Abstract: A major part of the flow field involves no complicated
turbulent behavior in many turbulent flows. In this research work, in
order to reduce required memory and CPU time, the flow field was
decomposed into several blocks, each block including its special
turbulence. A two dimensional backward facing step was considered
here. Four combinations of the Prandtl mixing length and standard k-
E models were implemented as well. Computer memory and CPU
time consumption in addition to numerical convergence and accuracy
of the obtained results were mainly investigated. Observations
showed that, a suitable combination of turbulence models in different
blocks led to the results with the same accuracy as the high order
turbulence model for all of the blocks, in addition to the reductions in
memory and CPU time consumption.
Abstract: The present study attempted to improve the Mercury
(Hg) sorption capacity of kanuma volcanic ash soil (KVAS) by
impregnating the cupper (Cu). Impregnation was executed by 1 and
5% Cu powder and sorption characterization of optimum Hg
removing Cu impregnated KVAS was performed under different
operational conditions, contact time, solution pH, sorbent dosage and
Hg concentration using the batch operation studies. The 1% Cu
impregnated KVAS pronounced optimum improvement (79%) in
removing Hg from water compare to control. The present
investigation determined the equilibrium state of maximum Hg
adsorption at 6 h contact period. The adsorption revealed a pH
dependent response and pH 3.5 showed maximum sorption capacity
of Hg. Freundlich isotherm model is well fitted with the experimental
data than that of Langmuir isotherm. It can be concluded that the Cu
impregnation improves the Hg sorption capacity of KVAS and 1%
Cu impregnated KVAS could be employed as cost-effective
adsorbent media for treating Hg contaminated water.
Abstract: Organochlorine pesticides (OCPs) are known to be
persistent and bioaccumulative toxicants that may cause reproductive
impairments in wildlife as well as human. The current study uses the
snail-eating turtle Malayemys macrocephala, a long-lived animal
commonly distribute in rice field habitat in central part of Thailand,
as a sentinel to monitor OCP contamination in environment. The
nest soil, complete clutch of eggs, and blood of the turtle were
collected from agricultural areas in the Chao Phraya River Basin,
Thailand during the nesting season of 2007-2008. The novel
methods for tissue extraction by an accelerated solvent extractor
(ASE, for egg) and liquid-liquid extraction (for blood) have been
developed. The nineteen OCP residues were analyzed by gas
chromatography with micro-electron captured detector (GC-μECD).
The validated methods have met requirements of the AOAC
standard. The results indicated that significant amounts of OCPs are
still contaminated in nest soil and eggs of the turtle even though the
OCPs had been banned in this area for many years. This suggested
the potential risk to health of wildlife as well as human in the area.
Abstract: This paper presents a new approach for the prob-ability density function estimation using the Support Vector Ma-chines (SVM) and the Expectation Maximization (EM) algorithms.In the proposed approach, an advanced algorithm for the SVM den-sity estimation which incorporates the Mean Field theory in the learning process is used. Instead of using ad-hoc values for the para-meters of the kernel function which is used by the SVM algorithm,the proposed approach uses the EM algorithm for an automatic optimization of the kernel. Experimental evaluation using simulated data set shows encouraging results.
Abstract: A pilot project was carried out in 2007 by the senior
students of Cyprus International University, aiming to minimize the
total cost of waste collection in Northern Cyprus. Many developed
and developing countries have cut their transportation costs – which
lies between 30-40% – down at a rate of 40% percent, by
implementing network models for their route assignments.
Accordingly, a network model was implemented at Göçmenköy
district, to optimize and standardize waste collection works. The
work environment of the employees were also redesigned to provide
maximum ergonomy and to increase productivity, efficiency and
safety. Following the collection of the required data including waste
densities, lengths of roads and population, a model was constructed
to allocate the optimal route assignment for the waste collection
trucks at Göçmenköy district.
Abstract: In this paper a novel high output impedance, low input impedance, wide bandwidth, very simple current mirror with input and output voltage requirements less than that of a simple current mirror is presented. These features are achieved with very simple structure avoiding extra large node impedances to ensure high bandwidth operation. The circuit's principle of operation is discussed and compared to simple and low voltage cascode (LVC) current mirrors. Such outstanding features of this current mirror as high output impedance ~384K, low input impedance~6.4, wide bandwidth~178MHz, low input voltage ~ 362mV, low output voltage ~ 38mV and low current transfer error ~4% (all at 50μA) makes it an outstanding choice for high performance applications. Simulation results in BSIM 0.35μm CMOS technology with HSPICE are given in comparison with simple, and LVC current mirrors to verify and validate the performance of the proposed current mirror.
Abstract: The problem of delay-range-dependent exponential synchronization is investigated for Lur-e master-slave systems with delay feedback control and Markovian switching. Using Lyapunov- Krasovskii functional and nonsingular M-matrix method, novel delayrange- dependent exponential synchronization in mean square criterions are established. The systems discussed in this paper is advanced system, and takes all the features of interval systems, Itˆo equations, Markovian switching, time-varying delay, as well as the environmental noise, into account. Finally, an example is given to show the validity of the main result.
Abstract: The fractal-shaped orifices are assumed to have a
significant effect on the pressure drop downstream pipe flow due to
their edge self-similarity shape which enhances the mixing
properties. Here, we investigate the pressure drop after these fractals
using a digital micro-manometer at different stations downstream a
turbulent flow pipe then a direct comparison has been made with the
pressure drop measured from regular orifices with the same flow
area. Our results showed that the fractal-shaped orifices have a
significant effect on the pressure drop downstream the flow. Also
the pressure drop measured across the fractal-shaped orifices is
noticed to be lower that that from ordinary orifices of the same flow
areas. This result could be important in designing piping systems
from point of view of losses consideration with the same flow
control area. This is promising to use the fractal-shaped orifices as
flowmeters as they can sense the pressure drop across them
accurately with minimum losses than the regular ones.
Abstract: The rotation of starting pitchers is a strategic issue
which has a significant impact on the performance of a professional
team. Choosing an optimal starting pitcher from among many
alternatives is a multi-criteria decision-making (MCDM) problem. In
this study, a model using the Analytic Hierarchy Process (AHP) and
Technique for Order Performance by Similarity to the Ideal Solution
(TOPSIS) is proposed with which to arrange the starting pitcher
rotation for teams of the Chinese Professional Baseball League. The
AHP is used to analyze the structure of the starting pitcher selection
problem and to determine the weights of the criteria, while the
TOPSIS method is used to make the final ranking. An empirical
analysis is conducted to illustrate the utilization of the model for the
starting pitcher rotation problem. The results demonstrate the
effectiveness and feasibility of the proposed model.
Abstract: This study was aimed for investigating of
manufacturing high aluminum content Mg alloys using a horizontal
twin roll caster. Recently, weight saving has been key issues for lighter
transport equipments as well as electronic component parts. As
alternative materials to aluminum alloys, developing magnesium alloy
with higher strength has been expected. Normally high Aluminum
content Mg alloy has poor ductility and is difficult to be rolled because
of its high strength. However, twin roll casting process is suitable for
manufacturing wrought Mg alloys because materials can be cast
directly from molten metal. In this study, manufacturing of high
aluminum content magnesium alloy sheet using the roll casting
process has been carried out. Effects of manufacturing parameter, such
as roll velocity, pouring temperature and roll gap, on casting was
investigated. A microscopic observation of the crystals of cross section
of as cast strip as well as rolled strip was conducted.
Abstract: As an effort to promote wind power industry in Korea,
Korea South-East Power Corporation has been developing 22MW
YeungHeung wind farm consisting of nine 2 to 3MW wind turbines
supplied by three manufacturers. To maximize its availability and
reliability and to solve the difficulty of operating three kinds of
SCADA systems, Korea Electric Power Corporation has been
developing a condition monitoring system integrated with control
functions. This paper presents the developed condition monitoring
system and its application to YeungHeung wind test bed, and the
design of its control functions.
Abstract: Data warehousing success is not high enough. User
dissatisfaction and failure to adhere to time frames and budgets are
too common. Most traditional information systems practices are
rooted in hard systems thinking. Today, the great systems thinkers
are forgotten by information systems developers. A data warehouse
is still a system and it is worth investigating whether systems
thinkers such as Churchman can enhance our practices today. This
paper investigates data warehouse development practices from a
systems thinking perspective. An empirical investigation is done in
order to understand the everyday practices of data warehousing
professionals from a systems perspective. The paper presents a
model for the application of Churchman-s systems approach in data
warehouse development.
Abstract: Dynamic location referencing method is an important technology to shield map differences. These method references objects of the road network by utilizing condensed selection of its real-world geographic properties stored in a digital map database, which overcomes the defections existing in pre-coded location referencing methods. The high attributes completeness requirements and complicated reference point selection algorithm are the main problems of recent researches. Therefore, a dynamic location referencing algorithm combining intersection points selected at the extremities compulsively and road link points selected according to link partition principle was proposed. An experimental system based on this theory was implemented. The tests using Beijing digital map database showed satisfied results and thus verified the feasibility and practicability of this method.
Abstract: This paper presents a research agenda on the SCOR
model adaptation. SCOR model is designated to measure supply
chain performance and logistics impact across the boundaries of
individual organizations. It is at its growing stage of its life cycle and
is enjoying the leverage of becoming the industry standard. The
SCOR model has been developed and used widely in developed
countries context. This research focuses on the SCOR model
adaptation for the manufacturing industry in developing countries.
With a necessary understanding of the characteristics, difficulties and
problems of the manufacturing industry in developing countries-
supply chain; consequently, we will try to designs an adapted model
with its building blocks: business process model, performance
measures and best practices.
Abstract: This paper presents an overview of the Ocean wave kinetic energy harvesting system. Energy harvesting is a concept by which energy is captured, stored, and utilized using various sources by employing interfaces, storage devices, and other units. Ocean wave energy harvesting in which the kinetic and potential energy contained in the natural oscillations of Ocean waves are converted into electric power. The kinetic energy harvesting system could be used for a number of areas. The main applications that we have discussed in this paper are to how generate the energy from Ocean wave energy (kinetic energy) to electric energy that is to eliminate the requirement for continual battery replacement.
Abstract: In communication networks where communication nodes are connected with finite capacity transmission links, the packet inter-arrival times are strongly correlated with the packet length and the link capacity (or the packet service time). Such correlation affects the system performance significantly, but little attention has been paid to this issue. In this paper, we propose a mathematical framework to study the impact of the correlation between the packet service times and the packet inter-arrival times on system performance. With our mathematical model, we analyze the system performance, e.g., the unfinished work of the system, and show that the correlation affects the system performance significantly. Some numerical examples are also provided.
Abstract: The dynamic model of a drill in drilling process was
proposed and investigated in this study. To assure a good drilling quality, the vibration variation on the drill tips during high speed
drilling is needed to be investigated. A pre-twisted beam is used to
simulate the drill. The moving Winkler-Type elastic foundation is used to characterize the tip boundary variation in drilling. Due to the
variation of the drill depth, a time dependent dynamic model for the drill is proposed. Results simulated from this proposed model indicate that an abrupt natural frequencies drop are experienced as the drill tip
tough the workpiece, and a severe vibration is induced. The effects of parameters, e.g. drilling speed, depth, drill size and thrust force on the
drill tip responses studied.
Abstract: In this study, the adhesion of ice to solid substrates
with different surface properties is compared. Clear ice, similar to
atmospheric in-flight icing encounters, is accreted on the different
substrates under controlled conditions. The ice adhesion behavior is
investigated by means of a dynamic vibration testing technique with
an electromagnetic shaker initiating ice de-bonding in the interface
between the substrate and the ice. The results of the experiments
reveal that the affinity for ice accretion is significantly influenced by
the water contact angle of the respective sample.
Abstract: In this paper, the application of sliding-mode control to a permanent-magnet synchronous motor (PMSM) is presented. The control design is based on a generic mathematical model of the motor. Some dynamics of the motor and of the power amplification stage remain unmodelled. This model uncertainty is estimated in realtime. The estimation is based on the differentiation of measured signals using the ideas of robust exact differentiator (RED). The control law is implemented on an industrial servo drive. Simulations and experimental results are presented and compared to the same control strategy without uncertainty estimation. It turns out that the proposed concept is superior to the same control strategy without uncertainty estimation especially in the case of non-smooth reference signals.
Abstract: This paper is focused on issues of process modeling
and two model based control strategies of a fed-batch sugar
crystallization process applying the concept of artificial neural
networks (ANNs). The control objective is to force the operation into
following optimal supersaturation trajectory. It is achieved by
manipulating the feed flow rate of sugar liquor/syrup, considered as
the control input. The control task is rather challenging due to the
strong nonlinearity of the process dynamics and variations in the
crystallization kinetics. Two control alternatives are considered –
model predictive control (MPC) and feedback linearizing control
(FLC). Adequate ANN process models are first built as part of the
controller structures. MPC algorithm outperforms the FLC approach
with respect to satisfactory reference tracking and smooth control
action. However, the MPC is computationally much more involved
since it requires an online numerical optimization, while for the FLC
an analytical control solution was determined.