Abstract: This paper proposes two types of non-isolated
direct AC-DC converters. First, it shows a buck-boost
converter with an H-bridge, which requires few components
(three switches, two diodes, one inductor and one capacitor) to
convert AC input to DC output directly. This circuit can handle
a wide range of output voltage. Second, a direct AC-DC buck
converter is proposed for lower output voltage applications.
This circuit is analyzed with output voltage of 12V. We
describe circuit topologies, operation principles and simulation
results for both circuits.
Abstract: The study of the fouling deposition of pink guava
juice (PGJ) is relatively new research compared to milk fouling
deposit. In this work, a new experimental set-up was developed to
imitate the fouling formation in heat exchanger, namely a continuous
flow experimental set-up heat exchanger. The new experimental setup
was operated under industrial pasteurization temperature of PGJ,
which was at 93°C. While the flow rate and pasteurization period
were based on the experimental capacity, which were 0.5 and 1
liter/min for the flow rate and the pasteurization period was set for 1
hour. Characterization of the fouling deposit was determined by
using various methods. Microstructure of the deposits was carried
out using ESEM. Proximate analyses were performed to determine
the composition of moisture, fat, protein, fiber, ash and carbohydrate
content. A study on the hardness and stickiness of the fouling deposit
was done using a texture analyzer. The presence of seedstone in pink
guava juice was also analyzed using a particle analyzer. The findings
shown that seedstone from pink guava juice ranging from 168 to
200μm and carbohydrate was found to be a major composition
(47.7% of fouling deposit consists of carbohydrate). Comparison
between the hardness and stickiness of the deposits at two different
flow rates showed that fouling deposits were harder and denser at
higher flow rate. Findings from this work provide basis knowledge
for further study on fouling and cleaning of PGJ.
Abstract: All over the world, including the Middle and East
European countries, sustainable tillage and sowing technologies are
applied increasingly broadly with a view to optimising soil resources,
mitigating soil degradation processes, saving energy resources,
preserving biological diversity, etc. As a result, altered conditions of
tillage and sowing technological processes are faced inevitably. The
purpose of this study is to determine the seedbed topsoil hardness
when using a combined sowing coulter in different sustainable tillage
technologies. The research involved a combined coulter consisting
of two dissected blade discs and a shoe coulter. In order to determine
soil hardness at the seedbed area, a multipenetrometer was used. It
was found by experimental studies that in loosened soil, a combined
sowing coulter equally suppresses the furrow bottom, walls and soil
near the furrow; therefore, here, soil hardness was similar at all
researched depths and no significant differences were established. In
loosened and compacted (double-rolled) soil, the impact of a
combined coulter on the hardness of seedbed soil surface was more
considerable at a depth of 2 mm. Soil hardness at the furrow bottom
and walls to a distance of up to 26 mm was 1.1 MPa. At a depth of 10
mm, the greatest hardness was established at the furrow bottom. In
loosened and heavily compacted (rolled for 6 times) soil, at a depth
of 2 and 10 mm a combined coulter most of all compacted the furrow
bottom, which has a hardness of 1.8 MPa. At a depth of 20 mm, soil
hardness within the whole investigated area varied insignificantly and
fluctuated by around 2.0 MPa. The hardness of furrow walls and soil
near the furrow was by approximately 1.0 MPa lower than that at the
furrow bottom
Abstract: Ireland developed a National Strategy 2030 that
argued for the creation of a new form of higher education institution,
a Technological University. The research reported here reviews the
first stage of this partnership development. The study found that
national policy can create system capacity and change, but that
individual partners may have more to gain or lose in collaborating.
When presented as a zero-sum activity, fear among partners is high.
The level of knowledge and networking within the higher education
system possessed by each partner contributed to decisions to
participate or not in a joint proposal for collaboration. Greater
success resulted when there were gains for all partners. This research
concludes that policy mandates can provide motivation to
collaborate, but that the partnership needs to be built more on shared
values versus coercion by mandates.
Abstract: Product Lead Time (PLT) is the period of time from
receiving a customer's order to delivering the final product. PLT is an
indicator of the manufacturing controllability, efficiency and
performance. Due to the explosion in the rate of technological
innovations and the rapid changes in the nature of manufacturing
processes, manufacturing firms can bring the new products to market
quicker only if they can reduce their PLT and speed up the rate at
which they can design, plan, control, and manufacture. Although
there is a substantial body of research on manufacturing relating to
cost and quality issues, there is no much specific research conducted
in relation to the formulation of PLT, despite its significance and
importance. This paper analyzes and formulates PLT which can be
used as a guideline for achieving the shorter PLT. Further more this
paper identifies the causes of delay and factors that contributes to the
increased product lead-time.
Abstract: The manufacture of large-scale precision aerospace
components using CNC requires a highly effective maintenance
strategy to ensure that the required accuracy can be achieved over
many hours of production. This paper reviews a strategy for a
maintenance management system based on Failure Mode Avoidance,
which uses advanced techniques and technologies to underpin a
predictive maintenance strategy. It is shown how condition
monitoring (CM) is important to predict potential failures in high
precision machining facilities and achieve intelligent and integrated
maintenance management. There are two distinct ways in which CM
can be applied. One is to monitor key process parameters and
observe trends which may indicate a gradual deterioration of
accuracy in the product. The other is the use of CM techniques to
monitor high status machine parameters enables trends to be
observed which can be corrected before machine failure and
downtime occurs.
It is concluded that the key to developing a flexible and intelligent
maintenance framework in any precision manufacturing operation is
the ability to evaluate reliably and routinely machine tool condition
using condition monitoring techniques within a framework of Failure
Mode Avoidance.
Abstract: The introduction of sowing technologies into minimum- or no-tillage soil has a number of economical and environmental virtues, such as improving soil properties, decreasing soil erosion and degradation, and saving working time and fuel. However, the main disadvantage of these technologies is that plant residues on the soil surface reduce the quality of the planted crop seeds, thus requiring plant residues to be removed or cut. This paper presents a analysis of disc coulter parameters and an experimental investigation of cutting spring barley straw containing various amounts of moisture with different disc coulters (smooth and notched).
Abstract: Since the late 1980s, the new phenomena of 'employment subcentres' or 'polycentricity' has appeared in the metropolises of North American and Western Europe and it has been an interesting topic for academics and researchers. This paper specifically uses one case study-Guangzhou to explore the development and the mechanism of employment subcentres and polycentricity in Chinese metropolises by spatial analysis method on the basis of the first economic census data. In conclusion, the paper regards that the employment subcentres and polycentricity has existed in Chinese metropolises. And that, the mechanism of them is mainly from the secondary industry instead of the tertiary industry in North American and Western Europe
Abstract: Within the collaborative research center 666 a new
product development approach and the innovative manufacturing
method of linear flow splitting are being developed. So far the design process is supported by 3D-CAD models utilizing User Defined
Features in standard CAD-Systems. This paper now presents new
functions for generating 3D-models of integral sheet metal products with bifurcations using Siemens PLM NX 6. The emphasis is placed
on design and semi-automated insertion of User Defined Features.
Therefore User Defined Features for both, linear flow splitting
and its derivative linear bend splitting, were developed. In order to facilitate the modeling process, an application was developed
that guides through the insertion process. Its usability and dialog layout adapt known standard features. The work presented here has
significant implications on the quality, accurateness and efficiency of the product generation process of sheet metal products with higher
order bifurcations.
Abstract: This work relates the development of an optical fiber
(OF) sensor for the detection and quantification of single walled
carbon nanotubes in aqueous solutions. The developed OF displays a
compact design, it requires less expensive materials and equipment
as well as low volume of sample (0.2 mL). This methodology was
also validated by the comparison of its analytical performance with
that of a standard methodology based on ultraviolet-visible
spectroscopy. The developed OF sensor follows the general SDS
calibration proposed for OF sensors as a more suitable calibration
fitting compared with classical calibrations.
Abstract: Excilamps are new UV sources with great potential
for application in wastewater treatment. In the present work, a XeBr
excilamp emitting radiation at 283 nm has been used for the
photodegradation of 4-chlorophenol within a range of concentrations
from 50 to 500 mg L-1. Total removal of 4-chlorophenol was
achieved for all concentrations assayed. The two main photoproduct
intermediates formed along the photodegradation process,
benzoquinone and hydroquinone, although not being completely
removed, remain at very low residual concentrations. Such
concentrations are insignificant compared to the 4-chlorophenol
initial ones and non-toxic. In order to simulate the process and scaleup,
a kinetic model has been developed and validated from the
experimental data.
Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.
Abstract: The main purpose of the research is to investigate the computer experiences and computer attitudes of prospective class teachers. The research also investigated the differences between computer attitudes and computer experiences, computer competencies and the influence of genders. Ninety prospective class teachers participated in the research. Computer Attitude Scale- Marmara (CAS-M), and a questionnaire, about their computer experiences, and opinions toward the use of computers in the classroom setting, were administrated. The major findings are as follows: (1) 62% of prospective class teachers have computer at home; (2) 50% of the computer owners have computers less than three years; (3) No significant differences were found between computer attitudes and gender; (4) Differences were found between general computer attitudes and computer liking attitudes of prospective class teachers based on their computer competencies in favor of more competent ones.
Abstract: Frequent machine breakdowns, low plant availability and increased overtime are a great threat to a manufacturing plant as they increase operating costs of an industry. The main aim of this study was to improve Overall Equipment Effectiveness (OEE) at a manufacturing company through the implementation of innovative maintenance strategies. A case study approach was used. The paper focuses on improving the maintenance in a manufacturing set up using an innovative maintenance regime mix to improve overall equipment effectiveness. Interviews, reviewing documentation and historical records, direct and participatory observation were used as data collection methods during the research. Usually production is based on the total kilowatt of motors produced per day. The target kilowatt at 91% availability is 75 Kilowatts a day. Reduced demand and lack of raw materials particularly imported items are adversely affecting the manufacturing operations. The company had to reset its targets from the usual figure of 250 Kilowatt per day to mere 75 per day due to lower availability of machines as result of breakdowns as well as lack of raw materials. The price reductions and uncertainties as well as general machine breakdowns further lowered production. Some recommendations were given. For instance, employee empowerment in the company will enhance responsibility and authority to improve and totally eliminate the six big losses. If the maintenance department is to realise its proper function in a progressive, innovative industrial society, then its personnel must be continuously trained to meet current needs as well as future requirements. To make the maintenance planning system effective, it is essential to keep track of all the corrective maintenance jobs and preventive maintenance inspections. For large processing plants these cannot be handled manually. It was therefore recommended that the company implement (Computerised Maintenance Management System) CMMS.
Abstract: Today due to rising levels of housing- necessities,
several problems have been raised regarding to urban quality of life.
The aim of the research is to study social and spatial aspects of
housing environment and to find out their interaction with the urban
quality of life. As a case of study two pilot areas of Famagusta city in
North Cyprus, were selected: Baykal, considered as an established
urban district and Tuzla, a newly developed peri-urban district. In
order to determine urban quality of life in planning and developing of
housing areas, social and spatial aspects of selected areas have been
examined, differences between them according to the planning policy
have been pointed out, advantages and disadvantages of housing
planning have been found. As a practical implementation of the
research a number of households in each selected area have been
interviewed in order to draw a conclusion.
Abstract: The possibility of producing drinking water from
brackish ground water using Vacuum membrane distillation (VMD)
process was studied. It is a rising technology for seawater or brine
desalination process. The process simply consists of a flat sheet
hydrophobic micro porous PTFE membrane and diaphragm vacuum
pump without a condenser for the water recovery or trap. In this
work, VMD performance was investigated for aqueous NaCl solution
and natural ground water. The influence of operational parameters
such as feed flow rate (30 to 55 l/h), feed temperature (313 to 333 K),
feed salt concentration (5000 to 7000 mg/l) and permeate pressure
(1.5 to 6 kPa) on the membrane distillation (MD) permeation flux
have been investigated. The maximum flux reached to 28.34 kg/m2 h
at feed temperature, 333 K; vacuum pressure, 1.5 kPa; feed flow rate,
55 l/h and feed salt concentration, 7000 mg/l. The negligible effects
in the reduction of permeate flux found over 150 h experimental run
for salt water. But for the natural ground water application over 75 h,
scale deposits observed on the membrane surface and 29% reduction
in the permeate flux over 75 h. This reduction can be eliminated by
acidification of feed water. Hence, promote the research attention in
apply of VMD for the ground water purification over today-s
conventional RO operation.
Abstract: Introduction: Visual performance is an important factor in sport excellence. Visual involvement in a sport varies according to environmental demands associated with that sport. These environmental demands are matched by a task specific motor response. The purpose of this study was to determine if sport specific exercises will improve the visual performance of male rugby players, in order to achieve maximal results on the sports field. Materials & Methods: Twenty six adult male rugby players, aged 16-22, were chosen as subjects. In order to evaluate the effect of sport specific exercises on visual skills, a pre-test - post-test experimental group design was adopted for the study. Results: Significant differences (p≤0.05) were seen in the focussing, tracking, vergence, sequencing, eye-hand coordination and visualisation components Discussion & Conclusions: Sport specific exercises improved visual skills in rugby players which may provide them with an advantage over their opponents. This study suggests that these training programs and participation in regular on-line EyeDrills sports vision exercises (www.eyedrills.co.za) aimed at improving the athlete-s visual coordination, concentration, focus, hand-eye co-ordination, anticipation and motor response should be incorpotated in the rugby players exercise regime.
Abstract: A unique combination of adsorption and
electrochemical regeneration with a proprietary adsorbent material
called Nyex 100 was introduced at the University of Manchester for
waste water treatment applications. Nyex 100 is based on graphite
intercalation compound. It is non porous and electrically conducing
adsorbent material. This material exhibited very small BET surface
area i.e. 2.75 m2g-1, in consequence, small adsorptive capacities for
the adsorption of various organic pollutants were obtained. This work
aims to develop composite adsorbent material essentially capable of
electrochemical regeneration coupled with improved adsorption
characteristics. An organic dye, acid violet 17 was used as standard
organic pollutant. The developed composite material was
successfully electrochemically regenerated using a DC current of 1 A
for 60 minutes. Regeneration efficiency was maintained at around
100% for five adsorption-regeneration cycles.
Abstract: In response to address different development challenges, Tanzania is striving to achieve its fourth attribute of the National Development Vision, i.e. to have a well educated and learned society by the year 2025. One of the most cost effective methods that can reach a large part of the society in a short time is to integrate ICT in education through e-learning initiatives. However, elearning initiatives are challenged by limited or lack of connectivity to majority of secondary schools, especially those in rural and remote areas. This paper has explores the possibility for rural secondary school to access online e-Learning resources from a centralized e- Learning Management System (e-LMS). The scope of this paper is limited to schools that have computers irrespective of internet connectivity, resulting in two categories schools; those with internet access and those without. Different connectivity configurations have been proposed according to the ICT infrastructure status of the respective schools. However, majority of rural secondary schools in Tanzania have neither computers nor internet connection. Therefore this is a challenge to be addressed for the disadvantaged schools to benefit from e-Learning initiatives.
Abstract: The purpose of this study was to determine the
influence of physical activity and dietary fat intake on Body Mass
Index (BMI) of lecturers within a higher learning institutionalized
setting. The study adopted a Cross-sectional Correlational Design
and included 120 lecturers selected proportionately by simple
random sampling techniques from a population of 600 lecturers. Data
was collected using questionnaires, which had sections including
physical activity checklist adopted from the international physical
activity questionnaire (IPAQ), 24-hour food recall, anthropometric
measurements mainly weight and height. Analysis involved the use
of bivariate correlations and linear regression. A significant inverse
association was registered between BMI and duration (in minutes)
spent doing moderate intense physical activity per day (r=-0.322,
p