the drafting of the graphical interfaces
for access to the User. The program has managed to relate a coherent
performance in problem resolution without the need for
simplification of the calculations together with the ease of
manipulating the parameters of simulation and visualization of output
results.
Abstract: Three batches of yogurts were made with soy protein
isolate (SPI) supplemented with 2% (S2), 4% (S4) or 6% (S6) of
skim milk powder (SMP). The fourth batch (control; S0) was
prepared from SPI without SMP supplementation. Lactobacillus
delbrueckii ssp. bulgaricus ATCC 11842 (Lb 11842) and
Streptococcus thermophilus ST 1342 (ST 1342) were used as the
starter culture. Biotransformation of the inactive forms, isoflavone
glycosides (IG) to biologically active forms, isoflavone aglycones
(IA), was determined during 28 d storage. The viability of both
microorganisms was significantly higher (P < 0.05) in S2, S4, and S6
than that in S0. The ratio of lactic acid/acetic acid in S0 was in the
range of 15.53 – 22.31 compared to 7.24 – 12.81 in S2, S4 and S6.
The biotransformation of IG to IA in S2, S4 and S6 was also
enhanced by 9.9 -13.3% compared to S0.
Abstract: This paper, a simple continuous conduction mode (CCM) pulse-width-modulated (PWM) controller for high power factor boost converters is introduced. The duty ratios were obtained by the comparison of a sensed signal from inductor current or switch current and a negative slope ramp carrier waveform in each switching period. Due to the proposed control requires only the inductor current or switch current sensor and the output voltage sensor, its circuit implementation was very simple. To verify the proposed control, the circuit experimentation of a 350 W boost converter with the proposed control was applied. From the results, the input current waveform was shaped to be closely sinusoidal, implying high power factor and low harmonics.
Abstract: The field of biomedical materials plays an imperative
requisite and a critical role in manufacturing a variety of biological
artificial replacements in a modern world. Recently, titanium (Ti)
materials are being used as biomaterials because of their superior
corrosion resistance and tremendous specific strength, free- allergic
problems and the greatest biocompatibility compared to other
competing biomaterials such as stainless steel, Co-Cr alloys,
ceramics, polymers, and composite materials. However, regardless of
these excellent performance properties, Implantable Ti materials have
poor shear strength and wear resistance which limited their
applications as biomaterials. Even though the wear properties of Ti
alloys has revealed some improvements, the crucial effectiveness of
biomedical Ti alloys as wear components requires a comprehensive
deep understanding of the wear reasons, mechanisms, and techniques
that can be used to improve wear behavior. This review examines
current information on the effect of thermal and thermomechanical
processing of implantable Ti materials on the long-term prosthetic
requirement which related with wear behavior. This paper focuses
mainly on the evolution, evaluation and development of effective
microstructural features that can improve wear properties of bio
grade Ti materials using thermal and thermomechanical treatments.