Abstract: In a competitive energy market, system reliability
should be maintained at all times. Power system operation being of
online in nature, the energy balance requirements must be satisfied to
ensure reliable operation the system. To achieve this, information
regarding the expected status of the system, the scheduled
transactions and the relevant inputs necessary to make either a
transaction contract or a transmission contract operational, have to be
made available in real time. The real time procedure proposed,
facilitates this. This paper proposes a quadratic curve learning
procedure, which enables a generator-s contribution to the retailer
demand, power loss of transaction in a line at the retail end and its
associated losses for an oncoming operating scenario to be predicted.
Matlab program was used to test in on a 24-bus IEE Reliability Test
System, and the results are found to be acceptable.
Abstract: An exploratory computational investigation using
RANS & URANS was carried out to understand the aerodynamics
around an isolatedsingle rotating wheel with decreasing ground
proximity. The wheel was initially modeled in free air conditions,
then with decreasing ground proximity and increased yaw angle with
rotational speeds. Three speeds of rotation were applied to the wheel
so that the effect of different angular velocities can be investigated. In
addition to rotation, three different yaw angles were applied to the
rotating wheel in order to understand how these two variables
combined affect the aerodynamic flow field around the wheel.
Abstract: Post-anthesis drought stress is the most important
problem affecting wheat production in dryland fields, specially in
Mediterranean regions. The main objective of this research was to
evaluate drought tolerance indices in dryland wheat genotypes under
post-anthesis drought stress. The research was including two different
experiments. In each experiment, twenty dryland bread wheat
genotypes were sown in a randomized complete blocks design
(RCBD) with three replications. One of experiments belonged to
rain-fed conditions (post-anthesis drought stress) and other
experiment was under non-stress conditions (with supplemental
irrigation). Different drought tolerance indices include Stress
Tolerance (Tol), Mean Productivity (MP), Geometric Mean
Productivity (GMP), Stress Susceptibility Index (SSI), Stress
Tolerance Index (STI), Harmonic Mean (HAM), Yield Index (YI)
and Yield Stability Index (YSI) were evaluate based on grain yield
under rain-fed (Ys) and supplemental irrigation (Yp) environments.
G10 and G12 were the most tolerant genotypes based on TOL and
SSI. But, based on MP, GMP, STI, HAM and YI indices, G1 and G2
were selected. STI, GMP and MP indices had high correlation with
grain yield under rain-fed and supplementary irrigation conditions
and were recognized as appropriate indices to identify genotypes with
high grain yield and low sensitivity to drought stress environments.
Abstract: For cognitive radio networks, there is a major
spectrum sensing problem, i.e. dynamic spectrum management. It is
an important issue to sense and identify the spectrum holes in
cognitive radio networks. The first-order derivative scheme is usually
used to detect the edge of the spectrum. In this paper, a novel
spectrum sensing technique for cognitive radio is presented. The
proposed algorithm offers efficient edge detection. Then, simulation
results show the performance of the first-order derivative scheme and
the proposed scheme and depict that the proposed scheme obtains
better performance than does the first-order derivative scheme.
Abstract: High Power Lasers produce an intense burst of
Bremmstrahlung radiation which has potential applications in broadband
x-ray radiography. Since the radiation produced is through the
interaction of accelerated electrons with the remaining laser target,
these bursts are extremely short – in the region of a few ps. As a
result, the laser-produced x-rays are capable of imaging complex
dynamic objects with zero motion blur.
Abstract: Raw wood vinegar was purified by both standing and
filtering methods. Toxicity tests were conducted under laboratory
conditions by the topical application method (contact poison) and
feeding method (stomach poison). Larvicidal activities of wood
vinegar at four different concentrations (10, 15, 20, 25 and 30 %)
were studied against second instar larvae of housefly (Musca
domestica L.). Four replicates were maintained for all treatments and
controls. Larval mortality was recorded up to 96 hours and compared
with the larval survivability by two methods of larvicidal bioassay.
Percent pupation and percent adult emergence were observed in
treated M. domestica. The study revealed that the feeding method
gave higher efficiency compared with the topical application method.
Larval mortality increased with increasing concentration of wood
vinegar and the duration of exposure. No mortality was found in
treated M. domestica larvae at minimum 10% concentration of wood
vinegar through the experiments. The treated larvae were maintained
up to pupa and adult emergence. At 30% maximum concentration
larval duration was extended to 11 days in M. domestica for topical
application method and 9 days for feeding method. Similarly the
pupal durations were also increased with increased concentrations
(16 and 24 days for topical application method and feeding method
respectively at 30% concentration) of the treatments.
Abstract: Optimal routing in communication networks is a
major issue to be solved. In this paper, the application of Tabu Search
(TS) in the optimum routing problem where the aim is to minimize
the computational time and improvement of quality of the solution in
the communication have been addressed. The goal is to minimize the
average delays in the communication. The effectiveness of Tabu
Search method is shown by the results of simulation to solve the
shortest path problem. Through this approach computational cost can
be reduced.
Abstract: This paper presents the climatic range calculations for
comfort evaporative cooling for Tehran. In this study the minimum
climatic conditions required to achieve an appropriate comfort zone
will be presented.
Physiologically uncomfortable conditions in arid climates are
mainly caused by the extreme heat and dryness. Direct evaporative
cooling adds moisture to the air stream until the air stream is close to
saturation. The dry bulb temperature is reduced, while the wet bulb
temperature stays the same. Evaporative cooling is economical,
effective, environmentally friendly, and healthy.
Comfort cooling by direct evaporative cooling (passive or fan
forced) in the 35. 41 N (such as Tehran) latitude requires design
wet-bulb temperature not over 25.4 C. Evaporative cooling outside
this limit cannot achieve the required 26.7 ET, and is recommended
for relief cooling only.
Abstract: This paper presents the impact study of apparent
reactance injected by series Flexible AC Transmission System
(FACTS) i.e. Thyristor Controlled Series Reactor (TCSR) on the
measured impedance of a 400 kV single electrical transmission line
in the presence of phase to earth fault with fault resistance. The study
deals with an electrical transmission line of Eastern Algerian
transmission networks at Group Sonelgaz (Algerian Company of
Electrical and Gas) compensated by TCSR connected at midpoint of
the line. This compensator used to inject active and reactive powers
is controlled by three TCSR-s. The simulations results investigate the
impacts of the TCSR on the parameters of short circuit calculation
and parameters of measured impedance by distance relay in the
presence of earth fault for three cases study.
Abstract: Active research is underway on virtual touch screens
that complement the physical limitations of conventional touch
screens. This paper discusses a virtual touch screen that uses a
multi-layer perceptron to recognize and control three-dimensional
(3D) depth information from a time of flight (TOF) camera. This
system extracts an object-s area from the image input and compares it
with the trajectory of the object, which is learned in advance, to
recognize gestures. The system enables the maneuvering of content in
virtual space by utilizing human actions.
Abstract: This study proposes novel hybrid social network analysis and collaborative filtering approach to enhance the performance of recommender systems. The proposed model selects subgroups of users in Internet community through social network analysis (SNA), and then performs clustering analysis using the information about subgroups. Finally, it makes recommendations using cluster-indexing CF based on the clustering results. This study tries to use the cores in subgroups as an initial seed for a conventional clustering algorithm. This model chooses five cores which have the highest value of degree centrality from SNA, and then performs clustering analysis by using the cores as initial centroids (cluster centers). Then, the model amplifies the impact of friends in social network in the process of cluster-indexing CF.
Abstract: Incremental forming is a complex forming process with
continuously local cumulative deformation taking place during its
process, and springback that forming quality affected by would occur.
The springback evaluation method based on forming error
compensation also was proposed, which it can be defined as the
difference between theory and the actual amount of compensation
along the measured direction. According to forming error
compensation evaluation method, experiments was designed and
implemented. And from the results that obtained it can be show, the
magnitude of springback average (δE) of formed parts was very small,
and the forming precision could be significantly improved by adopting
compensation method. Based on double tensile stress state in the main
deformation area, a hypothesis that there is little springback be arisen
by bending behavior on the formed parts that was proposed.
Abstract: Operating rooms are important assets for hospitals as
they generate the largest revenue and, at the same time, produce the
largest cost for hospitals. The model presented in this paper helps
make capacity planning decisions on the combination of open
operating rooms (ORs) and estimated overtime to satisfy the
allocated OR time to each specialty. The model combines both
decisions on determining the amount of OR time to open and to
allocate to different surgical specialties. The decisions made are
based on OR costs, overutilization and underutilization costs, and
contribution margins from allocating OR time. The results show the
importance of having a good estimate of specialty usage of OR time
to determine the amount of needed capacity and highlighted the
tradeoff that the OR manager faces between opening more ORs
versus extending the working time of the ORs already in use.
Abstract: This study aimed to develop and initially validate an instrument that measures social competency among tertiary level faculty members. A review of extant literature on social competence was done. The review of extant literature led to the writing of the items in the initial instrument which was evaluated by 11 Subject Matter Experts (SMEs). The SMEs were either educators or psychologists. The results of the evaluations done by the SMEs served as bases for the creation of the pre-try-out instrument used in the first trial-run. Insights from the first trial-run participants led to the development of the main try-out instrument used in the final test administration. One Hundred Forty-one participants from five private Higher Education Institutions (HEIs) in the National Capital Region (NCR) and five private HEIs in Central Luzon in the Philippines participated in the final test administration. The reliability of the instrument was evaluated using Cronbach-s Coefficient Alpha formula and had a Cronbach-s Alpha of 0.92. On the other hand, Factor Analysis was used to evaluate the validity of the instrument and six factors were identified. The development of the final instrument was based on the results of the evaluation of the instrument-s reliability and validity. For purposes of recognition, the instrument was named “Social Competency Inventory for Tertiary Level Faculty Members (SCI-TLFM)."
Abstract: Polymeric microreactors have emerged as a new
generation of carriers that hold tremendous promise in the areas of
cancer therapy, controlled delivery of drugs, for removal of
pollutants etc. Present work reports a simple and convenient
methodology for synthesis of polystyrene and poly caprolactone
microreactors. An aqueous suspension of carboxylated (1μm)
polystyrene latex particles was mixed with toluene solution followed
by freezing with liquid nitrogen. Freezed particles were incubated at
-20°C and characterized for formation of voids on the surface of
polymer microspheres by Field Emission Scanning Electron
Microscope. The hollow particles were then overnight incubated at
40ºC with unfunctionalized quantum dots (QDs) in 5:1 ratio. QDs
Encapsulated polystyrene microcapsules were characterized by
fluorescence microscopy.
Likewise Poly ε-caprolactone microreactors were prepared by
micro-volcanic rupture of freeze dried microspheres synthesized
using emulsification of polymer with aqueous Poly vinyl alcohol and
freezed with liquid nitrogen. Microreactors were examined with Field
Emission Scanning Electron Microscope for size and morphology.
Current study is an attempt to create hollow polymer particles which
can be employed for microencapsulation of nanoparticles and drug
molecules.
Abstract: This paper mainly proposes an efficient modified
particle swarm optimization (MPSO) method, to identify a slidercrank
mechanism driven by a field-oriented PM synchronous motor.
In system identification, we adopt the MPSO method to find
parameters of the slider-crank mechanism. This new algorithm is
added with “distance" term in the traditional PSO-s fitness function to
avoid converging to a local optimum. It is found that the comparisons
of numerical simulations and experimental results prove that the
MPSO identification method for the slider-crank mechanism is
feasible.
Abstract: To achieve reliable solutions, today-s numerical and
experimental activities need developing more accurate methods and
utilizing expensive facilities, respectfully in microchannels. The analytical
study can be considered as an alternative approach to alleviate
the preceding difficulties. Among the analytical solutions, those with
high robustness and low complexities are certainly more attractive.
The perturbation theory has been used by many researchers to analyze
microflows. In present work, a compressible microflow with constant
heat flux boundary condition is analyzed. The flow is assumed to be
fully developed and steady. The Mach and Reynolds numbers are also
assumed to be very small. For this case, the creeping phenomenon
may have some effect on the velocity profile. To achieve robustness
solution it is assumed that the flow is quasi-isothermal. In this study,
the creeping term which appears in the slip boundary condition
is formulated by different mathematical formulas. The difference
between this work and the previous ones is that the creeping term
is taken into account and presented in non-dimensionalized form.
The results obtained from perturbation theory are presented based
on four non-dimensionalized parameters including the Reynolds,
Mach, Prandtl and Brinkman numbers. The axial velocity, normal
velocity and pressure profiles are obtained. Solutions for velocities
and pressure for two cases with different Br numbers are compared
with each other and the results show that the effect of creeping
phenomenon on the velocity profile becomes more important when
Br number is less than O(ε).
Abstract: A Finite Volume method based on Characteristic Fluxes for compressible fluids is developed. An explicit cell-centered resolution is adopted, where second and third order accuracy is provided by using two different MUSCL schemes with Minmod, Sweby or Superbee limiters for the hyperbolic part. Few different times integrator is used and be describe in this paper. Resolution is performed on a generic unstructured Cartesian grid, where solid boundaries are handled by a Cut-Cell method. Interfaces are explicitely advected in a non-diffusive way, ensuring local mass conservation. An improved cell cutting has been developed to handle boundaries of arbitrary geometrical complexity. Instead of using a polygon clipping algorithm, we use the Voxel traversal algorithm coupled with a local floodfill scanline to intersect 2D or 3D boundary surface meshes with the fixed Cartesian grid. Small cells stability problem near the boundaries is solved using a fully conservative merging method. Inflow and outflow conditions are also implemented in the model. The solver is validated on 2D academic test cases, such as the flow past a cylinder. The latter test cases are performed both in the frame of the body and in a fixed frame where the body is moving across the mesh. Adaptive Cartesian grid is provided by Paramesh without complex geometries for the moment.
Abstract: ZnO+Ga2O3 functionally graded thin films (FGTFs)
were examined for their potential use as Solar cell and organic light
emitting diodes (OLEDs). FGTF transparent conducting oxides (TCO)
were fabricated by combinatorial RF magnetron sputtering. The
composition gradient was controlled up to 10% by changing the
plasma power of the two sputter guns. A Ga2O3+ZnO graded region
was placed on the top layer of ZnO. The FGTFs showed up to 80%
transmittance. Their surface resistances were reduced to < 10% by
increasing the Ga2O3: pure ZnO ratio in the TCO. The FGTFs- work
functions could be controlled within a range of 0.18 eV. The
controlled work function is a very promising technology because it
reduces the contact resistance between the anode and Hall transport
layers of OLED and solar cell devices.
Abstract: In this study, single nozzle method used for
electrospinning technique which composite polymer solution with
cellulose nanowiskers (CNW) was treated by ultrasonic sonificator
have been compared with coaxial (double) nozzle method, in terms of
mechanical, thermal and morphological properties of composite
nanofiber. The effect of water content in composite polymer solution
on properties of nanofiber has also been examined. It has been seen
that single nozzle method which polymer solution does not contain
water has better results than that of coaxial method, in terms of
mechanical, thermal and morphological properties of nanofiber.
However, it is necessary to make an optimization study on setting
condition of ultrasonic treatment to get better dispersion of CNW in
composite nanofiber and to get better mechanical and thermal
properties