Abstract: This paper describes design of a digital feedback loop
for a low switching frequency dc-dc switching converters. Low
switching frequencies were selected in this design. A look up table
for the digital PID (proportional integrator differentiator)
compensator was implemented using Altera Stratix II with built-in
ADC (analog-to-digital converter) to achieve this hardware
realization. Design guidelines are given for the PID compensator,
high frequency DPWM (digital pulse width modulator) and moving
average filter.
Abstract: The purpose of study is to demonstrate how the characteristics of technology and the process required for development of technology affect technology transfer from public organisations to industry on the technology level. In addition, using the advantage of the analytic level and the novel means of measuring technology convergence, we examine the characteristics of converging technologies as compared to non-converging technologies in technology transfer process. In sum, our study finds that a technology from the public sector is likely to be transferred when its readiness level is closer to generation of profit, when its stage of life cycle is early and when its economic values is high. Our findings also show that converging technologies are less likely to be transferred.
Abstract: This paper presents a 24 watts SEPIC converter design
and control using microprocessor. SEPIC converter has advantages of
a wide input range and miniaturization caused by the low stress at
elements. There is also an advantage that the input and output are
isolated in MOSFET-off state. This paper presents the PID control
through the SEPIC converter transfer function using a DSP and the
protective circuit for fuel cell from the over-current and
inverse-voltage by using the characteristic of SEPIC converter. Then it
derives them through the experiments.
Abstract: The innovative fuzzy estimator is used to estimate the
ground motion acceleration of the retaining structure in this study. The
Kalman filter without the input term and the fuzzy weighting recursive
least square estimator are two main portions of this method. The
innovation vector can be produced by the Kalman filter, and be
applied to the fuzzy weighting recursive least square estimator to
estimate the acceleration input over time. The excellent performance
of this estimator is demonstrated by comparing it with the use of
difference weighting function, the distinct levels of the measurement
noise covariance and the initial process noise covariance. The
availability and the precision of the proposed method proposed in this
study can be verified by comparing the actual value and the one
obtained by numerical simulation.
Abstract: Microarray experiments are information rich; however, extensive data mining is required to identify the patterns that characterize the underlying mechanisms of action. For biologists, a key aim when analyzing microarray data is to group genes based on the temporal patterns of their expression levels. In this paper, we used an iterative clustering method to find temporal patterns of gene expression. We evaluated the performance of this method by applying it to real sporulation data and simulated data. The patterns obtained using the iterative clustering were found to be superior to those obtained using existing clustering algorithms.
Abstract: Renewable natural fibres such as oil palm, flax, and
pineapple leaf can be utilized to obtain new high performance
polymer materials. The reuse of waste natural fibres as reinforcement
for polymer is a sustainable option to the environment. However, due
to its high hydroxyl content of cellulose, natural fibres are
susceptible to absorb water that affects the composite mechanical
properties adversely. Research found that Nano materials such as
Nano Silica Carbide (n-SiC) and Nano Clay can be added into the
polymer composite to overcome this problem by enhancing its
mechanical properties in wet condition. The addition of Nano
material improves the tensile and wear properties, flexural stressstrain
behaviour, fracture toughness, and fracture strength of polymer
natural composites in wet and dry conditions.
Abstract: This study aims to assess the vulnerability and risk of
the coastal areas of Taijiang to abnormal oceanographic phenomena.
In addition, this study aims to investigate and collect data regarding
the disaster losses, land utilization, and other social, economic, and
environmental issues in these coastal areas to construct a coastal
vulnerability and risk map based on the obtained climate-change risk
assessment results. Considering the indexes of the three coastal
vulnerability dimensions, namely, man-made facilities, environmental
geography, and social economy, this study adopted the equal
weighting process and Analytic Hierarchy Process to analyze the
vulnerability of these coastal areas to disasters caused by climatic
changes. Among the areas with high coastal vulnerability to climatic
changes, three towns had the highest coastal vulnerability and four had
the highest relative vulnerability. Areas with lower disaster risks were
found to be increasingly vulnerable to disasters caused by climatic
changes as time progresses.
Abstract: Monoculture and mixed cultures of microalgae and
the oleaginous yeast for microbial oil productions were investigated
using sugarcane juice as carbon substrate. The monoculture of yeast
Torulaspora maleeae Y30, Torulaspora globosa YU5/2 grew faster
than that of microalgae Chlorella sp. KKU-S2. In monoculture of T.
maleeae Y30, a biomass of 8.267g/L with lipid yield of 0.920g/L
were obtained, while 8.333g/L of biomass with lipid yield of
1.141g/L were obtained for monoculture of T. globosa YU5/2. A
biomass of 1.933g/L with lipid yield of 0.052g/L was found for
monoculture of Chlorella sp. KKU-S2. The biomass concentration in
the mixed culture of the oleaginous yeast with microalgae increased
faster and was higher compared with that in the monocultures. A
biomass of 8.733g/L with lipid yield of 1.564g/L was obtained for a
mixed culture of T. maleeae Y30 with Chlorella sp. KKU-S2, while
8.010g/L of biomass with lipid yield of 2.424g/L was found for
mixed culture of T. globosa YU5/2 with Chlorella sp. KKU-S2.
Maximum cell yield coefficient (YX/S, g/L) was found of 0.323 in
monoculture of Chlorella sp. KKU-S2 but low level of both specific
yield of lipid (YP/X, g lipid/g cells) of 0.027 and volumetric lipid
production rate (QP, g/L/d) of 0.003 were observed. While, maximum
YP/X (0.303), QP (0.105) and maximum process product yield (YP/S,
0.061) were obtained in mixed culture of T. globosa YU5/2 with
Chlorella sp. KKU-S2. The results obtained from the study shows
that mixed culture of yeast with microalgae is a desirable cultivation
process for microbial oil production.
Abstract: In this paper, a neural network technique is applied to
real-time classifying media while a projectile is penetrating through
them. A laboratory-scaled penetrating setup was built for the
experiment. Features used as the network inputs were extracted from
the acceleration of penetrator. 6000 set of features from a single
penetration with known media and status were used to train the neural
network. The trained system was tested on 30 different penetration
experiments. The system produced an accuracy of 100% on the
training data set. And, their precision could be 99% for the test data
from 30 tests.
Abstract: Wireless capsule Endoscopy (WCE) has rapidly
shown its wide applications in medical domain last ten years
thanks to its noninvasiveness for patients and support for thorough
inspection through a patient-s entire digestive system including
small intestine. However, one of the main barriers to efficient
clinical inspection procedure is that it requires large amount of
effort for clinicians to inspect huge data collected during the
examination, i.e., over 55,000 frames in video. In this paper, we
propose a method to compute meaningful motion changes of
WCE by analyzing the obtained video frames based on regional
optical flow estimations. The computed motion vectors are used to
remove duplicate video frames caused by WCE-s imaging nature,
such as repetitive forward-backward motions from peristaltic
movements. The motion vectors are derived by calculating
directional component vectors in four local regions. Our
experiments are performed on small intestine area, which is of
main interest to clinical experts when using WCEs, and our
experimental results show significant frame reductions comparing
with a simple frame-to-frame similarity-based image reduction
method.
Abstract: Although silicon photonic devices provide a significantly larger bandwidth and dissipate a substantially less power than the electronic devices, they suffer from a large size due to the fundamental diffraction limit and the weak optical response of Si. A potential solution is to exploit Si plasmonics, which may not only miniaturize the photonic device far beyond the diffraction limit, but also enhance the optical response in Si due to the electromagnetic field confinement. In this paper, we discuss and summarize the recently developed metal-insulator-Si-insulator-metal nanoplasmonic waveguide as well as various passive and active plasmonic components based on this waveguide, including coupler, bend, power splitter, ring resonator, MZI, modulator, detector, etc. All these plasmonic components are CMOS compatible and could be integrated with electronic and conventional dielectric photonic devices on the same SOI chip. More potential plasmonic devices as well as plasmonic nanocircuits with complex functionalities are also addressed.
Abstract: An experimental and simulation flight test has been carried out to evaluate the longitudinal gliding characteristics of a lifting body with blunted half-cone geometry. The novelty here is the lifting body's pitch control mechanism, which consists of a pair of leading-edge rotating cylinders. Flight simulation uses aerodynamic data from computational fluid dynamics supported by wind-tunnel test. Flight test consists of releasing an aluminum lifting body model from a moving vehicle at the appropriate wind speed while measuring the lifting body's variation of altitude against time of flight. Results show that leading-edge rotating cylinder is able to give small amounts of improvement to the longitudinal stability and pitch control to the lifting body.
Abstract: With the globalized production and logistics
environment, the need for reducing the product development interval
and lead time, having a faster response to orders, conforming to quality
standards, fair tracking, and boosting information exchanging
activities with customers and partners, and coping with changes in the
management environment, manufacturers are in dire need of an
information management system in their manufacturing environments.
There are lots of information systems that have been designed to
manage the condition or operation of equipment in the field but
existing systems have a decentralized architecture, which is not
unified. Also, these systems cannot effectively handle the status data
extraction process upon encountering a problem related to protocols or
changes in the equipment or the setting. In this regard, this paper will
introduce a system for processing and saving the status info of
production equipment, which uses standard representation formats, to
enable flexible responses to and support for variables in the field
equipment. This system can be used for a variety of manufacturing and
equipment settings and is capable of interacting with higher-tier
systems such as MES.
Abstract: An additive fuzzy system comprising m rules with
n inputs and p outputs in each rule has at least t m(2n + 2 p + 1)
parameters needing to be tuned. The system consists of a large
number of if-then fuzzy rules and takes a long time to tune its
parameters especially in the case of a large amount of training data
samples. In this paper, a new learning strategy is investigated to cope
with this obstacle. Parameters that tend toward constant values at the
learning process are initially fixed and they are not tuned till the end
of the learning time. Experiments based on applications of the
additive fuzzy system in function approximation demonstrate that the
proposed approach reduces the learning time and hence improves
convergence speed considerably.
Abstract: This paper presents an optimization of the hull
separation, i.e. transverse clearance. The main objective is to identify
the feasible speed ranges and find the optimum transverse clearance
considering the minimum wave-making resistance. The dimensions
and the weight of hardware systems installed in the catamaran
structured fuel cell powered USV (Unmanned Surface Vehicle) were
considered as constraints. As the CAE (Computer Aided Engineering)
platform FRIENDSHIP-Framework was used. The hull surface
modeling, DoE (Design of Experiment), Tangent search optimization,
tool integration and the process automation were performed by
FRIENDSHIP-Framework. The hydrodynamic result was evaluated
by XPAN the potential solver of SHIPFLOW.
Abstract: The adaptive power control of Code Division Multiple
Access (CDMA) communications using Remote Radio Head
(RRH) between multiple Unmanned Aerial Vehicles (UAVs) with
a link-budget based Signal-to-Interference Ratio (SIR) estimate is
applied to four inner loop power control algorithms. It is concluded
that Base Station (BS) can calculate not only UAV distance using
linearity between speed and Consecutive Transmit-Power-Control
Ratio (CTR) of Adaptive Step-size Closed Loop Power Control (ASCLPC),
Consecutive TPC Ratio Step-size Closed Loop Power Control
(CS-CLPC), Fixed Step-size Power Control (FSPC), but also UAV
position with Received Signal Strength Indicator (RSSI) ratio of
RRHs.
Abstract: This paper investigates experimental studies on
vibration suppression for a cantilever beam using an
Electro-Rheological (ER) sandwich shock absorber. ER fluid (ERF) is a
class of smart materials that can undergo significant reversible changes
immediately in its rheological and mechanical properties under the
influence of an applied electric field. Firstly, an ER sandwich beam is
fabricated by inserting a starch-based ERF into a hollow composite
beam. At the same time, experimental investigations are focused on the
frequency response of the ERF sandwich beam. Second, the ERF
sandwich beam is attached to a cantilever beam to become as a shock
absorber. Finally, a fuzzy semi-active vibration control is designed to
suppress the vibration of the cantilever beam via the ERF sandwich
shock absorber. To check the consistency of the proposed fuzzy
controller, the real-time implementation validated the performance of
the controller.
Abstract: In a previous work, we presented the numerical
solution of the two dimensional second order telegraph partial
differential equation discretized by the centred and rotated five-point
finite difference discretizations, namely the explicit group (EG) and
explicit decoupled group (EDG) iterative methods, respectively. In
this paper, we utilize a domain decomposition algorithm on these
group schemes to divide the tasks involved in solving the same
equation. The objective of this study is to describe the development
of the parallel group iterative schemes under OpenMP programming
environment as a way to reduce the computational costs of the
solution processes using multicore technologies. A detailed
performance analysis of the parallel implementations of points and
group iterative schemes will be reported and discussed.
Abstract: The wireless sensor networks have been extensively
deployed and researched. One of the major issues in wireless sensor
networks is a developing energy-efficient clustering protocol.
Clustering algorithm provides an effective way to prolong the lifetime
of a wireless sensor networks. In the paper, we compare several
clustering protocols which significantly affect a balancing of energy
consumption. And we propose an Energy-Efficient Distributed
Unequal Clustering (EEDUC) algorithm which provides a new way of
creating distributed clusters. In EEDUC, each sensor node sets the
waiting time. This waiting time is considered as a function of residual
energy, number of neighborhood nodes. EEDUC uses waiting time to
distribute cluster heads. We also propose an unequal clustering
mechanism to solve the hot-spot problem. Simulation results show that
EEDUC distributes the cluster heads, balances the energy
consumption well among the cluster heads and increases the network
lifetime.
Abstract: Compared to oil production from microorganisms, little work has been performed for mixed culture of microalgae and yeast. In this article it is aimed to show high oil accumulation potential of mixed culture of microalgae Chlorella sp. KKU-S2 and oleaginous yeast Torulaspora maleeae Y30 using sugarcane molasses as substrate. The monoculture of T. maleeae Y30 grew faster than that of microalgae Chlorella sp. KKU-S2. In monoculture of yeast, a biomass of 6.4g/L with specific growth rate (m) of 0.265 (1/d) and lipid yield of 0.466g/L were obtained, while 2.53g/L of biomass with m of 0.133 (1/d) and lipid yield of 0.132g/L were obtained for monoculture of Chlorella sp. KKU-S2. The biomass concentration in the mixed culture of T. maleeae Y30 with Chlorella sp. KKU-S2 increased faster and was higher compared with that in the monoculture and mixed culture of microalgae. In mixed culture of microalgae Chlorella sp. KKU-S2 and C. vulgaris TISTR8580, a biomass of 3.47g/L and lipid yield of 0.123 g/L were obtained. In mixed culture of T. maleeae Y30 with Chlorella sp. KKU-S2, a maximum biomass of 7.33 g/L and lipid yield of 0.808g/L were obtained. Maximum cell yield coefficient (YX/S, 0.229g/L), specific yield of lipid (YP/X, 0.11g lipid/g cells) and volumetric lipid production rate (QP, 0.115 g/L/d) were obtained in mixed culture of yeast and microalgae. Clearly, T. maleeae Y30 and Chlorella sp. KKU-S2 use sugarcane molasses as organic nutrients efficiently in mixed culture under mixotrophic growth. The biomass productivity and lipid yield are notably enhanced in comparison with monoculture.