Abstract: The present study deals with the analysis of the cylindrical part of a CNG storage vessel, combining a plastic liner and an over wrapped filament wound composite. Three kind of polymer are used in the present analysis: High density Polyethylene HDPE, Light low density Polyethylene LLDPE and finally blend of LLDPE/HDPE. The effect of the mechanical properties on the behavior of type IV vessel may be then investigated. In the present paper, the effect of the order of the circumferential winding on the stacking sequence may be then investigated. Based on mechanical considerations, the present model provides an exact solution for stresses and deformations on the cylindrical section of the vessel under thermo-mechanical static loading. The result show a good behavior of HDPE liner compared to the other plastic materials. The presence of circumferential winding angle in the stacking improves the rigidity of vessel by improving the burst pressure.
Abstract: This paper explores the opportunity of using tri-axial
wireless accelerometers for supervised monitoring of sports
movements. A motion analysis system for the upper extremities of
lawn bowlers in particular is developed. Accelerometers are placed
on parts of human body such as the chest to represent the shoulder
movements, the back to capture the trunk motion, back of the hand,
the wrist and one above the elbow, to capture arm movements. These
sensors placement are carefully designed in order to avoid restricting
bowler-s movements. Data is acquired from these sensors in soft-real
time using virtual instrumentation; the acquired data is then
conditioned and converted into required parameters for motion
regeneration. A user interface was also created to facilitate in the
acquisition of data, and broadcasting of commands to the wireless
accelerometers. All motion regeneration in this paper deals with the
motion of the human body segment in the X and Y direction, looking
into the motion of the anterior/ posterior and lateral directions
respectively.
Abstract: It is well known that during the developments in the
economic sector and through the financial crises occur everywhere in
the whole world, volatility measurement is the most important
concept in financial time series. Therefore in this paper we discuss
the volatility for Amman stocks market (Jordan) for certain period of
time. Since wavelet transform is one of the most famous filtering
methods and grows up very quickly in the last decade, we compare
this method with the traditional technique, Fast Fourier transform to
decide the best method for analyzing the volatility. The comparison
will be done on some of the statistical properties by using Matlab
program.
Abstract: By employing BS (Base Station) cooperation we can
increase substantially the spectral efficiency and capacity of cellular
systems. The signals received at each BS are sent to a central unit that
performs the separation of the different MT (Mobile Terminal) using
the same physical channel. However, we need accurate sampling and
quantization of those signals so as to reduce the backhaul
communication requirements.
In this paper we consider the optimization of the quantizers for BS
cooperation systems. Four different quantizer types are analyzed and
optimized to allow better SQNR (Signal-to-Quantization Noise
Ratio) and BER (Bit Error Rate) performance.
Abstract: The hand is one of the essential parts of the body for
carrying out Activities of Daily Living (ADLs). Individuals use their
hands and fingers in everyday activities in the both the workplace
and home. Hand-intensive tasks require diverse and sometimes
extreme levels of exertion, depending on the action, movement or
manipulation involved. The authors have undertaken several studies
looking at grip choice and comfort. It is hoped that in providing
improved understanding of discomfort during ADLs this will aid in
the design of consumer products.
Previous work by the authors outlined a methodology for
calculating pain frequency and pain level for a range of tasks. From
an online survey undertaken by the authors with regards
manipulating objects during everyday tasks, tasks involving
gripping were seen to produce the highest levels of pain and
discomfort. Questioning of the participants showed that cleaning
tasks were seen to be ADL's that produced the highest levels of
discomfort, with women feeling higher levels of discomfort than
men.
This paper looks at the methodology for calculating pain
frequency and pain level with particular regards to gripping
activities. This methodology shows that activities such as mopping,
sweeping and hoovering shows the highest numbers of pain
frequency and pain level at 3112.5 frequency per month while the
pain level per person doing this action was 0.78.The study then uses
thin-film force sensors to analyze the force distribution in the hand
whilst hoovering and compares this for differing grip styles and
genders. Women were seen to have more of their hand under a
higher pressure than men when undertaking hoovering. This
suggests that women may feel greater discomfort than men since
their hand is at a higher pressure more of the time.
Abstract: In this article, by using fuzzy AHP and TOPSIS
technique we propose a new method for project selection problem.
After reviewing four common methods of comparing alternatives
investment (net present value, rate of return, benefit cost analysis
and payback period) we use them as criteria in AHP tree. In this
methodology by utilizing improved Analytical Hierarchy Process
by Fuzzy set theory, first we try to calculate weight of each
criterion. Then by implementing TOPSIS algorithm, assessment of
projects has been done. Obtained results have been tested in a
numerical example.
Abstract: A four-lobe pressure dam bearing which is
produced by cutting two pressure dams on the upper two lobes and
two relief-tracks on the lower two lobes of an ordinary four-lobe
bearing is found to be more stable than a conventional four-lobe
bearing. In this paper a four-lobe pressure dam bearing supporting
rigid and flexible rotors is analytically investigated to determine its
performance when L/D ratio is varied in the range 0.75 to 1.5. The
static and dynamic characteristics are studied at various L/D ratios.
The results show that the stability of a four-lobe pressure dam
bearing increases with decrease in L/D ratios both for rigid as well as
flexible rotors.
Abstract: Refractive index control of benzocyclobutene (BCB 4024-40) is achieved by facilitating different conditions during the thermal curing of BCB film. Refractive index (RI) change of 1.49% is obtained with curing of BCB film using an oven, while the RI change is 0.1% when the BCB is cured using a hotplate. The two different curing methods exhibit a temperature dependent refractive index change of the BCB photosensitive polymer. By carefully controlling the curing conditions, multiple layers of BCB with different RI can be fabricated, which can then be applied in the fabrication of optical waveguides.
Abstract: The oil and gas industry has moved towards Load and
Resistance Factor Design through API RP2A - LRFD and the
recently published international standard, ISO-19902, for design of
fixed steel offshore structures. The ISO 19902 is intended to provide
a harmonized design practice that offers a balanced structural fitness
for the purpose, economy and safety. As part of an ongoing work, the
reliability analysis of tubular joints of the jacket structure has been
carried out to calibrate the load and resistance factors for the design
of offshore platforms in Malaysia, as proposed in the ISO.
Probabilistic models have been established for the load effects (wave,
wind and current) and the tubular joints strengths. In this study the
First Order Reliability Method (FORM), coded in MATLAB
Software has been employed to evaluate the reliability index of the
typical joints, designed using API RP2A - WSD and ISO 19902.
Abstract: Distributed Generation (DG) in the form of renewable
power generation systems is currently preferred for clean power
generation. It has a significant impact on the distribution systems.
This impact may be either positively or negatively depending on the
distribution system, distributed generator and load characteristics. In
this works, an overview of DG is briefly introduced. The technology
of DG is also listed while the technical impacts and economic
impacts are explained.
Abstract: A finite element analysis (FEA) computer software HyperWorks is utilized in re-designing an automotive component to reduce its mass. Reduction of components mass contributes towards environmental sustainability by saving world-s valuable metal resources and by reducing carbon emission through improved overall vehicle fuel efficiency. A shape optimization analysis was performed on a rear spindle component. Pre-processing and solving procedures were performed using HyperMesh and RADIOSS respectively. Shape variables were defined using HyperMorph. Then optimization solver OptiStruct was utilized with fatigue life set as a design constraint. Since Stress-Number of Cycle (S-N) theory deals with uni-axial stress, the Signed von Misses stress on the component was used for looking up damage on S-N curve, and Gerber criterion for mean stress corrections. The optimization analysis resulted in mass reduction of 24% of the original mass. The study proved that the adopted approach has high potential use for environmental sustainability.
Abstract: Integration of system process information obtained
through an image processing system with an evolving knowledge
database to improve the accuracy and predictability of wear particle
analysis is the main focus of the paper. The objective is to automate
intelligently the analysis process of wear particle using classification
via self organizing maps. This is achieved using relationship
measurements among corresponding attributes of various
measurements for wear particle. Finally, visualization technique is
proposed that helps the viewer in understanding and utilizing these
relationships that enable accurate diagnostics.
Abstract: Integration of system process information obtained
through an image processing system with an evolving knowledge
database to improve the accuracy and predictability of wear debris
analysis is the main focus of the paper. The objective is to automate
intelligently the analysis process of wear particle using classification
via self-organizing maps. This is achieved using relationship
measurements among corresponding attributes of various
measurements for wear debris. Finally, visualization technique is
proposed that helps the viewer in understanding and utilizing these
relationships that enable accurate diagnostics.
Abstract: Although lots of experiments have been done in enhanced oil recovery, the number of experiments which consider the effects of local and global heterogeneity on efficiency of enhanced oil recovery based on the polymer-surfactant flooding is low and rarely done. In this research, we have done numerous experiments of water flooding and polymer-surfactant flooding on a five spot glass micromodel in different conditions such as different positions of layers. In these experiments, five different micromodels with three different pore structures are designed. Three models with different layer orientation, one homogenous model and one heterogeneous model are designed. In order to import the effect of heterogeneity of porous media, three types of pore structures are distributed accidentally and with equal ratio throughout heterogeneous micromodel network according to random normal distribution. The results show that maximum EOR recovery factor will happen in a situation where the layers are orthogonal to the path of mainstream and the minimum EOR recovery factor will happen in a situation where the model is heterogeneous. This experiments show that in polymer-surfactant flooding, with increase of angles of layers the EOR recovery factor will increase and this recovery factor is strongly affected by local heterogeneity around the injection zone.
Abstract: The effect of antifungal compound from Bacillus
subtilis strain LB5 was tested against conidial germination of
Colletotrichum gloeosporioides and Pestalotiopsis eugeniae, causal
agent of anthracnose and fruit rot of wax apple, respectively.
Observation under scanning electron microscope and light compound
microscope revealed that conidial germination was completely
inhibited when treated with culture broth, culture filtrate, or crude
extract from strain LB5. Identification of purified antifungal
compound produced by strain LB5 in cell-free supernatant by nuclear
magnetic resonance and fast atom bombardment showed that the
active compound was iturin A-2.
Abstract: In this paper an attempt has been made to correlate the usefulness of electrodes made through powder metallurgy (PM) in comparison with conventional copper electrode during electric discharge machining. Experimental results are presented on electric discharge machining of AISI D2 steel in kerosene with copper tungsten (30% Cu and 70% W) tool electrode made through powder metallurgy (PM) technique and Cu electrode. An L18 (21 37) orthogonal array of Taguchi methodology was used to identify the effect of process input factors (viz. current, duty cycle and flushing pressure) on the output factors {viz. material removal rate (MRR) and surface roughness (SR)}. It was found that CuW electrode (made through PM) gives high surface finish where as the Cu electrode is better for higher material removal rate.
Abstract: In the last few years, three multivariate spectral
analysis techniques namely, Principal Component Analysis (PCA),
Independent Component Analysis (ICA) and Non-negative Matrix
Factorization (NMF) have emerged as effective tools for oscillation
detection and isolation. While the first method is used in determining
the number of oscillatory sources, the latter two methods
are used to identify source signatures by formulating the detection
problem as a source identification problem in the spectral domain.
In this paper, we present a critical drawback of the underlying linear
(mixing) model which strongly limits the ability of the associated
source separation methods to determine the number of sources
and/or identify the physical source signatures. It is shown that the
assumed mixing model is only valid if each unit of the process gives
equal weighting (all-pass filter) to all oscillatory components in its
inputs. This is in contrast to the fact that each unit, in general, acts
as a filter with non-uniform frequency response. Thus, the model
can only facilitate correct identification of a source with a single
frequency component, which is again unrealistic. To overcome
this deficiency, an iterative post-processing algorithm that correctly
identifies the physical source(s) is developed. An additional issue
with the existing methods is that they lack a procedure to pre-screen
non-oscillatory/noisy measurements which obscure the identification
of oscillatory sources. In this regard, a pre-screening procedure
is prescribed based on the notion of sparseness index to eliminate
the noisy and non-oscillatory measurements from the data set used
for analysis.
Abstract: Knowledge of patterns of genetic diversity enhances
the efficiency of germplasm conservation and improvement. In this
study 96 Iranian landraces of Triticum turgidum originating from
different geographical areas of Iran, along with 18 durum cultivars
from ten countries were evaluated for variation in morphological and
high molecular weight glutenin subunit (HMW-GS) composition.
The first two principal components clearly separated the Iranian
landraces from cultivars. Three alleles were present at the Glu-A1
locus and 11 alleles at Glu-B1. In both cultivars and landraces of
durum wheat, the null allele (Glu-A1c) was observed more
frequently than the Glu-A1a and Glu-A1b alleles. Two alleles,
namely Glu-B1a (subunit 7) and Glu-B1e (subunit 20) represented
the more frequent alleles at Glu-B1 locus. The results showed that
the evaluated Iranian landraces formed an interesting source of
favourable glutenin subunits that might be very desirable in breeding
activities for improving pasta-making quality.
Abstract: In this paper, the experimental design of using the
Taguchi method is employed to optimize the processing parameters in
the plasma arc surface hardening process. The processing parameters
evaluated are arc current, scanning velocity and carbon content of
steel. In addition, other significant effects such as the relation between
processing parameters are also investigated. An orthogonal array,
signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are
employed to investigate the effects of these processing parameters.
Through this study, not only the hardened depth increased and surface
roughness improved, but also the parameters that significantly affect
the hardening performance are identified. Experimental results are
provided to verify the effectiveness of this approach.
Abstract: The existence of maximal durations drastically modifies the performance evaluation in Discrete Event Systems (DES). The same particularity may be found on systems where the associated constraints do not concern the time. For example weight measures, in chemical industry, are used in order to control the quantity of consumed raw materials. This parameter also takes a fundamental part in the product quality as the correct transformation process is based upon a given percentage of each essence. Weight regulation therefore increases the global productivity of the system by decreasing the quantity of rejected products. In this paper we present an approach based on mixing different characteristics theories, the fuzzy system and Petri net system to describe the behaviour. An industriel application on a tobacco manufacturing plant, where the critical parameter is the weight is presented as an illustration.