Abstract: The purpose of this article applies the monthly final
energy yield and failure data of 202 PV systems installed in Taiwan to
analyze the PV operational performance and system availability. This
data is collected by Industrial Technology Research Institute through
manual records. Bad data detection and failure data estimation
approaches are proposed to guarantee the quality of the received
information. The performance ratio value and system availability are
then calculated and compared with those of other countries. It is
indicated that the average performance ratio of Taiwan-s PV systems
is 0.74 and the availability is 95.7%. These results are similar with
those of Germany, Switzerland, Italy and Japan.
Abstract: The world economic crises and budget constraints
have caused authorities, especially those in developing countries, to
rationalize water quality monitoring activities. Rationalization
consists of reducing the number of monitoring sites, the number of
samples, and/or the number of water quality variables measured. The
reduction in water quality variables is usually based on correlation. If
two variables exhibit high correlation, it is an indication that some of
the information produced may be redundant. Consequently, one
variable can be discontinued, and the other continues to be measured.
Later, the ordinary least squares (OLS) regression technique is
employed to reconstitute information about discontinued variable by
using the continuously measured one as an explanatory variable. In
this paper, two record extension techniques are employed to
reconstitute information about discontinued water quality variables,
the OLS and the Line of Organic Correlation (LOC). An empirical
experiment is conducted using water quality records from the Nile
Delta water quality monitoring network in Egypt. The record
extension techniques are compared for their ability to predict
different statistical parameters of the discontinued variables. Results
show that the OLS is better at estimating individual water quality
records. However, results indicate an underestimation of the variance
in the extended records. The LOC technique is superior in preserving
characteristics of the entire distribution and avoids underestimation
of the variance. It is concluded from this study that the OLS can be
used for the substitution of missing values, while LOC is preferable
for inferring statements about the probability distribution.
Abstract: Building intelligent traffic guide systems has been an
interesting subject recently. A good system should be able to observe
all important visual information to be able to analyze the context of
the scene. To do so, signs in general, and traffic signs in particular,
are usually taken into account as they contain rich information to
these systems. Therefore, many researchers have put an effort on
sign recognition field. Sign localization or sign detection is the most
important step in the sign recognition process. This step filters out
non informative area in the scene, and locates candidates in later
steps. In this paper, we apply a new approach in detecting sign
locations using a new color invariant model. Experiments are carried
out with different datasets introduced in other works where authors
claimed the difficulty in detecting signs under unfavorable imaging
conditions. Our method is simple, fast and most importantly it gives
a high detection rate in locating signs.
Abstract: Y chromosome microdeletions are the most common
genetic cause of male infertility and screening for these
microdeletions in azoospermic or severely oligospermic men is now
standard practice. Analysis of the Y chromosome in men with
azoospermia or severe oligozoospermia has resulted in the
identification of three regions in the euchromatic part of the long arm
of the human Y chromosome (Yq11) that are frequently deleted in
men with otherwise unexplained spermatogenic failure. PCR analysis
of microdeletions in the AZFa, AZFb and AZFc regions of the
human Y chromosome is an important screening tool. The aim of this
study was to analyse the type of microdeletions in men with fertility
disorders in Slovakia. We evaluated 227 patients with azoospermia
and with normal karyotype. All patient samples were analyzed
cytogenetically. For PCR amplification of sequence-tagged sites
(STS) of the AZFa, AZFb and AZFc regions of the Y chromosome
was used Devyser AZF set. Fluorescently labeled primers for all
markers in one multiplex PCR reaction were used and for automated
visualization and identification of the STS markers we used genetic
analyzer ABi 3500xl (Life Technologies). We reported 13 cases of
deletions in the AZF region 5,73%. Particular types of deletions were
recorded in each region AZFa,b,c .The presence of microdeletions in
the AZFc region was the most frequent. The study confirmed that
percentage of microdeletions in the AZF region is low in Slovak
azoospermic patients, but important from a prognostic view.
Abstract: The aim of this research was to calculate the thermal
properties of Au3Ni Nanowire. The molecular dynamics (MD)
simulation technique was used to obtain the effect of radius size on
the energy, the melting temperature and the latent heat of fusion at
the isobaric-isothermal (NPT) ensemble. The Quantum Sutton-Chen
(Q-SC) many body interatomic potentials energy have been used for
Gold (Au) and Nickel (Ni) elements and a mixing rule has been
devised to obtain the parameters of these potentials for nanowire
stats. Our MD simulation results show the melting temperature and
latent heat of fusion increase upon increasing diameter of nanowire.
Moreover, the cohesive energy decreased with increasing diameter of
nanowire.
Abstract: Since the conception of JML, many tools, applications and implementations have been done. In this context, the users or developers who want to use JML seem surounded by many of these tools, applications and so on. Looking for a common infrastructure and an independent language to provide a bridge between these tools and JML, we developed an approach to embedded contracts in XML for Java: XJML. This approach offer us the ability to separate preconditions, posconditions and class invariants using JML and XML, so we made a front-end which can process Runtime Assertion Checking, Extended Static Checking and Full Static Program Verification. Besides, the capabilities for this front-end can be extended and easily implemented thanks to XML. We believe that XJML is an easy way to start the building of a Graphic User Interface delivering in this way a friendly and IDE independency to developers community wich want to work with JML.
Abstract: Simplified coupled engine block-crankshaft models
based on beam theory provide an efficient substitute to engine
simulation in the design process. These models require accurate
definition of the main bearing stiffness. In this paper, an investigation
of this stiffness is presented. The clearance effect is studied using a
smooth bearing model. It is manifested for low shaft displacement.
The hydrodynamic assessment model shows that the oil film has no
stiffness for low loads and it is infinitely rigid for important loads.
The deformation stiffness is determined using a suitable finite
elements model based on real CADs. As a result, a main bearing
behaviour law is proposed. This behaviour law takes into account the
clearance, the hydrodynamic sustention and the deformation stiffness.
It ensures properly the transition from the configuration low rigidity
to the configuration high rigidity.
Abstract: The aim of this study was to investigate the effects of
supplementing the diluent of roosters' semen with different levels of
olive oil on motility, viability, morphology and acrosome integrity of
chicken spermatozoa after in vitro storage for up to 72 h. Semen was
collected from 60 White Layer males (62 wk of age) kept in
separated floor pens and randomly divided into six treatment groups
(10 males in each group). Experimental groups were as follows: T1
:fresh semen, T2 : semen extended 1:1 with Al – Daraji 2 diluent
(AD2D) alone, T3 – T6 :semen samples extended 1:1 with AD2D
supplemented with 2 ml, 4 ml, 6 ml or 8 ml of olive oil / 100 ml of
diluent, respectively. Semen samples were then stored at 5 °C for 24
h, 48 h or 72 h. There was a clear influence of diluent
supplementation with olive oil on the spermatozoa motility profile;
olive oil groups (T3, T4, T5 and T6) recorded the highest scores of
mass activity and individual motility during all storage periods
compared to T1 and T2 groups. In addition, the inclusion of olive oil
into semen diluent (T3, T4, T5 and T6) gave significantly higher
percentages of viable spermatozoa, normal morphologically
spermatozoa and intact acrosomes irrespective of storage period.
These results clearly show that supplementation the diluent of
roosters' semen with olive oil can improve semen quality when
semen samples in vitro stored at 5 °C for up to 72 h.
Abstract: One approach to assess neural networks underlying the cognitive processes is to study Electroencephalography (EEG). It is relevant to detect various mental states and characterize the physiological changes that help to discriminate two situations. That is why an EEG (amplitude, synchrony) classification procedure is described, validated. The two situations are "eyes closed" and "eyes opened" in order to study the "alpha blocking response" phenomenon in the occipital area. The good classification rate between the two situations is 92.1 % (SD = 3.5%) The spatial distribution of a part of amplitude features that helps to discriminate the two situations are located in the occipital regions that permit to validate the localization method. Moreover amplitude features in frontal areas, "short distant" synchrony in frontal areas and "long distant" synchrony between frontal and occipital area also help to discriminate between the two situations. This procedure will be used for mental fatigue detection.
Abstract: Considering today-s increasing speed of change,
radical and innovative improvement - Kaikaku, is a necessity parallel
to continuous incremental improvement - Kaizen, especially for
SME-s in order to attain the competitive edge needed to be profitable.
During 2011, a qualitative single case study with the objective of
realizing a kaikaku in production has been conducted. The case study
was run as a one year project using a collaborative approach
including both researchers and company representatives. The case
study was conducted with the purpose of gaining further knowledge
about kaikaku realization as well as its implications. The empirical
results provide insights about the great productivity results achieved
by applying a specific kaikaku realization approach. However, it also
sheds light on the difficulty and contradiction of combining
innovation management and production system development.
Abstract: This paper presents the adaptive control scheme
with sliding mode compensator for vibration control problem
in the presence of disturbance. The dynamic model of the
flexible cantilever beam using finite element modeling is
derived. The adaptive control with sliding mode compensator
using output feedback for output tracking is developed to
reject the external disturbance, and to improve the tracking
performance. Satisfactory simulation results verify that the
effectiveness of adaptive control scheme with sliding mode
compensator.
Abstract: The main objective of this paper is a comparative
investigate in enhancement of damping power system oscillation via
coordinated design of the power system stabilizer (PSS) and static
synchronous series compensator (SSSC) and static synchronous
compensator (STATCOM). The design problem of FACTS-based
stabilizers is formulated as a GA based optimization problem. In this
paper eigenvalue analysis method is used on small signal stability of
single machine infinite bus (SMIB) system installed with SSSC and
STATCOM. The generator is equipped with a PSS. The proposed
stabilizers are tested on a weakly connected power system with
different disturbances and loading conditions. This aim is to enhance
both rotor angle and power system stability. The eigenvalue analysis
and non-linear simulation results are presented to show the effects of
these FACTS-based stabilizers and reveal that SSSC exhibits the best
effectiveness on damping power system oscillation.
Abstract: This paper presents the experimental results of silicone rubber housing material for 24kV lightning arrester under artificial accelerated ageing test based on IEC 61109 specifications. Specimens having inclined and alternated shed made of HTV silicone rubber with ATH content and having leakage distance 625 mm were tested continuously 1000 hrs in artificial salt fog chamber. After 1000 hrs of salt fog ageing test, obviously surface erosion was observed on trunk between the upper large shed and the lower small shed near the energized end. Decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Chemical analysis by ATR-FTIR confirmed the observation results.
Abstract: The main objectif of this paper is to present a tool that
we have developed subject to characterize and modelling indoor radio
channel propagation at millimetric wave. The tool is based on the
ray tracing technique (RTT). As, in realistic environment we cannot
neglect the significant impact of Human Body Shadowing and other
objects in motion on indoor 60 GHz propagation channel. Hence,
our proposed model allows a simulation of propagation in a dynamic
indoor environment. First, we describe a model of human body.
Second, RTT with this model is used to simulate the propagation
of millimeter waves in the presence of persons in motion. Results
of the simulation show that this tool gives results in agreement with
those reported in the literature. Specially, the effects of people motion
on temporal channel properties.
Abstract: In this article, we aim to discuss the formulation of two explicit group iterative finite difference methods for time-dependent two dimensional Burger-s problem on a variable mesh. For the non-linear problems, the discretization leads to a non-linear system whose Jacobian is a tridiagonal matrix. We discuss the Newton-s explicit group iterative methods for a general Burger-s equation. The proposed explicit group methods are derived from the standard point and rotated point Crank-Nicolson finite difference schemes. Their computational complexity analysis is discussed. Numerical results are given to justify the feasibility of these two proposed iterative methods.
Abstract: With respect to the dissipation of energy through
plastic deformation of joints of prefabricated wall units, the paper
points out the principal importance of efficient reinforcement of the
prefabricated system at its joints. The method, quality and amount of
reinforcement are essential for reaching the necessary degree of joint
ductility. The paper presents partial results of experimental research
of vertical joints of prefabricated units exposed to monotonously
rising loading and repetitive shear force and formulates a conclusion
that the limit state of the structure as a whole is preceded by the
disintegration of joints, or that the structure tends to pass from
linearly elastic behaviour to non-linearly elastic to plastic behaviour
by exceeding the proportional elastic limit in joints.Experimental
verification on a model of a 7-storey prefabricated structure revealed
weak points in its load-bearing systems, mainly at places of critical
points around openings situated in close proximity to vertical joints
of mutually perpendicularly oriented walls.
Abstract: An experimental and simulation flight test has been carried out to evaluate the longitudinal gliding characteristics of a lifting body with blunted half-cone geometry. The novelty here is the lifting body's pitch control mechanism, which consists of a pair of leading-edge rotating cylinders. Flight simulation uses aerodynamic data from computational fluid dynamics supported by wind-tunnel test. Flight test consists of releasing an aluminum lifting body model from a moving vehicle at the appropriate wind speed while measuring the lifting body's variation of altitude against time of flight. Results show that leading-edge rotating cylinder is able to give small amounts of improvement to the longitudinal stability and pitch control to the lifting body.
Abstract: The aim of this paper is to propose a mathematical
model to determine invariant sets, set covering, orbits and, in
particular, attractors in the set of tourism variables. Analysis was
carried out based on a pre-designed algorithm and applying our
interpretation of chaos theory developed in the context of General
Systems Theory. This article sets out the causal relationships
associated with tourist flows in order to enable the formulation of
appropriate strategies. Our results can be applied to numerous cases.
For example, in the analysis of tourist flows, these findings can be
used to determine whether the behaviour of certain groups affects that
of other groups and to analyse tourist behaviour in terms of the most
relevant variables. Unlike statistical analyses that merely provide
information on current data, our method uses orbit analysis to
forecast, if attractors are found, the behaviour of tourist variables in
the immediate future.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: High Voltage (HV) transmission lines are widely
spread around residential places. They take all forms of shapes:
concrete, steel, and timber poles. Earth grid always form part of the
HV transmission structure, whereat soil resistivity value is one of the
main inputs when it comes to determining the earth grid
requirements. In this paper, the soil structure and its implication on
the electrode resistance of HV transmission poles will be explored. In
Addition, this paper will present simulation for various soil structures
using IEEE and Australian standards to verify the computation with
CDEGS software. Furthermore, the split factor behavior under
different soil resistivity structure will be presented using CDEGS
simulations.