Abstract: An accurate procedure to determine free vibrations of
beams and plates is presented.
The natural frequencies are exact solutions of governing vibration
equations witch load to a nonlinear homogeny system.
The bilinear and linear structures considered simulate a bridge.
The dynamic behavior of this one is analyzed by using the theory of
the orthotropic plate simply supported on two sides and free on the
two others. The plate can be excited by a convoy of constant or
harmonic loads. The determination of the dynamic response of the
structures considered requires knowledge of the free frequencies and
the shape modes of vibrations. Our work is in this context. Indeed,
we are interested to develop a self-consistent calculation of the Eigen
frequencies.
The formulation is based on the determination of the solution of
the differential equations of vibrations. The boundary conditions
corresponding to the shape modes permit to lead to a homogeneous
system. Determination of the noncommonplace solutions of this
system led to a nonlinear problem in Eigen frequencies.
We thus, develop a computer code for the determination of the
eigenvalues. It is based on a method of bisection with interpolation
whose precision reaches 10 -12. Moreover, to determine the
corresponding modes, the calculation algorithm that we develop uses
the method of Gauss with a partial optimization of the "pivots"
combined with an inverse power procedure. The Eigen frequencies
of a plate simply supported along two opposite sides while
considering the two other free sides are thus analyzed. The results
could be generalized with the case of a beam by regarding it as a
plate with low width.
We give, in this paper, some examples of treated cases. The
comparison with results presented in the literature is completely
satisfactory.
Abstract: Since atmosphere pressure field is an actual envoy of
climatic signal the atmospheric Highs and Lows should be attributed
to the key active focal points within the ocean-atmosphere interplay
system. Here we were set a task to determine how the dynamics of
those centres of action relates to the climate change both on regional
and global scales. For this target the near-surface temperature and
atmospheric pressure differences between the Icelandic Low and the
Azores High were considered. The secular term of phase states of the
system under consideration was found divided into three
nonintersecting subsets. Each of that was put in consequence with
one of three climatic scenarios related to the periods of 1905-1935
(relatively warm phase), 1940-1970 (cold phase) and 1980-2000
(warm phase).
Abstract: In this paper, a new method is proposed to find the fuzzy optimal solution of fuzzy assignment problems by representing all the parameters as triangular fuzzy numbers. The advantages of the pro-posed method are also discussed. To illustrate the proposed method a fuzzy assignment problem is solved by using the proposed method and the obtained results are discussed. The proposed method is easy to understand and to apply for finding the fuzzy optimal solution of fuzzy assignment problems occurring in real life situations.
Abstract: We propose photo-BJMOSFET (Bipolar Junction Metal-Oxide-Semiconductor Field Effect Transistor) fabricated on SOI film. ITO film is adopted in the device as gate electrode to reduce light absorption. I-V characteristics of photo-BJMOSFET obtained in dark (dark current) and under 570nm illumination (photo current) are studied furthermore to achieve high photo-to-dark-current contrast ratio. Two variables in the calculation were the channel length and the thickness of the film which were set equal to six different values, i.e., L=2, 4, 6, 8, 10, and 12μm and three different values, i.e., dsi =100, 200 and 300nm, respectively. The results indicate that the greatest photo-to-dark-current contrast ratio is achieved with L=10μm and dsi=200 nm at VGK=0.6V.
Abstract: Content-Based Image Retrieval has been a major area
of research in recent years. Efficient image retrieval with high
precision would require an approach which combines usage of both
the color and texture features of the image. In this paper we propose
a method for enhancing the capabilities of texture based feature
extraction and further demonstrate the use of these enhanced texture
features in Texture-Based Color Image Retrieval.
Abstract: Four phenylurea herbicides (isoproturon, chlortoluron, diuron and linuron) were dissolved in different water matrices in order to study their chemical degradation by using UV radiation, ozone and some advanced oxidation processes (UV/H2O2, O3/H2O2, Fenton reagent and the photo- Fenton system). The waters used were: ultra-pure water, a commercial mineral water, a groundwater and a surface water taken from a reservoir. Elimination levels were established for each herbicide and for several global quality parameters, and a kinetic study was performed in order to determine basic kinetic parameters of each reaction between the target phenylureas and these oxidizing systems.
Abstract: A major goal of any enterprise is to create a ratings
system of customer satisfaction, goods and services. It is obvious that
the company cannot change what is not measured. In order to get a
clearer picture of the preferences of the major consumer groups, this
stage should be based on extensive research, including a variety of
interviews and surveys. It is necessary to know the key benefits,
which determine customer satisfaction in the market segment, of the
properties of certain goods and services. It is important to estimate
the terms of these preferences from the viewpoint of the client. This
article discusses the importance of customer satisfaction, and ways of
assessing it.
Abstract: An ordered porous antimony-doped tin oxide (ATO) film was successfully prepared using a simple coating process with colloidal templates. The facile production was effective when a combination of 16-nm ATO (as a model of an inorganic nanoparticle) and polystyrene (PS) spheres (as a model of the template) weresimply coated to produce a composite ATO/PS film. Heat treatment was then used to remove the PS and produce the porous film. The porous film with a spherical pore shape and a highly ordered porous structure could be obtained. A potential way for the control of pore size could be also achieved by changing initial template size. The theoretical explanation and mechanism of porous formation were also added, which would be important for the scaling-up prediction and estimation.
Abstract: Nowadays there are many methods for representing
knowledge such as semantic network, neural network, and conceptual
graphs. Nonetheless, these methods are not sufficiently efficient
when applied to perform and deduce on knowledge domains about
supporting in general education such as algebra, analysis or plane
geometry. This leads to the introduction of computational network
which is a useful tool for representation knowledge base, especially
for computational knowledge, especially knowledge domain about
general education. However, when dealing with a practical problem,
we often do not immediately find a new solution, but we search
related problems which have been solved before and then proposing
an appropriate solution for the problem. Besides that, when finding
related problems, we have to determine whether the result of them
can be used to solve the practical problem or not. In this paper, the
extension model of computational network has been presented. In this
model, Sample Problems, which are related problems, will be used
like the experience of human about practical problem, simulate the
way of human thinking, and give the good solution for the practical
problem faster and more effectively. This extension model is applied
to construct an automatic system for solving algebraic problems in
middle school.
Abstract: The compatibility of optical resonators with microfluidic systems may be relevant for chemical and biological applications. Here, a fluorescent-core microcavity (FCM) is investigated as a refractometric sensor for heavy oils. A high-index film of silicon quantum dots (QDs) was formed inside the capillary, supporting cylindrical fluorescence whispering gallery modes (WGMs). A set of standard refractive index oils was injected into a capillary, causing a shift of the WGM resonances toward longer wavelengths. A maximum sensitivity of 240 nm/RIU (refractive index unit) was found for a nominal oil index of 1.74. As well, a sensitivity of 22 nm/RIU was obtained for a lower index of 1.48, more typical of fuel hydrocarbons. Furthermore, the observed spectra and sensitivities were compared to theoretical predictions and reproduced via FDTD simulations, showing in general an excellent agreement. This work demonstrates the potential use of FCMs for oil sensing applications and the more generally for detecting liquid solutions with a high refractive index or high viscosity.
Abstract: New regulations and standards for noise emission increasingly compel the automotive firms to make some improvements about decreasing the engine noise. Nowadays, the perforated reactive mufflers which have an effective damping capability are specifically used for this purpose. New designs should be analyzed with respect to both acoustics and back pressure. In this study, a reactive perforated muffler is investigated numerically and experimentally. For an acoustical analysis, the transmission loss which is independent of sound source of the present cross flow, the perforated muffler was analyzed by COMSOL. To be able to validate the numerical results, transmission loss was measured experimentally. Back pressure was obtained based on the flow field analysis and was also compared with experimental results. Numerical results have an approximate error of 20% compared to experimental results.
Abstract: The State of Rio de Janeiro, Brazil, will hold two important events in the nearby future. In 2014 it will have the final game of the Football World Cup, and in 2016 it will be holding the Olympic Games. Therefore, the public transportation system (mainly buses) is of a major concern to the Rio de Janeiro State authorities-. The main objective of this work is to compare the quality of service of the bus companies operating in the cities of ItaperunaandCampos, both cities situated in the state of Rio de Janeiro, Brazil. The outcome of thiscomparison, based on the opinion of the bus users, has shownthemdispleased with the quality of the service provided by the bus companies operating in both cities. It is urgent the need to find possible practical alternatives to minimize the consequences of the main problems detected in this work. With these practical alternatives available, we will be able to offer to the Rio de Janeiro State authorities- suggestions about possible solutions to the main problems identified in this survey, as well as the time of implantation and costs of these solutions.
Abstract: Principally, plants grown in soilless culture may be
attacked by the same pests and diseases as cultivated traditionally in
soil. The most destructive phytopathogens are fungi, such as
Phythium, Phytophthora and Fusarium, followed by viruses, bacteria
and nematodes. We investigated effect of carbon nanotube filters on
disease management of soilless culture. Tomato seedlings transplant
in plastic pots filled with a soilless media of vermiculite. The crop
irrigated and fertilized using a hydroponic nutrient solution. We used
carbon nanotube filters for nutrient solution disinfection. Our results
show that carbon nanotube filtration significantly reduces pathogens
on tomato plants. Fungal elimination (Fusarium oxysporum and
Pythium spp.) was usually successful at about 96 to 99.9% all over
the cultural season. It is seem that in tomato soilless culture,
nanofiltration constitutes a reliable method that allows control of the
development of diseases caused by pathogenic fungi
Abstract: Two Amphiphilic catalysts, iron (III) dodecylbenzene
sulfonate and nickel (II) dodecylbenzene sulfonate, were synthesized
and used in the catalytic aquathermolysis of heavy crude oil to reduce
its viscosity. The prepared catalysts exhibited good performance in
the aquathermolysis and the viscosity is reduced by ~ 78.9 % for
Egyptian heavy crude oil. The chemical and physical properties of
heavy oil both before and after reaction were investigated by FT-IR,
dynamic viscosity, molecular weight and SARA analysis. The results
indicated that the content of resin, asphaltene, average molecular
weight and sulfur content of heavy oil is reduced after the catalytic
aquathermolysis.
Abstract: This paper describes a novel approach for deriving
modules from protein-protein interaction networks, which combines
functional information with topological properties of the network.
This approach is based on weighted clustering coefficient, which
uses weights representing the functional similarities between the
proteins. These weights are calculated according to the semantic
similarity between the proteins, which is based on their Gene
Ontology terms. We recently proposed an algorithm for identification
of functional modules, called SWEMODE (Semantic WEights for
MODule Elucidation), that identifies dense sub-graphs containing
functionally similar proteins. The rational underlying this approach is
that each module can be reduced to a set of triangles (protein triplets
connected to each other). Here, we propose considering semantic
similarity weights of all triangle-forming edges between proteins. We
also apply varying semantic similarity thresholds between
neighbours of each node that are not neighbours to each other (and
hereby do not form a triangle), to derive new potential triangles to
include in module-defining procedure. The results show an
improvement of pure topological approach, in terms of number of
predicted modules that match known complexes.
Abstract: The significance of emissions from the road transport
sector (such as air pollution, noise, etc) has grown considerably in
recent years. In Australia, 14.3% of national greenhouse gas
emissions in 2000 were the transport sector-s share which 12.9% of
net national emissions were related to a road transport alone.
Considering the growing attention to the green house gas(GHG)
emissions, this paper attempts to provide air pollution modeling
aspects of environmental consequences of the road transport by using
one of the best computer based tools including the Geographic
Information System (GIS). In other word, in this study, GIS and its
applications is explained, models which are used to model air
pollution and GHG emissions from vehicles are described and GIS is
applied in real case study that attempts to forecast GHG emission
from people who travel to work by car in 2031 in Melbourne for
analysing results as thematic maps.
Abstract: Time interleaved sigma-delta (TIΣΔ) architecture is a
potential candidate for high bandwidth analog to digital converters
(ADC) which remains a bottleneck for software and cognitive radio
receivers. However, the performance of the TIΣΔ architecture is
limited by the unavoidable gain and offset mismatches resulting
from the manufacturing process. This paper presents a novel digital
calibration method to compensate the gain and offset mismatch
effect. The proposed method takes advantage of the reconstruction
digital signal processing on each channel and requires only few logic
components for implementation. The run time calibration is estimated
to 10 and 15 clock cycles for offset cancellation and gain mismatch
calibration respectively.
Abstract: In this paper, the innovative intelligent fuzzy weighted
input estimation method (FWIEM) can be applied to the inverse heat
transfer conduction problem (IHCP) to estimate the unknown
time-varying heat flux efficiently as presented. The feasibility of this
method can be verified by adopting the temperature measurement
experiment. We would like to focus attention on the heat flux
estimation to three kinds of samples (Copper, Iron and Steel/AISI 304)
with the same 3mm thickness. The temperature measurements are then
regarded as the inputs into the FWIEM to estimate the heat flux. The
experiment results show that the proposed algorithm can estimate the
unknown time-varying heat flux on-line.
Abstract: In this study four Holstein steers with rumen fistula
fed 7 kg of dry matter (DM) of diets differing in concentrate to
alfalfa hay ratios as 60:40, 70:30, 80:20, and 90:10 in a 4 × 4 latin
square design. The pH of the ruminal fluid was measured before
the morning feeding (0.0 h) to 8 h post feeding. In this study, a
two-layered feed-forward neural network trained by the
Levenberg-Marquardt algorithm was used for modelling of ruminal
pH. The input variables of the network were time, concentrate to
alfalfa hay ratios (C/F), non fiber carbohydrate (NFC) and neutral
detergent fiber (NDF). The output variable was the ruminal pH.
The modeling results showed that there was excellent agreement
between the experimental data and predicted values, with a high
determination coefficient (R2 >0.96). Therefore, we suggest using
these model-derived biological values to summarize continuously
recorded pH data.
Abstract: This study aimed to investigate the influence of selected antecedents, which were tourists’ satisfaction towards attractions in Bangkok, perceived value of the attractions, feelings of engagement with the attractions, acquaintance with the attractions, push factors, pull factors and motivation to seek novelty, on foreign tourist’s loyalty towards tourist attractions in Bangkok. By using multi stage sampling technique, 400 international tourists were sampled. After that, Semi Structural Equation Model was utilized in the analysis stage by LISREL. The Semi Structural Equation Model of the selected antecedents of tourist’s loyalty attractions had a correlation with the empirical data through the following statistical descriptions: Chi- square = 3.43, df = 4, P- value = 0.48893; RMSEA = 0.000; CFI = 1.00; CN = 1539.75; RMR = 0.0022; GFI = 1.00 and AGFI = 0.98. The findings indicated that all antecedents were able together to predict the loyalty of the foreign tourists who visited Bangkok at 73 percent.