Abstract: This research paper presents numerical studies of the
characteristics of warhead fragmentation in terms of initial velocities,
spray angles of fragments and fragment mass distribution of high
explosive (HE) warhead. The behavior of warhead fragmentation
depends on shape and size of warhead, thickness of casing, type of
explosive, number and position of detonator, and etc. This paper
focuses on the effects of material properties of warhead casing, i.e.
failure strain, initial yield and ultimate strength on the characteristics
of warhead fragmentation. It was found that initial yield and ultimate
strength of casing has minimal effects on the initial velocities and
spray angles of fragments. Moreover, a brittle warhead casing with
low failure strain tends to produce higher number of fragments with
less average fragment mass.
Abstract: This paper presents a methodology to harvest the kinetic energy of the raindrops using piezoelectric devices. In the study 1m×1m PVDF (Polyvinylidene fluoride) piezoelectric membrane, which is fixed by the four edges, is considered for the numerical simulation on deformation of the membrane due to the impact of the raindrops. Then according to the drop size of the rain, the simulation is performed classifying the rainfall types into three categories as light stratiform rain, moderate stratiform rain and heavy thundershower. The impact force of the raindrop is dependent on the terminal velocity of the raindrop, which is a function of raindrop diameter. The results were then analyzed to calculate the harvestable energy from the deformation of the piezoelectric membrane.
Abstract: New design of a grid for preparation of high density
granules with enhanced mechanical strength by granulation of
dispersed materials is suggested.
A method for hydrodynamic dimensioning of the grid depending
on granulation conditions, hydrodynamic regime of the operation,
dispersity and physicochemical characteristics of the materials to be
granulated was suggested.
The aim of the grid design is to solve the problems arising by the
granulation of disperse materials.
Abstract: Discussion and development of principles of the
uniform nation formation within the limits of the Kazakhstan state
obviously became one of the most pressing questions of the day. The
fact that this question has not been solved "from above" as many
other questions has caused really brisk discussion, shows us increase
of civil consciousness in Kazakhstan society, and also the actuality of
this theme which can be carried in the category of fatal questions. In
any sense, nation building has raised civil society to a much higher
level. It would be better to begin with certain definitions. First is the
word "nation". The second is the "state". Both of these terms are very
closely connected with each other, so that in English language they
are in general synonyms. In Russian more shades of these terms
exist. For example in Kazakhstan the citizens of the country
irrespective of nationality (but mainly with reference to non-kazakhs)
are called «kazakhstanians», while the name of the title nation is
\"Kazakhs\". The same we can see in Russia, where, for example, the
Chechen or the Yakut –are \"Rossiyane\" which means “the citizens
of Russian Federation, but not \"Russians\".
The paper was written under the research project “Islam in modern
Kazakhstan: the nature and outcome of the religious revival”.
Abstract: Mapping between local and global coordinates is an
important issue in finite element method, as all calculations are
performed in local coordinates. The concern arises when subparametric
are used, in which the shape functions of the field variable
and the geometry of the element are not the same. This is particularly
the case for C* elements in which the extra degrees of freedoms
added to the nodes make the elements sub-parametric. In the present
work, transformation matrix for C1* (an 8-noded hexahedron
element with 12 degrees of freedom at each node) is obtained using
equivalent C0 elements (with the same number of degrees of
freedom). The convergence rate of 8-noded C1* element is nearly
equal to its equivalent C0 element, while it consumes less CPU time
with respect to the C0 element. The existence of derivative degrees
of freedom at the nodes of C1* element along with excellent
convergence makes it superior compared with it equivalent C0
element.
Abstract: In this paper, a semi empirical formula is presented based on the experimental results to predict the first pick (maximum force) value in the instantaneous folding force- axial distance diagram of a square column. To achieve this purpose, the maximum value of the folding force was assumed to be a function of the average folding force. Using the experimental results, the maximum value of the force necessary to initiate the first fold in a square column was obtained with respect to the geometrical quantities and material properties. Finally, the results obtained from the semi empirical relation in this paper, were compared to the experimental results which showed a good correlation.
Abstract: The proposed multiplexer-based novel 1-bit full
adder cell is schematized by using DSCH2 and its layout is generated
by using microwind VLSI CAD tool. The adder cell layout
interconnect analysis is performed by using BSIM4 layout analyzer.
The adder circuit is compared with other six existing adder circuits
for parametric analysis. The proposed adder cell gives better
performance than the other existing six adder circuits in terms of
power, propagation delay and PDP. The proposed adder circuit is
further analyzed for interconnect analysis, which gives better
performance than other adder circuits in terms of layout thickness,
width and height.
Abstract: Due to today-s turbulent environment, manufacturing resources, particularly in assembly, must be reconfigured frequently. These reconfigurations are caused by various, partly cyclic, influencing factors. Hence, it is important to evaluate the innovation ability - the capability of resources to implement innovations quickly and efficiently without large expense - of manufacturing resources. For this purpose, a new methodology is presented in this article. Within the methodology, design structure matrices and graph theory are used. The results of the methodology include different indices to evaluate the innovation ability of the manufacturing resources. Due to the cyclicity of the influencing factors, the methodology can be used to synchronize the realization of adaptations.
Abstract: We focus on the excitation and propagation properties
of surface plasmon polariton (SPP). We have developed a SPP
excitation device in combination with a grating structures fabricated
by using the scanning probe lithography. Perturbation approach was
used to investigate the coupling properties of SPP with a spatial
harmonic wave supported by a metallic grating. A phase shift grating
SPP coupler has been fabricated and the optical property was
evaluated by the Fraunhofer diffraction formula. We have been
experimentally confirmed the induced stop band by diffraction
measurement. We have also observed the wavenumber shift of the
resonance condition of SPP owing to effect of a phase shift.
Abstract: Experiments have been performed to investigate the radiation effects on mixed convection heat transfer for thermally developing airflow in vertical ducts with two differentially heated isothermal walls and two adiabatic walls. The investigation covers the Reynolds number Re = 800 to Re = 2900, heat flux varied from 256 W/m2 to 863 W/m2, hot wall temperature ranges from 27°C to 100 °C, aspect ratios 1 & 0.5 and the emissivity of internal walls are 0.05 and 0.85. In the present study, combined flow visualization was conducted to observe the flow patterns. The effect of surface temperature along the walls was studied to investigate the local Nusselt number variation within the duct. The result shows that flow condition and radiation significantly affect the total Nusselt number and tends to reduce the buoyancy condition.
Abstract: In this paper, a theoretical formula is presented to
predict the instantaneous folding force of the first fold creation in a
square column under axial loading. Calculations are based on analysis
of “Basic Folding Mechanism" introduced by Wierzbicki and
Abramowicz. For this purpose, the sum of dissipated energy rate under
bending around horizontal and inclined hinge lines and dissipated
energy rate under extensional deformations are equated to the work rate
of the external force on the structure. Final formula obtained in this
research, reasonably predicts the instantaneous folding force of the first
fold creation versus folding distance and folding angle and also predicts
the instantaneous folding force instead of the average value. Finally,
according to the calculated theoretical relation, instantaneous folding
force of the first fold creation in a square column was sketched
versus folding distance and was compared to the experimental results
which showed a good correlation.
Abstract: Silver nanoparticles were prepared by chemical reduction method. Silver nitrate was taken as the metal precursor and hydrazine hydrate as a reducing agent. The formation of the silver nanoparticles was monitored using UV-Vis absorption spectroscopy. The UV-Vis spectroscopy revealed the formation of silver nanopart├¡cles by exhibing the typical surface plasmon absorption maxima at 418-420 nm from the UV–Vis spectrum. Comparison of theoretical (Mie light scattering theory) and experimental results showed that diameter of silver nanoparticles in colloidal solution is about 60 nm. We have used energy-dispersive spectroscopy (EDX), X-ray diffraction (XRD), transmission electron microscopy (TEM) and, UV–Vis spectroscopy to characterize the nanoparticles obtained. The energy-dispersive spectroscopy (EDX) of the nanoparticles dispersion confirmed the presence of elemental silver signal no peaks of other impurity were detected. The average size and morphology of silver nanoparticles were determined by transmission electron microscopy (TEM). TEM photographs indicate that the nanopowders consist of well dispersed agglomerates of grains with a narrow size distribution (40 and 60 nm), whereas the radius of the individual particles are between 10 and 20 nm. The synthesized nanoparticles have been structurally characterized by X-ray diffraction and transmission high-energy electron diffraction (HEED). The peaks in the XRD pattern are in good agreement with the standard values of the face-centered-cubic form of metallic silver (ICCD-JCPDS card no. 4-0787) and no peaks of other impurity crystalline phases were detected. Additionally, the antibacterial activity of the nanopart├¡culas dispersion was measured by Kirby-Bauer method. The nanoparticles of silver showed high antimicrobial and bactericidal activity against gram positive bacteria such as Escherichia Coli, Pseudimonas aureginosa and staphylococcus aureus which is a highly methicillin resistant strain.
Abstract: Text Mining is an important step of Knowledge
Discovery process. It is used to extract hidden information from notstructured
o semi-structured data. This aspect is fundamental because
much of the Web information is semi-structured due to the nested
structure of HTML code, much of the Web information is linked,
much of the Web information is redundant. Web Text Mining helps
whole knowledge mining process to mining, extraction and
integration of useful data, information and knowledge from Web
page contents.
In this paper, we present a Web Text Mining process able to
discover knowledge in a distributed and heterogeneous multiorganization
environment. The Web Text Mining process is based on
flexible architecture and is implemented by four steps able to
examine web content and to extract useful hidden information
through mining techniques. Our Web Text Mining prototype starts
from the recovery of Web job offers in which, through a Text Mining
process, useful information for fast classification of the same are
drawn out, these information are, essentially, job offer place and
skills.
Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: This paper describes the development of a WLAN
propagation model, using Spectral Analyzer measurements. The
signal is generated by two Access Points (APs) on the base floor at
the administrative Communication School of ESPOL building. In
general, users do not have a Q&S reference about a wireless network;
however, this depends on the level signal as a function of frequency,
distance and other path conditions between receiver and transmitter.
Then, power density of the signal decrease as it propagates through
space and data transfer rate is affected. This document evaluates and
implements empirical mathematical formulation for the
characterization of WLAN radio wave propagation on two aisles of
the building base floor.
Abstract: Guard channels improve the probability of successful
handoffs by reserving a number of channels exclusively for handoffs.
This concept has the risk of underutilization of radio spectrum due to
the fact that fewer channels are granted to originating calls even if
these guard channels are not always used, when originating calls are
starving for the want of channels. The penalty is the reduction of
total carried traffic. The optimum number of guard channels can help
reduce this problem. This paper presents fuzzy logic based guard
channel scheme wherein guard channels are reorganized on the basis
of traffic density, so that guard channels are provided on need basis.
This will help in incorporating more originating calls and hence high
throughput of the radio spectrum
Abstract: A method for solving linear and non-linear Goursat
problem is given by using the two-dimensional differential transform
method. The approximate solution of this problem is calculated in
the form of a series with easily computable terms and also the exact
solutions can be achieved by the known forms of the series solutions.
The method can easily be applied to many linear and non-linear
problems and is capable of reducing the size of computational work.
Several examples are given to demonstrate the reliability and the
performance of the presented method.
Abstract: Today the social marketing was constituted as a tool
of significant value in what he refers to the promotion of changes of
behaviors, attitudes end practices. With the objective of analyzing the
benefits that the social marketing can bring for the organizations that
use it the research was of the exploratory and descriptive. In the
present study the comparative method was used, through a qualitative
approach, to analyze the activities developed by three institutions:
the Recovery Center Rosa de Saron, the House of Recovery for
addicts and Teen Challenge Institute Children's Cancer of the
Wasteland (ICIA), kindred of pointing out the benefits of the social
marketing in organizations that don-t seek the profit.
Abstract: Due to their high power-to-weight ratio and low cost,
pneumatic actuators are attractive for robotics and automation
applications; however, achieving fast and accurate control of their
position have been known as a complex control problem. A
methodology for obtaining high position accuracy with a linear
pneumatic actuator is presented. During experimentation with a
number of PID classical control approaches over many operations of
the pneumatic system, the need for frequent manual re-tuning of the
controller could not be eliminated. The reason for this problem is
thermal and energy losses inside the cylinder body due to the
complex friction forces developed by the piston displacements.
Although PD controllers performed very well over short periods, it
was necessary in our research project to introduce some form of
automatic gain-scheduling to achieve good long-term performance.
We chose a fuzzy logic system to do this, which proved to be an
easily designed and robust approach. Since the PD approach showed
very good behaviour in terms of position accuracy and settling time,
it was incorporated into a modified form of the 1st order Tagaki-
Sugeno fuzzy method to build an overall controller. This fuzzy gainscheduler
uses an input variable which automatically changes the PD
gain values of the controller according to the frequency of repeated
system operations. Performance of the new controller was
significantly improved and the need for manual re-tuning was
eliminated without a decrease in performance. The performance of
the controller operating with the above method is going to be tested
through a high-speed web network (GRID) for research purposes.
Abstract: Chicken feathers were used as biosorbent for Pb
removal from aqueous solution. In this paper, the kinetics and
equilibrium studies at several pH, temperature, and metal
concentration values are reported. For tested conditions, the Pb
sorption capacity of this poultry waste ranged from 0.8 to 8.3 mg/g.
Optimal conditions for Pb removal by chicken feathers have been
identified. Pseudo-first order and pseudo-second order equations
were used to analyze the experimental data. In addition, the sorption
isotherms were fitted to classical Langmuir and Freundlich models.
Finally, thermodynamic parameters for the sorption process have
been determined. In summary, the results showed that chicken
feathers are an alternative and promising sorbent for the treatment of
effluents polluted by Pb ions.