Abstract: Hysteresis phenomenon has been observed in the
operations of both horizontal-axis and vertical-axis wind turbines
(HAWTs and VAWTs). In this study, wind tunnel experiments were
applied to investigate the characters of hysteresis phenomena between
the angular speed and the external resistance of electrical loading
during the operation of a Darrieus type VAWT. Data of output voltage,
output current, angular speed of wind turbine under different wind
speeds are measured and analyzed. Results show that the range of
external resistance changes with the wind speed. The range decreases
as the wind speed increases following an exponential decay form.
Experiments also indicate that the maximum output power of wind
turbines is always inside the range where hysteresis happened. These
results provide an important reference to the design of output control
system of wind turbines.
Abstract: This study was carried out experimentally and analytically about the performance of solar cell panel system for operating the pump coupled by dc-motor. The solar cell panel with total area 1.9848 m2 consists of three modules of 80 Wp each. The small centrifugal pump powered by dc-motor is operated to lift water from 1m to 7m heads in sequence and gives the amount of water pumped over the whole day from 08.00 to 16.00 h are 11988, 10851, 8874, 7695, 5760, 3600, 2340 L/d respectively. The hourly global solar radiation during the day is an average of 506 W/m2. This study also presents the I-V characteristics of the panel at global radiations 200, 400, 600, 800 and 1000 W/m2 matched with the operation of the pump at the above lifting heads. It proves that the only solar radiations 800 and 1000 W/m2 could provide lifting head from 1m to 7m. The analysis shows the best efficiency point of the performance of solar cell panel system occurs at the pumping head 2.89 m.
Abstract: Dynamic of phytoplankton blooms in the Baltic Sea
has been analyzed applying the numerical ecosystem model 3D
CEMBS. The model consists of the hydrodynamic model (POP,
version 2.1) and the ice model (CICE, version 4.0), which are
imposed by the atmospheric data model (DATM7). The 3D
model has an ecosystem module, activated in 2012 in the operational
mode. The ecosystem model consists of 11 main variables: biomass
of small-size phytoplankton and large-size phytoplankton
and cyanobacteria, zooplankton biomass, dissolved and molecular
detritus, dissolved oxygen concentration, as well as concentrations of
nutrients, including: nitrates, ammonia, phosphates and silicates. The
3D-CEMBS model is an effective tool for solving problems related to
phytoplankton blooms dynamic in the Baltic Sea
Abstract: Despite the availability of natural disaster related time series data for last 110 years, there is no forecasting tool available to humanitarian relief organizations to determine forecasts for emergency logistics planning. This study develops a forecasting tool based on identifying probability distributions. The estimates of the parameters are used to calculate natural disaster forecasts. Further, the determination of aggregate forecasts leads to efficient pre-disaster planning. Based on the research findings, the relief agencies can optimize the various resources allocation in emergency logistics planning.
Abstract: Five original strains of entomopathogenic bacteria
with insecticidal activity against mosquito larvae of the genera Aedes,
Culex and Anopheles have been isolated from natural conditions in
Armenia and characterized. According to morphological,
physiological and biochemical parameters, all isolates were identified
as Bacillus thuringiensis spp. israelensis (Bti). High larvicidal
activity has been showed by three strains Bti. These strains can be
recommended for industrial production of bacterial preparations.
Abstract: Understanding how precipitation inter-annually
changes and its implication in agricultural drought and production change in winter wheat (Triticum aestivum L.) growth season is critical for crop production in China. MODIS Temperature-Vegetation Dryness Index (TVDI) and daily mean precipitation time series for the main growth season(Feb. to May) of winter wheat from 2000 to 2010
were used to analyze the distribution of trends of precipitation,
agricultural drought and winter wheat yield change respectively, and
relationships between them in North China region(Huang-huai-hai
region, HHH region), China. The results indicated that the trend of
precipitation in HHH region past 11 years was increasing, which had
induced generally corresponding decreasing trend of agricultural
drought and increasing trend of wheat yield, while the trend of drought
was spatially diverse. The study could provide a basis for agricultural
drought research during winter wheat season in HHH region under the
ground of climate change.
Abstract: This paper presents a speed sensorless direct torque
control scheme using space vector modulation (DTC-SVM) for
permanent magnet synchronous motor (PMSM) drive based a Model
Reference Adaptive System (MRAS) algorithm and stator resistance
estimator. The MRAS is utilized to estimate speed and stator
resistance and compensate the effects of parameter variation on stator
resistance, which makes flux and torque estimation more accurate
and insensitive to parameter variation. In other hand the use of SVM
method reduces the torque ripple while achieving a good dynamic
response. Simulation results are presented and show the effectiveness
of the proposed method.
Abstract: The fabrication of porous NiTi shape memory alloys (SMAs) from elemental powder compacts was conducted by selfpropagating high temperature synthesis (SHS). Effects of the preheating temperature and the chamber pressure on the combustion characteristics as well as the final morphology and the composition of products were studied. The samples with porosity between 56.4 and 59.0% under preheating temperature in the range of 200-300°C and Ar-gas chamber pressure of 138 and 201 kPa were obtained. The pore structures were found to be dissimilar only in the samples processed with different preheating temperature. The major phase in the porous product is NiTi with small amounts of secondary phases, NiTi2 and Ni4Ti3. The preheating temperature and the chamber pressure have very little effect on the phase constituent. While the combustion temperature of the sample was notably increased by increasing the preheating temperature, they were slightly changed by varying the chamber pressure.
Abstract: There is a growing interest in the food industry and in preventive health care for the development and evaluation of natural antioxidants from medicinal plant materials. In the present work, extracts of three medicinal plants (Tilia argentea, Crataegi folium leaves and Polygonum bistorta roots) used in Turkish phytotheraphy were screened for their phenolic profiles and antioxidant properties. Crude extracts were obtained from different parts of plants, by solidliquid extraction with pure water, 70% acetone and 70% methanol aqueous solvents. The antioxidant activity of the extracts was determined by ABTS.+ radical cation scavenging activity. The Folin Ciocalteu procedure was used to assess the total phenolic concentrations of the extracts as gallic acid equivalents. A modified liquid chromatography-electro spray ionization-mass spectrometry (LC-ESI-MS) was used to obtain chromatographic profiles of the phenolic compounds in the medicinal plants. The predominant phenolic compounds detected in different extracts of the plants were catechin, protocatechuic and chlorogenic acids. The highest phenolic contents were obtained by using 70% acetone as aqueous solvent, whereas the lowest phenolic contents were obtained by water extraction due to Folin Ciocalteu results. The results indicate that acetone extracts of Tilia argentea had the highest antioxidant capacity as free ABTS radical scavengers. The lowest phenolic contents and antioxidant capacities were obtained from Polygonum bistorta root extracts.
Abstract: More and more natural disasters are happening every
year: floods, earthquakes, volcanic eruptions, etc. In order to reduce
the risk of possible damages, governments all around the world are
investing into development of Early Warning Systems (EWS) for
environmental applications. The most important task of the EWS is
identification of the onset of critical situations affecting environment
and population, early enough to inform the authorities and general
public. This paper describes an approach for monitoring of flood
protections systems based on machine learning methods. An
Artificial Intelligence (AI) component has been developed for
detection of abnormal dike behaviour. The AI module has been
integrated into an EWS platform of the UrbanFlood project (EU
Seventh Framework Programme) and validated on real-time
measurements from the sensors installed in a dike.
Abstract: This study aimed to evaluate the muscularity and tissue composition of 24 legs of Ile de France lambs. They were fed with diets containing “in nature" or hydrolyzed sugarcane with 0.6% of calcium oxide in aerobic and anaerobic environments. Animals entered the trial at 15 and were slaughtered at 32 kg of body weight. The leg tissue composition, as well as muscularity (0.47), muscle:bone (6.66) and muscle:fat (4.25) were not affected (P>0.05) by treatments. The proportions found were: 67.62% for muscle, 17.52% for bone and 10.15% for fat. In relation to lambs fed with “in nature" sugarcane, hydrolyzed sugarcane with calcium oxide in aerobic and anaerobic environments did not affect muscularity and leg tissue composition of lambs.
Abstract: MRAM technology provides a combination of fast
access time, non-volatility, data retention and endurance. While a
growing interest is given to two-terminal Magnetic Tunnel Junctions
(MTJ) based on Spin-Transfer Torque (STT) switching as the
potential candidate for a universal memory, its reliability is
dramatically decreased because of the common writing/reading path.
Three-terminal MTJ based on Spin-Orbit Torque (SOT) approach
revitalizes the hope of an ideal MRAM. It can overcome the
reliability barrier encountered in current two-terminal MTJs by
separating the reading and the writing path. In this paper, we study
two possible writing schemes for the SOT-MTJ device based on
recently fabricated samples. While the first is based on precessional
switching, the second requires the presence of permanent magnetic
field. Based on an accurate Verilog-A model, we simulate the two
writing techniques and we highlight advantages and drawbacks of
each one. Using the second technique, pioneering logic circuits based
on the three-terminal architecture of the SOT-MTJ described in this
work are under development with preliminary attractive results.
Abstract: The goal of Gene Expression Analysis is to understand the processes that underlie the regulatory networks and pathways controlling inter-cellular and intra-cellular activities. In recent times microarray datasets are extensively used for this purpose. The scope of such analysis has broadened in recent times towards reconstruction of gene networks and other holistic approaches of Systems Biology. Evolutionary methods are proving to be successful in such problems and a number of such methods have been proposed. However all these methods are based on processing of genotypic information. Towards this end, there is a need to develop evolutionary methods that address phenotypic interactions together with genotypic interactions. We present a novel evolutionary approach, called Phenomic algorithm, wherein the focus is on phenotypic interaction. We use the expression profiles of genes to model the interactions between them at the phenotypic level. We apply this algorithm to the yeast sporulation dataset and show that the algorithm can identify gene networks with relative ease.
Abstract: The first and basic cause of the failure of concrete is repeated freezing (thawing) of moisture contained in the pores, microcracks, and cavities of the concrete. On transition to ice, water existing in the free state in cracks increases in volume, expanding the recess in which freezing occurs. A reduction in strength below the initial value is to be expected and further cycle of freezing and thawing have a further marked effect. By using some experimental parameters like nuclear magnetic resonance variation (NMR), enthalpy-temperature (or heat capacity) variation, we can resolve between the various water states and their effect on concrete properties during cooling through the freezing transition temperature range. The main objective of this paper is to describe the principal type of water responsible for the reduction in strength and structural damage (frost damage) of concrete following repeated freeze –thaw cycles. Some experimental work was carried out at the institute of cryogenics to determine what happens to water in concrete during the freezing transition.
Abstract: Expression data analysis is based mostly on the
statistical approaches that are indispensable for the study of
biological systems. Large amounts of multidimensional data resulting
from the high-throughput technologies are not completely served by
biostatistical techniques and are usually complemented with visual,
knowledge discovery and other computational tools. In many cases,
in biological systems we only speculate on the processes that are
causing the changes, and it is the visual explorative analysis of data
during which a hypothesis is formed. We would like to show the
usability of multidimensional visualization tools and promote their
use in life sciences. We survey and show some of the
multidimensional visualization tools in the process of data
exploration, such as parallel coordinates and radviz and we extend
them by combining them with the self-organizing map algorithm. We
use a time course data set of transitional cell carcinoma of the bladder
in our examples. Analysis of data with these tools has the potential to
uncover additional relationships and non-trivial structures.
Abstract: There are many sources trough which the soil get
enriched and contaminated with REEs. The determination of REEs in
environmental samples has been limited because of the lack of
sensitive analytical techniques. Soil samples were collected from
four sites including open cast coal mine, natural coal burning, coal
washery and control in the coal field located in Dhanbad, India.
Total concentrations of rare earth elements (REEs) were determined
using the inductively coupled plasma atomic absorption spectrometry
in order to assess enrichment status in the coal field. Results showed
that the mean concentrations of La, Pr, Eu, Tb, Ho, and Tm in open
cast mine and natural coal burning sites were elevated compared to
the reference concentrations, while Ce, Nd, Sm, and Gd were
elevated in coal washery site. When compared to reference soil,
heavy REEs (HREEs) were enriched in open cast mines and natural
coal burning affected soils, however, the HREEs were depleted in the
coal washery sites. But, the Chondrite-normalization diagram showed
significant enrichment for light REEs (LREEs) in all the soils. High
concentration of Pr, Eu, Tb, Ho, Tm, and Lu in coal mining and coal
burning sites may pose human health risks. Factor analysis showed
that distribution and relative abundance of REEs of the coal washery
site is comparable with the control. Eventually washing or cleaning
of coal could significantly decrease the emission of REEs from coal
into the environment.
Abstract: This paper focuses on Land Use and Land Cover Changes (LULCC) occurred in the urban coastal regions of the Mediterranean basin in the last thirty years. LULCC were assessed diachronically (1975-2006) in two urban areas, Rome (Italy) and Athens (Greece), by using CORINE land cover maps. In strictly coastal territories a persistent growth of built-up areas at the expenses of both agricultural and forest land uses was found. On the contrary, a different pattern was observed in the surrounding inland areas, where a high conversion rate of the agricultural land uses to both urban and forest land uses was recorded. The impact of city growth on the complex pattern of coastal LULCC is finally discussed.
Abstract: In this paper the use of sequential machines for recognizing actions taken by the objects detected by a general tracking algorithm is proposed. The system may deal with the uncertainty inherent in medium-level vision data. For this purpose, fuzzification of input data is performed. Besides, this transformation allows to manage data independently of the tracking application selected and enables adding characteristics of the analyzed scenario. The representation of actions by means of an automaton and the generation of the input symbols for finite automaton depending on the object and action compared are described. The output of the comparison process between an object and an action is a numerical value that represents the membership of the object to the action. This value is computed depending on how similar the object and the action are. The work concludes with the application of the proposed technique to identify the behavior of vehicles in road traffic scenes.
Abstract: Graph coloring is an important problem in computer
science and many algorithms are known for obtaining reasonably
good solutions in polynomial time. One method of comparing
different algorithms is to test them on a set of standard graphs where
the optimal solution is already known. This investigation analyzes a
set of 50 well known graph coloring instances according to a set of
complexity measures. These instances come from a variety of
sources some representing actual applications of graph coloring
(register allocation) and others (mycieleski and leighton graphs) that
are theoretically designed to be difficult to solve. The size of the
graphs ranged from ranged from a low of 11 variables to a high of
864 variables. The method used to solve the coloring problem was
the square of the adjacency (i.e., correlation) matrix. The results
show that the most difficult graphs to solve were the leighton and the
queen graphs. Complexity measures such as density, mobility,
deviation from uniform color class size and number of block
diagonal zeros are calculated for each graph. The results showed that
the most difficult problems have low mobility (in the range of .2-.5)
and relatively little deviation from uniform color class size.
Abstract: The machining performance is determined by the
frequency characteristics of the machine-tool structure and the
dynamics of the cutting process. Therefore, the prediction of dynamic
vibration behavior of spindle tool system is of great importance for the
design of a machine tool capable of high-precision and high-speed
machining. The aim of this study is to develop a finite element model
to predict the dynamic characteristics of milling machine tool and
hence evaluate the influence of the preload of the spindle bearings. To
this purpose, a three dimensional spindle bearing model of a high
speed engraving spindle tool was created. In this model, the rolling
interfaces with contact stiffness defined by Harris model were used to
simulate the spindle bearing components. Then a full finite element
model of a vertical milling machine was established by coupling the
spindle tool unit with the machine frame structure. Using this model,
the vibration mode that had a dominant influence on the dynamic
stiffness was determined. The results of the finite element simulations
reveal that spindle bearing with different preloads greatly affect the
dynamic behavior of the spindle tool unit and hence the dynamic
responses of the vertical column milling system. These results were
validated by performing vibration on the individual spindle tool unit
and the milling machine prototype, respectively. We conclude that
preload of the spindle bearings is an important component affecting
the dynamic characteristics and machining performance of the entire
vertical column structure of the milling machine.