Abstract: The aim of the research work is to modify the NACA 4215 airfoil with flap and rotary cylinder at the leading edge of the airfoil and experimentally study the static pressure distribution over the airfoil completed with flap and leading-edge vortex generator. In this research, NACA 4215 wing model has been constructed by generating the profile geometry using the standard equations and design software such as AutoCAD and SolidWorks. To perform the experiment, three wooden models are prepared and tested in subsonic wind tunnel. The experiments were carried out in various angles of attack. Flap angle and momentum injection rate are changed to observe the characteristics of pressure distribution. In this research, a new concept of flow separation control mechanism has been introduced to improve the aerodynamic characteristics of airfoil. Control of flow separation over airfoil which experiences a vortex generator (rotating cylinder) at the leading edge of airfoil is experimentally simulated under the effects of momentum injection. The experimental results show that the flow separation control is possible by the proposed mechanism, and benefits can be achieved by momentum injection technique. The wing performance is significantly improved due to control of flow separation by momentum injection method.
Abstract: A survey of small-size contractors in Jeju was conducted to investigate college graduate's computer-aided design (CAD) competence. Most of small-size contractors use CAD software to review and update drawings submitted from an architect. This research analyzed the curriculum of the architectural engineering in several national universities. The CAD classes have 4 or 6 hours per week and use AutoCAD primarily. This paper proposes that a CAD class needs 6 hours per week, 2D drawing is the main theme in the curriculum, and exercises to make 3D models are also included in the CAD class. An improved method, for example Internet cafe and real time feedbacks using smartphones, to evaluate the reports and exercise results is necessary.
Abstract: This paper presents an analytical study of Small Unmanned Aerial Vehicle (SUAV) dynamic stability derivatives. Simulating SUAV dynamics and analyzing its behavior at the earliest design stages is too important and more efficient design aspect. The approach suggested in this paper is using the wind tunnel experiment to collect the aerodynamic data and get the dynamic stability derivatives. AutoCAD Software was used to draw the case study (wildlife surveillance SUAV). The SUAV is scaled down to be 0.25% of the real SUAV dimensions and converted to a wind tunnel model. The model was tested in three different speeds for three different attitudes which are; pitch, roll and yaw. The wind tunnel results were then used to determine the case study stability derivative values, and hence it used to calculate the roots of the characteristic equation for both longitudinal and lateral motions. Finally, the characteristic equation roots were found and discussed in all possible cases.
Abstract: This study is aimed towards the automisation of basic patternmaking for traditional clothes for the purpose of mass production using AutoCAD to apply AutoLISP feature under software Hazi Attire. A standard dress form (industrial form) with the size of small (S), medium (M) and large (L) size is measured using full body scanning machine. Later, the pattern for the clothes is designed parametrically based on the measured dress form. Hazi Attire program is used within the framework of AutoCAD to generate the basic pattern of front bodice, back bodice, front skirt, back skirt and sleeve block (sloper). The generation of pattern is based on the parameters inputted by user, whereby in this study, the parameters were determined based on the measured size of dress form. The finalized pattern parameter shows that the pattern fit perfectly on the dress form. Since the pattern is generated almost instantly, these proved that using the AutoLISP programming, the manufacturing lead time for the mass production of the traditional clothes can be decreased.
Abstract: This paper explains how the New Jersey Institute of Technology surveying student team members designed and created an interactive GIS map, the purpose of which is to be useful to the land surveyor and engineer for project management. This was achieved by building a research and storage database that can be easily integrated into any land surveyor’s current operations through the use of ArcGIS 10, Arc Catalog, and AutoCAD. This GIS database allows for visual representation and information querying for multiple job sites, and simple access to uploaded data, which is geospatially referenced to each individual job site or project. It can also be utilized by engineers to determine design criteria, or to store important files. This cost-effective approach to a surveying map not only saves time, but saves physical storage space and paper resources.
Abstract: Industrial robots play a vital role in automation
however only little effort are taken for the application of robots in
machining work such as Grinding, Cutting, Milling, Drilling,
Polishing etc. Robot parallel manipulators have high stiffness,
rigidity and accuracy, which cannot be provided by conventional
serial robot manipulators. The aim of this paper is to perform the
modeling and the workspace analysis of a 3 DOF Parallel
Manipulator (3 DOF PM). The 3 DOF PM was modeled and
simulated using 'ADAMS'. The concept involved is based on the
transformation of motion from a screw joint to a spherical joint
through a connecting link. This paper work has been planned to
model the Parallel Manipulator (PM) using screw joints for very
accurate positioning. A workspace analysis has been done for the
determination of work volume of the 3 DOF PM. The position of the
spherical joints connected to the moving platform and the
circumferential points of the moving platform were considered for
finding the workspace. After the simulation, the position of the joints
of the moving platform was noted with respect to simulation time and
these points were given as input to the 'MATLAB' for getting the
work envelope. Then 'AUTOCAD' is used for determining the work
volume. The obtained values were compared with analytical
approach by using Pappus-Guldinus Theorem. The analysis had been
dealt by considering the parameters, link length and radius of the
moving platform. From the results it is found that the radius of
moving platform is directly proportional to the work volume for a
constant link length and the link length is also directly proportional
to the work volume, at a constant radius of the moving platform.
Abstract: This paper is intended to assist anyone with some general technical experience, but perhaps limited specific knowledge of heat transfer equipment. A characteristic of heat exchanger design is the procedure of specifying a design, heat transfer area and pressure drops and checking whether the assumed design satisfies all requirements or not. The purpose of this paper is how to design the oil cooler (heat exchanger) especially for shell-and-tube heat exchanger which is the majority type of liquid-to-liquid heat exchanger. General design considerations and design procedure are also illustrated in this paper and a flow diagram is provided as an aid of design procedure. In design calculation, the MatLAB and AutoCAD software are used. Fundamental heat transfer concepts and complex relationships involved in such exchanger are also presented in this paper. The primary aim of this design is to obtain a high heat transfer rate without exceeding the allowable pressure drop. This computer program is highly useful to design the shell-and-tube type heat exchanger and to modify existing deign.
Abstract: In today-s era of plasma and laser cutting, machines using oxy-acetylene flame are also meritorious due to their simplicity and cost effectiveness. The objective to devise a Computer controlled Oxy-Fuel profile cutting machine arose from the increasing demand for metal cutting with respect to edge quality, circularity and lesser formation of redeposit material. The System has an 8 bit micro controller based embedded system, which assures stipulated time response. A new window based Application software was devised which takes a standard CAD file .DXF as input and converts it into numerical data required for the controller. It uses VB6 as a front end whereas MS-ACCESS and AutoCAD as back end. The system is designed around AT89C51RD2, powerful 8 bit, ISP micro controller from Atmel and is optimized to achieve cost effectiveness and also maintains the required accuracy and reliability for complex shapes. The backbone of the system is a cleverly designed mechanical assembly along with the embedded system resulting in an accuracy of about 10 microns while maintaining perfect linearity in the cut. This results in substantial increase in productivity. The observed results also indicate reduced inter laminar spacing of pearlite with an increase in the hardness of the edge region.
Abstract: This study created new graphical icons and operating
functions in a CAD/CAM software system by analyzing icons in some
of the popular systems, such as AutoCAD, AlphaCAM, Mastercam
and the 1st edition of LiteCAM. These software systems all focused on
geometric design and editing, thus how to transmit messages
intuitively from icon itself to users is an important function of
graphical icons. The primary purpose of this study is to design
innovative icons and commands for new software.
This study employed the TRIZ method, an innovative design
method, to generate new concepts systematically. Through literature
review, it then investigated and analyzed the relationship between
TRIZ and idea development. Contradiction Matrix and 40 Principles
were used to develop an assisting tool suitable for icon design in
software development. We first gathered icon samples from the
selected CAD/CAM systems. Then grouped these icons by
meaningful functions, and compared useful and harmful properties.
Finally, we developed new icons for new software systems in order to
avoid intellectual property problem.
Abstract: In this paper a low cost knowledge base system (KBS)
framework is proposed for design of deep drawing die and procedure
for developing system modules. The task of building the system is
structured into different modules for major activities of design of
deep drawing die. A manufacturability assessment module of the
proposed framework is developed to check the manufacturability of
deep drawn parts. The technological knowledge is represented by
using IF- THEN rules and it is coded in AutoLISP language. The
module is designed to be loaded into the prompt area of AutoCAD.
The cost of implementation of proposed system makes it affordable
for small and medium scale sheet metal industries.
Abstract: This paper discusses the landscape design that could
increase energy efficiency in a house. By planting trees in a house
compound, the tree shades prevent direct sunlight from heating up
the building, and it enables cooling off the surrounding air. The
requirement for air-conditioning could be minimized and the air
quality could be improved. During the life time of a tree, the saving
cost from the mentioned benefits could be up to US $ 200 for each
tree. The project intends to visually describe the landscape design in
a house compound that could enhance energy efficiency and
consequently lead to energy saving. The house compound model was
developed in three dimensions by using AutoCAD 2005, the
animation was programmed by using LightWave 3D softwares i.e.
Modeler and Layout to display the tree shadings in the wall. The
visualization was executed on a VRML Pad platform and
implemented on a web environment.