Abstract: Sedimentation formation is a complex hydraulic phenomenon that has emerged as a major operational and maintenance consideration in modern hydraulic engineering in general and river engineering in particular. Sediments accumulation along the river course and their eventual storage in a form of islands affect water intake in the canal systems that are fed by the storage reservoirs. Without proper management, sediment transport can lead to major operational challenges in water distribution system of arid regions like the Dez and Hamidieh command areas. The paper aims to investigate sedimentation in the Western Canal of Dez Diversion Weir using the SHARC model and compare the results with the two intake structures of the Hamidieh dam in Iran using SSIIM model. The objective was to identify the factors which influence the process, check reliability of outcome and provide ways in which to mitigate the implications on operation and maintenance of the structures. Results estimated sand and silt bed loads concentrations to be 193 ppm and 827ppm respectively. This followed ,ore or less similar pattern in Hamidieh where the sediment formation impeded water intake in the canal system. Given the available data on average annual bed loads and average suspended sediment loads of 165ppm and 837ppm in the Dez, there was a significant statistical difference (16%) between the sand grains, whereas no significant difference (1.2%) was find in the silt grain sizes. One explanation for such finding being that along the 6 Km river course there was considerable meandering effects which explains recent shift in the hydraulic behavior along the stream course under investigation. The sand concentration in downstream relative to present state of the canal showed a steep descending curve. Sediment trapping on the other hand indicated a steep ascending curve. These occurred because the diversion weir was not considered in the simulation model. The comparative study showed very close similarities in the results which explains the fact that both software can be used as accurate and reliable analytical tools for simulation of the sedimentation in hydraulic engineering.
Abstract: Information Technology (IT) projects are always
accompanied by various risks and because of high rate of failure in
such projects, managing risks in order to neutralize or at least
decrease their effects on the success of the project is strongly
essential. In this paper, fuzzy analytical hierarchy process (FAHP) is
exploited as a means of risk evaluation methodology to prioritize and
organize risk factors faced in IT projects. A real case of IT projects, a
project of design and implementation of an integrated information
system in a vehicle producing company in Iran is studied. Related
risk factors are identified and then expert qualitative judgments about
these factors are acquired. Translating these judgments to fuzzy
numbers and using them as an input to FAHP, risk factors are then
ranked and prioritized by FAHP in order to make project managers
aware of more important risks and enable them to adopt suitable
measures to deal with these highly devastative risks.
Abstract: Anaerobic treatment has many advantages over other
biological method particularly when used to treat complex
wastewater such as petroleum refinery wastewater. In this study two
Up-flow Anaerobic Sludge Blanket (UASB) reactors were operated
in parallel to treat six volumetric organic loads (0.58, 1.21, 0.89,
2.34, 1.47 and 4.14 kg COD/m3·d) to evaluate the chemical oxygen
demand (COD) removal efficiency. The reactors were continuously
adapting to the changing of operation condition with increase in the
removal efficiency or slight decrease until the last load which was
more than two times the load, at which the reactor stressed and the
removal efficiency decreased to 75% with effluent concentration of
1746 mg COD/L. Other parameters were also monitored such as pH,
alkalinity, volatile fatty acid and gas production rate. The UASB
reactor was suitable to treat petroleum refinery wastewater and the
highest COD removal rate was 83% at 1215 kg/m3·d with COD
concentration about 356 mg/L in the effluent.
Abstract: Dextran is a D-glucose polymer which is produced by
Leuconostoc mesenteroides grown in a sucrose-rich media. The
organism was obtained from the Persian Type Culture Collection
(PTCC) and was transferred in MRS broth medium at 30°C and pH
6.8 for 24 h. After preparation of inoculums, organisms were
inoculated into five liquid fermentation media containing either
molasses or cheese whey or different combinations of cheese whey
and molasses. After certain fermentation period, the produced
dextran was separated and dried. Dextran yield was calculated and
significant differences in different media were observed.
Furthermore, FT-IR analysis was performed and the results showed
that there were no significant differences in the produced dextran
structures.
Abstract: High Pressure Raman scattering measurements of KDP:Mn were performed at room temperatures. The X-ray powder diffraction patterns taken at room temperature by Rietveld refinement showed that doped samples of KDP-Mn have the same tetragonal structure of a pure KDP crystal, but with a contraction of the crystalline cell. The behavior of the Raman spectra, in particular the emergence of a new modes at 330 cm-1, indicates that KDP:Mn undergoes a structural phase transition with onset at around 4 GP. First principle density-functional theory (DFT) calculations indicate that tetrahedral rotation with pressure is predominantly around the c crystalline direction. Theoretical results indicates that pressure induced tetrahedral rotations leads to change tetrahedral neighborhood, activating librations/bending modes observed for high pressure phase of KDP:Mn with stronger Raman activity.
Abstract: Applying corona wind as a novel technique can lead
to a great level of heat and mass transfer augmentation by using very
small amount of energy. Enhancement of forced flow evaporation
rate by applying electric field (corona wind) has been experimentally
evaluated in this study. Corona wind produced by a fine wire
electrode which is charged with positive high DC voltage impinges
to water surface and leads to evaporation enhancement by disturbing
the saturated air layer over water surface. The study was focused on
the effect of corona wind velocity, electrode spacing and air flow
velocity on the level of evaporation enhancement. Two sets of
experiments, i.e. with and without electric field, have been
conducted. Data obtained from the first experiment were used as
reference for evaluation of evaporation enhancement at the presence
of electric field. Applied voltages ranged from corona threshold
voltage to spark over voltage at 1 kV increments. The results showed
that corona wind has great enhancement effect on water evaporation
rate, but its effectiveness gradually diminishes by increasing air flow
velocity. Maximum enhancements were 7.3 and 3.6 for air velocities
of 0.125 and 1.75 m/s, respectively.
Abstract: In this study, the kinetics of osmotic dehydration of melons (Tille variety) in a ternary system followed by air-drying for preserving melons in the summer to be used in the winter were investigated. The effect of different osmotic solution concentrations 30, 40 and 50% (w/w) of sucrose with 10% NaCl salt and fruit to solution ratios 1:4, 1:5 and 1:6 on the mass transfer kinetics during osmotic dehydration of melon in ternary solution namely sucrosesalt- water followed by air-drying were studied. The diffusivity of water during air-drying was enhanced after the fruit samples were immersed in the osmotic solution after 60 min. Samples non-treated and pre-treated during one hour in osmotic solutions with 60% (w/w) of sucrose with 10% NaCl salt and fruit to solution ratio of 1:4 were dried in a hot air-dryer at 60oC (2 m/s) until equilibrium was achieved.
Abstract: Recently, distributed generation technologies have received much attention for the potential energy savings and reliability assurances that might be achieved as a result of their widespread adoption. Fueling the attention have been the possibilities of international agreements to reduce greenhouse gas emissions, electricity sector restructuring, high power reliability requirements for certain activities, and concern about easing transmission and distribution capacity bottlenecks and congestion. So it is necessary that impact of these kinds of generators on distribution feeder reconfiguration would be investigated. This paper presents an approach for distribution reconfiguration considering Distributed Generators (DGs). The objective function is summation of electrical power losses A Tabu search optimization is used to solve the optimal operation problem. The approach is tested on a real distribution feeder.
Abstract: In this paper the performance of unified power flow
controller is investigated in controlling the flow of po wer over the
transmission line. Voltage sources model is utilized to study the
behaviour of the UPFC in regulating the active, reactive power and
voltage profile. This model is incorporated in Newton Raphson
algorithm for load flow studies. Simultaneous method is employed
in which equations of UPFC and the power balance equations of
network are combined in to one set of non-linear algebraic equations.
It is solved according to the Newton raphson algorithm. Case studies
are carried on standard 5 bus network. Simulation is done in Matlab.
The result of network with and without using UPFC are compared in
terms of active and reactive power flows in the line and active and
reactive power flows at the bus to analyze the performance of UPFC.
Abstract: Motor imagery classification provides an important basis for designing Brain Machine Interfaces [BMI]. A BMI captures and decodes brain EEG signals and transforms human thought into actions. The ability of an individual to control his EEG through imaginary mental tasks enables him to control devices through the BMI. This paper presents a method to design a four state BMI using EEG signals recorded from the C3 and C4 locations. Principle features extracted through principle component analysis of the segmented EEG are analyzed using two novel classification algorithms using Elman recurrent neural network and functional link neural network. Performance of both classifiers is evaluated using a particle swarm optimization training algorithm; results are also compared with the conventional back propagation training algorithm. EEG motor imagery recorded from two subjects is used in the offline analysis. From overall classification performance it is observed that the BP algorithm has higher average classification of 93.5%, while the PSO algorithm has better training time and maximum classification. The proposed methods promises to provide a useful alternative general procedure for motor imagery classification
Abstract: A new code for spectral-amplitude coding optical
code-division multiple-access system is proposed called Random
diagonal (RD) code. This code is constructed using code segment and
data segment. One of the important properties of this code is that the
cross correlation at data segment is always zero, which means that
Phase Intensity Induced Noise (PIIN) is reduced. For the performance
analysis, the effects of phase-induced intensity noise, shot noise, and
thermal noise are considered simultaneously. Bit-error rate (BER)
performance is compared with Hadamard and Modified Frequency
Hopping (MFH) codes. It is shown that the system using this new
code matrices not only suppress PIIN, but also allows larger number
of active users compare with other codes. Simulation results shown
that using point to point transmission with three encoded channels,
RD code has better BER performance than other codes, also its found
that at 0 dbm PIIN noise are 10-10 and 10-11 for RD and MFH
respectively.
Abstract: The steady-state operation of maintaining voltage
stability is done by switching various controllers scattered all over
the power network. When a contingency occurs, whether forced or
unforced, the dispatcher is to alleviate the problem in a minimum
time, cost, and effort. Persistent problem may lead to blackout. The
dispatcher is to have the appropriate switching of controllers in terms
of type, location, and size to remove the contingency and maintain
voltage stability. Wrong switching may worsen the problem and that
may lead to blackout. This work proposed and used a Fuzzy CMeans
Clustering (FCMC) to assist the dispatcher in the decision
making. The FCMC is used in the static voltage stability to map
instantaneously a contingency to a set of controllers where the types,
locations, and amount of switching are induced.
Abstract: Vibration of thin cylindrical shells made of a
functionally gradient material composed of stainless steel and nickel
is presented. The effects of the FGM configuration are studied by
studying the frequencies of FG cylindrical shells. In this case FG
cylindrical shell has Nickel on its outer surface and stainless steel on
its inner surface. The study is carried out based on third order shear
deformation shell theory. The objective is to study the natural
frequencies, the influence of constituent volume fractions and the
effects of configurations of the constituent materials on the
frequencies. The properties are graded in the thickness direction
according to the volume fraction power-law distribution. Results are
presented on the frequency characteristics, the influence of the
constituent various volume fractions on the frequencies.
Abstract: The main aim of Supply Chain Management (SCM) is
to produce, distribute, logistics and deliver goods and equipment in
right location, right time, right amount to satisfy costumers, with
minimum time and cost waste. So implementing techniques that
reduce project time and cost, and improve productivity and
performance is very important. Emerging technologies such as the
Radio Frequency Identification (RFID) are now making it possible to
automate supply chains in a real time manner and making them more
efficient than the simple supply chain of the past for tracing and
monitoring goods and products and capturing data on movements of
goods and other events. This paper considers concepts, components
and RFID technology characteristics by concentration of warehouse
and inventories management. Additionally, utilization of RFID in the
role of improving information management in supply chain is
discussed. Finally, the facts of installation and this technology-s
results in direction with warehouse and inventory management and
business development will be presented.
Abstract: This paper describes the speed sensorless vector control method of the parallel connected induction motor drive fed by a single inverter. Speed and rotor fluxes of the induction motor are estimated by natural observer with load torque adaptation and adaptive rotor flux observer. The performance parameters speed and rotor fluxes are estimated from the measured terminal voltages and currents. Fourth order induction motor model is used and speed is considered as a parameter. The performance of the natural observer is similar to the conventional observer. The speed of an induction motor is estimated by MATLAB simulation under different speed and load conditions. Estimated values along with other measured states are used for closed loop control. The simulation results show that the natural observer is also effective for parallel connected induction motor drive.
Abstract: In this paper a study on the vibration of thin
cylindrical shells with ring supports and made of functionally graded
materials (FGMs) composed of stainless steel and nickel is presented.
Material properties vary along the thickness direction of the shell
according to volume fraction power law. The cylindrical shells have
ring supports which are arbitrarily placed along the shell and impose
zero lateral deflections. The study is carried out based on third order
shear deformation shell theory (T.S.D.T). The analysis is carried out
using Hamilton-s principle. The governing equations of motion of
FGM cylindrical shells are derived based on shear deformation
theory. Results are presented on the frequency characteristics,
influence of ring support position and the influence of boundary
conditions. The present analysis is validated by comparing results
with those available in the literature.
Abstract: Bridges are one of the main components of
transportation networks. They should be functional before and after
earthquake for emergency services. Therefore we need to assess
seismic performance of bridges under different seismic loadings.
Fragility curve is one of the popular tools in seismic evaluations. The
fragility curves are conditional probability statements, which give the
probability of a bridge reaching or exceeding a particular damage
level for a given intensity level. In this study, the seismic
performance of a two-span simply supported concrete bridge is
assessed. Due to usual lack of empirical data, the analytical fragility
curve was developed by results of the dynamic analysis of bridge
subjected to the different time histories in near-fault area.
Abstract: This paper gives an overview of how an OWL
ontology has been created to represent template knowledge models
defined in CML that are provided by CommonKADS.
CommonKADS is a mature knowledge engineering methodology
which proposes the use of template knowledge model for knowledge
modelling. The aim of developing this ontology is to present the
template knowledge model in a knowledge representation language
that can be easily understood and shared in the knowledge
engineering community. Hence OWL is used as it has become a
standard for ontology and also it already has user friendly tools for
viewing and editing.
Abstract: With the fast evolution of digital data exchange, security information becomes much important in data storage and transmission. Due to the increasing use of images in industrial process, it is essential to protect the confidential image data from unauthorized access. In this paper, we analyze the Advanced Encryption Standard (AES), and we add a key stream generator (A5/1, W7) to AES to ensure improving the encryption performance; mainly for images characterised by reduced entropy. The implementation of both techniques has been realized for experimental purposes. Detailed results in terms of security analysis and implementation are given. Comparative study with traditional encryption algorithms is shown the superiority of the modified algorithm.
Abstract: We board the problem of creating a seismic alert
system, based upon artificial neural networks, trained by using the
well-known back-propagation and genetic algorithms, in order to emit
the alarm for the population located into a specific city, about an
eminent earthquake greater than 4.5 Richter degrees, and avoiding
disasters and human loses. In lieu of using the propagation wave, we
employed the magnitude of the earthquake, to establish a correlation
between the recorded magnitudes from a controlled area and the city,
where we want to emit the alarm. To measure the accuracy of the
posed method, we use a database provided by CIRES, which contains
the records of 2500 quakes incoming from the State of Guerrero
and Mexico City. Particularly, we performed the proposed method to
generate an issue warning in Mexico City, employing the magnitudes
recorded in the State of Guerrero.