Abstract: The simple methods used to plan and measure non
patterned production system are developed from the basic definition
of working efficiency. Processing time is assigned as the variable
and used to write the equation of production efficiency.
Consequently, such equation is extensively used to develop the
planning method for production of interest using one-dimensional
stock cutting problem. The application of the developed method
shows that production efficiency and production planning can be
determined effectively.
Abstract: The efficiency of chitosan beads processed from 4
marine animal shells; white leg shrimp (Litopenaeus vannamei), mud
crab (Scylla sp.), horseshoe crab (Carcinoscorpius rotundicauda),
and cuttlefish bone (Sepia sp.), for the adsorption experiments of
ammonia and formaldehyde were investigated. The porosities of
chitosan from the shells looked like beads were distinctly examined
under SEM. The original pores of those shells on the surface areas
compose of evenly fine pores. The shell beads of cuttlefish bone and
horseshoe crab show the larger probably even porosity, while on
those white leg shrimp and mud crab contain various large and fine
pores. The best adsorption at pH 9 in 18 mg/l ammonia at 2 hours
yield on cuttlefish bone, horseshoe crab, mud crab and white leg
shrimp with the average percent of 59.12, 51.45, 45.66 and 43.52,
respectively. Within 30 minutes the formaldehyde absorbers (at pH 5
in 8 μg/ml) revealed 46.27, 26.56, and 18.04 percent capacities in
cuttlefish bone, mud crab and white leg shrimp beads; while 22.44
percent in the horseshoe crab at pH 7. The adsorption capacities and
the amounts of beads showed a positive correlation. The adsorption
capacity relationship between pH and the gas concentrations were
affected by these qualities of chitosan beads.
Abstract: Scatter behavior of fatigue life in die-cast AM60B
alloy was investigated. For comparison, those in rolled AM60B alloy
and die-cast A365-T5 aluminum alloy were also studied. Scatter
behavior of pore size was also investigated to discuss dominant
factors for fatigue life scatter in die-cast materials. Three-parameter
Weibull function was suitable to explain the scatter behavior of both
fatigue life and pore size. The scatter of fatigue life in die-cast
AM60B alloy was almost comparable to that in die-cast A365-T5
alloy, while it was significantly large compared to that in the rolled
AM60B alloy. Scatter behavior of pore size observed at fracture
nucleation site on the fracture surface was comparable to that
observed on the specimen cross-section and also to that of fatigue
life. Therefore, the dominant factor for large scatter of fatigue life in
die-cast alloys would be the large scatter of pore size. This
speculation was confirmed by the fracture mechanics fatigue life
prediction, where the pore observed at fatigue crack nucleation site
was assumed as the pre-existing crack.
Abstract: This paper aims to argue that religion and Faith-based
Organizations (FBOs) contribute to building democratic process
through the provision of education in Sierra Leone. Sierra Leone
experienced a civil war from 1991 to 2002 and about 70 percent of the
population lives in poverty. While the government has been in the
process of rebuilding the nation, many forms of Civil Society
Organizations (CSOs), including FBOs, have played a significant role
in promoting social development. Education plays an important role in
supporting people-s democratic movements through knowledge
acquisition, spiritual enlightenment and empowerment. This paper
discusses religious tolerance in Sierra Leone and how FBOs have
contributed to the provision of primary education in Sierra Leone. This
study is based on the author-s field research, which involved
interviews with teachers and development stakeholders, notably
government officials, Non-governmental Organizations (NGOs) and
FBOs, as well as questionnaires completed by pupils, parents and
teachers.
Abstract: A newly designed gas-distributor for granulation of powdery materials in equilibrated fluidized bed and a system for collecting the granules prepared are suggested. The aim of these designs is to solve the problems arising by the granulation of powdery materials in fluidized bed devices. The gasdistributor and the collection system proved to be reliable at operation; they reduce the size of still zones, effectively disperse the binding solution in the bed and ensure the collection of granules of given diameter
Abstract: The fundamental objective of the university is to
genuinely provide a higher education to mankind and society. Higher
education institutions earn billions of dollars in research funds, granted
by national government or related institutions, which literally came
from taxpayers. Everyday universities consume those grants; in return,
provide society with a human resource and research developments.
However, not all taxpayers have their major concerns on those
researches, other than that they are more curiously to see the project
being build tangibly and evidently to certify what they pay for. This
paper introduces the concept of University – Community Business
Continuity Management for Disaster – Resilient City, which modified
the concept of Business Continuity Management (BCM) toward
university community to create advancing collaboration leading to the
disaster – resilient community and city. This paper focuses on
describing in details the backgrounds and principles of the concept and
discussing the advantages and limitations of the concept.
Abstract: Major social changes in the last century had significant impact on the Kazakh literature. Participants of the World War II, writers and poets imprisoned during the war, formed the Kazakh literature in emigration within the framework of 'Turkistan Legion'. This was a topic which remained closed until Kazakhstan gained its independence, though even after the independence, there were few research works done about the literature in emigration. The article studies the formation of the Kazakh literature in emigration, its prominent figures, its artistic heritage, and notes of emigration in works of poets and writers.
Abstract: In ubiqutious healthcare environment, user's health data are transfered to the remote healthcare server by the user's wearable system or mobile phone. These collected user's health data should be managed and analyzed in the healthcare server, so that care giver or user can monitor user's physiological state. In this paper, we designed and developed the intelligent Healthcare Server to manage the user's health data using CDSS and ontology. Our system can analyze user's health data semantically using CDSS and ontology, and report the result of user's physiological raw data to the user and care giver.
Abstract: In this paper are illustrated the principal aspects
connected with the numerical evaluation of thermal stress induced by high gradient temperature in the concrete beam. The reinforced concrete beam has many advantages over steel
beam, such as high resistance to high temperature, high resistance to thermal shock, Better resistance to fatigue and buckling, strong
resistance against, fire, explosion, etc.
The main drawback of the reinforced concrete beam is its poor resistance to tensile stresses. In order to investigate the thermal
induced tensile stresses, a numerical model of a transient thermal
analysis is presented for the evaluation of thermo-mechanical
response of concrete beam to the high temperature, taking into account the temperature dependence of the thermo physical properties of the concrete like thermal conductivity and specific heat.
Abstract: Impinging jets are widely used in industrial cooling
systems for their high heat transfer characteristics at stagnation points.
However, the heat transfer characteristics are low in the downstream
direction. In order to improve the heat transfer coefficient further
downstream, investigations introducing ribs on jet-cooled flat plates
have been conducted. Most studies regarding the heat-transfer
enhancement using a rib-roughened wall have dealt with the rib pitch.
In this paper, we focused on the rib spacing and demonstrated that the
rib spacing must be more than 6 times the nozzle width to improve heat
transfer at Reynolds number Re=5.0×103 because it is necessary to
have enough space to allow reattachment of flow behind the first rib.
Abstract: Many medical devices are driven by motor pumps. Some researchers reported that the vibration mainly affected medical devices using a motor pump. The purpose of this study was to examine the effect of stiffness and damping coefficient in a 3-dimensional (3D) model of a motor pump and spring. In the present paper, experimental and mathematical tests for the moments of inertia of the 3D model and the material properties were investigated by an INSTRON machine. The response surfaces could be generated by using 3D multi-body analysis and the design of experiment method. It showed that differences in contours of the response surface were clearly found for the particular area. Displacement of the center of the motor pump was decreased at K≈2000 N/M, C≈12.5 N-sec/M. However, the frequency was increased at K≈2000 N/M, C≈15 N-sec/M. In this study, this study suggested experimental technique for vibration reduction for a motor pump in medical device. The combined method suggested in this study will greatly contribute to design of medical devices concerning vibration and noise intervention.
Abstract: We proposes a way of removing noises and reducing the number of colors contained in a JPEG image. Main purpose of this project is to convert color images to monochrome images for the color blinds. We treat the crispy color images like the Tokyo subway map. Each color in the image has an important information. But for the color blinds, similar colors cannot be distinguished. If we can convert those colors to different gray values, they can distinguish them.
Abstract: To simulate heating systems in buildings, a research oriented computer code has been developed in Sharif University of Technology in Iran where the climate, existing heating equipment in buildings, consumer behavior and their interactions are considered for simulating energy consumption in conventional systems such as heaters, radiators and fan-coils. In order to validate the computer code, the available data of five buildings was used and the computed consumed energy was compared with the estimated energy extracted from monthly bills. The initial heating system was replaced by the alternative system and the effect of this change was observed on the energy consumption. As a result, the effect of changing heating equipment on energy consumption was investigated in different climates. Changing heater to radiator renders energy conservation up to 50% in all climates and changing radiator to fan-coil decreases energy consumption in climates with cold and dry winter.
Abstract: User interaction components of Augmented Reality (AR) systems have to be tested with users in order to find and fix usability problems as early as possible. In this paper we will report on a user-centered design approach for AR systems following the experience acquired during the design and evaluation of a software prototype for an AR-based educational platform. In this respect we will focus on the re-design of the user task based on the results from a formative usability evaluation. The basic idea of our approach is to describe task scenarios in a tabular format, to develop a task model in a task modeling environment and then to simulate the execution.
Abstract: Prolonged immobilization leads to significant
weakness and atrophy of the skeletal muscle and can also impair the
recovery of muscle strength following injury. Therefore, it is
important to minimize the period under immobilization and accelerate
the return to normal activity. This study examined the effects of heat
treatment and rest-inserted exercise on the muscle activity of the lower
limb during knee flexion/extension. Twelve healthy subjects were
assigned to 4 groups that included: (1) heat treatment + rest-inserted
exercise; (2) heat + continuous exercise; (3) no heat + rest-inserted
exercise; and (4) no heat + continuous exercise. Heat treatment was
applied for 15 mins prior to exercise. Continuous exercise groups
performed knee flexion/extension at 0.5 Hz for 300 cycles without rest
whereas rest-inserted exercise groups performed the same exercise but
with 2 mins rest inserted every 60 cycles of continuous exercise.
Changes in the rectus femoris and hamstring muscle activities were
assessed at 0, 1, and 2 weeks of treatment by measuring the
electromyography signals of isokinetic maximum voluntary
contraction. Significant increases in both the rectus femoris and
hamstring muscles were observed after 2 weeks of treatment only
when both heat treatment and rest-inserted exercise were performed.
These results suggest that combination of various treatment techniques,
such as heat treatment and rest-inserted exercise, may expedite the
recovery of muscle strength following immobilization.
Abstract: A control system design with Characteristic Ratio
Assignment (CRA) is proven that effective for SISO control design.
But the control system design for MIMO via CRA is not concrete
procedure. In this paper presents the control system design method
for quadruple-tank process via CRA. By using the decentralized
method for both minimum phase and non-minimum phase are made.
The results from PI and PID controller design via CRA can be
illustrated the validity of our approach by MATLAB.
Abstract: Recently, the improvements in processing performance
of a computer and in high speed communication of an optical fiber
have been achieved, so that the amount of data which are processed
by a computer and flowed on a network has been increasing greatly.
However, in a client-server system, since the server receives and
processes the amount of data from the clients through the network, a
load on the server is increasing. Thus, there are needed to introduce
a server with high processing ability and to have a line with high
bandwidth. In this paper, concerning to P2P networks to resolve the
load on a specific server, a criterion called an Indexed-Priority Metric
is proposed and its performance is evaluated. The proposed metric is
to allocate some files to each node. As a result, the load on a specific
server can distribute them to each node equally well. A P2P file
sharing system using the proposed metric is implemented. Simulation
results show that the proposed metric can make it distribute files on
the specific server.
Abstract: When programming in languages such as C, Java, etc.,
it is difficult to reconstruct the programmer's ideas only from the
program code. This occurs mainly because, much of the programmer's
ideas behind the implementation are not recorded in the code during
implementation. For example, physical aspects of computation such as
spatial structures, activities, and meaning of variables are not required
as instructions to the computer and are often excluded. This makes the
future reconstruction of the original ideas difficult. AIDA, which is a
multimedia programming language based on the cyberFilm model, can
solve these problems allowing to describe ideas behind programs
using advanced annotation methods as a natural extension to
programming. In this paper, a development environment that
implements the AIDA language is presented with a focus on the
annotation methods. In particular, an actual scientific numerical
computation code is created and the effects of the annotation methods
are analyzed.
Abstract: In the paper we submit the non-local modification of
kinetic Smoluchowski equation for binary aggregation applying to
dispersed media having memory. Our supposition consists in that that
intensity of evolution of clusters is supposed to be a function of the
product of concentrations of the lowest orders clusters at different
moments. The new form of kinetic equation for aggregation is
derived on the base of the transfer kernels approach. This approach
allows considering the influence of relaxation times hierarchy on
kinetics of aggregation process in media with memory.
Abstract: Fatigue tests of specimen-s with numerous holes are
presented. The tests were made up till fatigue cracks have been
created on both sides of the hole. Their extension was stopping with
pressed plastic deformation at the mouth of the detected crack. It is
shown that the moments of occurrence of cracks on holes are
stochastically dependent. This dependence has positive and negative
correlation relations. Shown that the positive correlation is formed
across of the applied force, while negative one – along it. The
negative relationship extends over a greater distance. The
mathematical model of dependence area formation is represented as
well as the estimating of model parameters. The positive correlation
of fatigue cracks origination can be considered as an extension of one
main crack. With negative correlation the first crack locates the place
of its origin, leading to the appearance of multiple cracks; do not
merge with each other.