Abstract: Chitosan polyacrylic acid composite membranes were
prepared by a bulk polymerization method in presence of N, N'-
methylene bisacrylamide (crosslinker) and ammonium persulphate as
initiator. Membranes prepared from this copolymer in presence and
absence of Ag nanoparticles were characterized by measuring
mechanical and physical properties, water up-take and antibacterial
properties. The results obtained indicated that the prepared
membranes have antibacterial properties which increase with adding
Ag nanoparticles.
Abstract: The main idea of this work is to investigate the effect
of knitted fabrics characteristics on moisture management properties.
Wetting and transport properties of single jersey, Rib 1&1 and
English Rib fabrics made out of cotton and blended Cotton/Polyester
yarns were studied. The dynamic water sorption of fabrics was
investigated under same isothermal and terrestrial conditions at
20±2°C-65±4% by using the Moisture Management Tester (MMT)
which can be used to quantitatively measure liquid moisture transfer
in one step in a fabric in multidirections: Absorption rate, moisture
absorbing time of the fabric's inner and outer surfaces, one-way
transportation capability, the spreading/drying rate, the speed of
liquid moisture spreading on fabric's inner and outer surfaces are
measured, recorded and discussed. The results show that fabric’s
composition and knit’s structure have a significant influence on those
phenomena.
Abstract: For a rigid body sliding on a rough surface, a range of
uncertainty or non-uniqueness of solution could be found, which is
termed: Painlevé paradox. Painlevé paradox is the reason of a wide
range of bouncing motion, observed during sliding of robotic
manipulators on rough surfaces. In this research work, the existence
of the paradox zone during the sliding motion of a two-link (P-R)
robotic manipulator with a unilateral constraint is investigated.
Parametric study is performed to investigate the effect of friction,
link-length ratio, total height and link-mass ratio on the paradox zone.
Abstract: Current transformers are an integral part of power
system because it provides a proportional safe amount of current for
protection and measurement applications. However, when the power
system experiences an abnormal situation leading to huge current
flow, then this huge current is proportionally injected to the
protection and metering circuit. Since the protection and metering
equipment’s are designed to withstand only certain amount of current
with respect to time, these high currents pose a risk to man and
equipment. Therefore, during such instances, the CT saturation
characteristics have a huge influence on the safety of both man and
equipment and on the reliability of the protection and metering
system. This paper shows the effect of burden on the Accuracy Limiting
factor/ Instrument security factor of current transformers and the
change in saturation characteristics of the CT’s. The response of the
CT to varying levels of overcurrent at different connected burden will
be captured using the data acquisition software LabVIEW. Analysis
is done on the real time data gathered using LabVIEW. Variation of
current transformer saturation characteristics with changes in burden
will be discussed.
Abstract: A biosphere reserve is developed to create harmony
amongst economic development, community development, and
environmental protection, through partnership between human and
nature. Giam Siak Kecil Bukit Batu Biosphere Reserve (GSKBB BR)
in Riau Province, Indonesia, is unique in that it has peat soil
dominating the area, many springs essential for human livelihood,
high biodiversity. Furthermore, it is the only biosphere reserve
covering privately managed production forest areas. In this research, we aimed at analyzing the threat of deforestation
and forest fire, and the potential of CO2 emission at GSKBB BR. We
used Landsat image, arcView software, and ERDAS IMAGINE 8.5
Software to conduct spatial analysis of land cover and land use
changes, calculated CO2 emission based on emission potential from
each land cover and land use type, and exercised simple linear
regression to demonstrate the relation between CO2 emission
potential and deforestation. The result showed that, beside in the buffer zone and transition
area, deforestation also occurred in the core area. Spatial analysis of
land cover and land use changes from years 2010, 2012, and 2014
revealed that there were changes of land cover and land use from
natural forest and industrial plantation forest to other land use types,
such as garden, mixed garden, settlement, paddy fields, burnt areas,
and dry agricultural land. Deforestation in core area, particularly at
the Giam Siak Kecil Wildlife Reserve and Bukit Batu Wildlife
Reserve, occurred in the form of changes from natural forest in to
garden, mixed garden, shrubs, swamp shrubs, dry agricultural land,
open area, and burnt area. In the buffer zone and transition area,
changes also happened, what once swamp forest changed into garden,
mixed garden, open area, shrubs, swamp shrubs, and dry agricultural
land. Spatial analysis on land cover and land use changes indicated
that deforestation rate in the biosphere reserve from 2010 to 2014 had
reached 16 119 ha/year. Beside deforestation, threat toward the
biosphere reserve area also came from forest fire. The occurrence of forest fire in 2014 had burned 101 723 ha of the
area, in which 9 355 ha of core area, and 92 368 ha of buffer zone
and transition area. Deforestation and forest fire had increased CO2
emission as much as 24 903 855 ton/year.
Abstract: This paper considers the design of Dual Proportional-
Integral (DPI) Load Frequency Control (LFC), using gravitational
search algorithm (GSA). The design is carried out for nonlinear
hydrothermal power system where generation rate constraint (GRC)
and governor dead band are considered. Furthermore, time delays
imposed by governor-turbine, thermodynamic process, and
communication channels are investigated. GSA is utilized to search
for optimal controller parameters by minimizing a time-domain based
objective function. GSA-based DPI has been compared to Ziegler-
Nichols based PI, and Genetic Algorithm (GA) based PI controllers
in order to demonstrate the superior efficiency of the proposed
design. Simulation results are carried for a wide range of operating
conditions and system parameters variations.
Abstract: Tamil handwritten document is taken as a key source
of data to identify the writer. Tamil is a classical language which has
247 characters include compound characters, consonants, vowels and
special character. Most characters of Tamil are multifaceted in
nature. Handwriting is a unique feature of an individual. Writer may
change their handwritings according to their frame of mind and this
place a risky challenge in identifying the writer. A new
discriminative model with pooled features of handwriting is proposed
and implemented using support vector machine. It has been reported
on 100% of prediction accuracy by RBF and polynomial kernel based
classification model.
Abstract: One of the fundamental characteristics of Information
and Communication Technology (ICT) has been the ever-changing
nature of continuous release and models of ICTs with its impact on
the academic, social, and psychological benefits of its introduction in
schools. However, there seems to be a growing concern about its
negative impact on students when introduced early in schools for
teaching and learning. This study aims to design a model of child
development factors affecting the early introduction of ICTs in
schools in an attempt to improve the understanding of child
development and introduction of ICTs in schools. The proposed
model is based on a sound theoretical framework. It was designed
following a literature review of child development theories and child
development factors. The child development theoretical framework
that fitted to the best of all child development factors was then chosen
as the basis for the proposed model. This study hence found that the
Jean Piaget cognitive developmental theory is the most adequate
theoretical frameworks for modeling child development factors for
ICT introduction in schools.
Abstract: This paper addresses minimizing the makespan of the
distributed permutation flow shop scheduling problem. In this
problem, there are several parallel identical factories or flowshops
each with series of similar machines. Each job should be allocated to
one of the factories and all of the operations of the jobs should be
performed in the allocated factory. This problem has recently gained
attention and due to NP-Hard nature of the problem, metaheuristic
algorithms have been proposed to tackle it. Majority of the proposed
algorithms require large computational time which is the main
drawback. In this study, a general variable neighborhood search
algorithm (GVNS) is proposed where several time-saving schemes
have been incorporated into it. Also, the GVNS uses the sophisticated
method to change the shaking procedure or perturbation depending
on the progress of the incumbent solution to prevent stagnation of the
search. The performance of the proposed algorithm is compared to
the state-of-the-art algorithms based on standard benchmark
instances.
Abstract: This paper will discuss how we optimize our physical
verification flow in our IC Design Department having various rule
decks from multiple foundries. Our ultimate goal is to achieve faster
time to tape-out and avoid schedule delay. Currently the physical
verification runtimes and memory usage have drastically increased
with the increasing number of design rules, design complexity, and
the size of the chips to be verified. To manage design violations, we
use a number of solutions to reduce the amount of violations needed
to be checked by physical verification engineers. The most important
functions in physical verifications are DRC (design rule check), LVS
(layout vs. schematic), and XRC (extraction). Since we have a
multiple number of foundries for our design tape-outs, we need a
flow that improve the overall turnaround time and ease of use of the
physical verification process. The demand for fast turnaround time is
even more critical since the physical design is the last stage before
sending the layout to the foundries.
Abstract: The current tools for real time management of sewer
systems are based on two software tools: the software of weather
forecast and the software of hydraulic simulation. The use of the first
ones is an important cause of imprecision and uncertainty, the use of
the second requires temporal important steps of decision because of
their need in times of calculation. This way of proceeding fact that
the obtained results are generally different from those waited. The major idea of this project is to change the basic paradigm by
approaching the problem by the "automatic" face rather than by that
"hydrology". The objective is to make possible the realization of a
large number of simulations at very short times (a few seconds)
allowing to take place weather forecasts by using directly the real
time meditative pluviometric data. The aim is to reach a system
where the decision-making is realized from reliable data and where
the correction of the error is permanent. A first model of control laws was realized and tested with different
return-period rainfalls. The gains obtained in rejecting volume vary
from 19 to 100 %. The development of a new algorithm was then
used to optimize calculation time and thus to overcome the
subsequent combinatorial problem in our first approach. Finally, this
new algorithm was tested with 16- year-rainfall series. The obtained
gains are 40 % of total volume rejected to the natural environment
and of 65 % in the number of discharges.
Abstract: Present study was aimed to develop a discharge
measuring device for irrigation and laboratory channels. Experiments
were conducted on sharp edged constricted flow meters having four
types of width constrictions namely 2:1, 1.5:1, 1:1 and 90o in the
direction of flow. These devices were made of MS sheets and
installed separately in a rectangular flume. All these four devices
were tested under free and submerged flow conditions. Eight
different discharges varying from 2 lit/sec to 30 lit/sec were passed
through each device. In total around 500 observations of upstream
and downstream depths were taken in the present work. For each
discharge, free submerged and critical submergence under different
flow conditions were noted and plotted. Once the upstream and
downstream depths of flow over any of the device are known, the
discharge can be easily calculated with the help of the curves
developed for free and submerged flow conditions. The device
having contraction 2:1 is the most efficient one as it allows maximum
critical submergence.
Abstract: Main purpose of this study is to identify the impact of
government expenditure on economic growth in Asian Countries.
Consequently, main objective is to analyze whether government
expenditure causes economic growth in Asian countries vice versa
and then scrutinizing long-run equilibrium relationship exists
between them. The study completely based on secondary data. The
methodology being quantitative that includes econometrical
techniques of cointegration, panel fixed effects model and granger
causality in the context of panel data of Asian countries; Singapore,
Malaysia, Thailand, South Korea, Japan, China, Sri Lanka, India and
Bhutan with 44 observations in each country, totaling to 396
observations from 1970 to 2013. The model used is the random
effects panel OLS model. As with the above methodology, the study
found the fascinating outcome. At first, empirical findings exhibit a
momentous positive impact of government expenditure on Gross
Domestic Production in Asian region. Secondly, government
expenditure and economic growth indicate a long-run relationship in
Asian countries. In conclusion, there is a unidirectional causality
from economic growth to government expenditure and government
expenditure to economic growth in Asian countries. Hence the study
is validated that it is in line with the Keynesian theory and Wagner’s
law as well. Consequently, it can be concluded that role of
government would play a vital role in economic growth of Asian
Countries. However; if government expenditure did not figure out
with the economy’s needs it might be considerably inspiration the
economy in a negative way so that society bears the costs.
Abstract: The aims of study were investigation on chemical
composition essential oil and the effect of extract of Coronilla varia
on antimicrobial and cytotoxicity activity. The essential oils of
Coronilla varia is obtained by hydrodistillation and analyzed by
(GC/MS) for determining their chemical composition and
identification of their components. Antibacterial activity of plant
extract was determined by disc diffusion method and anticancer
activity measured by MTT assay. The major components in essential
oil were Caryophyllene Oxide (60.19%), Alphacadinol (4.13%) and
Homoadantaneca Robexylic Acid (3.31%). The extracts from
Coronilla varia had interesting activity against Proteus mirabilis in
the concentration of 700 μg/disc and did not show any activity
against Staphylococus aureus, Bacillus subtillis, Klebsiella
pneumonia and Entrobacter cloacae. The positive control,
Ampicillin, Chloramphenicol and Cenphalothin had shown zone of
inhibition resistant all bacteria. The ethanol extract of Corohilla varia
inhibited on MCF7 cell lines. IC50 0.6(mg/ml) was the optimum
concentration of extract from Coronilla varia inhibition of cell line
growth. The MCF7 cancer cell line and Proteus mirabilis were more
sensitive to Coronilla varia ethanol extract.
Abstract: Tamil handwritten document is taken as a key source of data to identify the writer. Tamil is a classical language which has 247 characters include compound characters, consonants, vowels and special character. Most characters of Tamil are multifaceted in nature. Handwriting is a unique feature of an individual. Writer may change their handwritings according to their frame of mind and this place a risky challenge in identifying the writer. A new discriminative model with pooled features of handwriting is proposed and implemented using support vector machine. It has been reported on 100% of prediction accuracy by RBF and polynomial kernel based classification model.
Abstract: Water resource systems modeling has constantly been
a challenge through history for human beings. As the innovative
methodological development is evolving alongside computer sciences
on one hand, researches are likely to confront more complex and
larger water resources systems due to new challenges regarding
increased water demands, climate change and human interventions,
socio-economic concerns, and environment protection and
sustainability. In this research, an automatic calibration scheme has
been applied on the Gilan’s large-scale water resource model using
mathematical programming. The water resource model’s calibration
is developed in order to attune unknown water return flows from
demand sites in the complex Sefidroud irrigation network and other
related areas. The calibration procedure is validated by comparing
several gauged river outflows from the system in the past with model
results. The calibration results are pleasantly reasonable presenting a
rational insight of the system. Subsequently, the unknown optimized
parameters were used in a basin-scale linear optimization model with
the ability to evaluate the system’s performance against a reduced
inflow scenario in future. Results showed an acceptable match
between predicted and observed outflows from the system at selected
hydrometric stations. Moreover, an efficient operating policy was
determined for Sefidroud dam leading to a minimum water shortage
in the reduced inflow scenario.
Abstract: Groundwater is vital to the livelihoods and health of the majority of the people, since it provides almost the entire water resource for domestic, agricultural and industrial uses. Groundwater quality comprises the physical, chemical and bacteriological qualities. The present investigation was carried out to determine the physicochemical and bacteriological quality of the ground water sources in the residential areas of Karakulam Grama Panchayath in Thiruvananthapuram district, Kerala state in India. Karakulam is located in the eastern suburbs of Thiruvananthapuram city. The major drinking water source of the residents in the study area is wells. The present study aims to assess the portability and irrigational suitability of groundwater in the study area. The water samples were collected from randomly selected dug wells and bore wells in the study area during post monsoon and pre monsoon seasons of the year 2014 after a preliminary field survey. The physical, chemical and bacteriological parameters of the water samples were analyzed following standard procedures. The concentration of heavy metals (Cd, Pb and Mn) in the acid digested water samples were determined by using an Atomic Absorption Spectrophotometer. The results showed that the pH of well water samples ranged from acidic to alkaline level. In majority of well water samples (>54 %) the iron and magnesium content were found high in both the seasons studied, and the values were above the permissible limits of WHO drinking water quality standards. Bacteriological analyses showed that 63% of the wells were contaminated with total coliforms in both the seasons studied. Irrigational suitability of groundwater was assessed by determining the chemical indices like Sodium Percentage (%Na), Sodium Adsorption Ratio (SAR), Residual Sodium Carbonate (RSC), Permeability Index (PI), and the results indicate that the well water in the study area are good for irrigation purposes. Therefore, the study reveals the degradation of drinking water quality groundwater sources in Karakulam Grama Panchayath in Thiruvananthapuram District, Keralain terms of its chemical and bacteriological characteristics, and is not potable without proper treatment. In the study, more than 1/3rdof the well water samples tested were positive for total coliforms, and the bacterial contamination may pose threat to public health. The study recommends the need for periodic well water quality monitoring in the study area and to conduct awareness programs among the residents.
Abstract: The importance of energy efficiency within the production processes increases steadily. For a comprehensive assessment of energy efficiency within the production process, unfortunately no tools exist or have been developed yet. Therefore the Institute for Factory Automation and Production Systems at the Friedrich-Alexander-University Erlangen-Nuremberg has developed two methods with the goal of achieving transparency and a quantitative assessment of energy efficiency namely EEV (Energy Efficiency Value) and EPE (Energetic Process Efficiency). This paper describes the basics and state-of-the-art as well as the developed approaches.
Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear dynamics
analysis of the structures with assuming elastic-perfectly-plastic
behavior was performed using RAM PERFORM-3D software; the
horizontal component was taken into consideration with and without
the incorporation of the corresponding vertical component. Dynamic
responses obtained for the horizontal component acting alone were
compared with those obtained from the simultaneous application of
both seismic components. The results show that the effect of the
vertical component of ground motion may increase the axial load
significantly in the interior columns and, consequently, the stories.
The plastic mechanisms would be changed. The P-Delta effect is
expected to increase. The punching base plate shear of the columns
should be considered. Moreover, the vertical component increases the
input energy when the structures exhibit inelastic behavior and are
taller.
Abstract: Fiber Reinforced Polymer (FRP) is a composite material with exceptional properties that are capable to replace conventional steel reinforcement in reinforced and pre-stressed concrete structures. However, the main obstacle for their wide use in pre-stressed concrete application is the anchorage system. Due to the weakness of FRP in the transverse direction, the pre-stressing capacity of FRP bars are limited. This paper investigates the modification of the conventional wedge anchorage system to be used for stressing of FRP bars in pre-stressed applications. Epoxy adhesive material with glass FRP (GFRP) bars and conventional steel wedge were used in this paper. The GFRP bars are encased with epoxy at the anchor zone and the wedge system was used in pull-out test. The results showed a loading capacity of 47.6 kN which is 69% of the bar ultimate capacity. Additionally, nylon wedge was made with the same dimensions of the steel wedge and tested for GFRP bars without epoxy layer. The nylon wedge showed a loading capacity of 19.7 kN which is only 28.5% of the ultimate bar capacity.