Abstract: The main objective of this study was to remove and recover Ni, Cu and Fe from a mixed metal system using sodium hypophosphite as a reducing agent and nickel powder as seeding material. The metal systems studied consisted of Ni-Cu, Ni-Fe and Ni-Cu-Fe solutions. A 5 L batch reactor was used to conduct experiments where 100 mg/l of each respective metal was used. It was found that the metals were reduced to their elemental form with removal efficiencies of over 80%. The removal efficiency decreased in the order Fe>Ni>Cu. The metal powder obtained contained between 97-99% Ni and was almost spherical and porous. Size enlargement by aggregation was the dominant particulate process.
Abstract: Safer driver behavior promoting is the main goal of this paper. It is a fact that drivers behavior is relatively safer when being monitored. Thus, in this paper, we propose a monitoring system to report specific driving event as well as the potentially aggressive events for estimation of the driving performance. Our driving monitoring system is composed of two parts. The first part is the in-vehicle embedded system which is composed of a GPS receiver, a two-axis accelerometer, radar sensor, OBD interface, and GPRS modem. The design considerations that led to this architecture is described in this paper. The second part is a web server where an adaptive hierarchical fuzzy system is proposed to classify the driving performance based on the data that is sent by the in-vehicle embedded system and the data that is provided by the geographical information system (GIS). Our system is robust, inexpensive and small enough to fit inside a vehicle without distracting the driver.
Abstract: This research was conducted to determine responses
of chickpeas to drought in different periods (early period, late period,
no-irrigation, two times irrigation as control). The trial was made in
“Randomized Complete Block Design" with three replications on
2010 and 2011 years in Konya-Turkey. Genotypes were consisted
from 7 lines of ICARDA, 2 certified lines and 1 local population. The
results showed that; as means of years and genotypes, early period
stress showed highest (207.47 kg da-1) seed yield and it was followed
by control (202.33 kg da-1), late period (144.64 kg da-1) and normal
(106.93 kg da-1) stress applications. The genotypes were affected too
much by drought and, the lowest seed was taken from non-irrigated
plots. As the means of years and stress applications, the highest
(196.01 kg da-1) yield was taken from genotype 22255. The reason of
yield variation could be derived from different responses of
genotypes to drought.
Abstract: An acyclic coloring of a graph G is a coloring of its
vertices such that:(i) no two neighbors in G are assigned the same
color and (ii) no bicolored cycle can exist in G. The acyclic chromatic
number of G is the least number of colors necessary to acyclically
color G. Recently it has been proved that any graph of maximum
degree 5 has an acyclic chromatic number at most 8. In this paper
we present another proof for this result.
Abstract: The mechanical properties of blends consisting of
plasticized poly(vinyl butyral) (PVB) and plasticized poly(vinyl
chloride) (PVC) are studied, in order to evaluate the possibility of
using recycled PVB waste derived from windshields. PVC was
plasticized with 38% of diisononyl phthalate (DINP), while PVB was
plasticized with 28% of triethylene glycol, bis(2-ethylhexanoate)
(3GO). The optimal process conditions for the PVB/PVC blend in 1:1
ratio were determined. Entropy was used in order to theoretically
predict the blends miscibility. The PVB content of each blend
composition used was ranging from zero to 100%. Tensile strength
and strain were tested. In addition, a comparison between recycled
and original PVB, used as constituents of the blend, was performed.
Abstract: In this paper, a new approach for quality assessment
tasks in lossy compressed digital video is proposed. The research
activity is based on the visual fixation data recorded by an eye
tracker. The method involved both a new paradigm for subjective
quality evaluation and the subsequent statistical analysis to match
subjective scores provided by the observer to the data obtained from
the eye tracker experiments. The study brings improvements to the
state of the art, as it solves some problems highlighted in literature.
The experiments prove that data obtained from an eye tracker can be
used to classify videos according to the level of impairment due to
compression. The paper presents the methodology, the experimental
results and their interpretation. Conclusions suggest that the eye
tracker can be useful in quality assessment, if data are collected and
analyzed in a proper way.
Abstract: The focus of this paper is to highlight the design and
development of an educational game prototype as an evaluation
instrument for the Malaysia driving license static test. This
educational game brings gaming technology into the conventional
objective static test to make it more effective, real and interesting.
From the feeling of realistic, the future driver can learn something,
memorized and use it in the real life. The current online objective
static test only make the user memorized the answer without knowing
and understand the true purpose of the question. Therefore, in real
life, they will not behave as expected due to behavior and moral
lacking. This prototype has been developed inform of multiple-choice
questions integrated with 3D gaming environment to make it simulate
the real environment and scenarios. Based on the testing conducted,
the respondent agrees with the use of this game prototype it can
increase understanding and promote obligation towards traffic rules.
Abstract: In this paper, a neural network tuned fuzzy controller
is proposed for controlling Multi-Input Multi-Output (MIMO)
systems. For the convenience of analysis, the structure of MIMO
fuzzy controller is divided into single input single-output (SISO)
controllers for controlling each degree of freedom. Secondly,
according to the characteristics of the system-s dynamics coupling, an
appropriate coupling fuzzy controller is incorporated to improve the
performance. The simulation analysis on a two-level mass–spring
MIMO vibration system is carried out and results show the
effectiveness of the proposed fuzzy controller. The performance
though improved, the computational time and memory used is
comparatively higher, because it has four fuzzy reasoning blocks and
number may increase in case of other MIMO system. Then a fuzzy
neural network is designed from a set of input-output training data to
reduce the computing burden during implementation. This control
strategy can not only simplify the implementation problem of fuzzy
control, but also reduce computational time and consume less
memory.
Abstract: Scheduling algorithms are used in operating systems
to optimize the usage of processors. One of the most efficient
algorithms for scheduling is Multi-Layer Feedback Queue (MLFQ)
algorithm which uses several queues with different quanta. The most
important weakness of this method is the inability to define the
optimized the number of the queues and quantum of each queue. This
weakness has been improved in IMLFQ scheduling algorithm.
Number of the queues and quantum of each queue affect the response
time directly. In this paper, we review the IMLFQ algorithm for
solving these problems and minimizing the response time. In this
algorithm Recurrent Neural Network has been utilized to find both
the number of queues and the optimized quantum of each queue.
Also in order to prevent any probable faults in processes' response
time computation, a new fault tolerant approach has been presented.
In this approach we use combinational software redundancy to
prevent the any probable faults. The experimental results show that
using the IMLFQ algorithm results in better response time in
comparison with other scheduling algorithms also by using fault
tolerant mechanism we improve IMLFQ performance.
Abstract: A stiffened laminated composite panel (1 m length ×
0.5m width) was optimized for minimum weight and deflection under
several constraints using genetic algorithm. Here, a significant study
on the performance of a penalty function with two kinds of static and
dynamic penalty factors was conducted. The results have shown that
linear dynamic penalty factors are more effective than the static ones.
Also, a specially combined linear-exponential function has shown to
perform more effective than the previously mentioned penalty
functions. This was then resulted in the less sensitivity of the GA to
the amount of penalty factor.
Abstract: The purpose of our study was to compare spontaneous
re-epithelisation characteristics versus assisted re-epithelisation. In
order to assess re-epithelisation of the injured skin, we have imagined
and designed a burn wound model on Wistar rat skin. Our aim was to
create standardised, easy reproducible and quantifiable skin lesions
involving entire epidermis and superficial dermis. We then have
applied the above mentioned therapeutic strategies to compare
regeneration of epidermis and dermis, local and systemic parameter
changes in different conditions. We have enhanced the reepithelisation
process under a moist atmosphere of a polyurethane
wound dress modified with helium non-thermal plasma, and with the
aid of direct cold-plasma treatment respectively. We have followed
systemic parameters change: hematologic and biochemical
parameters, and local features: oxidative stress markers and histology
of skin in the above mentioned conditions. Re-epithelisation is just a
part of the skin regeneration process, which recruits cellular
components, with the aid of epidermal and dermal interaction via
signal molecules.
Abstract: This paper presents a method to estimate load profile
in a multiple power flow solutions for every minutes in 24 hours per
day. A method to calculate multiple solutions of non linear profile is
introduced. The Power System Simulation/Engineering (PSS®E) and
python has been used to solve the load power flow. The result of this
power flow solutions has been used to estimate the load profiles for
each load at buses using Independent Component Analysis (ICA)
without any knowledge of parameter and network topology of the
systems. The proposed algorithm is tested with IEEE 69 test bus
system represents for distribution part and the method of ICA has
been programmed in MATLAB R2012b version. Simulation results
and errors of estimations are discussed in this paper.
Abstract: Stochastic models of biological networks are well established in systems biology, where the computational treatment of such models is often focused on the solution of the so-called chemical master equation via stochastic simulation algorithms. In contrast to this, the development of storage-efficient model representations that are directly suitable for computer implementation has received significantly less attention. Instead, a model is usually described in terms of a stochastic process or a "higher-level paradigm" with graphical representation such as e.g. a stochastic Petri net. A serious problem then arises due to the exponential growth of the model-s state space which is in fact a main reason for the popularity of stochastic simulation since simulation suffers less from the state space explosion than non-simulative numerical solution techniques. In this paper we present transition class models for the representation of biological network models, a compact mathematical formalism that circumvents state space explosion. Transition class models can also serve as an interface between different higher level modeling paradigms, stochastic processes and the implementation coded in a programming language. Besides, the compact model representation provides the opportunity to apply non-simulative solution techniques thereby preserving the possible use of stochastic simulation. Illustrative examples of transition class representations are given for an enzyme-catalyzed substrate conversion and a part of the bacteriophage λ lysis/lysogeny pathway.
Abstract: The recent advances in computational fluid dynamics
(CFD) can be useful in observing the detailed hemodynamics in
cerebral aneurysms for understanding not only their formation and
rupture but also for clinical evaluation and treatment. However,
important hemodynamic quantities are difficult to measure in vivo. In
the present study, an approximate model of normal middle cerebral
artery (MCA) along with two cases consisting broad and narrow
saccular aneurysms are analyzed. The models are generated in
ANSYS WORKBENCH and transient analysis is performed in
ANSYS-CFX. The results obtained are compared for three cases and
agree well with the available literature.
Abstract: Controlled modification of appropriate sharpness for
nanotips is of paramount importance to develop novel materials and
functional devices at a nanometer resolution. Herein, we present a
reliable and unique strategy of laser irradiation enhanced
physicochemical etching to manufacture super sharp tungsten tips
with reproducible shape and dimension as well as high yields
(~80%). The corresponding morphology structure evolution of
tungsten tips and laser-tip interaction mechanisms were
systematically investigated and discussed using field emission
scanning electron microscope (SEM) and physical optics statistics
method with different fluences under 532 nm laser irradiation. This
work paves the way for exploring more accessible metallic tips
applications with tunable apex diameter and aspect ratio, and,
furthermore, facilitates the potential sharpening enhancement
technique for other materials used in a variety of nanoscale devices.
Abstract: The aim of study was to evaluate pressure distribution characteristics of the elastic textile bandages using two instrumental techniques: a prototype Instrument and a load Transference. The prototype instrument which simulates shape of real leg has pressure sensors which measure bandage pressure. Using this instrument, the results show that elastic textile bandages presents different pressure distribution characteristics and none produces a uniform distribution around lower limb.
The load transference test procedure is used to determine whether a relationship exists between elastic textile bandage structure and pressure distribution characteristics. The test procedure assesses degree of load, directly transferred through a textile when loads series are applied to bandaging surface. A range of weave fabrics was produced using needle weaving machine and a sewing technique. A textile bandage was developed with optimal characteristics far superior pressure distribution than other bandages. From results, we find that theoretical pressure is not consistent exactly with practical pressure. It is important in this study to make a practical application for specialized nurses in order to verify the results and draw useful conclusions for predicting the use of this type of elastic band.
Abstract: This research paper presents a framework on how to
build up malware dataset.Many researchers took longer time to
clean the dataset from any noise or to transform the dataset into a
format that can be used straight away for testing. Therefore, this
research is proposing a framework to help researchers to speed up
the malware dataset cleaningprocesses which later can be used for
testing. It is believed, an efficient malware dataset cleaning
processes, can improved the quality of the data, thus help to improve
the accuracy and the efficiency of the subsequent analysis. Apart
from that, an in-depth understanding of the malware taxonomy is
also important prior and during the dataset cleaning processes. A
new Trojan classification has been proposed to complement this
framework.This experiment has been conducted in a controlled lab
environment and using the dataset from VxHeavens dataset. This
framework is built based on the integration of static and dynamic
analyses, incident response method and knowledge database
discovery (KDD) processes.This framework can be used as the basis
guideline for malware researchers in building malware dataset.
Abstract: A lot of Scientific and Engineering problems require the solution of large systems of linear equations of the form bAx in an effective manner. LU-Decomposition offers good choices for solving this problem. Our approach is to find the lower bound of processing elements needed for this purpose. Here is used the so called Omega calculus, as a computational method for solving problems via their corresponding Diophantine relation. From the corresponding algorithm is formed a system of linear diophantine equalities using the domain of computation which is given by the set of lattice points inside the polyhedron. Then is run the Mathematica program DiophantineGF.m. This program calculates the generating function from which is possible to find the number of solutions to the system of Diophantine equalities, which in fact gives the lower bound for the number of processors needed for the corresponding algorithm. There is given a mathematical explanation of the problem as well. Keywordsgenerating function, lattice points in polyhedron, lower bound of processor elements, system of Diophantine equationsand : calculus.
Abstract: Since the 1990s the American furniture industry faces
a transition period. Manufacturers, one of its most important actors
made its entrance into the retail industry. This shift has had deep
consequences not only for the American furniture industry as a
whole, but also for other international furniture industries, especially
the Chinese. The present work aims to analyze this actor based on the
distinction provided by the Global Commodity Chain Theory. It
stresses its characteristics, structure, operational way and importance
for both the U.S. and the Chinese furniture industries.
Abstract: This paper presents an experimental case using sensory thermography to describe temperatures behavior on median nerve once an activity of repetitive motion was done. Thermography is a noninvasive technique without biological hazard and not harm at all times and has been applied in many experiments to seek for temperature patterns that help to understand diseases like cancer and cumulative trauma disorders (CTD’s). An infrared sensory thermography technology was developed to execute this study. Three women in good shape were selected for the repetitive motion tests for 4 days, two right-handed women and 1 left handed woman, two sensory thermographers were put on both median nerve wrists to get measures. The evaluation time was of 3 hours 30 minutes in a controlled temperature, 20 minutes of stabilization time at the beginning and end of the operation. Temperatures distributions are statistically evaluated and showed similar temperature patterns behavior.