Abstract: The properties of hollow sandcrete blocks produced in
Minna, Nigeria are presented. Sandcrete block is made of cement,
water and sand binded together in certain mix proportions. For the
purpose of this work, fifty (50) commercial sandcrete block industries
were visited in Minna, Nigeria to obtain block samples and
aggregates used for the manufacture, and to take inventory of the mix
composition and the production process. Sieve analysis tests were
conduction on the soil sample from various block industries to
ascertain their quality to be used for block making. The mix ratios
were also investigated. Five (5) nine inches (9’’ or 225mm) blocks
were obtained from each block industry and tested for dimensional
compliance and compressive strength. The results of the soil test
shows that the grading fall within the limit for natural aggregate and
can easily are used to obtain workable mix. Physical examinations of
the block sizes show slight deviation from the standard requirement
in NIS 87:2000. Compressive strength of hollow sandcrete blocks in
range of 0.12 N/mm2 to 0.54 N/mm2 was obtained which is below the
recommendable value of 3.45 N/mm2 for load bearing hollow
sandcrete blocks. This indicates that these blocks are below the
standard for load-bearing sandcrete blocks and cannot be used as load
bearing walling units. The mix composition also indicated low
cement content resulting in low compressive strength. Most of the
commercial block industries visited does not take curing very serious.
Water were only sprinkled ones or twice before the blocks were
stacked and made readily available for sale. It is recommended that a
mix ratio of 1:4 to 1:6 should be used for the production of sandcrete
blocks and proper curing practice should be adhered. Blocks should
also be cured for 14 days before making them available for
consumers.
Abstract: The fuel potential of six tropical hardwood species
namely: Triplochiton scleroxylon, Ceiba pentandra, Aningeria
robusta, Terminalia superba, Celtis mildbreadii and Piptadenia
africana were studied. Properties studied included species density,
gross calorific value, volatile matter, ash content, organic carbon and
elemental composition. Fuel properties were determined using
standard laboratory methods. The result indicates that the gross
calorific value (GCV) of the species ranged from 20.16 to 22.22
MJ/kg and they slightly varied from each other. Additionally, the
GCV of the biomass materials were higher than that of other biomass
materials like; wheat straw, rice straw, maize straw and sugar cane.
The ash and volatile matter content varied from 0.6075 to 5.0407%,
and 75.23% to 83.70% respectively. The overall rating of the
properties of the six biomass materials suggested that Piptadenia
africana has the best fuel property to be used as briquettes and
Aningeria robusta the worse. This study therefore suggests that a
holistic assessment of a biomass material needs to be done before
selecting it for fuel purpose.
Abstract: This study aimed to explore the practical experience
of child welfare caseworkers and professionalism in child case
management in Malaysia. This paper discussed the specific social
work practice competency and the challenges faced by child
caseworkers in the fieldwork. This research was qualitative with
grounded theory approach. Four sessions of focused group discussion
(FGD) were conducted involving a total of 27 caseworkers (child
protector and probation officers) in the Klang Valley. The study
found that the four basic principles of knowledge in child case
management namely: 1. knowledge in child case management; 2.
professional values of caseworkers towards children; 3. skills in
managing cases; and 4. culturally competent practice in child case
management. In addition, major challenges faced by the child case
manager are the capacity and commitment of the family in children’s
rehabilitation program, the credibility of caseworkers are being
challenged, and the challenges of support system from intra and interagency.
This study is important for policy makers to take into account
the capacity and the needs of the child’s caseworker in accordance
with the national social work competency framework. It is expected
that case management services for children will improve
systematically in line with national standards.
Abstract: Natural dyes are gaining interest due their expected
low risk to human health and to the environment. In this study, the
wash fastness of a natural coloring matter from the liquid waste
produced in the steam treatment of eucalyptus wood in textile fabrics
was investigated. Specifically, eucalyptus wood extract was used to
dye cotton, nylon and wool in an exhaust dyeing process without the
addition of the traditional mordanting agents and then submitted to
wash fastness analysis. The resulting dyed fabrics were evaluated for
color fastness. It was found that wash fastness of dyed fabrics was
very good to cotton and excellent to nylon and wool.
Abstract: In this paper, relationship between different properties
of IC concrete and water cement ratio, obtained from a
comprehensive experiment conducted on IC using local materials
(Burnt clay chips- BC) is presented. In addition, saturated SAP was
used as an IC material in some cases. Relationships have been
developed through regression analysis. The focus of this analysis is
on developing relationship between a dependent variable and an
independent variable. Different percent replacements of BC and
water cement ratios were used. Compressive strength, modulus of
elasticity, water permeability and chloride permeability were tested
and variations of these parameters were analyzed with respect to
water cement ratio.
Abstract: The primary objective of this work was to study the
effect of resin chemistry, pH and molarity of binding and elution
buffer on aggregate removal using Cation Exchange Chromatography
and find the optimum conditions which can give efficient aggregate
removal with minimum loss of yield. Four different resins were used
for carrying out the experiments: Fractogel EMD SO3
-(S), Fractogel EMD COO-(M), Capto SP ImpRes and S Ceramic HyperD. Runs
were carried out on the AKTA Avant system. Design of Experiments
(DOE) was used for analysis using the JMP software. The
dependence of the yield obtained using different resins on the
operating conditions was studied. Success has been achieved in
obtaining yield greater than 90% using Capto SP ImpRes and
Fractogel EMD COO-(M) resins. It has also been found that a change
in the operating conditions generally has different effects on the
yields obtained using different resins.
Abstract: In the present paper the design of plate heat exchangers
is formulated as an optimization problem considering two
mathematical modelling. The number of plates is the objective
function to be minimized, considering implicitly some parameters
configuration. Screening is the optimization method used to solve the
problem. Thermal and hydraulic constraints are verified, not viable
solutions are discarded and the method searches for the convergence to
the optimum, case it exists. A case study is presented to test the
applicability of the developed algorithm. Results show coherency with
the literature.
Abstract: In this paper numerical studies have been carried out
to examine the pre-ignition flow features of high-performance solid
propellant rocket motors with two different port geometries but with
same propellant loading density. Numerical computations have been
carried out using a validated 3D, unsteady, 2nd-order implicit, SST k-
ω turbulence model. In the numerical study, a fully implicit finite
volume scheme of the compressible, Reynolds-Averaged, Navier-
Stokes equations is employed. We have observed from the numerical
results that in solid rocket motors with highly loaded propellants
having divergent port geometry the hot igniter gases can create preignition
pressure oscillations leading to thrust oscillations due to the
flow unsteadiness and recirculation. We have also observed that the
igniter temperature fluctuations are diminished rapidly thereby
reaching the steady state value faster in the case of solid propellant
rocket motors with convergent port than the divergent port
irrespective of the igniter total pressure. We have concluded that the
prudent selection of the port geometry, without altering the propellant
loading density, for damping the total temperature fluctuations within
the motor is a meaningful objective for the suppression and control of
instability and/or thrust oscillations often observed in solid propellant
rocket motors with non-uniform port geometry.
Abstract: The increasing volume of solid waste generated,
collected and disposed daily complicate adequate management of
solid waste by relevant agency like Niger State Environmental
Protection Agency (NISEPA). In addition, the impacts of solid waste
on the natural environment and human livelihood require
identification of cost-effective ways for sustainable municipal waste
management in Nigeria. These signal the need for identifying
environment-friendly initiative and local solution to address the
problem of municipal solid waste. A research field was secured at
Pago, Minna, Niger State which is located in the guinea savanna belt
of Nigeria, within longitude 60 361 4311 - 4511 and latitude 90 291
37.6111 - .6211 N. Poultry droppings, decomposed household waste
manure and NPK treatments were used. The experimental field was
divided into three replications and four (4) treatments on each
replication making a total of twelve (12) plots. The treatments were
allotted using Randomized Complete Block Design (RCBD) and
Data collected was analyzed using SPSS software and RCBD. The
result depicts variation in plant height and number of leaves at 50%
flowering; Poultry dropping records the highest height while the
number of leaves for waste manure competes fairly well with NPK
treatment. Similarly, the varying treatments significantly increase
vegetable yield, as the control (non-treatment) records the least yield
for the three vegetable samples. Adoption of this organic manure for
cultivation does not only enhance environment quality and attainment
of food security but will contribute to local economic development,
poverty alleviation as well as social inclusion.
Abstract: The aim of the current work was to employ the finite
element method to model a slab, with a small hole across its width,
undergoing plastic plane strain deformation. The computational
model had, however, to be validated by comparing its results with
those obtained experimentally. Since they were in good agreement,
the finite element method can therefore be considered a reliable tool
that can help gain better understanding of the mechanism of ductile
failure in structural members having stress raisers. The finite element
software used was ANSYS, and the PLANE183 element was utilized.
It is a higher order 2-D, 8-node or 6-node element with quadratic
displacement behavior. A bilinear stress-strain relationship was used
to define the material properties, with constants similar to those of the
material used in the experimental study. The model was run for
several tensile loads in order to observe the progression of the plastic
deformation region, and the stress concentration factor was
determined in each case. The experimental study involved employing the visioplasticity
technique, where a circular mesh (each circle was 0.5 mm in
diameter, with 0.05 mm line thickness) was initially printed on the
side of an aluminum slab having a small hole across its width.
Tensile loading was then applied to produce a small increment of
plastic deformation. Circles in the plastic region became ellipses,
where the directions of the principal strains and stresses coincided
with the major and minor axes of the ellipses. Next, we were able to
determine the directions of the maximum and minimum shear
stresses at the center of each ellipse, and the slip-line field was then
constructed. We were then able to determine the stress at any point in
the plastic deformation zone, and hence the stress concentration
factor. The experimental results were found to be in good agreement
with the analytical ones.
Abstract: A new design of aerostatic thrust bearing is proposed
for high static stiffness. The bearing body, which is mead of polymer
covered with metallic membrane, is held by a circular ring. Such a
support helps form a concave air gap to grasp the air pressure. The
polymer body, which can be made rapidly by either injection or
molding is able to provide extra damping under dynamic loading. The
smooth membrane not only serves as the bearing surface but also
protects the polymer body. The restrictor is a capillary inside a silicone
tube. It can passively compensate the variation of load by expanding
the capillary diameter for more air flux. In the present example, the
stiffness soars from 15.85 N/μm of typical bearing to 349.85 N/μm at
bearing elevation 9.5 μm; meanwhile the load capacity also enhances
from 346.86 N to 704.18 N.
Abstract: In this research, thorium dioxide mesoporous
nanocrystalline powder was synthesized through the sol-gel method
using hydrated thorium nitrate and ammonium hydroxide as starting
materials and Triton X100 as surfactant. ThO2 gel was characterized
by thermogravimetric (TGA), and prepared ThO2 powder was
subjected to scanning electron microscopy (SEM), X-ray diffraction
(XRD), and Brunauer-Emett-Teller (BET) analyses studies. Detailed
analyses show that prepared powder consisted of phase with the
space group Fm3m of thoria and its crystalline size was 12.6 nm. The
thoria possesses 16.7 m2/g surface area and the pore volume and size
calculated to be 0.0423 cc/g and 1.947 nm, respectively.
Abstract: Expansive soils are often encountered in many parts
of the world, especially in arid and semi-arid fields. Such kind of
soils, generally including active clay minerals in low water content,
enlarge in volume by absorbing the water through the surface and
cause a great harm to the light structures such as channel coating,
roads and airports. The expansive soils were encountered on the path
of Apa-Hotamış conveyance channel belonging to the State
Hydraulic Works in the region of Konya. In the research done in this
area, it is predicted that the soil has a swollen nature and the soil
should be filled with proper granular equipments by digging the
ground to 50-60 cm. In this study, for purpose of helping the other
research to be done in the same area, it is thought that instead of
replacing swollen soil with the granular soil, by stabilizing it with
polypropylene fiber and using it its original place decreases effect of
swelling percent, in this way the cost will be decreased. Therefore,
laboratory tests were conducted to study the effects of polypropylene
fiber on swelling characteristics of expansive soil. Test results
indicated that inclusion of fiber reduced swell percent of expansive
soil. As the fiber content increased, the unconfined compressive
strength was increased. Finally, it can be said that stabilization of
expansive soils with polypropylene fiber is an effective method.
Abstract: The objective of this study was to evaluate the
effects of calving season on the production and economic efficiency
of dairy farms in Egypt. Our study was performed at dairy
production farms in the Alexandria, Behera, and Kafr El-Sheikh
provinces of Egypt from summer 2010 to winter 2013. The
randomly selected dairy farms had herds consisting of Baladi,
Holstein-Friesian, or cross-bred (Baladi × Holstein-Friesian) cows.
The data were collected from production records and responses to a
structured questionnaire. The average total return differed
significantly (P < 0.05) between the different cattle breeds and
calving seasons. The average total return was highest for the
Holstein- Friesian cows that calved in the winter (29106.42
EGP/cow/year), and it was lowest for Baladi cows that calved in the
summer (12489.79 EGP/cow/year). Differences in total returns
between the cows that calved in the winter or summer or between
the foreign and native breeds, as well as variations in calf prices,
might have contributed to the differences in milk yield. The average
net profit per cow differed significantly (P < 0.05) between the cattle
breeds and calving seasons. The average net profit values for the
Baladi cows that calved in the winter or summer were 2413 and
2994.96 EGP/cow/year, respectively, and those for the Holstein-
Friesian cows were 10744.17 and 7860.56 EGP/cow/year,
respectively, whereas those for the cross-bred cows were 10174.86
and 7571.33 EGP/cow/year, respectively. The variations in net profit
might have resulted from variation in the availability or price of feed
materials, milk prices, or sales volumes. Our results show that the
breed and calving season of dairy cows significantly affected the
economic efficiency of dairy farms in Egypt. The cows that calved
in the winter produced more milk than those that calved in the
summer, which may have been the result of seasonal influences,
such as temperature, humidity, management practices, and the type
of feed or green fodder available.
Abstract: This paper presents the influences on the entrainment
of serpentines by grinding and reagents during copper–nickel sulfide
flotation. The previous bench flotation tests were performed to extract
the metallic values from the ore in Yunnan Mine, China and the
relatively satisfied results with recoveries of 86.92% Cu, 54.92% Ni,
and 74.73% Pt+Pd in the concentrate were harvested at their grades of
4.02%, 3.24% and 76.61 g/t, respectively. However, the content of
MgO in the concentrate was still more than 19%. Micro-flotation tests
were conducted with the objective of figuring out the influences on the
entrainment of serpentines into the concentrate by particle size,
flocculants or depressants and collectors, as well as visual
observations in suspension by OLYMPUS camera. All the tests results
pointed to the presences of both “entrapped-in” serpentines and its
coating on the hydrophobic flocs resulted from strong collectors
(combination of butyl xanthate, butyl ammonium dithophosphate,
even after adding carboxymethyl cellulose as effective depressant.
And fine grinding may escalate the entrainment of serpentines in the
concentrate.
Abstract: The main objective of MEAL is to develop a
pedagogical tool aimed to help teachers and nutritionists (students
and professionals) to acquire, train, promote and deliver to children
basic nutritional education and healthy eating behaviours
competencies. MEAL is focused on eating behaviours and not only in
nutritional literacy, and will use new technologies like Information
and Communication Technologies (ICTs) and serious games (SG)
platforms to consolidate the nutritional competences and habits.
Abstract: This work is on decision tree-based classification for
the disbursement of scholarship. Tree-based data mining
classification technique is used in other to determine the generic rule
to be used to disburse the scholarship. The system based on the
defined rules from the tree is able to determine the class (status) to
which an applicant shall belong whether Granted or Not Granted. The
applicants that fall to the class of granted denote a successful
acquirement of scholarship while those in not granted class are
unsuccessful in the scheme. An algorithm that can be used to classify
the applicants based on the rules from tree-based classification was
also developed. The tree-based classification is adopted because of its
efficiency, effectiveness, and easy to comprehend features. The
system was tested with the data of National Information Technology
Development Agency (NITDA) Abuja, a Parastatal of Federal
Ministry of Communication Technology that is mandated to develop
and regulate information technology in Nigeria. The system was
found working according to the specification. It is therefore
recommended for all scholarship disbursement organizations.
Abstract: This study presents three different approaches to
estimate bubble point pressures for the binary system of CO2 and
ethyl palmitate fatty acid ethyl ester. The first method involves the
Peng-Robinson (PR) Equation of State (EoS) with the conventional
mixing rule of Van der Waals. The second approach involves the PR
EOS together with the Wong Sandler (WS) mixing rule, coupled with
the UNIQUAC GE model. In order to model the bubble point
pressures with this approach, the volume and area parameter for ethyl
palmitate were estimated by the Hansen group contribution method.
The last method involved the Peng-Robinson, combined with the
Wong-Sandler method, but using NRTL as the GE model. Results
using the Van der Waals mixing rule clearly indicated that this
method has the largest errors among all three methods, with errors in
the range of 3.96-6.22%. The PR-WS-UNIQUAC method exhibited
small errors, with average absolute deviations between 0.95 to 1.97
percent. The PR-WS-NRTL method led to the least errors, where
average absolute deviations ranged between 0.65-1.7%.
Abstract: This study integrates a larger research empirical
project that examines second language (SL) learners’ profiles and
valid procedures to perform complete and diagnostic assessment in
schools. 102 learners of Portuguese as a SL aged 7 and 17 years
speakers of distinct home languages were assessed in several
linguistic tasks. In this article, we focused on writing performance in
the specific task of narrative essay composition. The written outputs
were measured using the score in six components adapted from an
English SL assessment context (Alberta Education): linguistic
vocabulary, grammar, syntax, strategy, socio-linguistic, and
discourse. The writing processes and strategies in Portuguese
language used by different immigrant students were analysed to
determine features and diversity of deficits on authentic texts
performed by SL writers. Differentiated performance was based on
the diversity of the following variables: grades, previous schooling,
home language, instruction in first language, and exposure to
Portuguese as Second Language. Indo-Aryan languages speakers
showed low writing scores compared to their peers and the type of
language and respective cognitive mapping (such as Mandarin and
Arabic) was the predictor, not linguistic distance. Home language
instruction should also be prominently considered in further research
to understand specificities of cognitive academic profile in a
Romance languages learning context. Additionally, this study also
examined the teachers’ representations that will be here addressed to
understand educational implications of second language teaching in
psychological distress of different minorities in schools of specific
host countries.
Abstract: Conductivity properties of DNA molecule is
investigated in a simple, but chemically specific approach that is
intimately related to the Su-Schrieffer-Heeger (SSH) model. This
model is a tight-binding linear nanoscale chain. We have tried to
study the electrical current flowing in DNA and investigated the
characteristic I-V diagram. As a result, It is shown that there are the
(quasi-) ohmic areas in I-V diagram. On the other hand, the regions
with a negative differential resistance (NDR) are detectable in
diagram.