Abstract: In this paper, a worm-like micro robot designed for inpipe
application with intelligent active force control (AFC) capability
is modelled and simulated. The motion of the micro robot is based on
an impact drive mechanism (IDM) that is actuated using piezoelectric
device. The trajectory tracking performance of the modelled micro
robot is initially experimented via a conventional proportionalintegral-
derivative (PID) controller in which the dynamic response of
the robot system subjected to different input excitations is
investigated. Subsequently, a robust intelligent method known as
active force control with fuzzy logic (AFCFL) is later incorporated
into the PID scheme to enhance the system performance by
compensating the unwanted disturbances due to the interaction of the
robot with its environment. Results show that the proposed AFCFL
scheme is far superior than the PID control counterpart in terms of
the system-s tracking capability in the wake of the disturbances.
Abstract: We propose a new approach on how to obtain the approximate solutions of Hamilton-Jacobi (HJ) equations. The process of the approximation consists of two steps. The first step is to transform the HJ equations into the virtual time based HJ equations (VT-HJ) by introducing a new idea of ‘virtual-time’. The second step is to construct the approximate solutions of the HJ equations through a computationally iterative procedure based on the VT-HJ equations. It should be noted that the approximate feedback solutions evolve by themselves as the virtual-time goes by. Finally, we demonstrate the effectiveness of our approximation approach by means of simulations with linear and nonlinear control problems.
Abstract: Harmonic pollution and low power factor in power
systems caused by power converters have been of great concern. To
overcome these problems several converter topologies using
advanced semiconductor devices and control schemes have been
proposed. This investigation is to identify a low cost, small size,
efficient and reliable ac to dc converter to meet the input performance
index of UPS. The performance of single phase and three phase ac to
dc converter along with various control techniques are studied and
compared. The half bridge converter topology with linear current
control is identified as most suitable. It is simple, energy efficient
because of single switch power loss and transformer-less operation of
UPS. The results are validated practically using a prototype built
using IGBT and analog controller. The performance for both single
and three-phase system is verified. Digital implementation of closed
loop control achieves higher reliability. Its cost largely depends on
chosen bit precision. The minimal bit precision for optimum
converter performance is identified as 16-bit with fixed-point
operation. From the investigation and practical implementation it is
concluded that half bridge ac – dc converter along with digital linear
controller meets the performance index of UPS for single and three
phase systems.
Abstract: Lately management strategy that put Industrial Design (ID) in its core is recognized more important, as technology and price alone cannot differentiate a product. The needs to shorten the time to develop a product also shorten the development period of ID, and it necessitates the ID process management. This research analyzes the status of integration process of ID and Engineering Design (ED) of office equipment that requires the collaboration of ID and ED to clarify the issues for the efficiency of the development and to propose solutions.
Abstract: Fault-proneness of a software module is the
probability that the module contains faults. A correlation exists
between the fault-proneness of the software and the measurable
attributes of the code (i.e. the static metrics) and of the testing (i.e.
the dynamic metrics). Early detection of fault-prone software
components enables verification experts to concentrate their time and
resources on the problem areas of the software system under
development. This paper introduces Genetic Algorithm based
software fault prediction models with Object-Oriented metrics. The
contribution of this paper is that it has used Metric values of JEdit
open source software for generation of the rules for the classification
of software modules in the categories of Faulty and non faulty
modules and thereafter empirically validation is performed. The
results shows that Genetic algorithm approach can be used for
finding the fault proneness in object oriented software components.
Abstract: So much energy is used in high rise buildings to fulfill
the basic needs of users such as lighting and thermal comfort.
Malaysia has hot and humid climate, buildings especially high rise
buildings receive unnecessary solar radiation that cause more solar
heat gain. Energy use specially electricity consumption in high rise
buildings has increased. There have been growing concerns about
energy consumption and its effect on environment. Building, energy
and the environment are important issues that the designers should
consider to them. Self protected form is one of possible ways against
the impact of solar radiation in high rise buildings. The Energy
performance of building envelopes was investigated in term of the
Overall Thermal Transfer Value (OTTV ).In this paper, the amount
of OTTV reduction was calculated through OTTV Equations to
clear the effectiveness of self shading strategy on minimizing energy
consumption for cooling interior spaces in high rise buildings which
has considerable envelope areas against solar radiation. Also increasing
the optimum window area was investigated using self-shading
strategy in designing high rise buildings. As result, the significant
reduction in OTTV was shown based on WWR.In addition slight
increase was demonstrated in WWR that can influence on visible
comfort interior spaces.
Abstract: Numerical parametric study is conducted to study the effects of ampoule rotation on the flows and the dopant segregation in vertical bridgman (vb) crystal growth. Calculations were performed in unsteady state. The extended darcy model, which includes the time derivative and coriolis terms, has been employed in the momentum equation. It’s found that the convection, and dopant segregation can be affected significantly by ampoule rotation, and the effect is similar to that by an axial magnetic field. Ampoule rotation decreases the intensity of convection and stretches the flow cell axially. When the convection is weak, the flow can be suppressed almost completely by moderate ampoule rotation and the dopant segregation becomes diffusion-controlled. For stronger convection, the elongated flow cell by ampoule rotation may bring dopant mixing into the bulk melt reducing axial segregation at the early stage of the growth. However, if the cellular flow cannot be suppressed completely, ampoule rotation may induce larger radial segregation due to poor mixing.
Abstract: One of the most important parameters to develop and
manage urban areas is appropriate selection of land surface to
develop green spaces in these areas. In this study, in order to identify
the most appropriate sites and areas cultivated for ornamental species
in Jiroft, Landsat Enhanced Thematic Mapper Plus (ETM+) images
due to extract the most important effective climatic and adaphic
parameters for growth ornamental species were used. After geometric
and atmospheric corrections applied, to enhance accuracy of multi
spectral (XS) bands, the fusion of Landsat XS bands by IRS-1D
panchromatic band (PAN) was performed. After field sampling to
evaluate the correlation between different factors in surface soil
sampling location and different bands digital number (DN) of ETM+
sensor on the same points, correlation tables formed using the best
computational model and the map of physical and chemical
parameters of soil was produced. Then the accuracy of them was
investigated by using kappa coefficient. Finally, according to
produced maps, the best areas for cultivation of recommended
species were introduced.
Abstract: This paper investigates the problem of tracking spa¬tiotemporal changes of a satellite image through the use of Knowledge Discovery in Database (KDD). The purpose of this study is to help a given user effectively discover interesting knowledge and then build prediction and decision models. Unfortunately, the KDD process for spatiotemporal data is always marked by several types of imperfections. In our paper, we take these imperfections into consideration in order to provide more accurate decisions. To achieve this objective, different KDD methods are used to discover knowledge in satellite image databases. Each method presents a different point of view of spatiotemporal evolution of a query model (which represents an extracted object from a satellite image). In order to combine these methods, we use the evidence fusion theory which considerably improves the spatiotemporal knowledge discovery process and increases our belief in the spatiotemporal model change. Experimental results of satellite images representing the region of Auckland in New Zealand depict the improvement in the overall change detection as compared to using classical methods.
Abstract: In this study, ZnO nano rods and ZnO ultrafine particles were synthesized by Gel-casting method. The synthesized ZnO powder has a hexagonal zincite structure. The ZnO aggregates with rod-like morphology are typically 1.4 μm in length and 120 nm in diameter, which consist of many small nanocrystals with diameters of 10 nm. Longer wires connected by many hexahedral ZnO nanocrystals were obtained after calcinations at the temperature over 600° C.The crystalline structures and morphologies of the powder have been characterized by X-ray diffraction(XRD) and Scaning electron microscopy (SEM).The result shows that the different preparation conditions such as concentration H2O, calcinations time and calcinations temperature have a lot of influences upon the properties of nano ZnO powders, an increase in the temperature of the calcinations results in an increase of the grain size and also the increase of the calcinations time in high temperature makes the size of the grains bigger. The existences of extra watter prevent nano grains from improving like rod morphology. We have obtained the smallest grain size of ZnO powder by controlling the process conditions. Finally In a suitable condition, a novel nanostructure, namely bi-rod-like ZnO nano rods was found which is different from known ZnO nanostructures.
Abstract: Alkali Activated Slag Concrete (AASC) mixes are manufactured by activating ground granulated blast furnace slag (GGBFS) using sodium hydroxide and sodium silicate solutions. The aim of the present experimental research was to investigate the effect of increasing the dosages of sodium oxide (Na2O, in the range of 4 to 8%) and the activator modulus (Ms) (i.e. the SiO2/Na2O ratio, in the range of 0.5 to 1.5) of the alkaline solutions, on the workability and strength characteristics of self-cured (air-cured) alkali activated Indian slag concrete mixes. Further the split tensile and flexure strengths for optimal mixes were studied for each dosage of Na2O.It is observed that increase in Na2O concentration increases the compressive, split-tensile and flexural strengths, both at the early and later-ages, while increase in Ms, decreases the workability of the mixes. An optimal Ms of 1.25 is found at various Na2O dosages. No significant differences in the strength performances were observed between AASCs manufactured with alkali solutions prepared using either of potable and de-ionized water.
Abstract: Industrial robots play a vital role in automation
however only little effort are taken for the application of robots in
machining work such as Grinding, Cutting, Milling, Drilling,
Polishing etc. Robot parallel manipulators have high stiffness,
rigidity and accuracy, which cannot be provided by conventional
serial robot manipulators. The aim of this paper is to perform the
modeling and the workspace analysis of a 3 DOF Parallel
Manipulator (3 DOF PM). The 3 DOF PM was modeled and
simulated using 'ADAMS'. The concept involved is based on the
transformation of motion from a screw joint to a spherical joint
through a connecting link. This paper work has been planned to
model the Parallel Manipulator (PM) using screw joints for very
accurate positioning. A workspace analysis has been done for the
determination of work volume of the 3 DOF PM. The position of the
spherical joints connected to the moving platform and the
circumferential points of the moving platform were considered for
finding the workspace. After the simulation, the position of the joints
of the moving platform was noted with respect to simulation time and
these points were given as input to the 'MATLAB' for getting the
work envelope. Then 'AUTOCAD' is used for determining the work
volume. The obtained values were compared with analytical
approach by using Pappus-Guldinus Theorem. The analysis had been
dealt by considering the parameters, link length and radius of the
moving platform. From the results it is found that the radius of
moving platform is directly proportional to the work volume for a
constant link length and the link length is also directly proportional
to the work volume, at a constant radius of the moving platform.
Abstract: The development of wearable sensing technologies is a great challenge which is being addressed by the Proetex FP6 project (www.proetex.org). Its main aim is the development of wearable sensors to improve the safety and efficiency of emergency personnel. This will be achieved by continuous, real-time monitoring of vital signs, posture, activity, and external hazards surrounding emergency workers. We report here the development of carbon dioxide (CO2) sensing boot by incorporating commercially available CO2 sensor with a wireless platform into the boot assembly. Carefully selected commercially available sensors have been tested. Some of the key characteristics of the selected sensors are high selectivity and sensitivity, robustness and the power demand. This paper discusses some of the results of CO2 sensor tests and sensor integration with wireless data transmission
Abstract: This paper proposes a low-voltage and low-power
fully integrated digitally tuned continuous-time channel selection
filter for WiMAX applications. A 5th-order elliptic low-pass filter is
realized in a Gm-C topology. The bandwidth of the fully differential
filter is reconfigurable from 2.5MHz to 20MHz (8x) for different
requirements in WiMAX applications. The filter is simulated in a
standard 90nm CMOS process. Simulation results show the THD
(@Vout =100mVpp) is less than -66dB. The in-band ripple of the
filter is about 0.15dB. The filter consumes 1.5mW from a supply
voltage of 0.9V.
Abstract: In the context of large volume Big Divisor (nearly)
SLagy D3/D7 μ-Split SUSY [1], after an explicit identification
of first generation of SM leptons and quarks with fermionic superpartners
of four Wilson line moduli, we discuss the identification of
gravitino as a potential dark matter candidate by explicitly calculating
the decay life times of gravitino (LSP) to be greater than age of
universe and lifetimes of decays of the co-NLSPs (the first generation
squark/slepton and a neutralino) to the LSP (the gravitino) to be
very small to respect BBN constraints. Interested in non-thermal
production mechanism of gravitino, we evaluate the relic abundance
of gravitino LSP in terms of that of the co-NLSP-s by evaluating
their (co-)annihilation cross sections and hence show that the former
satisfies the requirement for a potential Dark Matter candidate. We
also show that it is possible to obtain a 125 GeV light Higgs in our
setup.
Abstract: A registration framework for image-guided robotic
surgery is proposed for three emergency neurosurgical procedures,
namely Intracranial Pressure (ICP) Monitoring, External Ventricular
Drainage (EVD) and evacuation of a Chronic Subdural Haematoma
(CSDH). The registration paradigm uses CT and white light as
modalities. This paper presents two simulation studies for a
preliminary evaluation of the registration protocol: (1) The loci of the
Target Registration Error (TRE) in the patient-s axial, coronal and
sagittal views were simulated based on a Fiducial Localisation Error
(FLE) of 5 mm and (2) Simulation of the actual framework using
projected views from a surface rendered CT model to represent white
light images of the patient. Craniofacial features were employed as
the registration basis to map the CT space onto the simulated
intraoperative space. Photogrammetry experiments on an artificial
skull were also performed to benchmark the results obtained from the
second simulation. The results of both simulations show that the
proposed protocol can provide a 5mm accuracy for these
neurosurgical procedures.
Abstract: Artificial Immune System (AIS) is relatively naive paradigm for intelligent computations. The inspiration for AIS is derived from natural Immune System (IS). Classically it is believed that IS strives to discriminate between self and non-self. Most of the existing AIS research is based on this approach. Danger Theory (DT) argues this approach and proposes that IS fights against danger producing elements and tolerates others. We, the computational researchers, are not concerned with the arguments among immunologists but try to extract from it novel abstractions for intelligent computation. This paper aims to follow DT inspiration for intelligent data processing. The approach may introduce new avenue in intelligent processing. The data used is system calls data that is potentially significant in intrusion detection applications.
Abstract: DC-DC converters are widely used in regulated switched mode power supplies and in DC motor drive applications. There are several sources of unwanted nonlinearity in practical power converters. In addition, their operation is characterized by switching that gives birth to a variety of nonlinear dynamics. DC-DC buck and boost converters controlled by pulse-width modulation (PWM) have been simulated. The voltage waveforms and attractors obtained from the circuit simulation have been studied. With the onset of instability, the phenomenon of subharmonic oscillations, quasi-periodicity, bifurcations, and chaos have been observed. This paper is mainly motivated by potential contributions of chaos theory in the design, analysis and control of power converters, in particular and power electronics circuits, in general.
Abstract: In this paper, a new model order reduction
phenomenon is introduced at the design stage of linear phase digital
IIR filter. The complexity of a system can be reduced by adopting the
model order reduction method in their design. In this paper a mixed
method of model order reduction is proposed for linear IIR filter. The
proposed method employs the advantages of factor division technique
to derive the reduced order denominator polynomial and the reduced
order numerator is obtained based on the resultant denominator
polynomial. The order reduction technique is used to reduce the delay
units at the design stage of IIR filter. The validity of the proposed
method is illustrated with design example in frequency domain and
stability is also examined with help of nyquist plot.
Abstract: Ranking of fuzzy numbers play an important role in
decision making, optimization, forecasting etc. Fuzzy numbers must
be ranked before an action is taken by a decision maker. In this
paper, with the help of several counter examples it is proved that
ranking method proposed by Chen and Chen (Expert Systems with
Applications 36 (2009) 6833-6842) is incorrect. The main aim of this
paper is to propose a new approach for the ranking of generalized
trapezoidal fuzzy numbers. The main advantage of the proposed
approach is that the proposed approach provide the correct ordering
of generalized and normal trapezoidal fuzzy numbers and also the
proposed approach is very simple and easy to apply in the real life
problems. It is shown that proposed ranking function satisfies all
the reasonable properties of fuzzy quantities proposed by Wang and
Kerre (Fuzzy Sets and Systems 118 (2001) 375-385).