Abstract: Organizations face challenges supporting knowledge
workers due to their particular requirements for an environment
supportive of their self-guided learning activities which are important
to increase their productivity and to develop creative solutions to
non-routine problems. Face-to-face knowledge sharing remains
crucial in spite of a large number of knowledge management
instruments that aim at supporting a more impersonal transfer of
knowledge. This paper first describes the main criteria for a
conceptual and technical solution targeted at flexible management of
office space that aims at assigning those knowledge workers to the
same room that are most likely to thrive when being brought together
thus enhancing their knowledge work productivity. The paper
reflects on lessons learned from the implementation and operation of
such a solution in a project-focused organization and derives several
implications for future extensions that target to foster problem
solving, informal learning and personal development.
Abstract: Heating systems are a necessity for regions which
brace extreme cold weather throughout the year. To maintain a comfortable temperature inside a given place, heating systems
making use of- Hydronic boilers- are used. The principle of a single
pipe system serves as a base for their working. It is mandatory for these heating systems to control the room temperature, thus
maintaining a warm environment. In this paper, the concept of regulation of the room temperature over a wide range is established
by using an Adaptive Fuzzy Controller (AFC). This fuzzy controller automatically detects the changes in the outside temperatures and
correspondingly maintains the inside temperature to a palatial value. Two separate AFC's are put to use to carry out this function: one to
determine the quantity of heat needed to reach the prospective temperature required and to set the desired temperature; the other to control the position of the valve, which is directly proportional to the
error between the present room temperature and the user desired temperature. The fuzzy logic controls the position of the valve as per
the requirement of the heat. The amount by which the valve opens or closes is controlled by 5 knob positions, which vary from minimum to maximum, thereby regulating the amount of heat flowing through the valve. For the given test system data, different de-fuzzifier
methods have been implemented and the results are compared. In order to validate the effectiveness of the proposed approach, a fuzzy controller has been designed by obtaining a test data from a real time
system. The simulations are performed in MATLAB and are verified with standard system data. The proposed approach can be implemented for real time applications.
Abstract: Among the most fundamental prerequisites for the successful development of electronic Government Services (e- Government) is Citizen Acceptance. Based on the UTAUT model, the paper describes a hypothetical framework that integrates the unique features of E- government to improve our understanding of the acceptance and usage of e-Government Saudi Arabia. The proposed model, based on UTAUT, includes the characteristics of Egovernment, consideration and inclusion of trust, privacy, and Saudi culture and context.
Abstract: The purpose of this work was to study the effect of the
irrigation using waste water with various electric conductivities (T(0,92ds/m), EC3 (3ds/m) and EC6 (6ds/m) on three varieties of
quinoa cultivated in a field south of Morocco. The follow up of the evolution of the chemical and agronomic parameters throughout the
culture made it possible to determine the responses to the saline stress in arid conditions. Results showed that the salinity caused the
depression of plant-s height, and reduced the fresh and dry weight in
the different parts of the three varieties plants. The increase of the irrigation water EC didn-t affect the yield for the varieties. Thus,
quinoa resisted to salinity and proved a behavior of a facultative halophyte crop. In fact, the cultivation of this using treated wastewater is feasible especially in arid areas for a sustainable use of
water resources.
Abstract: Two cultivars ('Rutuliai', 'Saint Perrie') and five
hybrids ('Tolstoi', 'Brooklyn', 'Tocayo', 'Benito', 'Tourist') of edible
tomato (Lycopersicon esculentum Mill.) were investigated at the
LRCAF Institute of Horticulture. The following fruit quality
parameters were evaluated: the amount of lycopene, β-carotene,
ascorbic acid, total and inverted sugar, sucrose, dry matter soluble
solids in fresh tomato matter, also were determined fruit skin and
flesh firmness, color indexes (CIE L*a*b*) and calculated hue angle
(h°) with chroma (C).
Abstract: Bacterial cellulose, a biopolysaccharide, is produced by the bacterium, Gluconacetobacter xylinus. Static batch fermentation for bacterial cellulose production was studied in sucrose and date syrup solutions (Bx. 10%) at 28 °C using G. xylinus (PTCC, 1734). Results showed that the maximum yields of bacterial cellulose (BC) were 4.35 and 1.69 g/l00 ml for date syrup and sucrose medium after 336 hours fermentation period, respectively. Comparison of FTIR spectrum of cellulose with BC indicated appropriate coincidence which proved that the component produced by G. xylinus was cellulose. Determination of the area under X-ray diffractometry patterns demonstrated that the crystallinity amount of cellulose (83.61%) was more than that for the BC (60.73%). The scanning electron microscopy imaging of BC and cellulose were carried out in two magnifications of 1 and 6K. Results showed that the diameter ratio of BC to cellulose was approximately 1/30 which indicated more delicacy of BC fibers relative to cellulose.
Abstract: Tanzania secondary schools in rural areas are geographically and socially isolated, hence face a number of problems in getting learning materials resulting in poor performance in National examinations. E-learning as defined to be the use of information and communication technology (ICT) for supporting the educational processes has motivated Tanzania to apply ICT in its education system. There has been effort to improve secondary school education using ICT through several projects. ICT for e-learning to Tanzania rural secondary school is one of the research projects conceived by the University of Dar-es-Salaam through its College of Engineering and Technology. The main objective of the project is to develop a tool to enable ICT support rural secondary school. The project is comprehensive with a number of components, one being development of e-learning management system (e-LMS) for Tanzania secondary schools. This paper presents strategies of developing e-LMS. It shows the importance of integrating action research methodology with the modeling methods as presented by model driven architecture (MDA) and the usefulness of Unified Modeling Language (UML) on the issue of modeling. The benefit of MDA will go along with the development based on software development life cycle (SDLC) process, from analysis and requirement phase through design and implementation stages as employed by object oriented system analysis and design approach. The paper also explains the employment of open source code reuse from open source learning platforms for the context sensitive development of the e-LMS for Tanzania secondary schools.
Abstract: Phytotoxicity of Daphne gnidium L. was evaluated
through the effect of incorporating leaves, stems and roots biomass
into soil (at 12.5, 25, 50g/Kg) and irrigation by their aqueous extracts
(50g/L), on the growth of two crops (Lactuca sativa L. and Raphanus
sativus L.) and two weeds (Peaganum harmala L. and Scolymus
maculatus L.). Results revealed a perceptible phytotoxic effect which
increased with dose and concentration. At the highest dose, roots and
leaves residues was the most toxic and caused total inhibition
respectively, for lettuce and thistle seedling growth. Irrigation with
aqueous extracts of D. gnidium different organs decreased also
seedlings length of all test species. Stems extract was more inhibitor
on thistle than peganum seedling growth; it induced a significant
reduction of 80% and 67%, for, respectively, roots and shoots.
Results of the present study suggest that different organs of D.
gnidium could be exploited in the management of agro-ecosystems.
Abstract: This research attempts to explore gaps in Information
Systems (IS) and innovation literatures by developing a model of
Information Technology (IT) capability in enabling innovation. The
research was conducted by using semi-structured interview with six
innovators in business consulting, financial, healthcare and academic
organizations. The interview results suggest four elements of ITenabled
innovation capability which are information (ability to
capture ideas and knowledge), connectivity (ability to bridge
geographical boundary and mobilize human resources),
communication (ability to attain and engage relationships between
human resources) and transformation (ability to change the functions
and process integrations) in defining IT-enabled innovation platform.
The results also suggests innovators- roles and IT capability.
Abstract: In this work, are discussed two formulations of the boundary element method - BEM to perform linear bending analysis of plates reinforced by beams. Both formulations are based on the Kirchhoff's hypothesis and they are obtained from the reciprocity theorem applied to zoned plates, where each sub-region defines a beam or a slab. In the first model the problem values are defined along the interfaces and the external boundary. Then, in order to reduce the number of degrees of freedom kinematics hypothesis are assumed along the beam cross section, leading to a second formulation where the collocation points are defined along the beam skeleton, instead of being placed on interfaces. On these formulations no approximation of the generalized forces along the interface is required. Moreover, compatibility and equilibrium conditions along the interface are automatically imposed by the integral equation. Thus, these formulations require less approximation and the total number of the degree s of freedom is reduced. In the numerical examples are discussed the differences between these two BEM formulations, comparing as well the results to a well-known finite element code.
Abstract: The paper presents an investigation in to the effect of neural network predictive control of UPFC on the transient stability performance of a multimachine power system. The proposed controller consists of a neural network model of the test system. This model is used to predict the future control inputs using the damped Gauss-Newton method which employs ‘backtracking’ as the line search method for step selection. The benchmark 2 area, 4 machine system that mimics the behavior of large power systems is taken as the test system for the study and is subjected to three phase short circuit faults at different locations over a wide range of operating conditions. The simulation results clearly establish the robustness of the proposed controller to the fault location, an increase in the critical clearing time for the circuit breakers, and an improved damping of the power oscillations as compared to the conventional PI controller.
Abstract: Developing an accurate classifier for high dimensional microarray datasets is a challenging task due to availability of small sample size. Therefore, it is important to determine a set of relevant genes that classify the data well. Traditionally, gene selection method often selects the top ranked genes according to their discriminatory power. Often these genes are correlated with each other resulting in redundancy. In this paper, we have proposed a hybrid method using feature ranking and wrapper method (Genetic Algorithm with multiclass SVM) to identify a set of relevant genes that classify the data more accurately. A new fitness function for genetic algorithm is defined that focuses on selecting the smallest set of genes that provides maximum accuracy. Experiments have been carried on four well-known datasets1. The proposed method provides better results in comparison to the results found in the literature in terms of both classification accuracy and number of genes selected.
Abstract: Water vapour transport properties of gypsum block
are studied in dependence on relative humidity using inverse analysis
based on genetic algorithm. The computational inverse analysis is
performed for the relative humidity profiles measured along the
longitudinal axis of a rod sample. Within the performed transient
experiment, the studied sample is exposed to two environments with
different relative humidity, whereas the temperature is kept constant.
For the basic gypsum characterisation and for the assessment of input
material parameters necessary for computational application of
genetic algorithm, the basic material properties of gypsum are
measured as well as its thermal and water vapour storage parameters.
On the basis of application of genetic algorithm, the relative
humidity dependent water vapour diffusion coefficient and water
vapour diffusion resistance factor are calculated.
Abstract: The objectives were to identify cyanide-degrading
bacteria and study cyanide removal efficiency. Agrobacterium
tumefaciens SUTS 1 was isolated. This is a new strain of
microorganisms for cyanide degradation. The maximum growth rate
of SUTS 1 obtained 4.7 × 108 CFU/ml within 4 days. The cyanide
removal efficiency was studied at 25, 50, and 150 mg/L cyanide. The
residual cyanide, ammonia, nitrate, nitrite, pH, and cell counts were
analyzed. At 25 and 50 mg/L cyanide, SUTS 1 obtained similar
removal efficiency approximately 87.50%. At 150 mg/L cyanide,
SUTS 1 enhanced the cyanide removal efficiency up to 97.90%. Cell
counts of SUTS 1 increased when the cyanide concentration was set
at lower. The ammonia increased when the removal efficiency
increased. The nitrate increased when the ammonia decreased but the
nitrite did not detect in all experiments. pH values also increased
when the cyanide concentrations were set at higher.
Abstract: Three dimensional simulations are carried out to estimate the effect of wind direction, wind speed and geometry on the flow and dispersion of vehicular pollutant in a street canyon. The pollutant sources are motor vehicles passing between the two buildings. Suitable emission factors for petrol and diesel vehicles at varying vehicle speed are used for the estimation of the rate of emission from the streets. The dispersion of automobile pollutant released from the street is simulated by introducing vehicular emission source term as a fixed-flux boundary condition at the ground level over the road. The emission source term is suitably calculated by adopting emission factors from literature for varying conditions of street traffic. It is observed that increase in wind angle disturbs the symmetric pattern of pollution distribution along the street length. The concentration increases in the far end of the street as compared to the near end.
Abstract: Wind energy has been shown to be one of the most
viable sources of renewable energy. With current technology, the low
cost of wind energy is competitive with more conventional sources of
energy such as coal. Most blades available for commercial grade
wind turbines incorporate a straight span-wise profile and airfoil
shaped cross sections. These blades are found to be very efficient at
lower wind speeds in comparison to the potential energy that can be
extracted. However as the oncoming wind speed increases the
efficiency of the blades decreases as they approach a stall point. This
paper explores the possibility of increasing the efficiency of the
blades at higher wind speeds while maintaining efficiency at the
lower wind speeds. The design intends to maintain efficiency at
lower wind speeds by selecting the appropriate orientation and size
of the airfoil cross sections based on a low oncoming wind speed and
given constant rotation rate. The blades will be made more efficient
at higher wind speeds by implementing a swept blade profile.
Performance was investigated using the computational fluid
dynamics (CFD).
Abstract: Product Lead Time (PLT) is the period of time from
receiving a customer's order to delivering the final product. PLT is an
indicator of the manufacturing controllability, efficiency and
performance. Due to the explosion in the rate of technological
innovations and the rapid changes in the nature of manufacturing
processes, manufacturing firms can bring the new products to market
quicker only if they can reduce their PLT and speed up the rate at
which they can design, plan, control, and manufacture. Although
there is a substantial body of research on manufacturing relating to
cost and quality issues, there is no much specific research conducted
in relation to the formulation of PLT, despite its significance and
importance. This paper analyzes and formulates PLT which can be
used as a guideline for achieving the shorter PLT. Further more this
paper identifies the causes of delay and factors that contributes to the
increased product lead-time.
Abstract: The nanosized polymeric micelles release the drug
due to acoustic cavitation, which is enhanced in dual frequency
ultrasonic fields. In this study, adult female Balb/C mice were
transplanted with spontaneous breast adenocarcinoma tumors and
were injected with a dose of 1.3 mg/kg doxorubicin in one of three
forms: free doxorubicin, micellar doxorubicin without sonication and
micellar doxorubicin with sonication. To increase cavitation yield,
the tumor region was sonicated with low level dual frequency of 3
MHz and 28 kHz. The animals were sacrificed 24 h after injection,
and their tumor, heart, spleen, liver, kidneys and plasma were
separated and homogenized. The drug content in their tumor, heart,
spleen, liver, kidneys and plasma was determined using tissue
fluorimetry. The results show that in the group that received micellar
doxorubicin with sonication, the drug concentration in the tumor
tissue was nine and three times higher than in the free doxorubicin
group and the micellar doxorubicin without sonication group,
respectively. In the micellar doxorubicin with sonication group, the
drug concentration in other tissues was lower than other groups
(p
Abstract: Knowledge modelling, a main activity for the development of Knowledge Based Systems, have no set standards and are mostly done in an ad hoc way. There is a lack of support for the transition from abstract level to implementation. In this paper, a methodology for the development of the knowledge model, which is inspired by both Software and Knowledge Engineering, is proposed. Use of UML which is the de-facto standard for modelling in the software engineering arena is explored for knowledge modelling. The methodology proposed, is used to develop a knowledge model of a knowledge based system for recommending suitable hotels for tourists visiting Mauritius.