Abstract: Heat pipes are used to control the thermal problem for
electronic cooling. It is especially difficult to dissipate heat to a heat
sink in an environment in space compared to earth. For solving this
problem, in this study, the Poiseuille (Po) number, which is the main
measure of the performance of a heat pipe, is studied by CFD; then, the
heat pipe performance is verified with experimental results. A heat
pipe is then fabricated for a spatial environment, and an in-house code
is developed. Further, a heat pipe subsystem, which consists of a heat
pipe, MLI (Multi Layer Insulator), SSM (Second Surface Mirror), and
radiator, is tested and correlated with the TMM (Thermal
Mathematical Model) through a commercial code. The correlation
results satisfy the 3K requirement, and the generated thermal model is
verified for application to a spatial environment.
Abstract: In this paper, we propose a novel frequency offset
estimation scheme for orthogonal frequency division multiplexing
(OFDM) systems. By correlating the OFDM signals within the coherence
phase bandwidth and employing a threshold in the frequency
offset estimation process, the proposed scheme is not only robust to
the timing offset but also has a reduced complexity compared with
that of the conventional scheme. Moreover, a timing offset estimation
scheme is also proposed as the next stage of the proposed frequency
offset estimation. Numerical results show that the proposed scheme
can estimate frequency offset with lower computational complexity
and does not require additional memory while maintaining the same
level of estimation performance.
Abstract: This paper develops a quality estimation method with
the application of fuzzy hierarchical clustering. Quality estimation is
essential to quality control and quality improvement as a precise
estimation can promote a right decision-making in order to help
better quality control. Normally the quality of finished products in
manufacturing system can be differentiated by quality standards. In
the real life situation, the collected data may be vague which is not
easy to be classified and they are usually represented in term of fuzzy
number. To estimate the quality of product presented by fuzzy
number is not easy. In this research, the trapezoidal fuzzy numbers
are collected in manufacturing process and classify the collected data
into different clusters so as to get the estimation. Since normal
hierarchical clustering methods can only be applied for real numbers,
fuzzy hierarchical clustering is selected to handle this problem based
on quality standards.
Abstract: In this paper, we consider Wiener nonlinear model for solid oxide fuel cell (SOFC). The Wiener model of the SOFC consists of a linear dynamic block and a static output non-linearity followed by the block, in which linear part is approximated by state-space model and the nonlinear part is identified by a polynomial form. To control the SOFC system, we have to consider various view points such as operating conditions, another constraint conditions, change of load current and so on. A change of load current is the significant one of these for good performance of the SOFC system. In order to keep the constant stack terminal voltage by changing load current, the nonlinear model predictive control (MPC) is proposed in this paper. After primary control method is designed to guarantee the fuel utilization as a proper constant, a nonlinear model predictive control based on the Wiener model is developed to control the stack terminal voltage of the SOFC system. Simulation results verify the possibility of the proposed Wiener model and MPC method to control of SOFC system.
Abstract: Employee-s task performance has been recognized as a
core contributor to overall organizational effectiveness. Hence,
verifying the determinants of task performance is one of the most
important research issues. This study tests the influence of perceived
organizational support, abusive supervision, and exchange ideology
on employee-s task performance. We examined our hypotheses by
collecting self-reported data from 413 Korean employees in different
organizations. Our all hypotheses gained support from the results.
Implications for research and directions for future research are
discussed.
Abstract: In this paper, the performance of three types of serial
concatenated convolutional codes (SCCC) is compared and analyzed
in additive white Gaussian noise (AWGN) channel. In Type I, only the
parity bits of outer encoder are passed to inner encoder. In Type II and
Type III, both the information bits and the parity bits of outer encoder
are transferred to inner encoder. As results of simulation, Type I shows
the best bit error rate (BER) performance at low signal-to-noise ratio
(SNR). On the other hand, Type III shows the best BER performance
at high SNR in AWGN channel. The simulation results are analyzed
using the distance spectrum.
Abstract: This analysis investigates the distortion of flow
measurement and the increase of cavitation along orifice
flowmeter. The analysis using the numerical method (CFD)
validated the distortion of flow measurement through the inlet
velocity profile considering the convergence and grid
dependency. Realizable k-e model was selected and y+ was
about 50 in this numerical analysis. This analysis also estimated
the vulnerability of cavitation effect due to inlet velocity profile.
The investigation concludes that inclined inlet velocity profile
could vary the pressure which was measured at pressure tab
near pipe wall and it led to distort the pressure values ranged
from -3.8% to 5.3% near the orifice plate and to make the
increase of cavitation. The investigation recommends that the
fully developed inlet velocity flow is beneficial to accurate flow
measurement in orifice flowmeter.
Abstract: Building conservation work generally involves complex and non-standard work different from new building construction processes. In preparing tenders for building conservation projects, therefore, the quantity surveyor must carefully consider the specificity of non-standard items and demarcate the scope of unique conservation work. While the quantity surveyor must appreciate the full range of works to prepare a good tender document, he typically manages many unfamiliar elements, including practical construction methods, restoration techniques and work sequences. Only by fulfilling the demanding requirements of building conservation work can the quantity surveyor enhance his professionalism an area of growing cultural value and economic importance. By discussing several issues crucial to tender preparations for building conservation projects in Malaysia, this paper seeks a deeper understanding of how quantity surveying can better standardize tender preparation work and more successfully manage building conservation processes.
Abstract: The enthusiasm for gluten avoidance in a growing
market is met by improvements in sensitive detection methods for
analysing gluten content. Paradoxically, manufacturers employ no
such systems in the production process but continue to market their
product as gluten free, a significant risk posed to an undetermined
coeliac population. This paper resonates with an immunological
response that causes gastrointestinal scarring and villous atrophy with
the conventional description of personal injury. This thesis divulges
into evaluating potential inadequacies of gluten labelling laws which
not only present a diagnostic challenge for general practitioners in the
UK but it also exposes a less than adequate form of available legal
protection to those who suffer adverse reactions as a result of gluten
digestion. Central to this discussion is whether a claim brought in
misrepresentation, negligence and/or under the Consumer Protection
Act 1987 could be sustained. An interesting comparison is then made
with the legal regimes of neighboring jurisdictions furthering the
theme of a legally un-catered for gluten kingdom.
Abstract: The main objective of our study is to collect data
about the profile of the asthmatic patients in Assam and thereby have
a comprehensive knowledge of the factors influencing the asthmatic
patients of the state and their medication pattern. We developed a
search strategy to find any publication about the community based
survey asthma related and used. These to search the MEDLINE
(1996 to current literature) CINAHL DOAJ pubmed databases using
the key phrases, Asthma, Respiratory disorders, Drug therapy of
Asthma, database decision support system and asthma. The
appropriate literature was printed out from the online source and
library (Journal) source. The study was conducted through a set of
structured and non-structured questionnaires targeted on the
asthmatic patients belonging to the rural and urban areas of Assam,
during the month of Dec 2006 to July 2007, 138 cases were studied
in Gauwathi Medical College & Hospital located in Bhangagarh,
Assam in India. The demographic characteristics a factor in 138
patients with asthma with allergic rhinitis (cases) gives the detail
profile of asthmatic patient-s distribution of Assam as classified on
the basis of age and sex. It is evident from the study that male
populations (66%) are more prone to asthma as compared to the
females (34%).Another striking features that emerged from this
survey is the maximum prevalence of asthma in the age group of 20-
30 years followed by infants belonging to the age group of 7 (0.05%)
0-10years among both male and female populations of Assam. The
high incidence of asthma in the age group of 20-30 years may
probably be due to the allergy arising out of sudden exposure to dust
and pollen which the children face while playing and going to the
school. The rural females in the age group of 30-40 years are more
prone to asthma than urban females in the same age group may be
due to sex differentiation among the tribal population of the state.
Pharmacists should educate the asthmatics how to use inhalers
considering growing menace of asthma in the state. Safer drugs
should be produced in the form of aerosol so that easy administration
by the asthmatic patients and physicians of the state is possible for
curing asthma. The health centers should be more equipped with the
medicines to cure asthma in the state like Assam.
Abstract: Bleeding in the digestive duct is an important diagnostic parameter for patients. Blood in the endoscopic image can be determined by investigating the color tone of blood due to the degree of oxygenation, under- or over- illumination, food debris and secretions, etc. However, we found that how to pre-process raw images obtained from the capsule detectors was very important. We applied various image process methods suitable for the capsule endoscopic image in order to remove noises and unbalanced sensitivities for the image pixels. The results showed that much improvement was achieved by additional pre-processing techniques on the algorithm of determining bleeding areas.
Abstract: In many sensor network applications, sensor nodes are deployed in open environments, and hence are vulnerable to physical attacks, potentially compromising the node's cryptographic keys. False sensing report can be injected through compromised nodes, which can lead to not only false alarms but also the depletion of limited energy resource in battery powered networks. Ye et al. proposed a statistical en-route filtering scheme (SEF) to detect such false reports during the forwarding process. In this scheme, the choice of a security threshold value is important since it trades off detection power and overhead. In this paper, we propose a fuzzy logic for determining a security threshold value in the SEF based sensor networks. The fuzzy logic determines a security threshold by considering the number of partitions in a global key pool, the number of compromised partitions, and the energy level of nodes. The fuzzy based threshold value can conserve energy, while it provides sufficient detection power.
Abstract: Since 2005, an SRF module of CESR type serves as the
accelerating cavity at the Taiwan Light Source in the National
Synchrotron Radiation Research Center. A 500-MHz niobium cavity
is immersed in liquid helium inside this SRF module. To reduce heat
load, the liquid helium vessel is thermally shielded by
liquid-nitrogen-cooled copper layer, and the beam chambers are also
anchored with pipes of the liquid nitrogen flow in middle of the liquid
helium vessel and the vacuum vessel. A strong correlation of the
movement of the cavity-s frequency tuner with the temperature
variation of parts cooled with liquid nitrogen was observed. A
previous study on a spare SRF module with the niobium cavity cooled
by liquid nitrogen instead of liquid helium, satisfactory suppression of
the thermal oscillation was achieved by attaching a temporary buffer
tank for the vented shielding nitrogen flow from the SRF module. In
this study, a home-made buffer tank is designed and integrated to the
spare SRF module with cavity cooled by liquid helium. Design,
construction, integration, and preliminary test results of this buffer
tank are presented.
Abstract: Elateriospermum tapos seed (buah perah) is the one
of the rich sources of polyunsaturated fatty acids. It contains high
percentage of oleic acid which is the important component to develop
nervous system and also α-linolenic acid (ALA) which is the
precursor of omega-3 fatty acids series to synthesize
eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA).
However, there is less study about this valuable oilseed and exploit
its potential. Therefore, this paper is to assess the comparison of
physico-chemical properties and fatty composition of perah oil to
palm oil and soybean oil. From the comparison, perah oil shows low
peroxide value means it has good oxidative stability and also high
iodine values shows that it can be used in paint industry. The study
shown that perah oil is comparable to palm oil and soybean oil, so it
has high potential to be exploited in the oleochemical,
pharmaceutical, cosmetics and paint industries.
Abstract: We propose a new fiber lens structure for large distance
measurement in which a polymer layer is added to a conventional
fiber lens. The proposed fiber lens can adjust the working distance by
properly choosing the refractive index and thickness of the polymer
layer. In our numerical analysis for the fiber lens radius of 120 μm,
the working distance of the proposed fiber lens is about 10 mm
which is about 30 times larger than conventional fiber lens.
Abstract: An ontology is widely used in many kinds of applications as a knowledge representation tool for domain knowledge. However, even though an ontology schema is well prepared by domain experts, it is tedious and cost-intensive to add instances into the ontology. The most confident and trust-worthy way to add instances into the ontology is to gather instances from tables in the related Web pages. In automatic populating of instances, the primary task is to find the most proper concept among all possible concepts within the ontology for a given table. This paper proposes a novel method for this problem by defining the similarity between the table and the concept using the overlap of their properties. According to a series of experiments, the proposed method achieves 76.98% of accuracy. This implies that the proposed method is a plausible way for automatic ontology population from Web tables.
Abstract: This paper introduces an automatic voice classification
system for the diagnosis of individual constitution based on Sasang
Constitutional Medicine (SCM) in Traditional Korean Medicine
(TKM). For the developing of this algorithm, we used the voices of
309 female speakers and extracted a total of 134 speech features from
the voice data consisting of 5 sustained vowels and one sentence. The
classification system, based on a rule-based algorithm that is derived
from a non parametric statistical method, presents 3 types of decisions:
reserved, positive and negative decisions. In conclusion, 71.5% of the
voice data were diagnosed by this system, of which 47.7% were
correct positive decisions and 69.7% were correct negative decisions.
Abstract: The rapid advance of communication technology is
evolving the network environment into the broadband convergence
network. Likewise, the IT services operated in the individual network
are also being quickly converged in the broadband convergence
network environment. VoIP and IPTV are two examples of such new
services. Efforts are being made to develop the video phone service,
which is an advanced form of the voice-oriented VoIP service.
However, the new IT services will be subject to stability and reliability
vulnerabilities if the relevant security issues are not answered during
the convergence of the existing IT services currently being operated in
individual networks within the wider broadband network
environment. To resolve such problems, this paper attempts to analyze
the possible threats and identify the necessary security measures
before the deployment of the new IT services. Furthermore, it
measures the quality of the encryption algorithm application example
to describe the appropriate algorithm in order to present security
technology that will have no negative impact on the quality of the
video phone service.
Abstract: We investigated the effects of modified
preprogrammed training mode Chase Trainer from Balance Trainer
(BT3, HurLab, Tampere, Finland) on athlete who experienced
unilateral Patellofemoral Pain Syndrome (PFPS). Twenty-seven
athletes with mean age= 14.23 ±1.31 years, height = 164.89 ± 7.85
cm, weight = 56.94 ± 9.28 kg were randomly assigned to two groups:
experiment (EG; n = 14) and injured (IG; n = 13). EG performed a
series of Chase Trainer program which required them to shift their
body weight at different directions, speeds and angle of leaning twice
a week for duration of 8 weeks. The static postural control and
perceived pain level measures were taken at baseline, after 6 weeks
and 8 weeks of training. There was no significant difference in any of
tested variables between EG and IG before and after 6-week the
intervention period. However, after 8-week of training, the postural
control (eyes open) and perceived pain level of EG improved
compared to IG (p
Abstract: Effective cooling of electronic equipment has emerged
as a challenging and constraining problem of the new century. In the
present work the feasibility and effectiveness of jet impingement
cooling on electronics were investigated numerically and
experimentally. Studies have been conducted to see the effect of the
geometrical parameters such as jet diameter (D), jet to target
spacing (Z) and ratio of jet spacing to jet diameter (Z/D) on the heat
transfer characteristics. The values of Reynolds numbers considered
are in the range 7000 to 42000. The results obtained from the
numerical studies are validated by conducting experiments. From the
studies it is found that the optimum value of Z/D ratio is 5. For a
given Reynolds number, the Nusselt number increases by about 28%
if the diameter of the nozzle is increased from 1mm to 2mm.
Correlations are proposed for Nusselt number in terms of Reynolds
number and these are valid for air as the cooling medium.